floodlighting - index

Transcription

1

2 floodlighting - index AM5000 A versatile range of floodlights available with 3 beam distributions, including a flat glass version with a beam emergence of 60 Suitable for all general purpose exterior floodlighting applications. AL5310 An attractive range of small low cost floodlights with six beam distributions. Ideal for façade, architectural, area floodlighting and security lighting. Lamps up to 150W SON-TD or MBI. Lamps up to 400W MBI; 400W SON-T. AM5011/12 ONLY Page 4.4 Page 4.9 AL5100 A double asymmetric distribution floodlight range designed for general purpose use. Lamps up to 400W SON-T or MBI. AL5400 A range of double asymmetric distribution floodlights, specially designed to provide efficient lighting of large open areas, airports, docks, motorway intersections and industrial complexes. Lamps up to 2 x 400W MBI; 2 x 400W SONP-T; 1 x 1000W MBI; 1 x 1000W SONP-T. Page 4.6 Page 4.10 AL5210 A versatile double asymmetric beam floodlight offering low light pollution control. Ideally suited to the lighting of multi-use sports areas, tennis courts and general exterior applications. Lamps up to 1000W SON-T; 1000W MBI. AL5 Floodlight for use with HID lamps up to 2000W. Suitable for lighting sports fields, dock yards, marshalling yards and most large area lighting applications. Lamps up to 2000W SON-T; 2000W HQI Page 4.7 Page

3 AL5700 Challenger 1 A double asymmetric distribution floodlight range, specially designed for lighting outdoor sports grounds, smaller sports stadiums and large open areas where light pollution control is an essential requirement. Lamps up to W SON-T, 1000W SON-TD, 2000W MHN-TD GUIDE TO LOGOS The following logos are provided to assist the customer towards making an informal decision over the specification of the luminaire. SECURITY Luminaires denoted with this logo are ideally suited to security applications. ULOR Floodlights; the % of upward light produced is given at the specific elevation stated and is the maximum working elevation that the floodlight would be set to in normal practice. AL5800 Challenger 2 An asymmetric distribution floodlight range used primarily for side lighting sports systems including roof mounting in stadiums. Lamps up to 2000W HQI; 2000W MHD. Page 4.14 ABACUS LIGHT CONTROL SYSTEM Floodlight ranges that are denoted with this logo possess specific design characteristics that effectively control the three key forms of obtrusive light, these being upward light, overspill and glare. IP RATING The IP rating indicates the level of protection against ingress of moisture or dust and is defined by 2 digits. The first digit relates to dust protection, the second digit relates to water protection. Page 4.18 AL5900 Challenger 3 A symmetrical distribution floodlight range, specially designed for lighting large sports stadia using corner mast systems. Of high performance and compact design, these floodlights provide precision optical control coupled with reduced weight and windage compared to conventional stadium floodlighting. Lamps up to 2000W HQI; 2000W MHD. National Inspection Council for Electrical Installation Contracting Page 4.20 APPROVED CONTRACTOR 4.2

4 floodlighting - ordering details When ordering floodlights the following information will enable us to identify the product you require both quickly and accurately. By using our reference numbering system, errors can be avoided ensuring that the right products are delivered to the correct address. 1 Your company name, contact name and telephone number. 2 Your order number. 3 Invoice address. 4 Delivery address (if different to above) and, if notification of delivery is required in advance, contact name and telephone number. 5 Quantity of floodlights required. 6 Floodlight reference number made up as the example below. 7 Supply voltage and frequency. 8 Abacus floodlights are supplied in either integral or remote control gear versions. For floodlights supplied with remote control gear this can be provided either as loose components or pre-wired on gear trays (extra cost). Please specify which is required. 9 Most floodlights are provided with non cut-out ignitors and standard ballasts. Ballasts protected with internal thermal overload switches and ignitors with cut-out facility are available at extra cost. Please specify which is required. AM ST *Basic Model Number *Lamp Wattage *Lamp Type THD SE ST SPT STD CMD MU MI MIF MIL HQI TUNGSTEN HALOGEN SON-E SON-T SON P-T SON T-D CMD-TD MBF-U MBI MBIF MBIL HQI-TS2000 WDS HQI-TS1000 WDS MHN/LA MHN/SA HQI/NL MHN-LA-2000 MHN-SA-2000 HQI-TS2000WNL *Please refer to product pages which show details of choices available. 4.3

5 floodlighting - AM5000 series AM5011/12 AM5006/8 AM5009/5010 A versatile range of floodlights available in 3 beam distributions for use with high pressure discharge lamps up to 400W. Suitable for use in all general purpose exterior lighting applications. Featuring: High pressure die-cast aluminium body and front cover frame, finished light grey (RAL 7032) polyester powder coating. Accessories available: - Cowl AM9007 for reduced light pollution. - Front guard AM Vertical louvres AM9006 (0.77kg). - Polycarbonate front shield AM9040 N.B: Accessories only allow single fitting to each floodlight. Electropolished, anodised and sealed aluminium reflector. E-40 lamp holder with adjustable assembly for centralising the lamp within the floodlight. Toughened front glass Galvanised steel stirrup with protractor for setting elevation angle. Access to lamps and control gear via opening the hinged front cover. Integral gear versions incorporate a galvanised steel control gear tray that is removable for ease of maintenance. Versions AM5009/10, AM5006/8 include a baffle above the lamp to reduce glare and improve performance. AM5011/12 Versions AM5011/12 are Flat Glass with a beam emergence of +60 for low light pollution applications. 4.4

6 floodlighting - AM5000 series AM5000 series floodlights are available in 3 beam distributions:- The large range of beam options allows complete versatility of application from lighting areas to floodlighting buildings. Dimensions in mm Double Asymmetric Wide AM5011/12 Asymmetric Medium 5009/10 Symmetric Narrow AM5006/8 175 Double Asymmetric Wide Medium Symmetric Narrow 2 x 15Ø 21Ø Narrow Symmetric AM5006/8 Medium Asymmetric AM5009/10 Double Asymmetric Wide AM5011/12 Vertical Adjustment 435 Ipk 60 Ipk Floodlight Elevation = Medium/Narrow Floodlight Elevation = -60 Double Asymmetric Wide Model Lamp Wattage and Type Lamp Holder Description Weight (kg) AM W SON-TE-40 Narrow symmetric W SON-TE-40 beam/ W SON-TE-40 integral gear W MBI E W MBI E AM /250/400W SON-TE-40 Narrow symmetric beam/ /400W MBI loose gear 9.0 AM W SON-TE W SON-TE W SON-TE W MBI E W MBI E AM /250/400W SON-TE-40 Medium beam/ /400W MBI E-40 loose gear 9.0 AM W SON-TE-40 Double asymmetric, W SON-TE-40 wide beam (60 ) W SON-TE-40 /integral gear W MBI E W MBI E AM /250/400W SON-TE-40 Double asymmetric, wide /400W MBI E-40 beam (60 )/loose gear 9.0 Please specify mains voltage requirements. Weights shown include control gear. Windage 0.230m 2 4.5

7 floodlighting - AL5100 series Stirrup Mount (M8 Fixing) A double asymmetric distribution floodlight Toughened front glass secured by range designed for general purpose use. stainless steel screws and extruded Lamp versions; 100W, 150W, 250W, aluminium clips. 400W SONP-T or MBI Integral rear gear box. Featuring: Double asymmetric reflector system. Die cast aluminium body finished in Sealed to. black polyester powder coating. Dimensions in mm min 300 min 500 min 10 min W / 400W ST x Ø9 max Product Ref Lamp Wattage and Type Lamp Holder Beam Type Description Weight (Kg) AL W SONP-T E-40 Double Asymmetric Integral rear Gear Box W SONP-T E-40 Double Asymmetric Integral rear Gear Box 7.6 AL W SONP-T/MBI E-40 Double Asymmetric Integral rear Gear Box W SONP-T/MBI E-40 Double Asymmetric Integral rear Gear Box 10.3 Please specify mains voltage and requirements. Weights shown include control gear. Windage 0.12m

8 floodlighting - AL5210 series AL5216 AL5218 A versatile double asymmetric beam floodlight offering low light pollution control. Ideally suited to the lighting of multi-use sports areas, tennis courts and general exterior applications. Designed for use with single ended metal halide lamps or high pressure sodium lamps up to 1000W max. Featuring: Body of high pressure die cast aluminium, finished in light grey polyester powder coating (RAL 9006) Steel stirrup with secure locking system and general elevation protractor. Stirrup adjustment 180 max. FLAT GLASS operation with beam emergence at +45 forward throw. Remote control gear with integral ignitor. Anti-vacuum device system fitted to 1KW versions as standard. Optional Cowl accessory (AL5299). Toughened front glass secured by six extruded aluminium clips Silicone rubber gaskets for ingress protection to Double Asymmetric Reflector systems (Medium & Wide) in polished and anodised aluminium. Integral baffle, ensuring excellent glare limitation and increased performance. Rear mounted electrical connection box. 4.7

9 floodlighting - AL5210 series Easy access for re-lamping via opening front glass Stirrup Mount (M8 Fixing) Max 150 Dimensions in mm Min 500 Dimensions in mm Min 90 Max Max Max 180 M8 fixing Product Ref Lamp Wattage and Type Lamp Holder Description Weight (Kg) AL //1000W SON-T E-40 Double Asymmetric Medium /1000W MBI 9.9 AL //1000W SON-T E-40 Double Asymmetric Wide /1000W MBI 9.9 Weight excludes lamp and control gear. Windage 0.12m 2 4.8

10 floodlighting - AL5310 series Dimensions in mm An extensive range of high quality, low wattage floodlights designed for general lighting of small areas, architectural features, facades and security applications Available with a range of lamp types including High Pressure Sodium, Metal Halide and HCI-T / HCI-TS up to a maximum of 150W. Three reflector versions (symmetric, asymmetric and double asymmetric) High pressure die-cast body and frame made from aluminium alloy with a polyester grey finish (RAL7035) Toughened front glass, sealed with silicone gasket M20 electrical cable gland Galvanised steel control gear tray Anodised and sealed aluminum reflector Extruded aluminium stirrup Elevation aiming protractor Integral control gear Sealed to Accessories: AL5399 Aluminium anti-glare louvre in polyester grey (RAL7035). 151 Product Ref Lamp Wattage and Type Lamp Holder Description Lamp Position Reflector Weight (kg) AL W/70W/150W HCI-T G12 Double Horizontal 7.5* 70W/150W HCI-TS RX7s Asymmetric 70W/150W HQI-TS RX7s Reflector (Matt) 70W/150W SONT-D RX7s AL W/70W/150W HCI-T G12 Double Horizontal 7.5* 70W/150W HCI-TS RX7s Asymmetric 70W/150W HQI-TS RX7s Reflector (Bright) 70W/150W SONT-D RX7s AL W/70W/150W HCI-T G12 Asymmetric Horizontal 7.5* 70W/150W HCI-TS RX7s Reflector (Matt) 70W/150W HQI-TS RX7s 70W/150W SONT-D RX7s AL W/70W/150W HCI-T G12 Asymmetric Horizontal 7.5* 70W/150W HCI-TS RX7s Reflector (Bright) 70W/150W HQI-TS RX7s 70W/150W SONT-D RX7s AL W/70W/150W HCI-T G12 Symmetric Vertical 7.5* Reflector AL W/70W/150W HCI-T G12 Symmetric Horizontal 7.5* 70W/150W HCI-TS RX7s Reflector 70W/150W HQI-TS RX7s 70W/150W SONT-D RX7s *Weight includes lamp and control gear (maximum weight in range). Windage 0.123m 2 4.9

11 floodlighting - AL5400 series A range of double asymmetric distribution floodlights, specially designed to provide efficient lighting of large open areas, airports, docks, motorway intersections and industrial complexes. For use with 2x400W or 1KW High Pressure Discharge lamps (SONP-T:MBI), with remote control gear (integral ignitor). Optimum mounting heights 15m to 30m Featuring: Available in 2 beam distributions, narrow and medium Double asymmetric distribution. Beam emittance angle at +60 when installed with front glass horizontal Die-cast aluminium body, polyester powder coated over zinc chromate substrate. Finish metallic grey RAL9006 Front glass sealed to via 2 part silicone gasket Tempered safety front glass, hinged to the body and secured via captive screws and INOX springs. Glass may be quickly opened and closed for easy maintenance Anti-vacuum device fitted to body to prevent mechanical stress on front glass during cooling. High performance reflector in polished and anodised aluminium Stirrup in hot galvanised steel. Fixing ensures flat glass +/-10 elevation adjustment All external screws INOX A2 Separate connection chamber / ignitor housing, connected to rear/top of floodlight body (polyamide 66) 2 x 400W lamp versions as standard, provide added safety should 1 lamp fail Max. ambient temperature +40 C in use 4.10

12 floodlighting - AL5400 series AL5400 floodlight with double Asymmetric light distribution Electrical installation via rear/top connection box. Connection box houses ignitor Electrical installation via rear/top connection box. Connection box houses ignitor Dimensions in mm x 400W SONP-T Floodlight elevation Horizontal +/ º max max 90º 10º max Product Ref Lamp Wattage and Type Lamp Holder Description Weight (Kg) AL5401 2x400W SONP-T or MBI E-40 Narrow 23.0 AL5402 2x400W SONP-T or MBI E-40 Medium 23.0 AL W SONP-T or MBI E-40 Narrow 23.0 AL W SONP-T or MBI E-40 Medium 23.0 Please specify mains voltage and requirements. Weights shown include ignitor. Windage 0.12m

13 floodlighting - AL5 series Asymmetric Beam Floodlight for use with HID lamps (1000W & 2000W). Suitable for lighting sports fields, dock yards, marshalling yards and most large area lighting applications. Lamps: 1000W SON-T. (Vs 240V) 1000W HQI / 2000W HQI. (Vs 415V) Optimum mounting heights 15m to 30m Featuring: Body and rear cover in pressure die cast aluminium, finished in grey polyester powder. Hot dipped galvanised steel stirrup. Toughened front glass, retained with stainless steel clips. Silicone gasket sealing. Thermoplastic high temperature lamp holder. Electrical connection box (nylon) mounted on stirrup. Aluminium reflector 99.85% pure, brightened and anodised. Side elevation protractor.. Double Asymmetric Beam Symmetric Beam 4.12

14 floodlighting - AL5 series Model References Lamp Wattage and Type Lamp Holder Description Weight (kg) AL5601 2KW HPI-T E40Asymmetric Beam 19.0 AL5602 1KW HPI-T E40Asymmetric Beam 19.0 AL5603 HQI-TS2000WNL K12s-7 Asymmetric Beam 19.0 AL5604 MHN-LA1000/842 X528 cable Asymmetric Beam 19.0 AL5605 1KW SON-T E40Asymmetric Beam 19.0 AL5606 2KW HPI-T E40Double Asymmetric Beam 19.0 AL5607 1KW HPI-T E40Double Asymmetric Beam 19.0 AL5608 HQI-TS2000WNL K12s-7 Double Asymmetric Beam 19.0 AL5609 MHN-LA1000/842 X528 cable Double Asymmetric Beam 19.0 AL5610 1KW SON-T E40Double Asymmetric Beam 19.0 AL5611 HQI-TS2000WDS K12s-7 Symmetric Beam 19.0 AL5612 HQI-TS1000WDS K12s-7 Symmetric Beam 19.0 Please specify mains voltage and requirements. Weights shown include ignitor. Windage 0.238m 2. Dimensions in mm 4.13

15 floodlighting - Challenger 1 AL5700 series A double asymmetric distribution, Flat Glass floodlight range, specially designed for lighting outdoor sports grounds, smaller sports stadiums and large open areas where light pollution control is an essential requirement. For use with double ended 2KW or 1KW Metal Halide; double ended lamps or single ended up to W. Featuring: Body of high-pressure die cast aluminium, finished in light grey (RAL7035), Polyester powder coating Medium and wide beam, asymmetric light distributions. Reflector system of high purity, polished and anodised aluminium. Incorporating an internal baffle to improve efficiency and reduce glare. Toughened front glass, secured by extruded and anodised aluminium clips. Galvanised steel stirrup, with additional locking screws. ; with silicone rubber gasketing. Electrical connection box () housing Ignitor, located on side of stirrup. Easy access for re-lamping via opening of the rear cover. Positive closure via large stainless steel catch. Designed to accept a large range of double ended 2KW & 1KW lamps. Variable COWL accessory AL5721 (light grey) to limit overspill and prevent Sky Glow. Variable COWL accessory AL5722 (black) for additional backward overspill control. Variable cowls provide Flat Glass at 65 /70 /75 beam elevations. 4.14

16 floodlighting - Challenger 1 AL5700 series Abacus Light Control System 3. Optional Cowl (Skirt) Accessory A combination of efficient lighting design and careful floodlight design has rewarded Abacus with an international reputation for pioneering high performance floodlighting combined with effective control of light pollution. Specific to Challenger 1 the Abacus Light Control System consists of a series of complementary measures to effectively control light pollution. The final element of the light control system, an adjustable cowl fitting, provides additional control of upward light and direct limitation of overspill. The floodlight and cowl combined achieves an effective Flat Glass profile at a beam elevation of 65 /70 /75. (FIG 3) This effectively provides full cut off at the horizontal. FIG 1 45 IPK 1. Double Asymmetric Reflector The double asymmetric reflector is designed to ensure full flow of light over the lit area from each floodlight. With the main beam emitted from the floodlight at an angle of 45 forward from the normal to the front glass, it results in a flatter appearance (FIG 1). The benefit is that less of the reflector is visible to spectators and onlookers, resulting in low glare to the surrounding locality. Using a cowl achieves better management of overspill. However, cowls will produce a marginal increase in backward illumination due to reflectance off the back edge. This effect is eliminated by the use of a black surface finish to the cowl. (FIG 4) FIG 2 FIG 3 65 /70 /75 HORIZONTAL 2. Internal Baffle The internal baffle re-directs upward stray light back into the floodlight beam, HORIZONTAL providing increased efficiency. At angles above the beam baffle shields direct lamp glare. (FIG 2) FIG 4 BACKWARD LIGHT BLACK INNER FACE Lamp technical data (2KW) OSRAM PHILIPS PHILIPS Lamp Ref: HQI-TS2000WNL MHN-LA2KW400V/842 MHN-LA2KW400V/956 Colour Temperature: 4100K 4200K 5K Lamp Lumen Output: (Initial lm) 225,000 l.lm 220,000 l.lm 190,000 l.lm Lamp Current: 10.7A 9.6A 10.3A Supply Circuit 3-Phase: 380/400/415V 380/400/415V 380/400/415V Supply Current: Starting: 13A 8.3A 8.3A Running: 6.5A 5.6A 5.6A Total Circuit Power: 2180W 2105W 2113W RA:

17 floodlighting - Challenger 1 AL5700 series Dimensions in mm mm Model No. Lamp Wattage and Type Lamp Manufacturer Lamp Holder/support Description AL5706 HQI-TS2000WNL Osram K12s-7 cable Medium Beam AL5707 2KW MHN-LA / 842 & 956 Philips X528 cable Medium Beam AL5709 1KW MHN-LA / 842 & 956 Philips X528 cable Medium Beam AL5711 W SONP-T Osram (plus) Philips (super) AL5713 W SONP-T Osram (plus) Philips (super) E40Medium Beam E40Wide Beam AL5714 HQI-TS2000WNL Osram K12s-7 cable Wide Beam AL5715 2KW MHN-LA / 842 & 956 Philips X528 cable Wide Beam AL5717 1KW MHN-LA / 842 & 956 Philips X528 cable Wide Beam Weight: Kg (with ignitor and without lamp) Windage: m 75 elevation Lamp Illustrations MHN-LA SON-PT HQI 4.16

18 floodlighting - Challenger 1 AL5700 series Aiming Registered design in the following countries Austria RegD No Benelux RegD No Canada RegD No China RegD No line of sight Denmark Eire RegD No MR RegD No D13051 France RegD No Two aiming methods: 1. In-built line of sight aiming feature 2. Separate aiming protractor ensures optimum targeting of individual floodlights to achieve the desired lighting levels. Relamping Germany RegD No Greece RegD No 0682 Hong Kong RegD No M001 India RegD No Spain RegD No Sweden RegD No Switzerland RegD No UK RegD No USA Patent No D Simple lamp changing via opening back cover using a clip system ensures ease of maintenance. 4.17

19 floodlighting - Challenger 2 AL5800 series An asymmetric distribution floodlight range used primarily for side lighting sports systems including roof mounting in stadiums. Body of high-pressure die cast aluminium, finished in light grey (RAL7035), Polyester powder coating. Designed to accept double ended, short arc 2KW & 1KW Metal Halide lamps. Dual provision on side of floodlight body to attach a Gun Sight aiming device to allow accurate beam alignment. Reflector system of high purity, polished and anodised aluminium. Incorporating an internal baffle to improve efficiency and reduce glare. Toughened front glass, secured by extruded and anodised aluminium clips with silicone rubber pads. Aiming line of sight Galvanised steel stirrup, with additional locking screws. ; with silicone rubber gasketing. Optical gun sight fixings are incorporated ensuring simple alignment and attachment of gun sight. Electrical connection box () housing Ignitor, located on side of stirrup. Easy access for re-lamping via opening of the rear cover. Positive closure via large stainless steel catch. Visor accessory AL5922 to reduce upward light and glare. 4.18

20 floodlighting - Challenger 2 AL5800 series Dimensions in mm Model No. Lamp Wattage and Type Lamp Manufacturer Lamp Holder Support Description AL5801 HQI-TS2000WNL Osram K12s-7 Narrow AL5802 HQI-TS2000WNL Osram K12s-7 Medium AL5803 HQI-TS2000WNL Osram K12s-7 Wide AL5804 MHN-LA2KW/842 & 956 Philips X528 Cable Narrow AL5805 MHN-LA2KW/842 & 956 Philips X528 Cable Medium AL5806 MHN-LA2KW/842 & 956 Philips X528 Cable Wide AL5807 MHN-LA1KW/842 & 956 Philips X528 Cable Narrow AL5808 MHN-LA1KW/842 & 956 Philips X528 Cable Medium AL5809 MHN-LA1KW/842 & 956 Philips X528 Cable Wide Weight 15.28kg (with ignitor & without lamp). Windage 0.196m elevation. Lamp technical data (2KW) OSRAM PHILIPS PHILIPS Lamp Ref: HQI-TS2000WNL MHN-LA2KW400V/842 MHN-LA2KW400V/956 Colour Temperature: 4100K 4200K 5K Lamp Lumen Output: (Initial lm) 225,000 l.lm 220,000 l.lm 190,000 l.lm Lamp Current: 10.7A 9.6A 10.3A Supply Circuit 3-Phase: 380/400/415V 380/400/415V 380/400/415V Supply Current: Starting: 13A 8.3A 8.3A Running: 6.5A 5.6A 5.6A Total Circuit Power: 2180W 2105W 2113W RA: Challenger 2 is a Registered Design (see section 4.23)

21 floodlighting - Challenger 3 AL5900 series A symmetrical distribution floodlight range, specially designed for lighting large sports stadia using corner mast systems. Of high performance and compact design, these floodlights provide precision optical control coupled with reduced weight and windage compared to conventional stadium floodlighting. Suitable for use on masts at heights above 20m, it is an ideal choice for use in new stadia or in upgrading existing installations. For use with double ended 2KW or 1KW Metal Halide lamps. Featuring:- Body of high-pressure die cast aluminium, finished in light grey (RAL7035), Polyester powder coating. Extra Narrow, Narrow, Medium and Wide beam light distributions. Galvanised steel stirrup, with additional locking screws. ; with silicone rubber gasketing. Electrical connection box () housing Ignitor, located on side of stirrup. Easy access for re-lamping via opening of the rear cover. Positive closure via large stainless steel catch. Designed to accept double ended, short arc 2KW & 1KW Metal Halide lamps. Dual provision on side of floodlight body to attach a Gun Sight aiming device to allow accurate beam alignment. A choice of visor accessories, AL5921 half concentric louvre to reduce upward light, overspill and glare and AL5922 single blade visor. Reflector system of high purity, polished and anodised aluminium. Incorporating an internal baffle to improve efficiency and reduce glare in Narrow/Medium/Wide versions. Toughened front glass, secured by an aluminium clamping frame. AL5921 Half concentric louvre AL5922 Single Blade Visor 4.20

22 floodlighting - Challenger 3 AL5900 series Lamp technical data OSRAM PHILIPS Lamp Ref: HQI-TS2000/D/S MHN-SA 2KW 400 V/956 Colour Temperature: 5K 5K Lamp Lumen Output: 200,000 l.lm 200,000 I.Lm Lamp Current: 10.3A 11.3A Supply Circuit 3-Phase: 380/400/415V 380/400/415V Supply Current: Starting: 9A 11A Running: 6A 6.6A Total Circuit Power: 2105W 2136W RA:

23 floodlighting - Challenger 3 AL5900 series Dimensions in mm Model No. Lamp Wattage and Type Lamp Manufacturer Lamp Holder/support Description AL5901 2KW HQI-TS 2000WDS Radium / Osram K12s-7 cable Narrow Beam AL5902 2KW HQI-TS 2000WDS Radium / Osram K12s-7 cable Medium Beam AL5903 2KW HQI-TS 2000WDS Radium / Osram K12s-7 cable Wide Beam AL5904 1KW HQI-TS 1000WDS Radium / Osram K12s-7 cable Narrow Beam AL5905 1KW HQI-TS 1000WDS Radium / Osram K12s-7 cable Medium Beam AL5906 1KW HQI-TS 1000WDS Radium / Osram K12s-7 cable Wide Beam AL5907 MHN-SA 2KW 400 V/956 Philips X830/rod Narrow Beam AL5908 MHN-SA 2KW 400 V/956 Philips X830/rod Medium Beam AL5909 MHN-SA 2KW 400 V/956 Philips X830/rod Wide Beam AL5910 MHN-SA 2KW 400 V/956 Philips X830/rod Extra Narrow Beam Weight: Kg (with ignitor and without lamp) Windage: m 70 elevation Lamp Illustrations HQI-TS MHN-SA 4.22

24 floodlighting - Challenger 3 AL5900 series Aiming Registered design in the following countries (Challenger 2 & Challenger 3 ) Austria RegD No line of sight Benelux RegD No Canada RegD No China RegD No Denmark Eire RegD No MR RegD No D13052 Relamping Optical gun sight fixings are incorporated ensuring simple alignment and attachment of AL5931 gun sight aiming unit. France RegD No Germany RegD No Greece RegD No 682 Hong Kong RegD No M002 India RegD No Italy RegD No Korea RegD No Portugal RegD No Spain RegD No Sweden RegD No Simple lamp changing via opening back cover using a clip system ensures ease of maintenance Switzerland RegD No UK RegD No USA Patent No D AL5921 Half concentric louvre AL5922 Single Blade Visor Accessories AL5921 Half Concentric Louvre AL5922 Single Blade Visor AL5931 Gunsight Aiming Unit (Gunsight, mounting block & fixings) 4.23

25 floodlighting - photometric details AM5011/12 400W ST AM5006/8 400W ST 800 Luminous Intensity Diagram Peak Intensity : 745 cd/k.lm (cd/k.lm) cd/k.lm H V AM5009/10 400W ST AL W ST 900 Medium 800 cd/k.lm cd/klm Angles (Through ipk) 4.24

26 floodlighting - photometric details AL W ST AL W MBI 500 cd/klm 400 cd/klm Angles Angles (Through ipk) AL5401 2x400W ST AL x 2kW HQI-TS 2000WNL cd/klm Narrow ST 2x400W º -30º 0º 30º 60º AL5402 2x400W ST cd/k.lm cd/klm Medium ST 2x400W º -30º 0º 30º 60º (Through ipk) 0 0 Applies to both AL5401 and AL (Through ipk) 4.25

27 floodlighting - photometric details AL5715 HQI-TS 2000WNL/MHN-LA 2000W AL5707 HQI-TS 2000WNL/MHN-LA 2000W Symmetric Beam-Wide Asymmetric Beam-Medium cd/klm 400 H V cd/klm 400 H V Angles Angles AL5801 HQI-TS 2000WNL/MHN-LA 2KW842&956 0 Symmetric Beam-Narrow 1 cd/k.lm AL5802 HQI-TS 2000WNL/MHN-LA 2KW842& Symmetric Beam-Narrow AL5901 HQI-TS 2000W/MHN-SA 2KW Symmetric Beam-Narrow cd/klm cd/k.lm H V AL5803 HQI-TS 2000WNL/MHN-LA 2KW842& Angles AL5903 HQI-TS 2000W/MHN-SA 2KW Symmetric Beam-Narrow cd/k.lm cd/klm V 300 H Angles (Through ipk)

28 National Inspection Council for Electrical Installation Contracting APPROVED CONTRACTOR BS EN ISO :1996 BS EN ISO 9001:2000 Abacus Lighting Limited, Sutton-in-Ashfield, Nottinghamshire NG17 5FT, England. Telephone: (+44) Fax: (+44) /2004 Abacus Lighting Limited Flood/3M/McC As Abacus maintains a policy of continuous development and improvement of its products, the right to amend any part of the specifications is strictly reserved.