Manual and Remote Start Unit with Key Switch, 72x72 DIN Size
|
|
- Lawrence Nelson
- 6 years ago
- Views:
Transcription
1 Manual and Remote Start Unit with Key Switch, x DI Size FAILED TO ~~~ ~ ~ STOP 0 I Hz./ EAOM - 36 SPEED FAILURE CHARGIG FAIL Features Designed For Generator, Pump & Fire Pump Applications Remote start / stop capability with zero power consumption Engine start and stop Automatic shutdown on fault condition Provides alarm and status information Alarm and shutdown inputs Provides charge alternator excitation current Lamp test function Fail Monitoring Oil pressure Engine temperature Over speed & Under speed (generator application) Charging alternator Conf. Input- & Controls Engine fuel or stop solenoid Starter motor Preheat, external alarm horn or alarm out EAOM-36 Manual Start Unit use microprocessor based technology to provide integrated manual start and fault protection in a wide range of engine applications. The module is housed in x DI size.the module is used to start and stop the engine, indicating the operational status and fault conditions. Automatically shutting down the engine and indicating the engine failure by a flashing LED. User can control the engine via a two position key switch and pushbuttons mounted on the front panel or with remote input. The module has three application feature; 'Generator', 'Pump' or 'Fire Pump'. (can be selected from parameter P00). The module can connect directly with engine, thanks to high current relay outputs. The module has two feature for fuel. One of energize to run the other energize to stop. User can select the feature from program parameters. The module protect the engine against fault conditions. If a fault condition occurred, the module indicate the fault condition and shut-down the engine. If the key switch is OFF position the module has zero power consumption to save energy. The module energizes when the key switch position is getting O position. If Satart button is pressed, the Conf. Out relay output (if selected preheat output) will activate until the preheat delay is expired. Press Start button for starting the engine. When engine is running, module will stop the cranking. Also the module has remote start facility. Please select suitable type of remote start for your application from program parameters. If remote start input is active the module will start the engine. If remote start is passive the unit will stop the engine. The module will check the alarms aftersafety on timer is expired. Under one of this fault conditions the module will stop the engine; - Over speed (generator application), - Under speed(generator application), - High Temperature, - Low Oil Pressure, - Shutdown (if one of conf. input selected shutdown and activated). To reset the fault, turn the key switch to the OFF position for a few seconds. The Charge Failure is a warning alarm so the engine continue to work under this failure condition. Also this input supplying charge alternator excitation current. Shutdown the engine; If the engine fuel type is energize to stop, press Stop button until the engine comes to rest. After that select OFF position of the key switch. If the engine fuel type is energize to run, select OFF position of the key switch. Important note: On the Fire Pump application; If a fault condition occurred, the module will not stop the engine. The engine will be stopped only when the stop button was pressed or the remote stop signal was detected. Introduction Brochure. EG EAOM-36R 0 V00 05/09
2 Manual and Remote Start Unit with Key Switch, x DI Size Program Parameters for Generator Application Prog o Parameter ame Unit Limits Default P 00 Application Selection (Generator, Pump, Fire Pump) - GEn, PUP, FPU GEn P 0 P 0 P 03 Frequency Lower Limit Frequency Upper Limit ominal Alternator Frequency Hz. Hz. Hz P 04 ominal Speed Rpm P 05 Stop/Fuel Solenoid Selection - StoP - FUEL FUEL P 06 Stop Solenoid Energising Time Sec P 0 Crank Disconnect on Gen. Frequency Hz P 08 Crank Disconnect on Charge Alternator Voltage - dis - EnAb dis P 09 Crank Disconnect on Oil Pressure - dis - EnAb EnAb P 0 umber of Starting Attempts umber P Starting Attempt Duration Sec P Oil Pressure Bypass Time Sec P Safety On Delay Sec P 4 Frequency Fault Control Delay Sec P 5 Engine Running Time Value & ew Engine Running Time Hour P 6 Remote Start Selection: - 0= dis - dis 0 - Disable. The start / stop buton is used. (leave key switch position) - When the TERY applied to Rem. start input (terminal-), the engine start cranking. (leave key switch position) - When the TERY applied to input (terminal-3), the engine start cranking. (leave key switch position) P Conf. Out Type: 0 - Alarm Out - Horn Out Preheat Out P 8 Conf. Input - Only horn permanent, observation continuously - Engine stop, observation continuously P 9 Conf. Input P 0 - Only horn permanent, observation continuously - Engine stop, observation continuously Horn Duration - Sec = Cont P Password Program Parameters for Pump (Fire Pump) Applications Prog o Parameter ame Unit Limits Default P 00 Application Selection (Generator, Pump, Fire Pump) - GEn, PUP, FPU PUP P 05 Stop/Fuel Solenoid Selection - StoP - FUEL FUEL P 06 Stop Solenoid Energising Time Sec P 08 Crank Disconnect on Charge Alternator Voltage - dis - EnAb dis P 09 Crank Disconnect on Oil Pressure - dis - EnAb EnAb P 0 umber of Starting Attempts umber P Starting Attempt Duration Sec P Oil Pressure Bypass Time Sec P Safety On Delay Sec P 5 Engine Running Time Value & ew Engine Running Time Hour P 6 Remote Start Selection: - 0= dis - dis 0 - Disable. The start / stop buton is used. (leave key switch position) - When the TERY applied to Rem. start input (terminal-), the engine start cranking. (leave key switch position) - When the TERY applied to input (terminal-3), the engine start cranking. (leave key switch position) P Conf. Out Type 0 - Alarm Out - Horn Out Preheat Out P 8 Conf. Input - Only horn permanent, observation continuously - Engine stop, observation continuously P 9 Conf. Input - Only horn permanent, observation continuously - Engine stop, observation continuously P 0 Horn Duration Sec. 0= Cont P Password
3 Manual and Remote Start Unit with Key Switch, x DI Size Specifications Equipment Use Housing & Mounting Panel Cut-out Protection Weight Environmental Rating Operating / Storage Temperature Operating / Storage Humidity Installation Over Voltage Cat. Pollution Degree Mode of Operation EMC Electrical Safety Supply Voltage() Generator Speed Measurement Alternator Frequency Range Frequency Meas. Accuracy Cranking Dropouts Relay Outputs Failure Indicators Status Indicators Electrical control equipment for generating sets mm x mm x 5 mm 68 mm x 68 mm EMA4X (IP30 at front panel, IP0 at rear side) Approximately 0.5 kg Standard, indoor at an altitude of less then 000 meters with non-condensing humidity -5ºC to 0ºC / -40ºC to 85ºC 90% max. (on-condensing) II appliances, portable equipment II, ormal office or workplace, non-conductive pollution Continuous E , EMC generic emission standard for industrial equipment E , EMC generic immunity standard for industrial equipment E-600-, safety requirements for electrical equipment for measurement, control and laboratory use 8-3 V From generator voltage 5,6 to 99,9 Hz (5 to 300 VL-RMS) 0.5% Battery voltage can be 0V for max. 00msn during cranking (battery voltage should be at least nominal voltage before cranking) Start relay (0A@8V) Fuel relay (0A@8V) Conf. Out relay (0A@8V) Failed to engine start High engine temperature Low oil pressure Speed failure Battery charge failure General failure Hz./ Engine running time Engine start Engine stop 3
4 Manual and Remote Start Unit with Key Switch, x DI Size Dimensions & Front View EAOM - 36 Hz./ FAILED TO SPEED FAILURE ~~~ ~ ~ CHARGIG FAIL mm STOP 0 I Panel Cut-Out mm 5 mm 4 mm 68 mm TEA 68 mm EAOM-36.R Terminal Connections EAOM-36.RF Terminal Connections (Fail Safe) HIGH TEMP. LOW OIL PRES. () GE. D(W.L.) FUEL COF.O COF. IPUT- COF. IPUT- OR REMOTE (P6= => REM. IPUT) RS 3 GD TX RX GEERATOR VOLTAGE 300VAC (Ph-) Max. HIGH TEMP. LOW OIL PRES. () GE. D(W.L.) FUEL COF.O COF. IPUT- COF. IPUT- OR REMOTE (P6= => REM. IPUT) RS 3 GD TX RX GEERATOR VOLTAGE 300VAC (Ph-) Max. 4
5 GEERATOR GEERATOR Manual and Remote Start Unit with Key Switch, x DI Size Connection Schematic (Without Remote Start P6 = 0 (dis)) ALTERATOR COF.OUT FUSE- ER SOLEOID EGATIVE MUST BE GROUDED GE. D(W.L.) COF. IPUT- COF. IPUT- HOR FUSE- According to current required by solenoids (Max. 6A. T) Max. A. T - Connect the unit as shown in the appropriate diagram above. Be sure to connect the battery supply the right way round and - Use Alternator connection only generator application (P00 = Gen) Connection Schematic (With Remote Signal P6 = ) ALTERATOR COF.OUT FUSE- ER SOLEOID EGATIVE MUST BE GROUDED GE. D(W.L.) COF. IPUT- REMOTE SIGAL HOR FUSE- According to current required by solenoids (Max. 6A. T) Max. A. T - Connect the unit as shown in the appropriate diagram above. Be sure to connect the battery supply the right way round and - Use Alternator connection only generator application (P00 = Gen) 5
6 G EERATO R GEERATOR Manual and Remote Start Unit with Key Switch, x DI Size Connection Schematic (With Remote Start, o Power Consumption P6 = ) ALTERATOR REMOTE SWITCH FUSE- ER SOLEOID EGATIVE MUST BE GROUDED GE. D(W.L.) COF. IPUT- COF. IPUT- HOR COF.OUT FUSE- According to current required by solenoids (Max. 6A. T) Max. A. T - Connect the unit as shown in the appropriate diagram above. Be sure to connect the battery supply the right way round and - Use Alternator connection only generator application (P00 = Gen) Connection Schematic (For Fail Safe) ALTERATOR COF.OUT FUSE- ER SOLEOID EGATIVE MUST BE GROUDED GE. D(W.L.) COF. IPUT- COF. IPUT- HOR FUSE- According to current required by solenoids (Max. 6A. T) Max. A. T - Connect the unit as shown in the appropriate diagram above. Be sure to connect the battery supply the right way round and - Use Alternator connection only generator application (P00 = Gen) Product Codes EAOM-36.R Manual and Remote Start Unit with Key Switch, x DI Size, with relay outputs EAOM-36.RF Manual and Remote Start Unit with Key Switch, x DI Size, with relay outputs & fail safe inputs Emko Elektronik San. ve Tic. A.S. DOSAB Karanfil Sok. o:6 TR 6369 Bursa/TURKIYE Phone: Fax: emko@emkoelektronik.com.tr 6
Flight Systems. Replacement for KASSEC DESCRIPTION
DESCRIPTION The is a universal generator controller that will start, stop, and provide engine protection for most generators. Universal replacement for both the 90353 and 90354 KASSEC Compatible with most
More informationDEEP SEA ELECTRONICS PLC
DEEP SEA ELECTRONICS PLC 703 AUTOMATIC START MODULE OPERATING INSTRUCTIONS Author:- John Ruddock 703 Operating Instructions Issue Beta1 25/08/2003 2:45 PM JR - 1 - >
More information702 AUTOMATIC START MODULE OPERATING INSTRUCTIONS
702 AUTOMATIC START MODULE OPERATING INSTRUCTIONS > TABLE OF CONTENTS 1 DESCRIPTION OF OPERATION... 4 1.1 MANUAL MODE OPERATION... 4 1.2 AUTOMATIC MODE OF OPERATION...
More informationDEEP SEA ELECTRONICS PLC
COMPLEX SOLUTIONS MADE SIMPLE DEEP SEA ELECTRONICS PLC DSE704 AUTOSTART CONTROL MODULE OPERATING MANUAL 057-042 704 Operating Instructions Issue 2.1 18/06/2007 11:27:00 JR - 1 - Deep Sea Electronics Plc
More informationDKG-114 MANUAL AND REMOTE START UNIT
DKG-114 MANUAL AND REMOTE START UNIT FEATURES Both manual and remote controlled engine starting and stopping, Automatic shutdown on fault condition, Optional cooldown cycle on remote start operation, Optional
More informationDEEP SEA ELECTRONICS PLC
COMPLEX SOLUTIONS MADE SIMPLE. DEEP SEA ELECTRONICS PLC DSE710 AUTOSTART CONTROL MODULE OPERATING MANUAL Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel: +44
More informationEnergy Division
Energy Division http://energy.tycoelectronics.com Installation and Operating Manual GEN-TRANS Automatic Generator Transfer Switch Controller with Metering Tyco Electronics UK Limited Crompton Instruments
More informationDEEP SEA ELECTRONICS PLC
COMPLEX SOLUTIONS MADE SIMPLE DEEP SEA ELECTRONICS PLC DSE720 AUTOSTART CONTROL MODULE OPERATING MANUAL http://bestgenerator.spb.ru/?page_id=6765 Deep Sea Electronics Plc Highfield House Hunmanby North
More informationEAOM-10.2 AUTOMATIC TRANSFER SWITCH & START UNIT FOR DIESEL GENERATORS
AUTOMATIC TRANSFER SWITCH & START UNIT FOR DIESEL GENERATORS Designed for diesel generators Long life membrane front key pad EEPROM internal memory 1 GENERAL INFORMATION EAOM-102 Automatic Transfer Unit
More informationMODEL 520 REMOTE START ENGINE MANAGEMENT SYSTEM
MODEL 520 REMOTE START ENGINE MANAGEMENT SYSTEM DSE 520 ISSUE 4 4/4/02 MR 1 TABLE OF CONTENTS Section Page INTRODUCTION... 4 CLARIFICATION OF NOTATION USED WITHIN THIS PUBLICATION.... 4 1. OPERATION...
More informationHGM7100N SERIES (HGM7110N/7120N) GENSET CONTROLLER USER MANUAL
HGM7100N SERIES (HGM7110N/7120N) GENSET CONTROLLER USER MANUAL SMARTGEN (ZHENGZHOU) TECHNOLOGY CO., LTD. Chinese trademark English trademark SmartGen make your generator smart SmartGen Technology Co.,
More informationHGM1770 Automatic Generator Control Module OPERATING MANUAL Smartgen Electronic
HGM1770 Automatic Generator Control Module OPERATING MANUAL Smartgen Electronic CONTENT 1. SUMMARY... 4 2. PERFORMANCE AND CHARACTERISTICS... 4 3. SPECIFICATIONS... 5 4. OPERATION... 6 5. PROTECTION...
More informationHGM72 Automatic Generator Module OPERATING MANUAL Smartgen Electronic
HGM72 Automatic Generator Module OPERATING MANUAL Smartgen Electronic CONTENT 1 SUMMARY... 4 2 FEATURES... 4 3 SPECIFICATION... 4 4 DISPLAY SYMBOL AND OPERATION... 5 5 ALARM... 7 6 PARAMETERS TABLE (ONLY
More informationHGM1780 AUTOMATIC GENERATOR MODULE CONTENT 1. SUMMARY PERFORMANCE AND CHARACTERISTICS SPECIFICATION OPERATION...
CONTENT 1. SUMMARY...4 2. PERFORMANCE AND CHARACTERISTICS...4 3. SPECIFICATION...5 4. OPERATION...6 4.1. DISPLAY PANEL...6 4.2. LCD ICON INSTRUCTION...7 4.3. DISPLAY INSTRUCTIONS...7 4.4. DISPLAY DESCRIPTION...8
More informationGENSET CONTROL MODULE A121H / A241H. User selectable time delays for engine start and engine stop (cool down).
Technical Data Sheet GENSET CONTROL MODULE A121H / A241H Features: Models for both 12V and 24V systems. One model for both spark ignition and diesel engines. 4-alarm light outputs with lamp-test provisions.
More informationAuto Mains Failure AMF Controller AE10113
Auto Mains Failure AMF Controller AE03 Auto Mains Failure DESCRIPTION AMF Controller AE03 is an Automatic Mains Failure controller, which activates the generator during power failure & vice versa. The
More informationSpecification. Terminals Detail. AUTO (Remote Start) Operation. TEST Operation. OFF Operation
Specification ITM SRIPTION Supply 9.0 to 35 V lternator Input Range 5 ~ 300V lternator Input Frequency 50/60 Hz MPU Signal Input Range ± 2V to 70V Peak Rated MPU Frequency 100 Hz ~ 10,000 Hz Operating
More informationDeep Sea Electronics Plc
Deep Sea Electronics Plc 5120 AUTOMATIC MAINS FAILURE MODULE OPERATING MANUAL Author: Anthony Manton Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH England Tel: +44 (0) 1723
More informationGENSET CONTROL MODULE LEVEL 0 A120A. User selectable time delays for engine start and engine stop (cool down).
Technical Data Sheet GENSET CONTROL MODULE LEVEL 0 A120A Features: One model for both spark ignition and diesel engines. 4-alarm light outputs with automatic lamp-test provision. Overspeed adjustment not
More informationHGM1780. Automatic Genset Controller USER MANUAL. Smartgen Technology
HGM1780 Automatic Genset Controller USER MANUAL Smartgen Technology Smartgen Technology Co., Ltd No. 28 Jinsuo Road Zhengzhou Henan Province P. R. China Tel: 0086-371-67988888/67981888 0086-371-67991553/67992951
More informationDEEP SEA ELECTRONICS PLC
COMPLEX SOLUTIONS MADE SIMPLE. DEEP SEA ELECTRONICS PLC DSE4120 AUTO MAINS FAILURE MODULE OPERATING MANUAL Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel:
More informationHGM72 Automatic Generator Module OPERATING MANUAL Smartgen Electronic
HGM72 Automatic Generator Module OPERATING MANUAL Smartgen Electronic Smartgen Electronic Equipment Co., Ltd No.28 Jinsuo Road Zhengzhou Henan Province P.R.China Tel: 0086-371-67988888/67981888 0086-371-67991553/67992951/67992952
More informationHGM501 Gen-set Controller USER MANUAL. Smartgen Technology
HGM501 Gen-set Controller USER MANUAL Smartgen Technology Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. OVERVIEW... 4 PERFORMANCE AND CHARACTERISTICS... 4 TECHNICAL DATA... 5 OPERATION... 6 4.1. BUTTON DESCRIPTION...
More informationGENSET CONTROL MODULE A121A / A241A
Technical Data Sheet GENSET CONTROL MODULE A121A / A241A Features: Models for both 12V and 24V systems. One model for both spark ignition and diesel engines. 4-alarm light outputs with lamp-test provisions.
More informationDEEP SEA ELECTRONICS PLC
COMPLEX SOLUTIONS MADE SIMPLE. DEEP SEA ELECTRONICS PLC DSE5110 AUTOSTART CONTROL MODULE OPERATING MANUAL Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel: +44
More informationHSC940 Genset Controller CONTENTS 1 OVERVIEW PERFORMANCE AND CHARACTERISTICS SPECIFICATION OPERATION KEY FUNCTIONS...
CONTENTS 1 OVERVIEW... 4 2 PERFORMANCE AND CHARACTERISTICS... 5 3 SPECIFICATION... 7 4 OPERATION... 8 4.1 KEY FUNCTIONS... 8 4.2 INDICATOR LIGHT... 9 4.3 AUTO START/STOP OPERATION... 10 4.4 MANUAL START/STOP
More informationDKG-317 MANUAL AND REMOTE START UNIT
Tel: +54-11-4629-600 Fax:+54-11-4627-3500 http://www.cramelectro.com DKG-317 MANUAL AND REMOTE START UNIT FEATURES Manual starting and stopping Engine control Generator protection Built in alarms and warnings
More informationENGINE PROTECTION BOARD PDM1
ENGINE PROTECTION BOARD REFERENCE MANUAL. Standard of reference: IEC/EN 60255-6 IEC/EN 61000-4-2 IEC/EN 61000-4-3 IEC/EN 61000-4-4, IEC/EN 61000-4-5 IEC/EN 61000-4-6 IEC/EN 55011 IEC/EN 60028-2-61 IEC/EN
More informationGenerator Controller Manual
Generator Controller Manual Web Site:http://www.monicon.com.tw E-mail:sales@monicon.com.tw 1. Controller Description is low cost but multi-function diesel engine generator controller. It applies with 3
More informationGCU-10. Automatic Engine Control Unit Operators Manual
GCU-10 Automatic Engine Control Unit Operators Manual KUTAI ELECTRONICS INDUSTRY CO., LTD. TEL : +886-7-8121771 FAX : +886-7-8121775 Website : www.kutai.com.tw Headquarters : No.3, Lane 201, Chien Fu St.,
More informationGENSET CONTROL MODULE LEVEL 1 A121CM / A241CM. Special logic to re-establish cranking following a false start.
Technical Data Sheet GENSET CONTROL MODULE LEVEL 1 A121CM / A241CM Features: Models for both 12V and 24V systems. One model for both spark ignition and diesel engines. 5-alarm light outputs with lamp-test
More informationHGM1750 Genset Security Module USER MANUAL Smartgen Technology
HGM1750 Genset Security Module USER MANUAL Smartgen Technology CONTENT 1. SUMMARY... 4 2. PERFORMANCE AND CHARACTERISTICS... 5 3. SPECIFICATION... 7 4. OPERATION... 8 5. PROTECTION... 9 6. PARAMETER RANGE
More informationCascade CD101 Auto-Start Controller. Installation and Operations Manual Sections 40 & 75
Cascade CD101 Auto-Start Controller Installation and Operations Manual 00-02-0594 2018-02-15 Sections 40 & 75 In order to consistently bring you the highest quality, full featured products, we reserve
More informationAUTOSTART 705S V1.00 AUTOSTART 710S / 720S / 730S V1.04 Programming Reference and Check Sheets
The Generator Controls Division of Frank W. Murphy AUTOSTART 705S V1.00 AUTOSTART 710S / 720S / 730S V1.04 Programming Reference and Check Sheets MODEX AUTOMATION FRANK W. MURPHY LTD. Church Road Laverstock
More informationPSM72H Push-Button Start Module
Capricorn Controls DA02PSM72H1-2 Data & Application Note Page 1 of 6 PSM72H Push-Button Start Module Genset Controls - Timers/Monitors/Trips - Battery Charging Spares & Accessories - Custom Products Ultra
More informationHGM6000K Series Automatic Generator Module OPERATING MANUAL Smartgen Electronic
HGM6000K Series Automatic Generator Module OPERATING MANUAL Smartgen Electronic CONTENT 1 SUMMARY... 4 2 PERFORMANCE AND CHARACTERISTICS... 4 3 SPECIFICATION... 6 4 OPERATION... 6 4.1 KEY FUNCTION... 6
More informationDSEULTRA DSE6000 Quick Start Guide Document Number
n DSEULTRA DSE6000 Quick Start Guide Document Number 057-102 Author : John Ruddock Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel: +44 (0) 1723 890099 Sales
More informationTe 803 Electronic Controller. Service, Operation & Technical Information Manual
Te 803 Electronic Controller Service, Operation & Technical Information Manual WARNING! Technical descriptions and data given in this document are accurate, to the best of our knowledge, but can be subject
More informationHGM6410/6420. Automatic Generator Module. With J1939 Interface OPERATING MANUAL. Smartgen Electronics
HGM6410/6420 Automatic Generator Module With J1939 Interface OPERATING MANUAL Smartgen Electronics Smartgen Electronic Equipment Co,.Ltd No.12 Dongqing Street Zhengzhou Henan Province P.R.China Tel : (0086)-371-67992951
More informationDKG-207 AUTOMATIC MAINS FAILURE AND REMOTE START UNIT
DKG-207 AUTOMATIC MAINS FAILURE AND REMOTE START UNIT FEATURES Automatic mains failure, Engine control, Gas engine support, Generator protection, Built in alarms and warnings, 3 phase mains voltage inputs
More informationOPERATING INSTRUCTIONS MCP-MT1
OPERATING INSTRUCTIONS MCP-MT1 MRM PROCOM Pvt Ltd ISO-9001-2008 certified organization Plot No. : 20-21, Industrial Estate, Sector - 59, Phase-II, Faridabad (Haryana) Ph.: 0129-4700400(10 Lines) Email:
More informationTRANS-MIDIAMF AUTOMATIC MAINS FAILURE UNIT
TRANS-MIDIAMF AUTOMATIC MAINS FAILURE UNIT 1. Introduction 1.1 General Specifications The unit provides for automatic transfer of a load from mains to generator in the event of a mains failure. Intended
More informationENGEN -100/ENGEN -200 ENGINE GENERATOR CONTROLLER
ENGEN -100/ENGEN -200 ENGINE GENERATOR CONTROLLER The engine/generator controller is an integrated genset controller contained in a single, easy to install package. The controller contains a microprocessor-based
More informationDKG-215 MANUAL AND REMOTE START UNIT
DKG-215 MANUAL AND REMOTE START UNIT FEATURES Manual and remote starting and stopping Zero power consumption at rest Engine control mode available Generator protection Built in alarms and warnings 1 phase
More informationRVS-DN Digital Reduced Voltage Motor Starter
RVS-DN Digital Reduced Voltage Motor Starter Specification Guide Specification Guide Contents 1.0 Introduction 2.0 Specifications 2.1 Standard Performance Features 2.2 Standard Protection Features 2.3
More informationHGM6320T AUTOMATIC GENERATOR CONTROLLER USER MANUAL
HGM6320T AUTOMATIC GENERATOR CONTROLLER USER MANUAL Smartgen Technology CONTENT 1 SUMMARY... 4 2 PERFORMANCE AND CHARACTERISTICS... 4 3 SPECIFICATION... 5 4 OPERATION... 6 4.1 LCD DISPLAY... 6 4.2 KEY
More informationUSER MANUAL ZHENGZHOU SMARTGEN TECHNOLOGY CO.,LTD
HGM400 Series Genset Controller (HGM410/HGM420) USER MANUAL ZHENGZHOU SMARTGEN TECHNOLOGY CO.,LTD CONTENTS 1 OVERVIEW... 5 2 PERFORMANCE AND CHARACTERISTICS... 6 3 SPECIFICATION... 8 4 OPERATION... 9 4.1
More informationTRANS-MINIAUTO+ AUTOMATIC START UNIT FOR GAS/DIESEL/GASOLINE GENERATORS WITH J1939 ECUs User Manual
TRANS-MINI+ MATIC START UNIT FOR GAS/DIESEL/GASOLINE GENERATORS WITH J1939 ECUs User Manual EMKO ELEKTRONÝK A. Þ. Demirta þ Org. San. Bolg. Karanfil Sk. No: 6 TR 16369 Bursa / TURKEY Phone Faks Url E-mail
More informationHGM6100K Series Automatic Generator Module OPERATING MANUAL Smartgen Electronics
HGM6100K Series Automatic Generator Module OPERATING MANUAL Smartgen Electronics All rights reserved. No part of this publication may be reproduced in any material form (including photocopying or storing
More informationRVS-DX Digital Reduced Voltage Motor Starter
RVS-DX Digital Reduced Voltage Motor Starter Specification Guide Specification Guide Contents 1.0 Introduction 2.0 Specifications 2.1 Standard Performance Features 2.2 Standard Protection Features 2.3
More informationHGM6320T AUTOMATIC GENERATOR CONTROLLER USER MANUAL
HGM6320T AUTOMATIC GENERATOR CONTROLLER USER MANUAL Smartgen Technology Smartgen Technology Co., Ltd No. 28 Jinsuo Road Zhengzhou Henan Province P. R. China Tel: 0086-371-67988888/67981888 0086-371-67991553/67992951/67992952
More informationHGM6310D/6320D AUTOMATIC GENERATOR MODULE USER MANUAL
HGM6310D/6320D AUTOMATIC GENERATOR MODULE USER MANUAL SMARTGEN ELECTRONIC CONTENT 1 SUMMARY... 4 2 PERFORMANCE AND CHARACTERISTICS... 4 3 SPECIFICATION... 6 4 OPERATION... 7 4.1 KEY FUNCTION... 7 4.2 AUTOMATIC
More informationModel H30 Operation Manual
Model H30 Operation Manual Model H30 Version 1.0 August 1, 2007 2 135 West Davenport Street Rhinelander WI 54501 Phone: 866.441.7997 Fax: 866.278.0036 info@houstonst.com www.houstonst.com 3 Table of Contents
More informationCat/DCG-6D1I/07-08/03/Ver 1 Page 2/10
Cat/DCG-6D1I/07-08/03/Ver 1 Page 2/10 Index 1.1 Introduction 1.2 Salient Feature of the DGC-6D 1.2.1 Protection & Supervision 1.2.2 Measurement & Display 1.2.3 LED Indications 1.2.4 Timer 1.3 Function
More information5220 AUTOMATIC MAINS FAILURE MODULE OPERATING MANUAL
5220 AUTOMATIC MAINS FAILURE MODULE OPERATING MANUAL > Section DSE Model 5220 Automatic Mains Failure & Instrumentation System Operators Manual TABLE OF CONTENTS
More informationTRANS-AMF AUTOMATIC MAINS FAILURE UNIT FOR GAS/DIESEL/GASOLINE GENERATORS WITH J1939 ECUs User Manual
TRANS-AMF AUTOMATIC MAINS FAILURE UNIT FOR GAS/DIESEL/GASOLINE GENERATORS WITH J1939 ECUs User Manual EMKO ELEKTRONÝK A. Þ. Demirta þ Org. San. Bolg. Karanfil Sk. No: 6 TR 16369 Bursa / TURKEY Phone Faks
More informationStarting System DS-102 Series 200. Elmatik AS P.O.Box 309 NO-3471, Slemmestad T F
Starting System DS-102 Series 200 Elmatik AS P.O.Box 309 NO-3471, Slemmestad T - +47 31 28 37 83 F - +47 31 28 37 93 www.elmatik.no post@elmatik.no CONTENT 1. INTRODUCTION 3 2. TECHNICAL SPECIFICATIONS
More informationDesigned for ease of integration with automation systems
BAS, 200 ~ 600V, 1/2-30HP BUILDING AUTOMATION STARTER SMARTER AND MORE VERSATILE THAN EVER Smartstart Equipped with advanced I/O including Fireman s Override and damper control, the BAS was designed from
More informationQuick Start Guide TS 910
Quick Start Guide TS 910 DANGER HAZARD OF ELECTRICAL SHOCK, EXPLOSION, OR ARC FLASH Read and understand this quick start guide before installing and operating the transfer switch The installer is responsible
More informationMD10. Engine Controller. Installation and User Manual for the MD10 Engine Controller. Full Version
MD10 Engine Controller Installation and User Manual for the MD10 Engine Controller. Full Version File: MartinMD10rev1.4.doc May 16, 2002 2 READ MANUAL BEFORE INSTALLING UNIT Receipt of shipment and warranty
More informationInteliCharger V 20A Intelligent Automatic Battery Charger
InteliCharger InteliCharger 500 24V 20A Intelligent Automatic Battery Charger September 2012 Reference Guide TABLE OF CONTENTS 1 Document information... 2 2 EQUIPMENT RATING... 3 3 ENVIRONMENT... 3 4 PROTECTION...
More informationOPERATING INSTRUCTION: DGC-6D/6D1I
OPERATING INSTRUCTION: DGC-6D/6D1I GCB Auto Man Stop Fail - PROCOM Pvt Ltd MRM PROCOM Plot No. : 20-21, Industrial Estate, Sector - 59, Phase-II, Faridabad (Haryana) Ph.: 0129-4700400(10 Lines) Email:
More informationObserve all necessary safety precautions when controlling the soft starter remotely. Alert personnel that machinery may start without warning.
Introduction OPERATING INSTRUCTIONS: MCD REMOTE OPERATOR Order Codes: 175G94 (for MCD 2) 175G361 + 175G9 (for MCD 5) 175G361 (for MCD 3) 1. Introduction 1.1. Important User Information Observe all necessary
More informationTransfer switch GTEC open or delayed transition
Transfer switch GTEC open or delayed transition 40-1250 Amp Description The GTEC automatic transfer switch combines reliability and flexibility in a small, economical package for transferring loads between
More informationDKG-109 AUTOMATIC MAINS FAILURE UNIT
Tel: +90-216-466 84 60 Fax: +90-216 364 65 65 datakom@datakom.com.tr http://www.datakom.com.tr DKG-109 AUTOMATIC MAINS FAILURE UNIT FEATURES Automatic mains failure Engine control Generator protection
More informationECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual
ECU-02 Ver2.1 Automatic Engine Control Unit Operators Manual Headquarters : No.3, Lane 201, Chien Fu St., Chyan Jenn Dist., Kaohsiung, TAIWAN Tel : + 886-7-8121771 Fax : + 886-7-8121775 URL : http://www.kutai.com.tw
More informationBE22 OEM's Manual V1.3x December 2007 page 1
BE22 OEM's Manual V1.3x December 2007 page 1 BE22 OEM s Manual The information in this document is subject to change without notice. No part of this document may be copied or reproduced in any form or
More informationOPERATING INSTRUCTIONS ECON-M
OPERATING INSTRUCTIONS ECON-M INDEX 1.0 Introduction 2.0 Salient features, Protection & Supervision 3.0 Display/ Front Panel 4.0 Switches Description 5.0 LED Annunciations Description 6.0 Lamp Test 7.0
More informationDKG-509 AUTOMATIC MAINS FAILURE UNIT
DKG-509 AUTOMATIC MAINS FAILURE UNIT CANBUS AND MPU VERSIONS DESCRIPTION The controller is a comprehensive AMF unit for single genset standby or dual genset mutual standby operations. The unit is available
More informationHGM6000K Series Automatic Generator Module USER MANUAL Smartgen Technology
HGM6000K Series Automatic Generator Module USER MANUAL Smartgen Technology Chinese trademark English trademark Smartgen make your generator smart Smartgen Technology Co., Ltd. No. 28 Jinsuo Road Zhengzhou
More informationPowerCommand 2100 digital generator set control
Specification sheet PowerCommand 2100 digital generator set control Description The PowerCommand 2100 control is a microprocessor-based generator set monitoring, metering and control system. The control
More informationDeep Sea Electronics Plc
Deep Sea Electronics Plc 550 Operators Manual Author Miles Revell Deep Sea Electronics Plc Highfield House Hunmanby Industrial Estate North Yorkshire YO14 0PH ENGLAND Tel +44 (0) 1723 890099 Fax +44 (0)
More informationHGM6400 Automatic Genset Controller (With J1939 Interface) USER MANUAL Smartgen Technology
HGM6400 Automatic Genset Controller (With J1939 Interface) USER MANUAL Smartgen Technology Chinese trademark English trademark Smartgen make your generator smart Smartgen Technology Co., Ltd No. 28 Jinsuo
More informationHGM9510 GENSET PARALLEL (WITH GENSET) UNIT USER MANUAL
HGM9510 GENSET PARALLEL (WITH GENSET) UNIT USER MANUAL SMARTGEN (ZHENGZHOU) TECHNOLOGY CO.,LTD. Chinese trademark English trademark SmartGen make your generator smart SmartGen Technology Co., Ltd. No.
More informationDKG-109J AUTOMATIC MAINS FAILURE UNIT
DKG-109J AUTOMATIC MAINS FAILURE UNIT CANBUS VERSION FEATURES True RMS measurements Automatic mains failure ECU control and monitoring through J1939 CAN J1939 ECU warnings displayed as text Various engine
More informationDeep Sea Electronics Plc
Deep Sea Electronics Plc 5520 Operators Manual Author Tony Manton Deep Sea Electronics Plc Highfield House Hunmanby Industrial Estate North Yorkshire YO14 0PH ENGLAND Tel +44 (0) 1723 890099 Fax +44 (0)
More informationUSERS MANUAL MCD REMOTE OPERATOR
USERS MANUAL MCD REMOTE OPERATOR Order Code: 175G9004, 175G3061 Contents Contents Introduction...2 Important User Information...2 General Description...2 Symbols Used in this Manual...2 Installation...3
More informationICON 2 1. FEATURES AND CHARACTEIRICS
ICON 2 1. FEATURES AND CHARACTEIRICS High end Micro-controller(DSP) technology Wide range of auxiliary supply: 7V to 45Vdc. Low power Consumption : 200 ma @ 12 V DC. Alphanumeric 16X4 or 16X2 LCD display
More informationQuick Start Guide TS 910 & TS 920
Quick Start Guide TS 910 & TS 920 DANGER HAZARD OF ELECTRICAL SHOCK, EXPLOSION, OR ARC FLASH Read and understand this quick start guide before installing and operating the transfer switch The installer
More informationREVISED ATM72 Auto Transfer Module
Capricorn Controls DA01ATM1-1 Data & Application Note Page 1 of 8 REVISED - - - ATM72 Auto Transfer Module Genset Controls - Timers - Monitors - Trips - Battery Charging - Spares & Accessories - Custom
More informationGENSET CONTROL MODULE
HGM7200/HGM7100 Series AUTOMATIC GENSET CONTROL MODULE User Manual SMARTGEN TECHNOLOGY Smartgen Technology Co., Ltd No.28 Jinsuo Road Zhengzhou Henan Province P. R. China Tel: 0086-371-67988888/67981888
More informationKCR1. Kiln Controller Handbook. Kilncare Ltd. The Kiln Works 907 Leek New Road Baddeley Green Stoke-on-Trent Staffordshire, ST2 7HQ United Kingdom
KCR1 Kiln Controller Handbook Issue: a b Date: 04Sep2008 05Sep2008 Kilncare Ltd. The Kiln Works 907 Leek New Road Baddeley Green Stoke-on-Trent Staffordshire, ST2 7HQ United Kingdom Tel: 01782 535915 Tel:
More informationBe-K3 OEM s Manual --
Be-K3 OEM's Manual V200 - July - 010 page 1 Be-K3 OEM s Manual -- Consult Section 17.0 for software upgrades & revisions The information in this document may be subject to change without notice. No part
More informationDC POWER SUPPLY SYSTEMS
DC POWER SUPPLY SYSTEMS double branch Rectifier - SCR type TITANIUM 2R-SCR PLUS SERIES TITANIUM 2R-SCR rectifier series belongs to the Double Branch category thus provided with two independent AC / DC
More informationUSER MANUAL FOR GC500 GENSET CONTROLLER SEDEMAC ABSTRACT
ABSTRACT This manual is intended as an information guide for operating SEDEMAC's GC500 genset controller. USER MANUAL FOR Doc #SED-MAN-GC500-002 Date: 01-Aug-2016 GC500 GENSET CONTROLLER Product Manual
More informationThree-Phase Soft Starters
Submittal Data English Language/IP Units 04/14 Contact Information: Hyper Engineering, Pty. Ltd. 4 / 14 Ralph Black Dr Wollongong Nth, NSW 2500 AUSTRALIA www.hypereng.com sales@hypereng.com (+61) 2 4229
More informationMotor Controllers AC Semiconductor Motor Controller Type RSHP Flexy
otor Controllers AC Semiconductor otor Controller Type RSHP Flexy Soft starting and stopping of 3-phase squirrel cage motors Low surge and vibration-free starting User-selected ramping profiles Integral
More informationTRANS-MINIAUTO AUTOMATIC START UNIT FOR GAS/DIESEL/GASOLINE GENERATORS WITH J1939 ECUs User Manual
TRANS-MINI MATIC START UNIT FOR GAS/DIESEL/GASOLINE GENERATORS WITH J1939 ECUs User Manual TEL (057) 4345183 MÓVIL (057) 3112120386 BOGOTÁ COLOMBIA Correo: info@sapaip.com Página Web: www.sapaip.com Introduction
More informationDiesel generator set C17D5T series
Specification sheet Diesel generator set C17D5T series 17 @ 50 Hz Description This Cummins commercial generator set is a fully integrated power generation system, providing optimum performance, reliability,
More informationDEEP SEA ELECTRONICS PLC
COMPLEX SOLUTIONS MADE SIMPLE. DEEP SEA ELECTRONICS PLC DSE5220 AUTO MAINS FAILURE MODULE OPERATING MANUAL Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel:
More information60 Series Engine Controls
ECU 60 Series Engine Controls Use CAUTION since you are applying 120VAC RMS to the AC Input terminals and that it is always potentially their during engine run!!! ECU is a registered trademark of Engineering
More informationStandard Features 200-600V, 50/60Hz input power supply Built-in run rated (AC1) By-pass contactor up to 820 A * Rated 450% current Conformal coated circuit board Voltage ramp or current limit start modes
More informationCURTIS TOLEDO. AF Series Compressors VS models with VFD WARNING
AUGUST, 2004 REV.A CURTIS TOLEDO OPERATOR S MANUAL SUPPLEMENT AF Series Compressors VS models with VFD WARNING Personal injury and/or equipment damage will result by failing to pay attention to the vital
More informationTransfer switch OTEC open or delayed transition
Transfer switch OTEC open or delayed transition 40-1000 Amp Description OTEC transfer switches are designed for operation and switching of electrical loads between primary power and standby generator sets.
More informationAxpert-CSS AMTECH DRIVES Axpert-CSS Amtech
The Axpert-CSS is a range of Combination Soft Starter panels offered by AMTECH DRIVES. We also offer the module unit as an individual product, named as Axpert-Opti torque Soft Starter. This is only the
More informationXCITE Owner s Manual. Reso-not TM Damping System XCITE 1502C HYDRAULIC POWER SUPPLY
Reso-not TM Damping System XCITE Owner s Manual 1502C HYDRAULIC POWER SUPPLY Xcite Systems Corporation 675 Cincinnati RDS Batavia - 1 Pike Cincinnati, Ohio 45245 Tel: (239) 980-9093 Fax: (239) 985-0074
More informationHGM9520 Genset Parallel (With Mains) Unit USER MANUAL. Smartgen Technology
USER MANUAL Smartgen Technology Chinese trademark English trademark Smartgen make your generator smart Smartgen Technology Co., Ltd. No. 28 Jinsuo Road Zhengzhou city Henan Province P. R. China Tel: +86-371-67988888/67981888
More informationOTEC Transfer switch open transition
Specification sheet OTEC Transfer switch open transition 40 1200 amp Description OTEC transfer switches are designed for operation and switching of electrical loads between primary power and Standby generator
More information1. AC VOLTS: Displays generator output in voltage. 2. AC FREQUENCY: Displays the speed of the generator set in Hertz.
1. AC VOLTS: Displays generator output in voltage. 2. AC FREQUENCY: Displays the speed of the generator set in Hertz. 3. AMMETER/PERCENT OF LOAD: Displays the load on the generator in amps or in percentage.
More informationBE24 OEM s Manual -V1.26X
BE24 OEM's Manual V1.26X- 24-October-05 page 1 BE24 OEM s Manual -V1.26X The information in this document is subject to change without notice. No part of this document may be copied or reproduced in any
More information