ASSEMBLY AND SPARE PARTS CABIN APPROVED KUBOTA M8560 COD. AG624. Models : M6060 D- M7060 D- M8560 D- M9960 D

Transcription

1 ASSEMBLY AND SPARE PARTS CABIN APPROVED KUBOTA M8560 COD. AG624 Models : M6060 D- M7060 D- M8560 D- M9960 D

2

3 OWNER'S MANUAL MAINTENANCE Version 15 July 2009 Thanking you for your purchase, we list some short and simple maintenance procedures to maintain efficient and in good condition your cabin. CARE and CLEANING To clean the inside it is recommended to take apart and clean the carpets furniture not soak in water. The fixed cover is washable with water. REGISTER DOORS After assembly of the cabin on the tractor may be necessary to adjust the closing of the doors by adjusting the fastening of the lock. This operation is repeated every time it is disassembled and reassembled the cabin. To maintain an effective closure of the goalkeeper we strongly advise you to work with the doors open because the prolonged vibration could affect the hinges. HEATING SYSTEM \ FAN (tractors, water-cooled) Please note that to switch from heating to ventilation is necessary to close the tap hot water output which is located in the cab CLEANING AND REPLACEMENT FILTERS We recommend that you blow the air intake filter every 150 hours of operation of the tractor. Instead every 1000 working hours should clean the system always full with compressed air. To access the system must remove the plastic roof or sheet after removal of the silicone coating. In replacement of the roof we recommend running again sealing with the use of silicone. And 'advisable to change the filter once a year 1. For activated carbon filters have a limited life so they use only advice during treatments and to replace it with a normal filter for other jobs. The active carbon filter should be stored in the outer carton. Filter life depends very much working condition, however the average length are 150 hours of work. AIR CONDITIONING SYSTEM Recall that for a smooth operation is essential to keep the radiator clean place on the roof and the position of the gas in the compressor. To clean the radiator using compressed air max. 3.5 bar to avoid damaging the radiant body. To charge the compressor does not exceed the specified weight (0.7 kg for large compressors and 0.5 kg for small compressors) to not send the system overpressure. For more details refer to the manual of the specific manufacturer. For any further information, our staff and our technicians are at your disposal.

4

5 AGRITAL S.r.l. Via Leonardo Da Vinci, Arzago d Adda (BERGAMO) - ITALY TEL : FAX : agrital@agrital.com WEB site: WARRANTY REGISTRATION Dear customer, The warranty is valid only if it is completely filled and sent within 15 days from the date of purchase to Agrital srl. The warranty can be sent by fax or via . Model of the car or tractor: Number freshman cabin: Date of purchase: Company Name dealer: The guarantee is valid for 12 months only valid on particular defective in factory, is not recognized by the user for damaged parts or normal wear and tear. For the air conditioning system also fill out the warranty of the manufacturer of the system. The customer declares to have received the instructions for use and maintenance, have been informed properly by the dealer on the proper use of the cabin, its installations. For use of any PPE for the use of the cabin follow the instructions and directions of your doctor's work. The dealer confirms that you have installed, or you did install the cab in compliance with all instructions provided by the manufacturer in order that the approval OECD- SAE is valid. Stamp of authorized dealer: Date and place: Name or company name: (please print) signature:

6

7 The following is a brief description for installing the product. Remove from the machine the following elements: front door handles edge (bolted to the fender) ladder climb toolbox plate holder fenders roll bar Rear Put in place of the roll bar rear bench provided (image A) and fix it in the same places and in the same manner in which they are attached the various attacks of the roll bar is the original wagon is the platform. Use the original screws. (Photo 1a-b-c). photo 1a = FIX THE REAR BRACKET WHIT ROLLBAR BASE ORIGINAL.

8 photo 1b = FIX TUBE photo 1c = FIX REAR SEAT Attack on the uprights of the rear bracket the adhesive seal to close the light that remains between them and fenders. photo 2a = light that remains between rear bracket and fenders = COD. TAB.42 cod

9 Positioned the bench can be mounted fenders fixing them in the same places where they were previously set. Use the original screws (photo 3a, 3b). Fix the bench and fenders tightening the screws. - Photo indicative. photo 3b= fix fenders REMOVE THE SUPPORTS MIRROR WHICH ARE ON THE SIDE OF THE HOOD BEFORE PUT THE CABIN.

10 Glue the adhesive gasket on the uprights of the front (to close the gaps between the front and hood). LOWER the cabine. (ATTENTION not to hit parts of the tractor, proceed slowly). Check seals and rubber close perfectly. Connect the rear cross member of the cabin to the silent block pre-mounted on the bench, using the holes with existing screws (n 1 + 1) TE 12x provided. (Photo 6a) do not tighten the screws. Place the front brackets, to the right and left of the round hood, fixing the existing holes with screws (n 4 + 4) TE20x (original). photo 7a. Photo 7a = front bracket ( dx e sx) COD. TAB cod Attach the bracket cantilever welded on the front with the pre silent block mounted on the bracket below using the 'using existing slot (n 1 + 1) Screw TE 12x supplied. (Photos 8a) Getting back the optimal position of the cab and tighten the screws. IN THE EVENT OF A TRACTOR WITH LOADER: In the case of tractor with shovel the car must be secured to the platform by means of screws TE 12x (two per side) provided. DON T USE THE BRAKET AND Are also supplied two brackets (cod and see figure) which can be screwed to the merger of the tractor at the blade, it should not touch the platform but serve only as a stop in the event of rollover. They are based on the model of the blade they may need to be modified in place.

11 Staffe cod e Positioning coatings and finishes: place keeping the seat fully forward the sheet with pre mounted the 'back door and seal: introducing the workpiece into the cabin, place it to the uprights of the bench (for part visible from the 'inside of the machine) and the rear cross member of the cab. Lock the optimal position with self drilling screws. Any drafts are to be closed with silicone. (Photo 9a) Place the sheets front closure under hood (right and left) and secure with self drilling screws to the posts of the front. (10 photos) Place the carpet and, if desired, secure with self drilling screws. Place arrows using the original structure, the original screws, on the brackets welded to the rear. (Photo 11a) Place the bracket to the toolbox using the existing holes and the original screws. (Photo 12a ) Place the bracket to the toolbox using the existing holes and the original screws. (Photo 12a). photo 12a = tool box with mounting bracket COD. TAB. 38 cod

12 Place the plate using the bracket welded on the machine and the original screws moving too light. (Photo 13a) photo 13a = number plate screwed to existing media, with original screws and inserting the original light. COD. TAB.36 cod Place the baton as originally supporting the regulator using the relay to "L" supplied (hole 14a). photo = 14th position controller COD. TAB.39 cod Place arrows front. foto 15a = arrows front COD. TAB. 27 cod

13 Insert the locking rear door, bringing it down behind the seat and secure with self drilling screws. Insert the fasteners to tighten the front openings that remain between the cabin and dashboard, staring too 'them with self drilling screws. ANY REMAINING SLOTS MUST BE CLOSED WITH SILICON. coatings extra In the case of coatings and fender under the seat precede with their positioning before dropping the car and let the material may abound to cut the excess only once positioned and secured the cabin. Fender liners are glued on the wings. Be shaped in work the housing for the rear lever on the fender dx.under the dash should be fixed with self drilling sheet metal and closed compartments of the pedals with the supplied rubber. Seal the joints with silicone sheets. Heating (optional): Connect with the connector supplied, the water flow from the pump of the tractor: * pressure pipe system is marked: Connect with the connector supplied, the return water:

14 - The heating pipes should be protected by plastic tube provided (for the exposed between the cab and engine compartment) At the end of it all start the engine and let it warm up (at least 5 minutes). Once in temperature off and wait at least 10 minutes to cool. At this point do refilling of water in the radiator.

15 ELECTRICAL CONNECTION FOR CONNECT THE LIGHTS, AND OTHER ACCESSORIES ARROWS FOR STOPPING WITH THE CAR YOU CAN CONNECT AS FOLLOWS: We remain at your disposal for any clarification We remain at your disposal for any clarification Agrital srl.

16 COMPONENTS

17 FRONT AND SIDE:

18 number qt Description CODICE 1 1 Crystal front Crystal door Crystal front fixed Crystal rear Crystal windows fixed Crystal rear oblò Handle for door right and left Support lock DX and SX Gasket for support lock Plate for handle Handle button -Compl Hinge sup. door Seal for hinge sup Shock absorber for door Lock Right and Left Acknowledgement lock Rearview Mirror EURO3 right / left * Front shock absorber crystal L Rear shock absorber crystal L Support Amm. Compl. crystal Wiper motor Rod wiper Brush Thickness Nylon Zipper Hinge Nylon Compl Crystal Handle Front Support front indicators (by screw) Match Brass Heat. handle Thick brass handle LIGHT prior work (optional rear) Nylon crystals Grommet crystals Hardware for fixed glass socket flashing * = OPTIONAL DA RICHIEDERE AL MOMENTO DELL' ORIDINE.

19 POSTERIORE E COMPLEMENTI: N QT DESCRIPTION CODE 35 1 Handle rear window License plate Holder Toolbox Support extension block (yellow) mt profile crystals mt gasket mt gasket

20 42 3mt adhesive gasket Complete Rear Bench Silent Block (ant = post) A 4 Side screw silent block (front) TE M10x30 10,9 45B 4 Screw side silent block (rear) TE M10x70 8,8 46A 2 Central screw silent block (front) TE M12x70 10,9 46B 2 Central screw silent block (rear) TE M12x110 10, Closing Compl. Rear (c / crystal) Bracket door flashing ABS roof Group heating (optional) Filter only with heating Locking compartment filter holder (with max.) Closing filter compartment door (WITHOUT Heat.) Front closure SX Front closure DX Front bracket SX - Engagement original Front bracket DX - Engagement original A 2 Closure mudguard inside B 2 Closure mudguard inside Carpet RIGHT side - serial Carpet LEFT side -serial Closing cap hole Ø Closing cap hole Ø = DON T USE IF THERE ARE THE LOADER TRACTOR.

21 AGRITAL s.r.l. Via L. Da Vinci, Arzago d Adda (BG) -ITALY- Tel fax = agrital@agrital.com