GENERAL SPECIFICATIONS FOR:

Transcription

1 GENERAL SPECIFICATIONS FOR: FUEL FILTRATION SYSTEMS 5A, 8A, 10A, 15A, 20A, 30A, &40A Equipment manufactured in the U.S.A. All specifications subject to change. Version 3.1

2 5A MODEL GENERAL SPECIFICATIONS v3.1 UltraPure 2

3 General Specification for Ultrapure Automatic Fuel Maintenance & Conditioning System 5A Model Input power requirement: 120/240V 1-phase, 208/480V 3-phase Rated flow rate: 5 GPM / 300 GPH (19 L/min) Designed for a 3,000gal (11,356L) diesel fuel storage facility 1. Control 1.1. Model 5A is controlled by PLC micro-processor Controller to be UL, cul and CE recognized Control unit will have a long life battery back-up system to provide software integrity during prolonged power loss, shipping and maintenance cycles All software is to be factory loaded prior to shipment and a permanent copy of each customer s software is to be maintained at the manufacture s location Software updates are to be provided through out equipment life time Digital 2 line LCD display interface for all user defined programming PIN code protection for user functions PLC has user selectable remote communication capabilities PLC memory shall maintain an event log with error review and tracking Power save mode to conserve power and extend unit life /120 volt control system. 2. Monitoring The following minimum functions will be monitored by the Ultrapure PLC: 2.1. Utility power available Door open/close Cycle table High Pressure Low Pressure Pump status Generator interlock Filter Status with automatic notification feature Water level Filter leak Pump leak Retention basin full Motor overload Exterior status lights Two dry contacts for facility interface i.e. Tank over-flow i.e. Tank leak detector v3.1 UltraPure 3

4 3. Filtration Ultrapure Model 5A is designed to maintain stored fuel to meet or exceed ASTM (D)975 using the following seven stage filtration Coalescence 3.2. Bulk water removal mesh filtration 3.4. Entrained water removal micron filtration 3.6. Emulsified water removal micron filtration 4. Conditioning 4.1. An additional propriety magnetic fuel conditioning element is to be provided as a system standard. 5. Mechanical features 5.1. Unit is of rigid steel construction Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment Double compartment containment vessel /4 HP pump motor ½ NPT plumbing inlet and outlet Double restrained hose and valve connections. 6. Multi-tank manifold (Optional) An optional multi-tank manifold shall be housed in a separate outdoor enclosure designed to match the 5A automatic fuel maintenance and conditioning system Each solenoid valve in the manifold is controlled by the 10A PLC Software will provide redundant failsafe operation for proper solenoid sequencing Double compartment containment vessel ¾ NPT plumbing inlets and outlets Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment. v3.1 UltraPure 4

5 8A MODEL GENERAL SPECIFICATIONS v3.1 UltraPure 5

6 General Specification for Ultrapure Automatic Fuel Maintenance & Conditioning System 8A Model Input power requirement: 120/240V 1-phase, 208/480V 3-phase Rated flow rate: 8 GPM / 480 GPH (30 L/min) Designed for a 10,000 gal (37,854 L) diesel fuel storage facility. 1. Control 1.1. Model 8A is controlled by PLC micro-processor Controller to be UL, cul and CE recognized Control unit will have a long life battery back-up system to provide software integrity during prolonged power loss, shipping and maintenance cycles All software is to be factory loaded prior to shipment and a permanent copy of each customer s software is to be maintained at the manufacture s location Software updates are to be provided through out equipment life time Digital 2 line LCD display interface for all user defined programming PIN code protection for user functions PLC has user selectable remote communication capabilities PLC memory shall maintain an event log with error review and tracking Power save mode to conserve power and extend unit life /120 volt control system. 2. Monitoring The following minimum functions will be monitored by the Ultrapure PLC: 2.1. Utility power available Door open/close Cycle table High Pressure Low Pressure Pump status Generator interlock Filter Status with automatic notification feature Water level Filter leak Pump leak Retention basin full Motor overload Exterior status lights Two dry contacts for facility interface i.e. Tank over-flow i.e. Tank leak detector v3.1 UltraPure 6

7 3. Filtration Ultrapure Model 8A is designed to maintain stored fuel to meet or exceed ASTM (D)975 using the following seven stage filtration Coalescence 3.2. Bulk water removal mesh filtration 3.4. Entrained water removal micron filtration 3.6. Emulsified water removal micron filtration 4. Conditioning 4.1. An additional propriety magnetic fuel conditioning element is to be provided as a system standard. 5. Mechanical features 5.1. Unit is of rigid steel construction Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment Double compartment containment vessel /4 HP pump motor ½ NPT plumbing inlet and outlet Double restrained hose and valve connections. 6. Multi-tank manifold (Optional) An optional multi-tank manifold shall be housed in a separate outdoor enclosure designed to match the 8A automatic fuel maintenance and conditioning system Each solenoid valve in the manifold is controlled by the 10A PLC Software will provide redundant failsafe operation for proper solenoid sequencing Double compartment containment vessel ¾ NPT plumbing inlets and outlets Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment. v3.1 UltraPure 7

8 10A MODEL GENERAL SPECIFICATIONS v3.1 UltraPure 8

9 General Specification for Ultrapure Automatic Fuel Maintenance & Conditioning System 10A Model Input power requirement: 120/240V 1-phase, 208/480V 3-phase Rated flow rate: 10 GPM / 600 GPH (38 L/min) Designed for a 20,000 gal (75708 L) diesel fuel storage facility. 1. Control 1.1. Model 10A is controlled by PLC micro-processor Controller to be UL, cul and CE recognized Control unit will have a long life battery back-up system to provide software integrity during prolonged power loss, shipping and maintenance cycles All software is to be factory loaded prior to shipment and a permanent copy of each customer s software is to be maintained at the manufacture s location Software updates are to be provided through out equipment life time Digital 2 line LCD display interface for all user defined programming PIN code protection for user functions PLC has user selectable remote communication capabilities PLC memory shall maintain an event log with error review and tracking Power save mode to conserve power and extend unit life /120 volt control system. 2. Monitoring The following minimum functions will be monitored by the Ultrapure PLC: 2.1. Utility power available Door open/close Cycle table High Pressure Low Pressure Pump status Generator interlock Filter Status with automatic notification feature Water level Filter leak Pump leak Retention basin full Motor overload Exterior status lights Two dry contacts for facility interface i.e. Tank over-flow i.e. Tank leak detector v3.1 UltraPure 9

10 3. Filtration Ultrapure Model 10A is designed to maintain stored fuel to meet or exceed ASTM (D)975 using the following seven stage filtration Coalescence 3.2. Bulk water removal mesh filtration 3.4. Entrained water removal micron filtration 3.6. Emulsified water removal micron filtration 4. Conditioning 4.1. An additional propriety magnetic fuel conditioning element is to be provided as a system standard. 5. Mechanical features 5.1. Unit is of rigid steel construction Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment Double compartment containment vessel HP pump motor ¾ NPT plumbing inlet and outlet Double restrained hose and valve connections. 6. Multi-tank manifold (Optional) An optional multi-tank manifold shall be housed in a separate outdoor enclosure designed to match the 10A automatic fuel maintenance and conditioning system Each solenoid valve in the manifold is controlled by the 10A PLC Software will provide redundant failsafe operation for proper solenoid sequencing Double compartment containment vessel ¾ NPT plumbing inlets and outlets Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment. v3.1 UltraPure 10

11 15A MODEL GENERAL SPECIFICATIONS v3.1 UltraPure 11

12 General Specification for Ultrapure Automatic Fuel Maintenance & Conditioning System 15A Model Input power requirement: 120/240V 1-phase, 208/480V 3-phase Rated flow rate: 15 GPM / 900 GPH (58 L/min) Designed for a 30,000 gal (113,562 L) diesel fuel storage facility 1. Control 1.1. Model 15A is controlled by PLC micro-processor Controller to be UL, cul and CE recognized Control unit will have a long life battery back-up system to provide software integrity during prolonged power loss, shipping and maintenance cycles All software is to be factory loaded prior to shipment and a permanent copy of each customer s software is to be maintained at the manufacture s location Software updates are to be provided through out equipment life time Digital 2 line LCD display interface for all user defined programming PIN code protection for user functions PLC has user selectable remote communication capabilities PLC memory shall maintain an event log with error review and tracking Power save mode to conserve power and extend unit life /120 volt control system. 2. Monitoring The following minimum functions will be monitored by the Ultrapure PLC: 2.1. Utility power available Door open/close Cycle table High Pressure Low Pressure Pump status Generator interlock Filter Status with automatic notification feature Water level Filter leak Pump leak Retention basin full Motor overload Exterior status lights Two dry contacts for facility interface i.e. Tank over-flow i.e. Tank leak detector v3.1 UltraPure 12

13 3. Filtration Ultrapure Model 15A is designed to maintain stored fuel to meet or exceed ASTM (D)975 using the following seven stage filtration Coalescence 3.2. Bulk water removal mesh filtration 3.4. Entrained water removal micron filtration 3.6. Emulsified water removal micron filtration 4. Conditioning 4.1. An additional propriety magnetic fuel conditioning element is to be provided as a system standard. 5. Mechanical features 5.1. Unit is of rigid steel construction Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment Double compartment containment vessel HP pump motor ¾ NPT plumbing inlet and outlet Double restrained hose and valve connections. 6. Multi-tank manifold (Optional) An optional multi-tank manifold shall be housed in a separate outdoor enclosure designed to match the 15A automatic fuel maintenance and conditioning system Each solenoid valve in the manifold is controlled by the 10A PLC Software will provide redundant failsafe operation for proper solenoid sequencing Double compartment containment vessel ¾ NPT plumbing inlets and outlets Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment. v3.1 UltraPure 13

14 20A MODEL GENERAL SPECIFICATIONS v3.1 UltraPure 14

15 General Specification for Ultrapure Automatic Fuel Maintenance & Conditioning System 20A Model Input power requirement: 120/240V 1-phase, 208/480V 3-phase Rated flow rate: 20 GPM / 1200 GPH (76 L/min) Designed for a 40,000 gal (151,416 L) diesel fuel storage facility 1. Control 1.1. Model 20A is controlled by PLC micro-processor Controller to be UL, cul and CE recognized Control unit will have a long life battery back-up system to provide software integrity during prolonged power loss, shipping and maintenance cycles All software is to be factory loaded prior to shipment and a permanent copy of each customer s software is to be maintained at the manufacture s location Software updates are to be provided through out equipment life time Digital 2 line LCD display interface for all user defined programming PIN code protection for user functions PLC has user selectable remote communication capabilities PLC memory shall maintain an event log with error review and tracking Power save mode to conserve power and extend unit life /120 volt control system. 2. Monitoring The following minimum functions will be monitored by the Ultrapure PLC: 2.1. Utility power available Door open/close Cycle table High Pressure Low Pressure Pump status Generator interlock Filter Status with automatic notification feature Water level Filter leak Pump leak Retention basin full Motor overload Exterior status lights Two dry contacts for facility interface i.e. Tank over-flow i.e. Tank leak detector v3.1 UltraPure 15

16 3. Filtration Ultrapure Model 20A is designed to maintain stored fuel to meet or exceed ASTM (D)975 using the following seven stage filtration Coalescence 3.2. Bulk water removal mesh filtration 3.4. Entrained water removal micron filtration 3.6. Emulsified water removal micron filtration 4. Conditioning 4.1. An additional propriety magnetic fuel conditioning element is to be provided as a system standard. 5. Mechanical features 5.1. Unit is of rigid steel construction Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment Double compartment containment vessel HP pump motor NPT plumbing inlet and outlet Double restrained hose and valve connections. 6. Multi-tank manifold (Optional) An optional multi-tank manifold shall be housed in a separate outdoor enclosure designed to match the 20A automatic fuel maintenance and conditioning system Each solenoid valve in the manifold is controlled by the 10A PLC Software will provide redundant failsafe operation for proper solenoid sequencing Double compartment containment vessel NPT plumbing inlets and outlets Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment. v3.1 UltraPure 16

17 30A MODEL GENERAL SPECIFICATIONS v3.1 UltraPure 17

18 General Specification for Ultrapure Automatic Fuel Maintenance & Conditioning System 30A Model Input power requirement: 208/480V 3-phase Rated flow rate: 30 GPM / 1800 GPH (114 L/min) Designed for a 60,000 gal (227,125 L) diesel fuel storage facility 1. Control 1.1. Model 30A is controlled by PLC micro-processor Controller to be UL, cul and CE recognized Control unit will have a long life battery back-up system to provide software integrity during prolonged power loss, shipping and maintenance cycles All software is to be factory loaded prior to shipment and a permanent copy of each customer s software is to be maintained at the manufacture s location Software updates are to be provided through out equipment life time Digital 2 line LCD display interface for all user defined programming PIN code protection for user functions PLC has user selectable remote communication capabilities PLC memory shall maintain an event log with error review and tracking Power save mode to conserve power and extend unit life /120 volt control system. 2. Monitoring The following minimum functions will be monitored by the Ultrapure PLC: 2.1. Utility power available Door open/close Cycle table High Pressure Low Pressure Pump status Generator interlock Filter Status with automatic notification feature Water level Filter leak Pump leak Retention basin full Motor overload Exterior status lights Two dry contacts for facility interface i.e. Tank over-flow i.e. Tank leak detector v3.1 UltraPure 18

19 3. Filtration Ultrapure Model 30A is designed to maintain stored fuel to meet or exceed ASTM (D)975 using the following seven stage filtration Coalescence 3.2. Bulk water removal mesh filtration 3.4. Entrained water removal micron filtration 3.6. Emulsified water removal micron filtration 4. Conditioning 4.1. An additional propriety magnetic fuel conditioning element is to be provided as a system standard. 5. Mechanical features 5.1. Unit is of rigid steel construction Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment Double compartment containment vessel HP pump motor ¼ NPT plumbing inlet and outlet Double restrained hose and valve connections. 6. Multi-tank manifold (Optional) An optional multi-tank manifold shall be housed in a separate outdoor enclosure designed to match the 30A automatic fuel maintenance and conditioning system Each solenoid valve in the manifold is controlled by the 10A PLC Software will provide redundant failsafe operation for proper solenoid sequencing Double compartment containment vessel ¼ NPT plumbing inlets and outlets Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment. v3.1 UltraPure 19

20 40A MODEL GENERAL SPECIFICATIONS v3.1 UltraPure 20

21 General Specification for Ultrapure Automatic Fuel Maintenance & Conditioning System 40A Model Input power requirement: 208/480V 3-phase Rated flow rate: 40 GPM / 2400 GPH (151 L/min) Designed for a 80,000 gal (302,833 L) diesel fuel storage facility 1. Control 1.1. Model 40A is controlled by PLC micro-processor Controller to be UL, cul and CE recognized Control unit will have a long life battery back-up system to provide software integrity during prolonged power loss, shipping and maintenance cycles All software is to be factory loaded prior to shipment and a permanent copy of each customer s software is to be maintained at the manufacture s location Software updates are to be provided through out equipment life time Digital 2 line LCD display interface for all user defined programming PIN code protection for user functions PLC has user selectable remote communication capabilities PLC memory shall maintain an event log with error review and tracking Power save mode to conserve power and extend unit life /120 volt control system. 2. Monitoring The following minimum functions will be monitored by the Ultrapure PLC: 2.1. Utility power available Door open/close Cycle table High Pressure Low Pressure Pump status Generator interlock Filter Status with automatic notification feature Water level Filter leak Pump leak Retention basin full Motor overload Exterior status lights Two dry contacts for facility interface i.e. Tank over-flow i.e. Tank leak detector v3.1 UltraPure 21

22 3. Filtration Ultrapure Model 40A is designed to maintain stored fuel to meet or exceed ASTM (D)975 using the following seven stage filtration Coalescence 3.2. Bulk water removal mesh filtration 3.4. Entrained water removal micron filtration 3.6. Emulsified water removal micron filtration 4. Conditioning 4.1. An additional propriety magnetic fuel conditioning element is to be provided as a system standard. 5. Mechanical features 5.1. Unit is of rigid steel construction Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment Double compartment containment vessel HP pump motor ½ NPT plumbing inlet and outlet Double restrained hose and valve connections. 6. Multi-tank manifold (Optional) An optional multi-tank manifold shall be housed in a separate outdoor enclosure designed to match the 40A automatic fuel maintenance and conditioning system Each solenoid valve in the manifold is controlled by the 10A PLC Software will provide redundant failsafe operation for proper solenoid sequencing Double compartment containment vessel ½ NPT plumbing inlets and outlets Outdoor rain and drip proof enclosure Hinged enclosure door with handle and gasket Durable powedercoat finish Mounting legs for ease of floor attachment. v3.1 UltraPure 22

23 WARRANTY FOR ULTRAPURE FUEL FILTERING, ECOPURE FUEL BLENDING, AND TRANSPURE INSULATING OIL CLEANING SYSTEMS This guarantee is extended only to the original purchaser, or if the purchaser is a reseller, the first customer they sell the equipment to, and will not be honored for any subsequent owner, user or transferee of this EQUIPMENT without obtaining written consent from Clinton Nevada, LLC. Clinton UltraPure will make every effort to fill orders within the time stated, but under no circumstances will Clinton Nevada, LLC be responsible for, or purchaser entitled to, any damages arising out of or owing to any delays whatsoever in shipment, delivery or installation. All electrical and mechanical components of each ECOPURE automatic fuel blender are guaranteed against defects in material & workmanship for a period of ONE YEAR from date of shipment provided all installation and operating instructions furnished with unit are adhered to. ULTRAPURE S liability shall be limited to repairing or replacing fob UltraPure s North Las Vegas Nevada plant, or allowing an equivalent credit at Clinton Nevada LLC s option for any part or parts, or material which may prove to be defective, provided the buyer gives Clinton Nevada prompt notice of the defect, and inspection, if required by Clinton Nevada, confirms such defect or defects. In no event will Clinton Nevada be liable for removal or reinstallation of any such part or parts and any costs incurred therewith. This remedy of repair, replacement or credit, at Clinton Nevada LLC s option, is the exclusive remedy hereunder. Clinton Nevada, LLC shall have no other liability to purchaser or any claims however arising and in no event shall Clinton Nevada, LLC be liable for general, special, incidental, consequential, or contingent damages under any warranty, express or implied, and all such liability is herby expressly excluded. Clinton Nevada, LLC makes no warranties, express or implied, of merchantability, fitness for a particular purpose or otherwise, with respect to the products covered by this warranty policy, except as expressly provided for herein. No employee, agent or distributor is authorized to make any warranty on behalf of Clinton Nevada, LLC. Clinton Nevada LLC s warranty does not cover minor leaks or drips, ordinary wear & tear, abuse, misuse, overloading, alterations, expendable parts & parts coming into abnormal contact with corrosive chemicals, fumes, moisture, or damage caused by factors beyond Clinton Nevada LLC s control. Clinton Nevada, LLC s failure to enforce any provision hereof shall not imply a waiver of that or any other provision. v3.1 UltraPure 23