8641S.WarhawkRd.Conifer,CO (303) (303) fax

Transcription

1

2 8641S.WarhawkRd.Conifer,CO (303) (303) fax

3 MAGSTOP VEHICLE GATES HIGH SPEED BARRIERS HIGH PERFORMANCE BARRIERS WIDE LANE BARRIERS... 8 GENERAL PURPOSE BARRIERS HORIZONTAL SWING BARRIERS SPARE PARTS CONTROL COLUMNS MAGPEDESTRIAN FULL HEIGHT TURNSTILES CATRAX WAIST HIGH PEDESTRIAN TURNSTILES MPP WAIST HIGH PEDESTRIAN TURNSTILES HIGH SPEED RETRACTABLE PANEL PEDESTRIAN BARRIERS MOTORIZED SWING GATES AUTOMATED CLEARANCE GATES PRICE APPENDIX MPR PRICE APPENDIX MPH PRICE APPENDIX PLUS BARRIERS LIMITED WARRANTY * = Left or Right hand version Disclaimer: Prices subject to change without notice MAC is not responsible for typographical errors. MAGSTOP Pg 03 Pg

4 MAGSTOP Vehicle Gates High Speed Barriers MIB 10*-C090 Super High Speed Barrier, 115V, 60hz, 400 watts, in RAL 2000 Orange...5, Factory adjustable opening or closing time from 0.6 to 3.0 seconds Includes our standard octagon arm flange Includes: Controller and built in hall sensor that provides precise barrier arm status information to controller, up/normal/down switch, receptacle, power switch, integrated extra sensory device feature and RS422 output Maximum arm length is 10' - Only when using aluminum round arm # MSB 4B-030 Maximum arm length for automatic open on power failure is 10 with round arm MSB 4B-030 or MSB 5N-030 (Round arm requires optional flange ) SPECIAL COLOR: As per customer's request in RAL shades, powder coated RAL Color Code only, pricing for other color codes may vary ARM FLANGES: Swing away flange for octagonal arm (MSB 5N-030) Swing away flange for round arm (MSB 4B-030) Wood arm flange (tapered 1" x 4" arm) Relocking swing away flange for foam covered arm part # MSB 9N BARRIER ARMS: MSB 5N foot aluminum barrier arm octagonal shaped - Standard arm flange required MSB 5N foot aluminum barrier octagonal shaped - Standard arm flange required MSB 5B foot aluminum barrier octagonal, swing away arm, requires part # MSB 4B foot aluminum round, swing away arm, requires part # MSB 9N foot foam covered arm, requires part # MSB 9N foot foam covered arm, requires part # Wood Arms (1 x 4 ) Require part # or ACCESSORIES: Contact for release of barrier arm (arm mounted - contact open) Inductive boom break away sensor kit foam protective edge for octagonal arm, fits in notch of newly designed gate arms - Each Audible buzzer / alarm with LED X6 sawcut 20 inductive sawcut loop - Each * = Left or Right hand version Pg 04

5 High Speed Barriers Continuation MIB 20*-C100 High Speed Barrier, 115V, 60hz, 240 watts, in RAL 9010 white, RAL 2000 orange, and RAL 1028 yellow.... 3, Opening or closing time 0.9 seconds with our standard octagon arm flange Gate drive unit is adjusted for arm that is ordered with unit Includes: MLC controller with display, built in position sensor provides precise barrier arm status information to controller, up/normal/down switch, receptacle, output relays, power switch and built in dual channel loop detecto. Maximum arm length for automatic open on power failure is 10 (Round arm requires optional flange ) SPECIAL COLOR: As per customer's request in RAL shades, powder coated RAL Color Code only, pricing for other color codes may vary ARM FLANGES: Swing away flange for octagonal arm (MSB 5N-025) Swing away flange for round arm (MSB 4B-030) Wood arm flange (tapered 1" x 4" arm) Wood arm adapter for octagonal flange - Minimum requirement if wooden arm is used Relocking swing away flange for foam covered arm part # MSB 9N BARRIER ARMS: MSB 5N foot aluminum barrier arm octagonal shaped - Standard arm flange required MSB 5B foot aluminum barrier octagonal, swing away arm, requires part # MSB 4B foot aluminum round, swing away arm, requires part # MSB 9N foot foam covered arm, requires part # MSB 9N foot foam covered arm, requires part # Wood Arms (1 x 4 ) Requires part # or ACCESSORIES: Contact for release of barrier arm (arm mounted - contact open) Inductive boom break away sensor kit MLC-programming chip card, with software MLC50-E100 RS232 or RS422 or RS485 com box, requires MLC10 or MLC MLC30-E100 24VDC I/O BOX, 6 INPUTS/7 OUTPUTS, input/output extension module for gate and induction loop status, directional logic, differential count, arm position status LED signal lamp safety red - LED lamp w/ blunt cut MSS1C-900 Control unit for 20 LED signal lamps (# ) at maximum foam protective edge for octagonal arm, fits in notch of newly designed gate arms - Each Battery back-up Audible buzzer / alarm with LED X6 sawcut 20 inductive sawcut loop - Each * = Left or Right hand version Pg 05

6 High Performance Barriers MIB 30*-C100 High Performance Barrier 115V, 60Hz, 120 watts in RAL 9010 white, RAL 2000 orange, RAL 1028 yellow....3, Opening or closing time 1.4 to 1.9 seconds with our standard octagon arm flange Includes: MLC controller with display, built in position sensor provides precise barrier arm status information to the controller, up/normal/down switch, power switch, relay outputs, convenience receptacle and built in dual channel loop detector Maximum arm length for MIB octagon arm Maximum arm length for MIB 30 automatic open on power failure is 10 SPECIAL COLOR: As per customer's request in RAL shades, powder coated RAL Color Code only, pricing for other color codes may vary ARM FLANGES: Swing away flange for octagonal arm up to 12 feet (MSB 5B-035) Swing away flange for round arm up to 10 feet (MSB 4B-030) Wood arm flange (tapered 1" x 4" arm) Wood arm Adapter for octagonal flange - Minimum requirement if wooden arm is used BARRIER ARMS: MSB 5N foot aluminum barrier arm octagonal shaped - Standard arm flange used MSB 5N foot aluminum barrier arm octagonal shaped - Standard arm flange used MSB 5N foot aluminum barrier arm octagonal shaped - Standard arm flange used MSB 5K-025** 8 foot articulating aluminum arm octagonal shaped - Standard arm flange used MSB 5K-030** 10 foot articulating aluminum arm octagonal shaped - Standard arm flange used MSB 5K-035** 12 foot articulating aluminum arm octagonal shaped - Standard arm flange used MSB 5B foot aluminum octagonal swing away arm, requires part # MSB 4B foot aluminum round swing away arm, requires part # Wood Arms (1 x 4 ) Require part # or ACCESSORIES: foam protective edge for octagonal arm, fits in notch of newly designed gate arms - Each Contact for release of barrier arm (arm mounted - contact open) MLC-programming chip card, with software MLC50-E100 RS232 or RS422 or RS485 com box, requires MLC10 or MLC MLC30-E100 24VDC I/O BOX, 6 INPUTS/7 OUTPUTS, input/output extension module for gate and induction loop status, directional logic, differential count, arm status MAP 5H-110 Supporting pillar w/ electro-mechanical arm lock, RAL 2000 orange only Custom Color Custom shade RAL color powder coat for MAP support pillars MMV1C-100 Control unit for electro-mechanical arm lock signal lamp 24VDC for MSB 5N-*** arm, 100mm dia. (Orange Lens) MSS1C-100 Control unit for 3 signal lamps (# ) at maximum Set of 2 LED signal lights w/ blunt cut, Red (one per side of boom arm) MSS1F-500 LED signal controller (Continuous Flash) and power supply LED signal continuos ON/OFF in up position with power supply and inductive limit switch kit Battery back-up Audible buzzer / alarm with LED X6 sawcut 20 inductive sawcut loop - Each ** Customer to provide articulating arm dimensions *** length of arm using Magnetic numbering * = Left or Right hand version Pg 06

7 High Performance Barriers Continuation MIB 40*-C900 High Performance Barrier 115V, 60Hz, 120 watts, in RAL 9010 white, RAL 2000 orange, RAL 1028 yellow...3, Opening or closing time 4.0 seconds with our standard octagon arm flange Includes: MLC controller with display, built in position sensor provides precise barrier arm status information to the controller, up/normal/down switch, power switch, relay outputs, convenience receptacle and built in dual channel loop detector Maximum arm length for MIB 40 is 20 octagon arm Maximum arm length for MIB 40 automatic open on power failure is 15 - arms over 14 require either a pendulum ( ) or support pillar (MAP5N/H-100) SPECIAL COLOR: As per customer's request in RAL shades, powder coated RAL Color Code only, pricing for other color codes may vary ARM FLANGES: Swing away flange for octagonal arm up to 15 feet (MSB 5B-045) Wood arm flange (tapered 1" x 4" arm) Wood arm Adapter for octagonal flange - Minimum requirement if wooden arm is used BARRIER ARMS: MSB 5N foot aluminum barrier arm octagonal shaped - Standard arm flange used MSB 5N foot aluminum barrier arm octagonal shaped - Standard arm flange used **** MSB 5N foot aluminum barrier arm octagonal shaped - Standard arm flange used**** MSB 5K-035** 12 foot articulating aluminum arm octagonal shaped - Standard arm flange used MSB 5K-045** 15 foot articulating aluminum arm octagonal shaped - Standard arm flange used MSB 5K-060** 20 foot articulating aluminum arm octagonal shaped - Standard arm flange used MSB 5B foot aluminum octagonal swing away arm, requires part # Wood Arms (1 x 4 ) Require part # or ACCESSORIES: Pendulum support required for arm arms exceeding 14' **** foam protective edge for octagonal arm, fits in notch of newly designed gate arms - Each Contact for release of barrier arm (arm mounted - contact open) MAP 5N-110 Supporting pillar for arms MSB 5N*** RAL 2000 orange only MAP 5H-110 Supporting pillar w/ electro-mechanical arm lock, RAL 2000 orange only Custom Color Custom shade RAL color powder coat for MAP support pillars MMV1C-100 Control unit for electro-mechanical arm lock signal lamp 24VDC for MSB 5N*** arm, 100mm dia. (Orange Lens) MSS1C-100 Control unit for 3 signal lamps at maximum Set of 2 LED signal lights w/ blunt cut, Red (one per side of boom arm) MSS1F-500 LED signal controller (Continuous Flash) and power supply LED signal continuous ON/OFF in up position with power supply and inductive limit switch kit MLC-Programming chip card, with software MLC50-E100 RS232 or RS422 or RS485 com box, requires MLC10 or MLC MLC30-E100 24VDC I/O BOX, 6 Inputs/7 Outputs, input/output extension module (loop/arm status, directional logic, counts) Battery back-up Audible buzzer / alarm with LED X6 sawcut 20 inductive sawcut loop - Each ** Customer to provide articulating dimensions *** length of arm using Magnetic numbering **** Support required for arms over 14 feet * = Left or Right hand version Pg 07

8 Wide Lane Barriers NOTE: Two supports are required for arms over 27 feet, either 2 pendulums ( ) or 1 pendulum and one support pillar (MAP 6N/H-110) MTS 6*-920 Wide Lane Barrier 115V, 250 watts, available in RAL 2000 orange only... 6, Opening or closing time 6.5 seconds maximum arm length 27 feet Arm length for automatic open on power failure - 20 (requires regular adjustment)** Includes: single limit switch with one cam for safety function MUB 4C-403 multifunction logic controller Two single channel detectors (M1E* series-11-pin) NOT UL Approved --- NOTE: Arms over 27' require 2 supports MTS 8*-920 Traffic barrier 115V, 250 watts, available in RAL 2000 orange only...6, Opening or closing time 8.5 seconds maximum arm length 33 feet Arm length for automatic open on power failure - 27 (requires regular adjustment)** Includes: single limit switch with one cam for safety function MUB 4C-403 multifunction logic controller Two single channel detectors (M1E* series-11-pin) UL Approved --- NOTE: Arms over 27' require 2 supports SPECIAL COLOR: As per customer's request in RAL shades, powder coated RAL Color Code only, pricing for other color codes may vary ARM FLANGES: Swing away flange for straight arm maximum arm length , BARRIER ARMS: MSB 6N foot aluminum barrier arm octagonal shaped**** MSB 6N foot aluminum barrier arm octagonal shaped****... 1, MSB 6N foot aluminum barrier arm octagonal shaped****... 1, ACCESSORIES: Pendulum support MAP 6N-110 Support pillar for MTS arms RAL 2000 orange only MAP 6H-110 Support pillar with electro-mechanical arm lock for MTS barriers RAL 2000 orange only Custom Color Custom shade RAL color powder coat for MAP support pillars MMV1C-100 Control unit for electro-mechanical arm lock signal lamp 24V mounted for MTS series, 100mm dia. (Orange Lens) MSS1C-100 Control unit for 3 signal lamps set of 2 LED signal lights w/ blunt cut, Red (one per side of boom arm) MSS1F-500 LED signal controller (Continuous Flash) and power supply LED signal continuos ON/OFF in up position with power supply and inductive limit switch kit Limit switch for MTS 6/ Audible buzzer / alarm with LED X6 sawcut 20 inductive sawcut loop - Each **** One support required for arms over 14 feet, either pendulum ( ) or one support pillar (MAP 6*-110) ** Requires regular maintenance every 3-6 months springs & lever arm adjustment * = Left or Right hand version Disclaimer: Prices subject to change without notice TURNSTILES AC is not responsible for typographical errors. Pg 08

9 General Purpose Barriers MBE 35*-C100 General Purpose Barrier, 115V, 60hz, 65 watts, in RAL 9010 white or RAL 2000 orange...2, Opening 2.3 seconds, closing time 2.8 seconds with octagon arm flange Each gate is pre-adjusted for the arm that is ordered Includes: MBE single board controller, up/normal/down switch, receptacle and power switch - MBE controller includes: 6 inputs and 4 output relays, 500 ma 24V DC supply and 11 functions for most applications MBS-110A-C100 controller boom impact detection technology Maximum arm length is 12' Maximum arm length auto open on power failure 10' Door location cannot be changed MBE 50*-C100 General Purpose Barrier, 115V, 60hz, 65 watts, in RAL 9010 white or RAL 2000 orange...2, Opening 4.6 second, closing time 4.9 second with octagon arm flange Each gate is pre-adjusted for the arm that is ordered Includes: MBE single board controller, up/normal/down switch, receptacle and power switch - MBE controller includes: 6 inputs and 4 output relays, 500 ma 24V DC supply and 11 functions for most applications MBS-110A-C100 controller boom impact detection technology Maximum arm length is 15' Maximum arm length auto open on power failure 12' Door location cannot be changed SPECIAL COLOR: As per customer's request in RAL shades, powder coated RAL Color Code only, pricing for other color codes may vary BARRIER ARMS: MSB 5N foot aluminum barrier arm octagonal shaped MSB 5N foot aluminum barrier arm octagonal shaped MSB 5N foot aluminum barrier arm octagonal shaped MSB 5N foot aluminum barrier arm octagonal shaped, pendulum support is required MSB 5K-025_ECO 8 foot articulating aluminum arm octagonal shaped ** MSB 5K-030_ECO 10 foot articulating aluminum arm octagonal shaped ** MSB 5K-035_ECO 12 foot articulating aluminum arm octagonal shaped ** MSB 5K-045_ECO 14 foot articulating aluminum arm octagonal shaped ** Wood Arms (1 x 4 ) Require part # ACCESSORIES: Limit switch kit Pendulum support required for arms exceeding 14' MBE-ENF12 Integrated traffic spike system for 12 foot MBE barrier (barrier not included) Wood arm (1 x 4 ) adapter for octagonal flange, required if wooden arm is used MID1E-800 Single channel loop detector 24V DC MID2E-800 Dual channel loop detector 24V DC New design foam octagonal barrier boom protection - Per 10 section Set of 2 LED signal lights w/ blunt cut, Red (one per side of boom arm) requires part # V DC 1A Power Supply Audible buzzer / alarm with LED X6 sawcut 20 inductive sawcut Loop - Each ** Customer to provide articulating arm dimensions * Left or Right hand version Pg 09

10 Horizontal Swing Barriers MHS 8W-*** Horizontal Swing Barrier, 40 seconds for 90 degree swing....see BELOW 115VAC, 60hz, 580 watts blockable torque motor, no additional heater required Heat generated by the motor prevents condensation and corrosion Adjustable opening and closing angle Maximum arm length 33 on each side Pyramid shaped stainless steel housing design, powder coated RAL 2000 orange All internal components are accessible through two removable doors Includes control unit for dead man operation Open/closed indication Arm length over 10 requires double arm construction on either side Signal lamps not included MHS 8W One side single arm max arm length , MHS 8W Two sides single arm max arm length 10 both sides... 19, MHS 8W One side double arm max arm length , MHS 8W Two sides double arm max arm length 33 sides... 20, SPECIAL COLOR: As per customer's request in RAL shades, powder coated RAL Color Code only, pricing for other color codes may vary BARRIER ARMS: MSB 6N-030 Single arm 10 octagonal aluminum arm MSB 8D-060 Double arm 20 octagonal aluminum arm... 1, MSB 8D-080 Double arm 27 octagonal aluminum arm... 3, MSB 8D-100 Double arm 33 octagonal aluminum arm... 3, OPTIONS: Multifunction control unit on request Signal lamp dia. 180mm, 6VDC red or yellow, one side only MSS 3C-*** Control unit for signal lamps 6V DC output max 8 lamps signal lamp 24V DC for MHS profile arm, 100mm dia. (Orange Lens) MSS1C-100 Control unit for 3 24V DC signal lamps Lights may reduce maximum arm length, please call for details Special requirements on request Main power disconnect when access door is open X6 sawcut 20 inductive sawcut loop - Each *** = Left Version or Right number hand version * = Left or Right hand version Disclamer: Disclaimer: Prices subject to to change without notice MAC TURNSTILES is not responsible is not responsible for typographical for typographical errors. errors. Pg 010 Pg 010

11 Spare Parts CONTROLLERS MUB 3C-403 Multifunction logic controller for MSE3 with program MUB 4C-403 Multifunction logic controller, for MTS, MSV1 & MSV MLC 11-U100 Magnetic Lane Controller (MLC) control unit for MIB MLC 10-U100 Magnetic Lane Controller (MLC) control unit MLC 30-E100 24VDC I/O BOX, 6 INPUTS/7 OUTPUTS, I/O extension module MLC 50-E100 RS232 com box, requires MLC30 I/O box MBE single board controller MBS-110A-C100 Controller for instant reverse feature on MBE series (requires part # ) LOOP DETECTORS DIN RAIL Mount MID1E-800 Single channel loop detector 24V DC, DIN RAIL Mount MID2E-800 Dual channel loop detector 24V DC, DIN RAIL Mount VEK M4D-A Four channel loop detector 24V DC, DIN RAIL Mount, Serial Communication VEK S4 Four channel loop detector 24V DC, DIN RAIL Mount, Serial Communication...1, (Detects speed, direction, length and vehicle classification) 11-Pin Socket M1E-110 Single channel detector, with connection jack for diagnostic unit 110V AC M1E-24 Single channel detector, with connection jack for diagnostic unit 24V DC M1E-24AC Single channel detector, with connection jack for diagnostic unit 24V AC M2E-220 Dual channel detector, with connection jack for diagnostic unit 240V AC M1E-HARNESS Wire harness for Magnetic M1E 11-Pin detector Pin relay socket MWD BF-A Radar motion detector Weather proof plastic housing w*h*d = 155*58*132mm With directional modes for placing on opposing sides of doorways With the ability to usually determine between people & vehicles MWD RC Remote control for radar motion detector Plastic housing with push buttons This eliminates climbing up and down ladders to make adjustments CN1 4 input differential counting device Plastic case for DIN RAIL mounting 24 V AC or DC power supply Pg 011

12 Spare Parts Continuation SPECIAL ACCESSORIES Limit switch UL assembly Two position switch (plastic) OPEN/CLOSE for guard operation Three position switch (plastic) OPEN/CLOSE/NORMAL Green push button switch Red push button switch X6 sawcut 20 inductive sawcut loop - Each Boom arm safety sensor - retroreflective photo beam set (transmitter mounted to barrier housing) ARM ACCESSORIES M8 Nylon hex nut - Available in multiples of 100 pieces Pendulum support hardware kit Pendulum support for MSB 5N and 6N series MAP 5N-110 Supporting pillar for MSV/MIB arms - RAL 2000 orange only - Each MAP 5H-110 Supporting pillar with electro-mechanical arm lock for MSV/MIB barriers RAL Each MAP 6N-110 Supporting pillar for MTS arms - orange only RAL Each MAP 6H-110 Supporting pillar with electro-mechanical arm lock for MTS barriers RAL Each MMV1C-100 Control unit for mechanical arm lock Internal lock component Aluminum skirt for MIB 30/40 Maximum 3.5/4.0 meters - Per Meter Aluminum skirt for MTS 6/8 Maximum 6.0/8.0 meters - Per Meter signal lamp 24V for MSB 5N*** arm, 100mm dia.(orange Lens) signal lamp 24V for MSB 6N*** arm, 100mm dia.(orange Lens) MSS1C-100 Control unit for 3 signal lamps (# ) at maximum Set of 2 LED signal lights w/ blunt cut, Red (one per side of boom arm) MSS1F-500 LED signal controller (Continuous Flash) and power supply LED signal continuos ON/OFF in up position with power supply and inductive limit switch kit ACCESSORIES Capacitor 12 μf Capacitor 20 μf MIB 20/30/35 - half strength spring - per spring - Each MIB 40 - full strength spring - per spring - Each Rubber end stop - MIB series - Each Rubber end stop - MBE series - Each *** length of arm using Magnetic numbering * = Left or Right hand version Pg 012

13 Spare Parts Continuation CONTROL PANELS MKI 6P-175 Desk panel for one MLC/MUB MKI 6P-275 Desk panel for two MLC/MUB MKI 6P-375 Desk panel for three MLC/MUB MKI 6P-475 Desk panel for four MLC/MUB FEATURES: Allows the gate to function as: 1. Permanently opened 2. Dead man operation 3. Pulse sequence OPEN/CLOSE with one button 4. Pulse operation OPEN/CLOSE with two separate buttons 5. Automatic operation When the controller is set to the appropriate mode LED's indicate direction of barrier arm (open = green, red = close) DRIVE UNITS MIB 20 SERIES BDU20*-C900 Drive unit corresponds to MIB 20-C , Opening/closing time 0.9 seconds - Max arm length 10 Aluminum round arm only # MSB 4B Adjusted to desired arm length Maximum arm length auto open on power failure 8' MIB 30 SERIES BDU30*-C900 Drive unit corresponds to MIB 30-C , Opening/closing time 1.4 seconds - Max arm length is 12 Adjusted to desired arm length Maximum arm length auto open on power failure 10 MIB 40 SERIES BDU40*-C900 Drive unit corresponds to MIB 40-C , Opening/closing time 4.0 seconds - Max arm length is 20 Adjusted to desired arm length Maximum arm length auto open on power failure 15 MOTORS MC43C-370 Torque motor corresponds to MSV 3 barrier 65 W 1.8 sec... 1, MC63C-270 Torque motor corresponds to MBE 35 and MSE 3 barrier 45 W sec... 1, MC63C-275 Torque motor corresponds to MBE 50 barrier 45 W sec... 1, MC83C-380 Torque motor corresponds to MSV 4 barrier 72 W 3.5 sec... 1, MC83C-390 Torque motor corresponds to MSV 5 barrier 72 W 7.5 sec... 1, SAM Torque motor corresponds to MTS 6 barrier 280 W 6.5 sec - Each... 1, SAM Torque motor corresponds to MTS 8 barrier 280 W 8.5 sec - Each... 1, * Right hand or Left hand version * = Left or Right hand version Pg 013

14 Control Columns MEC 10M-C920 MEC 10M-920 Remote Card Access Station...3, Including MCR50H-G900 proximity card reader MEC 10M-C900 housing post with MRC50 controller Backlit display TCP/IP converter Standard color RAL 2000 Orange OPTIONS: MEC 10M-A100 MIDI control column The housing consists of 14 gage sheet steel housing with a large colorless anodized aluminum front plate. The slim and economic design is perfectly suited for narrow driveways and applications with space limitations. Standard color RAL 2000 Orange Serial to TCP/IP converter Backlit LCD display for remote entry and exit stations Displays all messages necessary to interact with the patron entering or exiting the facility MRC50-*** MRC50E-*** Multifunction Controller with 8 Inputs/4Outputs and 4 RS232 connections... 1, MCR09H-G900 Proximity access control card reader TCP/IP (Note: For extended read range capabilities of feet - please refer to the AVI Automatic Vehicle Identification section) Proximity access control card, (Facility code 128) (100 card minimum) SPECIAL COLORS: As per customer's request in RAL shades, powder coated (i.e. RAL 9010 white, RAL 1028 yellow) RAL Color Code only, pricing for other color codes may vary MEC 10N-C950 MEC 10N-C950 Token and Coin Validator, Offline... 3, Stand alone operation including control column RAL 2000 Orange with removable cover, aluminum front plate and token bin Multifunction token and coin acceptor - includes relay, counter and power supply OPTIONS: Heater and ventilator 600 watts Token - 26mm diameter, Each SPECIAL COLORS: As per customer's request in RAL shades, powder coated (i.e. RAL 9010 white, RAL 1028 yellow) RAL Color Code only, pricing for other color codes may vary Pg 014

15 Control Columns Continuation COMMON FEATURES of the MEC 10E-A100 and MEC 10M-A100 The housing consists of 14 gage sheet steel housing with a colorless anodized aluminum front plate for mounting devices. The slim and economic design is perfectly suited for narrow driveways and applications with space limitations Standard color RAL2000 Orange Holes for mounting and conduit are provided MEC 10E-A100 Control Column, Dual Height for Cars and Trucks... 1, Consists of two MEC 10M columns bolted together Overall dimensions 84.5" tall x 10" wide x 10" deep, device cavity 8" deep Two large front access doors - 30" tall x 10" wide Alum plate dimension 12" x 10" (unobstructed mounting area 10.5" x 8.5") Perfectly suited for narrow driveways and applications with space limitations Standard color RAL 2000 Orange MEC 10M-A100 MIDI Control Column Single MEC 10M MIDI control column Overall dimensions 42.25" tall x 10" wide x 10" deep, device cavity 8" deep One large front access doors - 30" tall x 10" wide Alum plate dimension 12" x 10" (unobstructed mounting area 10.5" x 8.5") 14 gage sheet steel housing Perfectly suited for narrow driveways and applications with space limitations Standard color RAL 2000 Orange COMMON FEATURES of the MEC 10N, MEC 10H and MEC 10L The housing consists of 14 gage sheet steel housing with a colorless anodized aluminum front plate for mounting devices. The large design is ideal for applications requiring several peripheral devices The housing base, door and mounting is similar to the MIB housing with a stainless steel bottom frame, removable door, and channel bar mounting providing room for conduits MEC 10N-A100 Control Column...1, Overall dimensions 42" tall x 14" wide x 18" deep, device cavity 16" deep Large front access door 22" tall x 11" wide Alum plate dimension 14" x 9" (unobstructed mounting area " x 8.125") Pg 015

16 Control Columns Continuation MEC 10H-A100 Control Column...1, Overall dimensions 48" tall x 14" wide x 18" deep, device cavity 16" deep Large front access door 22" tall x 11" wide Alum plate dimension 14" x 15" (unobstructed mounting area " x 13.75") MEC 10L-A100 Car and Truck Control Column....2, Overall dimensions 88" tall x 14" wide x 17" deep, device cavity 15" deep Large front access door 22" tall x 11" wide Alum plate mounted to roller bearing slides - extends 11" SPECIAL COLORS: RAL 9010 white, additional charge RAL 1028 yellow, additional charge RAL Color Codes only Pricing for other color codes may vary Pg 016

17 MAGPEDESTRIAN Full Height Turnstiles MPT 33C-C350G Full Height Turnstile, Bi-directional, Solenoid Locking System 115V AC... 4, High security modular design featuring galvanized cage and column 120 degree U-shaped bars - includes plates for access readers Top control housing made of mild steel and powder coated with RAL 7042 Gray - includes multifunction controller MSC10-E100 NOTE: Standard configuration is free spin in both directions with no power applied. When specified on purchase order to lock in one or both directions - turnstile will be configured at the factory at no additional cost. * When ordered at a later date the kit is available at additional cost (part # ) Packaging is required with all turnstiles and is NOT discountable Requires mounting bolts & hardware (MPTA ) OPTIONS: MPTA Mounting bolts & hardware Foundation ring for MPT, consisting of galvanized steel including adjusting screws 15cm tall... 2, Suited for installations on/in unstable surfaces Additional kit for MPT33C to change from unlocked with no power to locked each direction with no power in either one or both directions Manual release kit to unlock turnstile whether or not power is supplied to the unit each direction MAU-TSCPMPT33 MPT33 turnstile canopy 8' x 6' non powder coated with 4 gussets MPT 33C-C350GPC Full Height Turnstile, Bi-directional, Solenoid Locking System 115V AC... 5, High security modular design, 120 degree U-shaped bars with galvanized and RAL 7042 gray powder coated cage and column - includes plates for access readers Top control housing made of mild steel and powder coated with RAL 7042 Gray - includes multifunction controller MSC10-E100 NOTE: *picture shown as galvanized Standard configuration is free spin in both directions with no power applied. When specified on purchase order to lock in one or both directions - turnstile will be configured at the factory at no additional cost. * When ordered at a later date the kit is available at additional cost (part # ) Packaging is required with all turnstiles and is NOT discountable Requires mounting bolts & hardware (MPTA ) OPTIONS: MPTA Mounting bolts & hardware Foundation ring for MPT, consisting of galvanized steel including adjusting screws 15cm tall... 2, Ideal for installations on/in unstable surfaces Additional kit for MPT33C to change from unlocked with no power to locked each direction with no power in either one or both directions Manual release kit to unlock turnstile whether or not power is supplied to the unit each direction MAU-TSCPMPT33 MPT33 turnstile canopy 8' x 6' non powder coated with 4 gussets Pg 017

18 Full Height Turnstiles Continuation MPT 33C-C310SS Full Height Turnstile, Bi-directional, Solenoid Locking System 115V AC... 21, High security modular design featuring stainless steel cage and column 120 degree U-shaped bars - includes plates for access readers Top control housing made of mild steel and powder coated with RAL 7042 Gray - includes multifunction controller MSC10-E100 NOTE: *picture shown as galvanized Standard configuration is free spin in both directions with no power applied. When specified on purchase order to lock in one or both directions - turnstile will be configured at the factory at no additional cost. * When ordered at a later date the kit is available at additional cost (part # ) Packaging is required with all turnstiles and is NOT discountable Requires mounting bolts & hardware (MPTA ) OPTIONS: MPTA Mounting bolts & hardware Foundation ring for MPT, consisting of galvanized steel including adjusting screws 15cm tall... 2, Ideal for installations on/in unstable surfaces Additional kit for MPT33C to change from unlocked with no power to locked with no power in either one or both directions Manual release kit to unlock turnstile whether or not power is supplied to the unit MAU-TSCPMPT33 MPT33 turnstile canopy 8' x 6' non powder coated with 4 gussets MPT 53C-C350G MPT Double Full Height Turnstile, Bi-directional, Solenoid Locking System 115V AC... 13, High security modular design featuring galvanized cage and column 120 degree U-shaped bars - includes plates for access readers Top control housing made of mild steel and powder coated with RAL 7042 Gray - includes multifunction controller MSC10-E100 NOTE: *picture shown as galvanized Standard configuration is free spin in both directions with no power applied. When specified on purchase order to lock in one or both directions - turnstile will be configured at the factory at no additional cost. * When ordered at a later date the kit is available at additional cost (part # ) Packaging is required with all turnstiles and is NOT discountable Requires mounting bolts & hardware (MPTA ) OPTIONS: MPTA Two (2) sets of mounting bolts & hardware part Foundation ring for MPT, consisting of galvanized steel including adjusting screws 15cm tall... 4, Ideal for installations on/in unstable surfaces Additional kit for MPT53C to change from unlocked with no power to locked each direction with no power in either one or both directions Manual release kit to unlock turnstile whether or not power is supplied to the unit each direction Pg 018

19 Full Height Turnstiles Continuation MPG 12 MPG 12 Full Height, Bi-directional ADA Swing Gate , The MPG series of swing doors is designed to control cyclists, wheelchair users, users with oversized load requirements (i.e. maintenance personnel) or similar user groups The drive system consists of our well proven motor and gearing technology already known from our full height turnstiles and is equipped with a respective locking unit The MHTM motor moves the door with slightest static or dynamic impact power - 2 x 90 bidirectional movement Galvanized steel construction Catrax Waist High Pedestrian Turnstiles CATRAX PLUS and FIT Catrax Plus - Mild Steel Black Powder Coat... 2, Catrax Plus - Brushed Stainless Stainless Steel... 2, Catrax Fit - Black Powder Coat Only with Standard Arm (Not shown - Similar to Plus, but no accessible base housing; no door)...1, Catrax Plus and Fit turnstiles are the best value access control solutions available in the market These models stand out for their versatility, attractive design and, especially for their ease of integration with other security components, such as magnetic, biometric and proximity readers Passageway allow for a smooth turn and lessen the impact of the patrons after each passage Optical sensors and electromagnets are used to activate locks, thus preventing mechanical wear and increasing equipment life NOTE: Picture Shown in Stainless Steel Version INCLUDES: Operational Pictogram Allows for visual identification of permitted access (red "X", green "arrow" LED Technology) Power Supply Power supply developed especially for Catrax product line, protects against electrical surges and short-circuits Controller/Displays The micro processor based unit can be easily interfaced with most available control devices - Four opto-isolated inputs (programmable to dry or hot inputs), two directional inputs, alarms and outputs for directional LED pictograms, RS232 communication port OPTIONS: Electronic Counter Bi-directional electronic counter Drop Arm Drop arm anti-panic/emergency mechanism Drop Box Drop box feature LCD Display Back lit LCD display up to 20 standard messages Top Cover Top cover Pg 019

20

21

22

23

24

25

26

27 Pedestrian Price Appendix MPH 2010 Continued C C Add $1, Add $1, Add $1, Add $1, Pg 027

28 Pedestrian Price Appendix PLUS Barriers 2010 $16,325 Per Lane $25,665 Per Lane $36,845 Per Lane $39,875 Per Lane $1,450 Per Unit $6,875 Per Suite Pg 028

29 LIMITED WARRANTY (TURNSTILES) warrants that all products distributed by TURNSTILES will be free from any defects in material and workmanship for the warranty periods described below under normal operating conditions when installed in accordance with TURNSTILES' installation instructions, normal wear and tear excepted. Please contact TURNSTILES if you are uncertain whether specific parts are covered under warranty for a particular product. The warranty period for the following TURNSTILES products are: Vehicle Gates... 2 Years or 2 Million Cycles Whichever Occurs First Pedestrian Gates...1 Year or 2 Million Cycles Whichever Occurs First Loop Detectors...1 Year The warranty period shall start from the date of shipment of the product by TURNSTILES. In no event shall the limited warranty provided hereunder for any products extend for more than 2 years from the date the product was shipped by TURNSTILES. During the warranty period, TURNSTILES will repair or replace at its option, any of its products which have been found to be defective. A Return Material Authorization Number (RMA) must be obtained before product is returned, and products must be shipped freight prepaid to ; 8641 S. Warhawk Road; Conifer, CO TURNSTILES is not responsible for removal, installation, or any incidental expenses incurred in shipping the product to or from TURNSTILES. This limited warranty extends only to the original purchaser of the product and shall not cover repair, labor or replacement of parts that are by nature expendable. All TURNSTILES products are subject to design and/or appearance modifications, which are production standards at the time of shipment. TURNSTILES may, but shall not be required, to, modify or update products shipped prior to a current production standard. All TURNSTILES products are subject to design and/or appearance modifications, which are production the time of shipment. TURNSTILES may, but shall not be required, to, modify or update products shipped prior to a current production standard. TURNSTILES OFFERS NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE LIMITED WARRANTIES OFFERED HEREIN ARE THE SOLE AND EXCLUSIVE REMEDIES AVAILABLE TO THE PURCHASER. CORRECTION OF DEFECTS, IN THE MANNER AND FOR THE PERIOD OF TIME DESCRIBED HEREIN, SHALL CONSTITUTE THE COMPLETE FULFILLMENT OF ALL LIABILITIES OF TURNSTILES TO THE PURCHASER WITH RESPECT TO THE COVERED PRODUCT, AND SHALL CONSTITUTE FULL SATISFACTION OF ALL CLAIMS, WHETHER BASED ON CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE. IN NO EVENT SHALL TURNSTILES BE LIABLE FOR ANY LOSS OF PROFITS OR ANY INDIRECT, CONSEQUENTIAL, INCIDENTAL, SPECIAL OR PUNITIVE DAMAGES ARISING OUT OF TURNSTILES BREACH OF THIS LIMITED WARRANTY, OR ARISING OUT OF THE CUSTOMER S INABILITY TO USE THE COVERED PRODUCT, EVEN IF TURNSTILES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to a particular purchaser. This Limited Warranty gives the purchaser specific legal rights. The purchaser may also have other rights, which vary from state to state. Pg 029

30 8641S.WarhawkRd.Conifer,CO (303) (303) fax