Package Price for Grid Connected 3.3 MW Synchronized Electricity: Please Call For Details Price

Transcription

1 PROPOSED PACKAGE CAPACITY: 3.3 MW (4125KVA) AGN Technology offers the full and complete 3.3 MW of electricity package as a turnkey solution. The enter package shall be install and test for client by AGN Technology engineering department. Package Price for 2.8MW Synchronized Electricity: $2.344m** Package Price for Grid Connected 3.3 MW Synchronized Electricity: Please Call For Details Price **Note: Synchronized 5 generator (Diesel Engine) and through power to one common bas-bar. Payment Terms: 60% advance along with at the time of contract singing, Balance 30% payment after delivery materials to site and remaining 10% will be payment at the time of project handover to the client. Payment Terms for War Zone Countries: 80% advance along with at the time of contract singing, Balance 20% will be payment after delivery materials to the site. Civil Construction and Site Preparation: Project related all civil construction and site preparation is the fully client responsibility. Material Transportation: Inside UAE: Transport all material from AGN Technology warehouse (in UAE) to site location is including with package price. Outside UAE: Transport all material from AGN Technology warehouse (in UAE) to site location is the client responsibility. Security and AGN Technical Staff Accommodations: Inside UAE: A security and AGN technical staff accommodations in UAE is the AGN Technology responsibility. Outside UAE and War Zone Countries: Security, Accommodation and Transportations of all AGN technical staff are the sole responsibility of the client in the war zone countries. It can be discussed in full details once the contract is signed between AGN & its clients. Price Change: All Price are subject to change and alternation without prior notice. Should the prices changes during the contract, AGN will not change price for existing client contract. Contract Cancelation Terms: Once the contract is signed and fully discussed in details, the payment /deposit is for failed and nonrefundable at any circumstance. Delay of payment shall be the same as the cancelation of the project the time both party agree up on.

2 LIST OF MATERIALS FOR PROPOSED PACKAGE S/N Description of materials Quantity Required Remarks 1 Cummins diesel engine generator 5x825KVA=4125KVA Capacity: 825KVA, 400 Volt & 50Hz 2 Synchronization control panel Model: ATSP09 5 No s with common Bus-bar 3 MCCB 5 No s Capacity: 1500Amps, 3 pole Brand: ABB/Schneider 4 Air circuit breaker 1 No Capacity: 6300 Amps, 3 pole Brand: ABB/ Schneider 5 Low Voltage Power Cable As per required Voltage: 400 V Cable size: 400mm² Single core, Copper conductor Insulation: XLPE 6 Grounding Cable As per required Size: 95mm², Y/G copper Conductor 7 Grounding Cable As per required Size: 35mm², Y/G copper Conductor 8 Grounding Cable As per required Size: 16mm², Y/G copper Conductor 9 Control Cable As per required 10 External Fuel Tank 1 No Capacity: 10K gallons 11 Fuel Pipes As per required 12 Fuel Filter 8 No 13 Accessories As per required Options For The Above Package 14 Step-up Power Transformer (0.4KV/33KV or 0.4KV/11KV or as per client requirements) Capacity: 4200 KVA, 50Hz 1 No As per client demand 15 SF6 RMU or SF6 Breaker or VCB Capacity: 630 Amps with all protection system 1 No As per client demand 16 High Voltage or Medium Voltage Power Cable Cable size: 300mm², Three core, Copper conductor As per required As per client demand Insulation: XLPE, Armored steel ware insulated Container 5 No As per client demand Civil constrictions are the client responsibility; AGN should be to quote, If requested by client.

3 SINGLE LINE DIAGRAM FOR 3.3MW SYNCHRONIZED ELECTRICITY

4 MATERIAL DESCRIPTIONS AND DETAIL TECHNICAL SPECIFICATIONS Engine Model: KTA 38 Series Engine. Standby Rating Prime Rating Model 50Hz kva (KW) 60 Hz kva (KW) 50Hz kva (KW) 60 Hz kva (KW) C825 D5e 825 (660) N/A 750(600) N/A Specification: Generator set specification Governor Regulation Class ISO8528G2 Voltage Regulation, No Load ± 1% to Full Load Random Voltage Variation ± 1% Frequency Regulation Isochronous Random Frequency Variation ±0.25% Radio Frequency Emissions IEC through IEC 801.5; MIL STD 461C, Part 9 Compliance Design Bore Stroke Displacement Engine Specifications *Note: Some options may not be available on all models. 4 cycle, in line, turbo Charged and after-cooled 159mm (6.25in.) 159mm (6.25in.) 38 liters (2300in.³) Cylinder Block Engine Twelve-cylinder vee formation, direct injection, fourcycle diesel engine Battery Capacity 890 amps minimum at ambient temperature 32 F (0 C) Battery Charging Alternator 55 amps Starting Voltage 24-volt, negative ground Fuel System Direct injection Fuel Filter Dual spin on paper element fuel filters with standard water separator. Air Cleaner Type Dry replaceable element Lube Oil Filter Type(s) Spin-on paper element full flow and bypass lube oil filters. Standard Cooling System 122 F (50 C) ambient radiator Design Stator Rotor Insulation System Standard Temperature Rise Exciter Type Phase Rotation Alternator Cooling AC Waveform Total Harmonic Distortion Telephone Influence Factor (TIF) Telephone Harmonic Factor (THF) Alternator Specifications Brushless, 4 pole, drip proof revolving field 2/3 pitch Direct coupled by flexible disc Class H 150 C Standby PMG (Permanent Magnet Generator) A (U), B (V), C (W) Direct drive centrifugal blower fan No load < 1.5%. Non distorting balanced linear load < 5% <50 per NEMA MG <3% Standby Power Standby power is defined as the maximum power available during a variable electrical power sequence, under the stated operating conditions, for which a generating set is capable of delivering in the event of a utility power outage or under test conditions for up to 500 hours of operation per year under average of 70% load. Overloading is not permissible. Prime Power Prime power is defined as being the maximum power which a generating set is capable of delivering continuously whilst supplying a variable electrical load. Average load should be 70%. The generator can be overloaded 10% for 1 hour per 12 hours.

5 SYNCHRONIZATION CONTROL PANEL SPECIFICATION ATSP09 SYNCHRONIZATION CONTROL PANEL SPECIFICATIONS LOAD PROPERTIES: Automatic and manual synchronization Can synchronized until 10 generators among them selves and feed the workload Load sharing at generators according to power Automatically start and stop according to load Automatically balancing work hours (co-aging) COMMUNICATION PROPERTIES: Communication over (AQ) bus-bar with electronic engine control units (optional) Alarm message with SMS (optional) Open communication over RS 232 or RS 485 interface Support Motbus RTU protocol (concordant with scada system) INDICATOR PROPERTIES: LCD text indicator All engine and alternator parameters can be watched Engine and alternator protection Keep the records of generator alarms, last 25 records Expansion modules (in and out) With LCD screen in ATSP09 synchronization panels you can measure the following rates and with the stated protection, system reliability put in first place. MEASUREMENTS: DIRECT MEASURES: Oil pressure Coolant temperature Fuel level (optional) Oil temperature (optional) Accumulator voltage Engine circulation Generator frequency Generator phase-neutral voltage Generator inter-phase voltage Generator phase current Generator earth current (optional) Generator phase sequence EXPANDABLE MEASUREMENTS: Generator total active power (KW) Generator total visible power (KVA) Generator total reactive power (KVAr) Generator average power factor (cosφ)

6 HIDDEN MEASUREMENTS: Actual time Left time for the next (maintenance) Generator positive KWh Generator negative KWh Generator KVAh Generator KVArh Number of starter Maximum positive vector slide Maximum negative vector slide PROTECTION SYSTEM: ENGINE PROTECTION: Low oil pressure High coolant water temperature High oil temperature (optional) Low/high frequency cycle Battery charger rectifier error Low/high accumulator voltage Low/high fuel level (optional) ALTERNATOR PROTECTION: Low/high voltage Low/high frequency Extreme voltage Earthling error (optional) Reverse power Wrong phase rotation of alternator Excitation loss CIRCUIT BREAKER PROTECTION: Generator switching off error Generator switching on error

7 MCCB TECHNICAL SPECIFICATION Brand Name ABB Capacity 1500Amps P Pole Three Frequency 50Hz Design Compact Serial number NS 100N Vi 750 Uimp 8KV Icu 50 (V) 380/415~KA 50 Vc-389/ ~50 500/525 ~ Protection system 690 ~ 30 Ics 75% Icu Icw 25 KA/.5s Cat-B Generator switching off error Generator switching on error Over load

8 AIR CIRCUIT BREAKER (ACB) SPECIFICATION Brand name ABB/Schneider Model E4S/f Rated uninterrupted current (at 40 C) Iu [A] 6300 Number of poles 4 Rated service voltage Ue [V ~] 690 Rated ultimate short-circuit breaking capacity Icu 220/230/380/400/415 V ~ [ka] V ~ [ka] /660/690 V ~ [ka] 75 Rated short-time withstand current Icw 80 (1s) [ka] 75 (3s) [ka] Rated short-circuit making capacity (peak value) Icm [ka] 176 Application category (in accordance with IEC ) Isolation behavior (in accordance with IEC ) B Overall Dimensions Fixed: H = 418 mm - D = 302 mm L [mm] 746 Withdraw able: H = D = mm L [mm] 774 Weights (circuit-breaker complete with releases and CT, not including accessories) Fixed [kg] 120 Withdraw able (including fixed part) [kg]

9 STEP- UP POWER TRANSFORMER SPECIFICATION Capacity of power transformer 4000kVA 1 Duty Continuous to suit Max. Ambient 50 C 2 Type Oil immersed Conservator type 3 Cooling ONAN 4 Primary Voltage 0.4KV 5 Secondary Voltage 33kV or 20KV or 11 KV or as per client demand 6 Frequency 50 Hz 7 No. of phase 3 8 Winding Cu wound 9 Vector Group YNd11 10 Primary Connection Delta 11 Secondary Connection Star 12 Tapping ± 7.5% in steps of 2.5% 13 Insulation class of winding Class A 14 Temperature rise Deg. C Top oil 50 C Winding 55.C 15 % Impedance 7.5% +IEC TOL. 16 No load losses 4.5 KW + IEC TOL. 17 HV termination Side mounted cable box 18 LV termination Side mounted cable box 19 Applicable Standards IEC Over all dimension 1350*1500*1500 mm 21 Total Weight 7312 KG 22 Accessories Terminal marking plates Tap Switch (Off- load) Rating Plate Cooling fan/radiators 2 No s earthling terminals Lifting lugs Oil level gauge Drain valve Top filling hole & plug Thermometer with max. pointer Pressure relief device OTI, WTI, Bucholz Relay

10 SF6 RMU TECHNICAL DETAILS 2 no s of 630Amp triple pole, single break, 3- position ( ON, OFF and EARTH ) ring main switches, each with independent manually charged spring mechanism and fully rated earth switch with provision for earth and test of the cable. 2 no s of air insulated cable boxes and cable clams suitable for a 3 core cable up to 300mm². 1 no 250 Amps triple pole, vacuum circuit breaker, with independent manually charged spring mechanism and fully rated earth switch with provision for earth and test of the cable. 1 no air insulated cable box and clamp suitable for a 3- core cable up to 185mm². 1 no mimic diagram on front panel, complete with status indicator. 1 set of positive standard mechanical interlocks. 1 set of current transformer for relay protection. 1 no ABEVA make self powered relay type: MICOM P124 for O/C & E/F protection. 1 no 24V DC shunt trip coil for remote tripping of circuit breaker. 1 set of fully interlocked test access cover. 2 no s of neon indicator lamps /phase comparator sockets for each ring switch. 1 no stud for earthling connection. 1 no pressure indicator and SF6 recharging facility. 1 no PULL TO TRIP mechanism (Suitable shrouded). 1 set of auxiliary terminal. 1 no operating handle. 1 no earth fault indicator, electrical Auto reset (240V AC), complete with solid core current transformer.

11 VACUUM CIRCUIT BREAKER (VCB) TECHNICAL SPECIFICATIONS DESCRRIPTION UNIT SPECIFICATION Rated voltage KV 20 Service voltage KV 20 Rated frequency HZ 50 Rated insulation level (one KV rms 28 min. 50Hz withstand voltage) Impulse withstand voltage KV peak 75 (1.2/50 micro-sec. wave) KV peak 3 second withstand current KA rms 20 Peak withstand current KA peak 63 Internal arc withstand KA rms 25 current (IEC app. A) (1 second) Bus-bar rated current A 630 Auxiliary voltage for spring loading 220V 50HZ For protective relays, control, 24V 50 HZ signaling For heating 220V 50HZ Current transformer (CT) 3 No. ring type (Multiple CT) 150/5A(for metering) and 150/1A(for protection) Potential Transformer (PT) 2 20/0.4KV (Class0.5,50 VA) No. Protection system Earth fault relay Over Current relay for 3 phase (RED, YELLOW, BLUE) Master trip relay (VAJ relay) Trip current supervision relay

12 LOW VOLTAGE CABLE TECHNICAL DETAILS 1 Cable Type Low voltage cable 2 Size of cable(core*area in 1*630 mm²) 3 Applicable Standard IEC Suitable of earthed/unearthed system Earthed/unearthed system 5 Voltage grade (KV) KV 0.6/1 KV 6 Maximum rated conductor C 105 C temperature 7 Max. Allowed conductor C 250 C temperature during short current 8 Continuous current carrying capacity when Load In In Air 745 In Ground 1050 In Duct Conductor Material Annelid copper Shape Standard circular conductor Cross section area Insulation Materials XLPE compound, as per ISO7098 Normal thickness of insulation mm Outer Sheath Materials PVC Extruded or Wrapped Extruded Thickness of sheath (Min.) mm 2.10 Color of sheath Black 12 Overall diameter of cable mm Approx. Net Weight of cable Kg/K m 14 Overall quantity tolerance % ±5% 15 Recommended minimum mm 740 bending radius 16 Max. DC resistance at 20 C Ohm /Km 17 Max. AC resistance at 70 C Ohm /Km

13 FUEL TANK DESIGN SPECIFICATION Capacity Shape Thickness Port Bottom stand Material Painting System Accessories 10,000 Gallons Cylindrical 8mm Inlet, Outlet (For Overflow) 1000mm Ht. Grade A-36, Mild Steel The fuel tank shall be light in color to minimize heating of the fuel by radiant heat sources. Any plating or paint materials shall not be degraded by contact with the fuel Fuel drain (The fuel drain assembly shall be constructed at the bottom side of the fuel tank) Fuel Gauge Man hole Air Vent Ladder Walking Platform at the top