MICROLOK II SYSTEM MAINTENANCE CHECK LIST
|
|
- Joella Lester
- 5 years ago
- Views:
Transcription
1 STATION NAME: Date of commissioning: ZONAL RAILWAY: Date of visit: VISUAL CHECK 1 Check whether Tranzorb KP0A is provided across the card file fan supply 2 Check whether the card file fans are fed from External 2V Check whether there is no 20V AC electrical connections such as light or bulb connection is taken through EI ladder Check that there is no voltage potential between Positive to Earth and Negative to Earth [12V Card file, 2V I/O, 2V/12V Panel] ISOLATION 1 2 Check whether EI ladder (i.e. used for MLK II and Relay Rack wiring) is totally isolated from CT Rack, Data logger & walls Check whether MLK II Racks, Relay Racks & Termination Racks are isolated from floors & walls Check whether DC-DC convertors are isolated from MLK Rack & not connected to earth Check whether MLK signal ground (A2, E22 & C18) is isolated from earth ground Rev 2.0 Doc. No: ENGG/MLKII/MAINT/00001 Page 1 of 6
2 Check whether spare cores of serial communication cables are connected to signal ground at both ends & are isolated from earth 6 Check whether 20V power cable is isolated from MLK II area Check whether converter cum isolators/isolators provided for the serial communication are not bypassed SURGE PROTECTION DEVICE 1 Check whether Transzorb KP16A/6KZ16A is provided for MLK II card file supply 2 Check whether 110V/2V/12V OBO surge suppressor is provided 6 Check whether 20V OBO surge arrester is provided for 20V AC Maintenance/Operator PC s Check 9POP/TCC 82 (RS 22 Isolator) is provided for Maintenance/Operator PC/Data logger Ensure that for Converter/Isolator, if a shielded twisted pair cable is used, then shield should be connected to protective ground at one end only Check whether [Stage I, Stage II & Stage III] surge protections are provided wherever they are applicable Check whether Class B & C surge protections are provided wherever IPS supply is not available Rev 2.0 Doc. No: ENGG/MLKII/MAINT/00001 Page 2 of 6
3 EARTHING 1 Verify that all earth pits are visible and measure the ring earth resistance as per the maintenance schedule 2 Check whether MLK front and back doors are earthed or not Check whether shields of all communication cables are properly connected to earth ground at one end only Check whether proper earth connection is provided for Data logger Check whether surge suppressors (110V, 12V, 2V & 20V ) used are connected to the respective REB & protective fitting Check whether 20V OBO surge arrester is connected to the respective REB & protective fitting Check whether NV Filter box connections are done as per the NV-FLT BO installation check list Check whether painted surface are scraped to the clean metal surface where grounding connections are to be made Check whether the earth connection between REB and the racks earth point are as short and there is no bend or any loose in the earth wire (Green) 10 Check that Armoured Cables used for Control Panel are Connected to REB 11 Check whether all joints are being mechanically and electrically effective (Example. clamped, screwed, bolted, riveted or welded) 12 Check that there are no loose connections in any of the earthing terminations 1 Check that there is no damage to earth wire 1 Earth pits are wetted on regular basis (This is applicable only to non maintenance free earth pit sites) Rev 2.0 Doc. No: ENGG/MLKII/MAINT/00001 Page of 6
4 FIBER 1 Check the db loss for every fiber core using optical power meter 2 Check whether the db loss is within the specified limit of the fiber equipment Check whether redundant path arrangement is working properly (i.e., seamless transfer of one fiber path to the other fiber path) Check whether all fiber loops are neatly dressed with in the splice tray Check whether OFC equipment power supply & LED status is proper 6 Check whether the one end of the armored OFC cable is earthed Check whether the modem is isolated from the metal body of the mounting frame/rack MAINTENANCE ACTIVITY (This shall be performed by Railway Engineer on weekly basis) Ensure there is no dust in MLK II Rack, Operator VDU, Maintenance PC and any other 1 equipment such as Data Logger, IPS etc Check card file cooling fans are properly working & also check for its direction of air flow 2 (i.e., away from card file) Check that cooling fan of DC-DC converters are working properly Check that the glowing of healthy indication in surge suppressors Check that both Input & Output LED indication in DC-DC converter 6 Check that there is no failure indication for the communication link (fiber cut/ modem/server/switching device failure) Rev 2.0 Doc. No: ENGG/MLKII/MAINT/00001 Page of 6
5 Measure the voltages of MLK II card file, I/O & Panel, 110AC, 2V ET and 110V Point supplies 8 Check all the fuses visually for its proper working 9 10 Switch ON the OFF LINE system in diagnostic mode and ensure that both date & time are synchronized to PC time Ensure Back-up of MLK II system logs (event, error & data logs) are taken on regular basis 11 Ensure that EI room is well protected MAINTENANCE ACTIVITY (Monthly) 1 Measure the RING EARTH RESISTANCE VALUE (i.e., less than 1 ohm) 2 Ensure that all the DC-DC converters are working properly in the n+1 configuration Check the healthiness of the change over system by make it ON LINE from OFF LINE (i.e., system A B or system B A ) Switch ON the OFFF LINE system in diagnostic mode and enable the CPS CLEAR mode if required Rev 2.0 Doc. No: ENGG/MLKII/MAINT/00001 Page of 6
6 MISCELLANEOUS 1 Verify whether spare fuses/terminals of all types are readily available at site 2 Check whether Operator VDU, Maintenance PC and Data Logger are working fine Check whether communication between Maintenance and Operator PC s is proper Check whether the LATEST APPLICATION. Program s CRC, CHECKSUM, INSTALLATION ADDRESS, EECUTIVE VERSION, APPL. VERSION are available in the MPC Ensure that both operator VDU & Maintenance PC are provided with latest ANTI VIRUS software 6 Check whether the all display boards related MLK II system are provided in the EI room 8 Check whether the Maintenance Register is properly maintained, as per the UM-6800C Rev1.2 Minimum tools required at site for the proper maintenance of Microlok II system (i.e., Crimping tool 8/96 Pin, Insertion tool 8/96 Pin, Removal tool 8/96 Pin, Locator tool 8/96 Pin, Digital multimeter, Earth meggering meter, Screw drivers, spanners, etc. And Optical power meter, OTDR meter for OFC, if applicable) Special comments (if any): ASTS Engineer Signature: Date: Customer Signature: Date: Next Maintenance visit date: Name: Name: Rev 2.0 Doc. No: ENGG/MLKII/MAINT/00001 Page 6 of 6
Orion BMS Purchasing Guide Rev. 1.2
www.orionbms.com Orion BMS Purchasing Guide Rev. 1.2 Main Components... 2 Orion BMS Unit... 2 Current Sensor... 4 Thermistors... 5 CANdapter... 6 Wiring Harnesses... 7 Cell voltage tap wiring harnesses...
More informationINTER PLANT STANDARD - STEEL INDUSTRY THYRISTOR CONVERTORS FOR ARMATURE AND FIELD OF MAIN DRIVE MOTORS. Corresponding IS does not exist
INTER PLANT STANDARD - STEEL INDUSTRY IPSS THYRISTOR CONVERTORS FOR ARMATURE AND FIELD OF MAIN DRIVE MOTORS Corresponding IS does not exist IPSS: 1-10-038-08 0 FOREWORD 0.1 This Inter Plant Standard has
More informationTOWER MAXI T SINGLE CONVERSION ON LINE UPS SYSTEMS
INSTRUCTION MANUAL TOWER MAXI T SINGLE CONVERSION ON LINE UPS SYSTEMS September 2000 TOWER UPS DISTRIBUTION (PTY) LTD 1 1. INTRODUCTION T A B L E O F C O N T E N T S 1.1 General Description... 3 1.2 Features...
More informationPART NO CP-DOOR FRONT PANEL WINDOW PART NO CP-DOOR FRONT PANEL SECOND WINDOW PART NO CP-DOOR LOCK PART NO. 5026
5010 CP-DOOR FRONT PANEL WINDOW 5015 CP-DOOR FRONT PANEL SECOND WINDOW 5025 CP-DOOR LOCK 5026 CP-DOOR LOCKING CYLINDER 5027 CP MOUNTING BRACKET (PACKET OF 4) 5030 OBSOLETE CP-DOOR PUSH-BUTTON GREEN (HEAD
More informationQualification UEE 30806/07 Cert III in Electrotechnology Electrician
Qualification UEE 30806/07 Cert III in Electrotechnology Electrician Details of the Parties to the Training Contract: Apprentice Name Registration Number Direct Contact Number Registered Training Organisation
More informationValveLink SNAP-ON Application
AMS Device Manager Product Data Sheet ValveLink SNAP-ON Application Communicate with both HART and Foundation Fieldbus FIELDVUE digital valve controllers in the same application Online, in-service performance
More informationMAPNET II Transceiver Installation Instructions
MAPNET II Transceiver Installation Instructions Introduction This publication describes the installation procedure for the following versions of the MAPNET II Transceiver card. 4120/4100-0110 MAPNET II
More informationPSU EN54-4 Power Supplies
PSU EN54-4 Power Supplies Ordering: Models, Sales Order Parts: PSU MXP-549 : 1.5A PSE in 7Ah enclosure MXP-550 : 3.0A PSE in 17/18Ah enclosure MXP-550D : 3.0A PSE in 25Ah enclosure MXP-551 : 5.0A PSE in
More informationBurden Fuse Rating Resistor SAF / SAK6 1NM 10mm M8 12NM SAF / SAK10 2NM 16mm M8 12NM
Contents Section Page 1.0 Introduction 1 2.0 Specification 1-4 3.0 Installation 5-8 4.0 Programming 9-10 5.0 Menus 10-12 6.0 Fault Finding/Diagnostics 12-13 7.0 Communication 13 8.0 Setting Up 13-16 1.0
More informationPower Conversion System The Best Technology for your photovoltaic and storage system
The Best Technology for your photovoltaic and storage system The Best Technology for your photovoltaic and storage system EEI. Experience and Reliability since 1978 EEI s mission started in 1978 coming
More informationOPERATING AND MAINTENANCE MANUAL. Primary Current Injection Test Set. 750ADM-H mk2
OPERATING AND MAINTENANCE MANUAL Product: Type: Primary Current Injection Test Set 750ADM mk2 750ADM-H mk2 DESIGNED AND MANUFACTURED BY: T & R Test Equipment Limited 15-16 Woodbridge Meadows, Guildford,
More informationAMS ValveLink SNAP-ON Applications
Product Data Sheet AMS ValveLink SNAP-ON Applications n Communicate with both HART and FOUNDATION fieldbus FIELDVUE digital valve controllers in the same application n Online, in-service performance diagnostics
More information1291BL Series Technical Specification Single Axis Position and Rate Table System
Datasheet 1291BL Series Technical Specification Single Axis Position and Rate Table System DESCRIPTION The Model 1291BL Single Axis Position and Rate Table System is designed to provide precise position,
More informationProduct Data Sheet. Damper Interface. Features
Damper Interface Product Data Sheet Features Damper Motor drive and limit switch monitoring integrated into a single unit Dual limit switch inputs for confirmation of damper-fully-open and damperfully-closed
More informationCENTROIDTM. AC Brushless Drive. Product Spec Sheet
4 Axis, up to 2 KW motors Brake Output for each axis Overtemp and Overcurrent Protection All-software Configuration Self-cooled Fiber Optic Control CENTROIDTM AC Brushless Drive Product Spec Sheet AC Brushless
More informationSeries 500. Liquid Level Transmitters. Instruction Manual
Series 500 Liquid Level Transmitters Instruction Manual Contents Section Content Page 1 Introduction 1.1 General Overview 3 1.2 Mounting Options 3 2 Installation Notes 2.1 Transmitters 4 2.1.1 Model 510
More informationUNIT 3: GENErAL ELECTriCAL SySTEM DiAGNOSiS
Electrical/Electronic Systems UNIT 3: GENErAL ELECTriCAL SySTEM DiAGNOSiS LESSON 3: TEST electrical circuits I. Types of electrical circuit tests and electrical faults A. Different types of electrical
More informationPreventive maintenance kits
ABB industrial drives ACS800 Preventive maintenance kits All rights reserved. Welcome to the ABB industrial drives, ACS800 Preventive maintenance kits training module. If you need help navigating this
More informationInstallation & Operation Manual
EDL175 Portable Event & Data Logger-Extended Range Installation & Operation Manual BG0447 REV. A3 LIMITED WARRANTY The manufacturer offers the customer a 24-month functional warranty on the instrument
More information1291BL Series Technical Specification Single-Axis Rate and Positioning Table System
Datasheet 1291BL Series Technical Specification Single-Axis Rate and Positioning Table System DESCRIPTION The Model 1291BL Single Axis Positioning and Rate Table System is designed to provide precise position,
More informationConstruction and Wiring Guidelines for Ergon Energy Substation Panels
Construction and Wiring Guidelines for Ergon Energy Substation Panels Table of Contents Purpose and Scope... 1 Responsibilities... 1 Definitions, Abbreviations and Acronyms... 1 References... 1 Panel Wiring...
More informationPretest Module 29 High Voltage Unit 1
Pretest Module 29 High Voltage Unit 1 1. Is a person qualified to work on high-voltage installations when this module is completed? 2. What is the code definition of high-voltage? 3. What is the IEEE definition
More informationDSL-220 MkIII Single Pass Opacity Monitor Measures 0-100% Opacity
Ideal for monitoring opacity and smoke levels in the exhaust gas of industrial combustion or air filtration processes. In situ measurement directly in exhaust gas flow using the widely accepted light transmission
More informationKEOR HP. THREE-PHASE UPS from 100 to 800 kva GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES
KEOR HP THREE-PHASE from 100 to 800 kva GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES Legrand SUPERIOR PERFORMANCE SERVICE CONTINUITY AND ENERGY EFFICIENCY Legrand, world leader
More informationMAGPOWR Spyder-Plus-S1 Tension Control
MAGPOWR TENSION CONTROL MAGPOWR Spyder-Plus-S1 Tension Control Instruction Manual Figure 1 EN MI 850A351 1 A COPYRIGHT All of the information herein is the exclusive proprietary property of Maxcess International,
More informationTechnical Description
Technical Description LUL, 73 Stock Refurbishment Heating, Ventilating & Air-conditioning Multi-stage Thermostat for Saloon 0.1 19-May-02 ISSUED FOR DISCUSSION FK DC Rev. Date Description By Check Copyright
More informationSECOND GENERATION Use this guide with unit serial number prefix beginning with BWF using Terra Power separator.
Technical Information and Diagnostic Guide for SECOND GENERATION Use this guide with unit serial number prefix beginning with BWF using Terra Power separator. This guide will assist you in becoming more
More informationKEOR HP. THREE-PHASE UPS from 100 to 800 kva GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES
KEOR HP THREE-PHASE from 100 to 800 kva GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES Legrand SUPERIOR PERFORMANCE SERVICE CONTINUITY AND ENERGY EFFICIENCY Legrand, world leader
More informationINTECH Micro 2300-RTD6
INTECH Micro 2300-RTD6 6 Channel RTD Input Station Overview. The Intech Micro 2300 Series is a system of modular I/O Remote Stations, that add an even lower cost option to Intech s already extensive intelligent
More informationFuel Cell Lab Manual. Non Conventional Energy Systems Facility. Non Conventional Energy Systems Facility. Boiler House
Fuel Cell Lab Manual Non Conventional Energy Systems Facility Boiler House Department of Mechanical Engineering IIT Kanpur System Description The Nexa system provides up to 1200 watts of unregulated DC
More informationEVO AT SERIES BATTERY CHARGER
EVO AT SERIES BATTERY CHARGER AT SERIES BATTERY CHARGER P R O D U C T PATENT PENDING hindlepowerinc.com 610-330-9000 Evo AT Series battery charger designed with YOU in mind. Evo AT Series battery charger
More informationElectrical Safety. Presented By- C S Chakraverty. L&T Construction ( MMH ) Head- E&I Operation
Electrical Safety Presented By- C S Chakraverty Head- E&I Operation L&T Construction ( MMH ) Objective of the session Create an awareness about importance of electrical safety in our day today activities,
More informationWind display type WSDI-2
USER s MANUAL/INSTALLATION NOTE Wind display type WSDI-2 Input and wiring Mounting Document no.: 4189350032C Table of contents 1. INTRODUCTION... 3 UNPACKING... 3 2. INPUT AND WIRING INSTRUCTION... 4 3.
More informationN Daily Weekly Monthly Every 3 months. Every 6 months 1 Remove any materials not related
MV / LV cabins maintenance The operation and maintenance of the cabins are meant to ensure high reliability (i.e. the early detection of anomalies, the failure prevention and monitoring functional) and
More informationInstallation, Operation and Maintenance Manual Stancor SSD & SL Series Pumps
Installation, Operation and Maintenance Manual Stancor SSD & SL Series Pumps EI-700-008 Rev -- Table of Contents Safety Guidelines 3 Caution 4 Wiring 4 Maintenance 4 Nameplate format 4 Prior to Operation
More informationEFI Harley Davidson 1340 EVO
Floppy Disc Request Form If you do not have a CD-Rom drive and would like to receive the program and the alternate maps for your model on a 3 1/2 floppy disc, please fax this form to Dynojet at 1-702-399-1431
More informationAT SERIES EVO BATTERY CHARGER
AT SERIES EVO BATTERY CHARGER AT SERIES BATTERY CHARGER P R O D U C T hindlepowerinc.com 610-330-9000 AT Series evo. A battery charger designed with YOU in mind. AT Series evo is HindlePower s next generation
More informationEPS/ELA-Series User Manual EPS/ELA 250W
EPS/ELA-Series User Manual EPS/ELA 250W EPS Stromversorgung GmbH Tel: +49 (0)821 570451 0 Index 3 Page: 1 Table of contents: Page 1. Features of ELA-Series... 3 1.1 Basic Functions... 3 1.2 Options...
More informationApplication Specification Circular Plastic Connector (CPC) Series 45 System 05 AUG 14 Rev D
Application Specification Circular Plastic Connector (CPC) 114-13137 Series 45 System 05 AUG 14 Rev D NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions
More information825-P Modular Protection System for motors Specification Guide
Specification Guide 1.0 General 1.01 The motor protection relay shall have a current operating range of 0.5 and 5000 amperes. 1.02 The motor protection relay shall provide current measurement-based protection
More information2O3D3-19A REVB MOUNTING
Practice Section 1672 Issue 6, September 2014 MOUNTING ETL LISTED CONFORMS TO UL STD 60950-1 CONTENTS Multiple Patents Pending CLEI Code SOM2300C, CPR 204577 PAGE 1 INTRODUCTION... 2 1.1 Reason for Reissue...
More informationAFM500X Automatic Flashing Module
AFM500X Automatic Flashing Module The Power-Tronics AFM500X Automatic Flashing Module is a convenient and compact optional build up module for all Power-Tronics UVR and XR series Universal Voltage Regulators.
More informationIRT 4000 AT-S/M/L. Technical Manual. quality IN MOTION. quality IN MOTION
IRT quality IN MOTION www.irtsa.com 4000 AT-S/M/L Technical Manual IRT quality IN MOTION E2 0 8 4 1 5 September 2013-Rev. 5 UL Requirements Drives Series 2000 / 4000 AT 1. Field wiring terminal to use
More informationIBER DISTRIBUTION FRAME (FDF) FOR EXCHANGE SIZE 900MM x 2200MM x 300 MM
F 19 Rack Exchange & Shelf Unit IBER DISTRIBUTION FRAME (FDF) FOR EXCHANGE SIZE 900MM x 2200MM x 300 MM 1. General : 1.1 This specification covers the requirements of the fiber distribution frame (FDF)
More informationPOWERTRONIX QUASAR 5-40 KVA
POWERTRONIX QUASAR 5-40 KVA DT 0251 E00 TECHNICAL DATA Rev. Description Date Checked Released Date Type of doc. Page n Pag. Tot. ISSUED 07.03.2000 E.Borsa 07.03.2000 Approved A.Gorlani Pag.1/6 Cod. DT251
More information2 Unit Petrol Engine Spare parts kits for 4 WD Nissan Patrol
04-62-70001 4 WD NISSAN PATROL STATION WAGON SGL, 4500 cc 2 Unit Petrol Engine 04-62-70002 Spare parts kits for 4 WD Nissan Patrol 4 Set Station Wagon 04-62-70003 Belt-Fan 11720-03J00 4 Each 04-62-70004
More informationMP24 Motorized Potentiometer
MP24 Motorized Potentiometer The Power-Tronics MP24 Motorized Potentiometer is an optional add-on module for Power-Tronics voltage regulating systems designed to allow the voltage regulator to receive
More informationSentinel Field Satellite Controller
WARNING HIGH VOLTAGE 115V M AP Sentinel Field Satellite Controller Installation Instructions Important: For your protection and the safety of the product user, please comply with all Caution and Warning
More informationInstalling Power Components
This chapter provides instructions on how to install and reinstall power components in the Cisco NCS 4016 chassis. It also covers connecting and disconnecting power and powering on the chassis. The Cisco
More informationCombiTac Overview. CombiTacline Industrial Connectors
CombiTac Overview CombiTacline Industrial Connectors CombiTac Modular Connector System As a solution provider, Stäubli offers customers worldwide A-Z support in designing their own 100 % customized CombiTac
More informationUninterruptible Power System
USER'S MANUAL Emergency Backup Power Supply For Use With Computer Loads Only Power Surge/Noise Protection Intelligent Auto-Shutdown Software Internet Line Protection Cost Efficiency UPS AVR Protection
More informationStatic frequency converter couples US paper mill s 25-Hz and 60-Hz electricity grids
Static frequency converter couples US paper mill s 2-Hz and 0-Hz electricity grids Before 0 Hz was adopted as the standard frequency for electricity distribution in the USA, power companies across the
More informationIB IL 24 PWR IN/F-D IB IL 24 PWR IN/F-D-PAC
IB IL 24 PWR IN/F-D IB IL 24 PWR IN/F-D-PAC Inline Power Terminal With Fuse and Diagnostics Data Sheet 5569C 02/2003 # # $ ' ) The IB IL 24 PWR IN/F-D and IB IL 24 PWR IN/F-D-PAC only differ in the scope
More informationS P E C I F I C A T I O N
T E N D E R S P E C I F I C A T I O N NO: BHE/PW/PUR/KKT-ELE/627 FOR HANDLING AT SITE STORES/STORAGE YARD, TRANSPORTATION TO SITE OF WORK, COMPLETE ERECTION, CHECKING OF CALIBRATION, TESTING, COMMISSIONING
More informationDispense interface converter NA-8 (RS-485/RS-232 to non-addressable RS-422/RS-485/RS-232 and backwards)
Dispense interface converter NA-8 (RS-485/RS-232 to non-addressable RS-422/RS-485/RS-232 and backwards) TECHNICAL GUIDE Review date: 20 January, 2017 Revision number: 1.02 TECHNOTRADE LTD CONTENT REVISION
More informationStandby Amper VOLTAGE
INTRODUCTION Aksa power generation system, providing optimum performance, and reliability, for stationary standby, prime power, and continuous duty applications. All generator sets are factory build, and
More information5001TCP SPEED CONTROLLER
VARIABLE SPEED DRIVE CONTROLLER INSTALLATION AND SETTING UP MANUAL 5001TCP SPEED CONTROLLER With PC101 Torque Limit Control WARNING Disconnect all incoming power before working on this equipment. Follow
More informationUS Models Only EFI Harley Davidson Twin Cam 88 Touring Models. Floppy Disc Request Form
Floppy Disc Request Form If you do not have a CD-Rom drive and would like to receive the program and the alternate maps for your model on a 3 1/2 floppy disc, please fax this form to Dynojet at 1-702-399-1431
More informationHYDROVAR IncReAseD flexibility AnD control with new generation
HYDROVAR Increased flexibility and control with new generation HYDROVAR, the modern variable speed pump drive is taking pumping to a new level of flexibility and efficiency. m Motor or wall mountable m
More informationEVO SERIES BATTERY CHARGER SERIES BATTERY CHARGER
EVO SERIES BATTERY CHARGER SERIES BATTERY CHARGER Evo Series battery charger designed with YOU in mind. Evo Series battery charger is a next generation SCR-based utility battery charger. This evolutionary
More informationThis generator set has been designed to meet ISO 8528 regulation. This generator set is manufactured in facilities certified to ISO 9001.
This generator set has been designed to meet ISO 88 regulation. This generator set is manufactured in facilities certified to ISO 900. This generator set is available with CE certification. Enclosed product
More informationThis generator set has been designed to meet ISO 8528 regulation. This generator set is manufactured in facilities certified to ISO 9001.
This generator set has been designed to meet ISO 8528 regulation. This generator set is manufactured in facilities certified to ISO 9001. This generator set is available with CE certification. Enclosed
More informationUninterruptible Power System
USER'S MANUAL Emergency Backup Power Supply For Use With Computer Loads Only Power Surge/Noise Protection Intelligent Auto-Shutdown Software Internet Line Protection Cost Efficiency AVR Protection Compact
More informationThis generator set has been designed to meet ISO 8528 regulation. Enclosed product is tested according to EU noise legislation 2000/14/EC
This generator set has been designed to meet ISO 88 regulation. This generator set is available with CE certification. Enclosed product is tested according to EU noise legislation 000//EC Phase Ratings,
More information120V and 230V Modem Upgrade Instructions for AlphaEclipse StreetSmart Signs
120V and 230V Modem Upgrade Instructions for AlphaEclipse StreetSmart Signs Introduction This document explains how to install a 120V or 230V modem into the following AlphaEclipse StreetSmart signs: 17X,
More informationCUSTOMIZED OPTIONS FOR 1-WEEK DELIVERY
IN STOCK GUARANTEED! Benshaw is offering the most Rugged, Reliable and Proven soft starter for your most demanding and tough applications CUSTOMIZED OPTIONS FOR 1-WEEK DELIVERY A Regal Brand 2017 Information
More informationDSL-240 MkIII Single Pass Dust Monitor Measures mg/m 3 using DDP
Ideal for monitoring dust levels in the exhaust gas of industrial combustion or air filtration processes. Innovative Dynamic Detection Principle (DDP) measurement technique Immune to gradual reductions
More informationOutdoorXUPS-600AHV-8364
OutdoorXUPS-600AHV-8364 TSi Power s OutdoorXUPS-600AHV-8364 provides secure and uninterrupted 230 vac power to critical loads. 1) Weather-tight metal cabinet (IP44 or NEMA 3R rated) 2) 2A and 2B are wide
More informationProduct Guide: Series III Pump Control Board Set (RoHS)
revised 04/08/10 Description: The Series III Pump Control Board Set provides motor drive and pump control for a wide assortment of pumps from Scientific Systems, Inc. The assembly consists of two circuit
More informationEngineering the Future of Payment Solutions
Subject: Preventative Maintenance and Cleaning Procedure for MSM Bill Validator Objective: To outline a procedure to ensure your Cashcode bill validator continues to operate as per factory specifications
More informationBattery Monitoring Why Technology Matters. Mats Karlstrom V.P. Sales & Marketing, Alber
Battery Monitoring Why Technology Matters Mats Karlstrom V.P. Sales & Marketing, Alber 1 Agenda Introduction Why is battery monitoring needed? Example of battery failure Why are resistance measurements
More informationThis generator set has been designed to meet ISO 8528 regulation. This generator set is manufactured in facilities certified to ISO 9001.
This generator set has been designed to meet ISO 88 regulation. This generator set is manufactured in facilities certified to ISO 900. This generator set is available with CE certification. Enclosed product
More informationSitras SCS, -RCI, -FFP, -TTU
Sitras SCS, -RCI, -FFP, -TTU control system for traction power supply Remote control interface Frame fault protection Transfer trip unit siemens.com/rail-electrification The Sitras SCS station control
More informationLCD Annunciator Installation Instructions
4603-9101 LCD Annunciator Installation Instructions Cautions and Warnings DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED. Upon unpacking your Simplex product, inspect the contents of the carton
More informationThe 4HR-UPS 220V ac output is provided via a Pure Sine Wave inverter, allowing it to be backed up by 2x 12V standby batteries.
1 Elmdene International Ltd Tel: +44 (0)23 9269 6638 3 Keel Close, Interchange Park, Fax: +44 (0)23 9266 0483 Portsmouth, Hampshire, PO3 5QD, UK Web: www.elmdene.co.uk STANDBY 220V AC POWER SYSTEM IDEAL
More informationAT EVO SERIES BATTERY CHARGER
STANDARD FEATURES 5 YEAR WARRANTY EVO AT Series Battery Charger is HindlePower s next generation SCR-based utility battery charger. This evolutionary product is revolutionary in its design and operation
More informationINTER PLANT STANDARD STEEL INDUSTRY SPECIFICATION FOR STATIC EXCITATION CONVERTORS FOR SYNCHRONOUS MOTORS (FIRST REVISION)
INTER PLANT STANDARD STEEL INDUSTRY I P S S SPECIFICATION FOR STATIC EXCITATION CONVERTORS FOR SYNCHRONOUS MOTORS (FIRST REVISION) Corresponding IS does not exist IPSS: 1-10-036-12 0 FOREWORD 0.1 This
More informationAnnexure B (1)- Engineering Instructions for Installation of Aerial OFC
Annexure B (1)- Engineering Instructions for Installation of Aerial OFC INSTALLATION PRACTICE OF SELF SUPPORTING METAL FREE AERIAL OPTICAL FIBER CABLE 1. SCOPE: This Engineering Instruction (EI) deals
More informationTPM Fuse Panel Installation Guide. Document INS-727XXXXXXX This manual covers the following part numbers- Trimm 727XXXXXXX Family
TPM Fuse Panel Installation Guide Document INS-727XXXXXXX This manual covers the following part numbers- Trimm 727XXXXXXX Family Table of Contents Section 1- General Information... 3 1.1 - Product Description...
More informationOne-Stop Service: Monitoring and Managing.
One-Stop Service: Monitoring and Managing. The highest quality from the market leader Solar-Log devices are the most accurate and reliable data loggers on the market. Offer your customers high-quality
More informationCutler-Hammer. Instructions for Installation, Operation, and Maintenance of the AMPGARD Reduced Voltage Soft Starter
Operation, and Maintenance of the Instruction Bulletin Read and understand these instructions before attempting any installation, operation, or maintenance of the. This equipment shall be installed and
More informationSTANDARD OWNER S MANUAL
WILLIE 1.0 STANDARD OWNER S MANUAL OPERATION, MAINTENANCE, & TROUBLESHOOTING STANDARD INSTRUCTIONS FOR ALL SYSTEMS DSE 3100 4/28/2011 Willis Power Systems 2950 N Martin Springfield, MO 65803 417.831.2520
More informationACCESSORIES FOR LPOF, HPPT AND XLPE HIGH VOLTAGE CABLE SYSTEMS PRODUCT CATALOGUE
ACCESSORIES FOR LPOF, HPPT AND XLPE HIGH VOLTAGE CABLE SYSTEMS PRODUCT CATALOGUE hvgrid-tech designs and manufactures high voltage cable accessories for all types of cable systems, ranging from 69 kv to
More informationSkyHawk M1620 Satellite Modem. Installation and Setup Guide READ ME FIRST
SkyHawk M1620 Satellite Modem Installation and Setup Guide READ ME FIRST 2 Location, Location, Location Installing a SkyHawk M1620 Satellite Modem is not the same as installing a satellite dish for television.
More informationINTELLITROL. scully. Scully s Intellitrol System. Intellitrol is a state of the art microprocessor based system that provides:
INTELLITROL Overfill Prevention Control Unit with Optional Ground Verification and Vehicle Identification Features. Scully s Intellitrol System is the most advanced terminal overfill prevention and ground
More informationWiring Harness 1. Remove left hand footwell trim panel from driver s footwell. Typically secured by several Philips head screws.
Installation There are four segments to the installation; wiring harness, EDIS and Megajolt, coil pack, and Timing wheel and VR sensor. If the car needs to be driven, install everything except the coil
More informationHIB Enclosed Inverter User Guide
HIB Enclosed Inverter User Guide (0.75kW~22kW) V1.2.0 Contents 1 Safety information...1 2 Technical Data...2 3 Motor Connection...4 4 Operation...5 5 Single phase circuit diagram...7 6 Three phase circuit
More informationINSTRUCTION MANUAL MODEL PS VDC POWER SUPPLY
222 W. Memorial Road, Oklahoma City, OK 73114-2317 Phone: 1-800-624-7697 Fax: 405-755-8425 www.magpowr.com E-mail: magpowr@magpowr.com INSTRUCTION MANUAL MODEL PS-24 24 VDC POWER SUPPLY All of the information
More informationINDIAN INSTITUTE OF TECHNOLOGY KANPUR
INDIAN INSTITUTE OF TECHNOLOGY KANPUR Tender tice. 21/Elect./2018 SCHEDULE OF QUANTITY Name of Work: Construction of second floor above central block at ACES building (SH: Electrical works). Name of the
More informationSwitchgear Skid, C1192
CUSTOM SOLUTIONS 15kV Modular Stairs stored on floor in front of battery bay Ground grid stored on front tongue of trailer Stairs deployed for unit access Storage box for fencing materials and other parts
More informationEnclosed product is tested according to EU noise legislation 2000/14/EC. Voltage kva kw kva kw Amp 400/ ,00 880, ,00 824, ,00
This generator set has been designed to meet ISO 8528 regulation. This generator set is manufactured in facilities certified to ISO 9001. This generator set is available with CE certification. Enclosed
More informationSafety Precautions Product Contents Product PIN Diagram LED indicators Product Dimensions Installation of Panel with Casing Wire Legend Power Wiring
www.zkteco.com Safety Precautions Product Contents Product PIN Diagram LED indicators Product Dimensions Installation of Panel with Casing Wire Legend Power Wiring Diagram FR1200 Connection Weigand Connection
More informationAT30 SERIES BATTERY CHARGER
STANDARD FEATURES 5 YEAR WARRANTY 5 Year Product Warranty Universal main control board operates in any AT Series charger Alarm assembly with local LEDs and summary relay contact for AC Failure, DC Failure,
More informationTender for procurement of Passive Components of LAN & Wi-Fi and their installation. Corrigenda. Annexure/Clause For Read
Tender for procurement of Passive Components of LAN & Wi-Fi and their installation Corrigenda Sl. No. Annexure/Clause For Read Item Specifications Item Specifications 1. Annexure-I, Point No. 1.3 24 Port
More informationIB IL 24 SEG/F. Function. INTERBUS Inline Segment Terminal With Fuse. Data Sheet 5656B
INTERBUS Inline Segment Terminal With Fuse Data Sheet 5656B 02/2001 # $ # $ ) This data sheet is intended to be used in conjunction with the Configuring and Installing the INTERBUS Inline Product Range
More informationINDUSTRIAL GENERATOR SERVICE
INDUSTRIAL GENERATOR SERVICE PREVENTATIVE MAINTENANCE PROGRAM Customer: Date: Contact Person: Work Order #: Contact Number: ( ) Technician: INSPECTION COMPONENTS 1. GENERAL Check fuel tank level. Check
More information9-2 FAULT CODE DIAGNOSTICS AND REPAIR PROCEDURES
SERVICE BULLETIN (Not applicable to Mack Trucks Australia) (Supersedes bulletin SB-221-032 dated 3/20/03) NUMBER: SB-221-032 DATE: 12/4/03 MODEL: All 9-2 FAULT CODE DIAGNOSTICS AND REPAIR PROCEDURES A
More informationUser Manual. Solar Charge Controller 3KW
User Manual Solar Charge Controller 3KW 1 CONTENTS 1 ABOUT THIS MANUAL... 3 1.1 Purpose... 3 1.2 Scope... 3 1.3 SAFETY INSTRUCTIONS... 3 2 INTRODUCTION... 4 2.1 Features... 4 2.2 Product Overview... 5
More informationTENDER FOR FOR 2 X 1010 KVA, 1500 RPM, 415 V DG SETS FOR CONSTRUCTION OF NEW CDRI CAMPUS AT SITAPUR ROAD, LUCKNOW (U.P.) SUMMARY OF PRICE BID
TENDER FOR FOR 2 X 1010 KVA, 1500 RPM, 415 V DG SETS FOR CONSTRUCTION OF NEW CDRI CAMPUS AT SITAPUR ROAD, LUCKNOW (U.P.) SUMMARY OF PRICE BID S.NO. HEAD DESCRIPTION AMOUNT (Rs.) 1 A DG SETS & ACCESSORIES
More informationSPECIAL SPECIFICATION 6894 Communication Cabinet
2004 Specification CSJ 0353-04-085, etc. SPECIAL SPECIFICATION 6894 Communication Cabinet 1. Description. Furnish and install communication cabinet to include the installation of the foundation, cabinet,
More information