Product Campaign Bulletin

Transcription

1 Nissan Ireland Cedar House Park West Business Park Nangor Road, Dublin 12 Product Campaign Bulletin REFERENCE: MODEL: PCB-NES Maxima (A36), Pulsar (C13), Juke (F15), Qashqai (J11) and X-Trail (T32) SUBJECT: PCB T32 - R Rear Oxygen Sensor On-Board Diagnosis

2 REPAIR PROCESS REPAIR PROCESS - Rear Oxygen Sensor On-Board Diagnosis Dealer checks VIN in enews YES Dealer confirms if vehicle is affected by campaign NO Dealer performs repair procedure R16200 No further action required Dealer submits claim

3 Precautions <Condition of the vehicle> Erase all recorded DTC in the vehicle before reprogramming. Turn off all the electric loads. Do NOT use mobile phone or devices that emit electromagnetic waves, such as radio transceivers etc., near the vehicle. Connect battery charger/stabilizer to the 12V battery and control the output to maintain the voltage always within 12V to 13.5V. Ensure all doors are closed and the driver's window is in the fully down position. During the reprogramming do not switch OFF the ignition. If the engine has been running, ensure the ignition is OFF for at least 30 seconds to allow time for the ECM to reset before conducting the rework. <Condition of Consult IIIplus> Be sure to have the AC Adapter to your Consult IIIplus connected, during the reprogramming. Switch off screen saver of your Consult IIIplus Connect VI with USB cable, and do not disconnect during the reprogramming. If further reprogram is to be conducted for another vehicle after completion of the reprogram, turn off Consult IIIplus completely before continuing. Make sure to use Ver.61.1 or later version of Consult IIIplus software. Make sure the relevant Consult IIIplus patch for this activity is installed. OVERVIEW OF AFFECTED AREA v X-trail (T32) Pulsar (C13) Maxima (A36) v v v Qashqai (J11) Juke (F15) Engine Control Module (ECM)

4 REPAIR PROCEDURE 1 Connect 12V battery charger/stabilizer to the vehicle battery. NOTE: Make sure all the key points in the precautions section are followed. Connect exhaust extraction unit to vehicle exhaust. 2 Connect the VI Unit to the vehicle port and to Consult IIIplus using USB connection. Note:- Note depending on the model it may be necessary to remove a cover prior to allow the VI Unit connection. 3 Change the vehicle condition to "ON", by operating the ignition switch. 4 Start up Consult IIIplus and confirm that the VI is connected to the vehicle and to Consult IIIplus by USB connection.

5 5 Click on "Diagnosis (All Systems)" and select the appropriate vehicle to be reprogrammed. 6 Check that there are no DTCs recorded or solve/erase all recorded DTCs before continuing. 7 Click on "Home" button and then "Diagnosis (One System)" 8 Click on "Engine" button and check there are no DTCs recorded.

6 9 Select "ECU Identification" tab. NOTE: find below table with affected ECU IDs, if the vehicle is within the affected VIN list but the ECU Identification is not included in this table, contact Technical Support Department. Compatibility table correct at the time of bulletin release F15 Vehicle Specification F15_2014_MR16DDT_E-OBD_ASR_CVT_4WD F15_2014_MR16DDT_E-OBD_ASR_MT_2WD F15_2014_MR16DDT_E-OBD_EUR_CVT_4WD F15_2014_MR16DDT_E-OBD_EUR_MT_2WD F15_2014_MR16DDT_E-OBD_SAF_CVT_4WD F15_2014_MR16DDT_E-OBD_SAF_MT_2WD F15_2014_MR16DDT_E-OBD_TWN_CVT_4WD NG Software BV84A BV84B BV84C BV83A BV83B BV83C BV83D TW1A BV82A BV82D BV81A BV81C BV81D BV81E BV86A BV86B BV86C BV85A BV85B BV85C BV85D BV88A BV88B BV88C Countermeasure TW0A BV83E TW1B TW8A TW9A BV85E BV88D A36 Vehicle Specification NG Software Countermeasure A36_16MY_VQ35DE_ISR_CVT_2WD_2WD_VDC_ASCD_AUC RJ0A RJ4A A36_16MY_VQ35DE_ISR_CVT_2WD_2WD_VDC_ASCD_IDM RJ1A RJ5A A36_16MY_VQ35DE_ISR_CVTQLU_2WD_2WD_VDC_ASCD_AUC RJ0B RJ0C RJ0D A36_16MY_VQ35DE_ISR_CVTQLU_2WD_2WD_VDC_ASCD_IDM RJ1B RJ1C RJ1D C13 Vehicle Specification C13_2014_MR16DDT_E-OBD_EUR_MT_2WD_ISS_2WD C13_2014_MR16DDT_E-OBD_EUR_MT_2WD_ISS_2WD_FEB NG Software ZM1A ZM1B ZM1C ZM1D ZM2A ZM2B ZM2C ZM2D Countermeasure ZM1E ZM2E

7 T32_2015_MR16DDT_E-OBD_EUR_MT_2WD_ISS_2WD_ASCD_FEB MS5A MS2A MS2B MS2C MS2D MS2E MS5A T32_2015_MR16DDT_E-OBD_EUR_MT_2WD_ISS_2WD_ASCD MS4A MS1A MS1B MS1C MS1D MS1E MS4A T32 Vehicle Specification NG Software Countermeasure T32_2015_MR16DDT_E-OBD_EUR_MT_2WD_ISS_2WD MS3A MS0A MS0B MS0C MS0D MS0E MS3A J11_2014_MR16DDT_E-OBD_SAF_MT_2WD_ISS_2WD_ASCD BD83B BD74A BD74B BD74C BD74D BD74E BD83A BD83B J11_2014_MR16DDT_E-OBD_EUR_MT_2WD_ISS_2WD_ASCD_ASL_G/S_HFS_FEB BD85B BD76A BD76B BD76C BD76D BD76E BD85A BD85B BD81B J11_2014_MR16DDT_E-OBD_EUR_MT_2WD_ISS_2WD_ASCD_ASL_G/S_HFS BD82B BD73A BD73B BD73C BD73D BD73E BD82A BD82B J11_2014_MR16DDT_E-OBD_EUR_MT_2WD_ISS_2WD_ASCD_ASL_G/S_FEB J11 Vehicle Specification NG Software Countermeasure J11_2014_MR16DDT_E-OBD_EUR_MT_2WD_ISS_2WD_ASCD_ASL_G/S BD81B BD72A BD72B BD84B BD75A BD75B BD75C BD75D BD75E BD84A BD84B BD72C BD72D BD72E BD81A

8 10 Click on "Home" button and then "Re/programming, Configuration" 11 Read and follow the precautions and tick the confirmation check box, then click on "Next". NOTE: Any precautions added in Consult IIIplus after the release of this bulletin must also be followed. 12 Select the appropriate vehicle to be reprogrammed, click on "Select" and then click "Confirm". Enter the VIN number and click on "Confirm". NOTE: VIN should be automatically identified, insert it manually otherwise.

9 13 Click on "Engine" button. Then click on the "Reprogramming" button. 14 Check that the part number shown is included in the table in step 9 and touch the Save button. Then click on "Next" button. 15 Read both precaution pages, tick the confirmation check box and click on "Next". NOTE: Any precautions added in Consult IIIplus after the release of this bulletin must also be followed.

10 16 Confirm that the Part number after reprogramming is according to the table in section 9 and click "Next". NOTE: table in section 9 shows compatibility at the release of the campaign, any later ECM Part Number update (unrelated to the campaign) will not be included in this table. 17 Confirm output of the charger/stabilizer result is OK and click on "Next". 18 Confirm the reprogramming conditions in the table are met and click on "Start". 19 Wait until "Transfer VI to ECU" is 100% and then click "Next". NOTE: follow all the indications in the precautions sections, failing to do so may result in damage to the vehicle. Refer to the "Troubleshooting" section at the end of this document.

11 20 Operate the ignition switch to OFF status and wait for the system to update the status to OFF. Then operate the ignition switch to ON. 21 The Idle air volume learning page will appear. Start engine and then select next. Monitor engine coolant temperature until it reaches 70 Deg C. Once the temperature is achieved select start and current status will change to executing. 22 If the temperature condition was incorrect the coolant temperature will indicate NG. Select retry and continue as per section 21. Having selected start or retry the current status will indicate completed if the operation has been successful. Select next. 23 The accelerator pedal closed position page will appear. Follow the ignition on off sequence as directed by the consult screen.

12 24 Start engine and confirm engine operation is normal. Select next. 25 Switch ignition off an the on as instructed. Then select next. 26 Confirm ECU part corresponds to as expected (Reference table section 9) 27 Click "Home" button and click on "Diagnosis (All Systems)". Check that there are no DTCs recorded or solve/erase all recorded DTCs before continuing. 28 Disconnect battery charger and exhaust extractor. Remove VI unit and refit cover, if necessary. Procedure Complete

13 TROUBLESHOOTING More than one Part Number option is shown for reprogramming Use Part Number after reprogramming and Other information to select the correct option for the affected vehicle. Tables are given within the repair procedure to ensure PN information is available. No option is shown for reprogramming or the reprogramming button is not active Make sure the reprogramming patch has been correctly installed following the instructions at the end of the procedure. Make sure the Part Number of the unit is affected by the activity. An error message is shown when transfering data to the control unit Make sure all items in the precaution section are followed. Failing to do so may result in permanent damage to the control unit. Contact your NSC Technical Assistance Department. NOTE: if the control unit is no longer detected by Consult IIIplus permanent damage may have been caused to the control unit and replacement may be necessary.

14 HOW TO CHECK Consult IIIplus VERSION The software version can be checked on the top left corner of the screen of Consult IIIplus. HOW TO DOWNLOAD & INSTALL THE REPROGRAMMING PATCH 1 Log into N-FIT on the B2B portal, then select the Programming/Reprogramming data search option in the left window pane. 2 The required software located on N-fit as shown below Note:- The model sellection can be any of the models affected A36, C13, F15, J11 or T32 3 Select the following file Subject: R1620_ECM_A36 C13 F15 J11 T32_MR16DDT VQ35DE Data Type: Campaign Reprogramming data Released: 30/06/2016

15 4 Save and execute the files with Consult IIIplus closed. 5 Select the preferred language then click OK, Next and Install. 6 Click on finish when installed. COMMON ACRONYMS USED IN THE REPROGRAMMING PATCH Acronym Explanation Acronym Explanation EU /EUR Europe BLNK Blank RUS Russia REPR Reprogramming UKR Ukraine wdpf With DieselParticulateFilter MOR Morocco w/odpf Without DieselParticulateFilter GOM General Overseas Market STD Standard version SAF South Africa ECO Eco version JPN Japan AT Automatic transmission NAM North America M/T (MT) Manual transmission KOR Koreea SL Speed limiter ASR (AUS) Australia XXXkw Engine power XXXKW XXMY ( MYXX ) Model year 20XX 2WD 2 wheels drive E5 EURO 5 emission standard 4WD 4 wheels drive LCV 4 /5 Light commercial vehicle ASCD Optional With ASCD cruise ( control can be present and with or speed not, limiter or installed LT Light Truck tire ( e.g. D40 YD25 model) oascd after) ISS Intelligent Start Stop H/Usw Heat up switch 3row/2row 7 seats /5 seats T/C Turbocharger Inj.PumpDFP3.4/Inj. PumpDFP1.15 High pressure fuel pump type (3.4, 1.15) Single mass/double mass F/W Single mass/double mass flywheel wvdc With VDC (ESP) / VDCS ICC Intelligent cruise control w/ovdc Without VDC (ESP) / VDCS