VO LUNTARY SERVIC E C AMPAIG N

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "VO LUNTARY SERVIC E C AMPAIG N"

Transcription

1 2013 Sorento Report a problem with this article GROUP Service Campaign NUMBER MODEL 2011~13MY Sorento (XMa) DATE SC106 May 2014 VO LUNTARY SERVIC E C AMPAIG N This bulletin provides information related to an upgrade of the ECM software on some 2011~2013MY Sorento (XMa) vehicles, produced from July 12, 2010 through January 31, During a specific set of operating conditions, it is possible under rare circumstances when braking and bringing the vehicle to a stop, for the engine to also stop. Although the engine can be restarted immediately, to ensure maximum customer satisfaction, Kia is requesting the completion of this Service Campaign on all affected 2011~2013MY Sorento (XMa) vehicles. To prevent this condition, verify ROM ID using the tables in this TSB and update the ECM, as necessary. Global Diagnostic System (GDS) To assure complete customer satisfaction, always remember to refer to WebDCS Warranty Coverage (validation) Inquiry Screen (Service > Warranty Coverage >Warranty Coverage Inquiry) for a list of any additional campaigns that may need to be performed on the vehicle before returning it to the customer. File Under: < Service Campaign > x x x Circulate To: General Manager Service Manager Parts Manager x Service Advisor(s) x Technician(s) x Body Shop Manager x Fleet Repair https://www.motologic.com/car/2013_sorento_xm/article/a088d1-a9a3cf59445f0c6d65580ff562c5b6a0960e5dfc0?returnpath=%2fcar%2f2013_sorent 1/9

2 Page 2 of 9 ECM Upgrade Procedure: To correct this condition, the ECM should be reprogrammed using the GDS Download, as described in this bulletin. UPGRADE EVENT NAME 229.XMA 3.5 RPM LOGIC IMPROVEMENT(ECU) A fully charged battery is necessary before ECM upgrade can take place. It is recommended that the Midtronics GR system be used in ECM mode during charging. DO NOT connect any other battery charger to the vehicle during ECM upgrade. All ECM upgrades must be done with the ignition key in the ON position. Be careful not to disconnect any cables connected to the vehicle or GDS during the ECM upgrade procedure DO NOT start the engine during ECM upgrade. DO NOT turn the ignition key OFF or interrupt the power supply during ECM upgrade. When the ECM upgrade is completed, turn the ignition OFF and wait 20 seconds before starting the engine. ONLY use approved ECM upgrade software designated for the correct model, year. CAUTION Before attempting an ECM upgrade on any Kia model, make sure to first determine whether the particular model is equipped with an immobilizer security system. Failure to follow proper procedures may cause the PCM to become inoperative after the upgrade and any claims associated with this repair may be subject to chargeback. https://www.motologic.com/car/2013_sorento_xm/article/a088d1-a9a3cf59445f0c6d65580ff562c5b6a0960e5dfc0?returnpath=%2fcar%2f2013_sorent 2/9

3 Page 3 of 9 ROM ID INFORMATION TABLES : Upgrade Event #229 Sorento (XMa) MODEL IMMO ECM P/N ECM ROM ID PREVIOUS NEW XMAN35*M2**AB6A* XMAN35*M2**AB6B* XMAN35*M2**AB6C* XMAN35*M2**AB6D* XMAN35*M2**AD1DS XMAN35*M2**AB8GZ XMAN35*M2**AD1BS Yes C010 XMAN35*M2**AB8B* (+) XMAN35*M2**AB8D* XMAN35*M2**AB8E* XMAN35*M2**AB8G* XMAN35*M2**AD1CS XMAN35*M2**AB8F* XMAN35*M2**AD0AS XM XMAN35*M2**AD1AS 3.5L XMAN35*S2**AB6A* (11MY) XMAN35*S2**AB6B* XMAN35*S2**AB6C* XMAN35*S2**AB6D* XMAN35*S2**AD1DS XMAN35*S2**AB8GZ XMAN35*S2**AD1BS No (-) C060 XMAN35*S2**AB8B* XMAN35*S2**AB8D* XMAN35*S2**AB8G* XMAN35*S2**AB8E* XMAN35*S2**AD1CS XMAN35*S2**AB8F* XMAN35*S2**AD0AS XMAN35*S2**AD1AS XM 3.5L (12MY) XM 3.5L (13MY) XMBN35*M2**AC3A* XMCN35*M2**AC6B* C011 XMBN35*M2**AC4A* Yes XMBN35*M2**AC4B* (+) XMBN35*M2**AD0AS XMBN35*M2**AD1AS XMBN35*M2**AD1BS XMBN35*S2**AC3A* XMBN35*S2**AC4B* No (-) C061 XMCN35*S2**AC6B* XMBN35*S2**AC4A* XMBN35*S2**AD1BS XMBN35*S2**AD0AS XMBN35*S2**AD1AS Yes (+) XMCN35*M2**AC4A* C012 XMCN35*M2**AC6A* XMCN35*M2**AD0AS XMCN35*M2**AD1BS XMCN35*M2**AD1AS XMCN35*S2**AC4A* No (-) C062 XMCN35*S2**AC6A* XMCN35*S2**AD0AS XMCN35*S2**AD1BS XMCN35*S2**AD1AS To verify the vehicle is affected, be sure to check the Calibration Identification of the vehicle's ECM ROM ID and reference the Information Table as necessary. https://www.motologic.com/car/2013_sorento_xm/article/a088d1-a9a3cf59445f0c6d65580ff562c5b6a0960e5dfc0?returnpath=%2fcar%2f2013_sorent 3/9

4 Page 4 of 9 1. Connect the power supply cable to the GDS. If attempting to perform the ECM upgrade with the power supply cable disconnected from the GDS, be sure to check that the GDS is fully charged before ECM upgrade. If the GDS is not fully charged, failure to perform the ECM upgrade may occur. Therefore, it is strongly recommended that the power supply connector be connected to the GDS. 2. Connect the USB cable between the VCI and the GDS. When performing the ECM upgrade using the GDS, wireless communication between the VCI and GDS is not available. Therefore, be sure to connect the USB cable between the VCI and the GDS. 3. Connect the Main 16-pin DLC cable (GHDM ) to the VCI. 4. Connect the Main 16-pin DLC cable (GHDM ) to the OBD-II connector, located under the driver's side of the instrument panel. 5. With the ignition key ON, turn ON the VCI and GDS. Access the GDS vehicle identification number (VIN) screen and configure the vehicle using the VIN AUTO DETECT Function. 6. Select ENGINE system and click OK. https://www.motologic.com/car/2013_sorento_xm/article/a088d1-a9a3cf59445f0c6d65580ff562c5b6a0960e5dfc0?returnpath=%2fcar%2f2013_sorent 4/9

5 3/9/2018 CAMPAIGN Engine Electrical System [SC106]Service Campaign: ECM Logic Upgrade Sorento (XMa) 3.5L MPI (SC 106) 2013 Kia Sorento Page 5 of 9 7. Select ECU Upgrade. 8. Select Auto Mode, and then Next. 9. Select Engine and click OK. https://www.motologic.com/car/2013_sorento_xm/article/a088d1-a9a3cf59445f0c6d65580ff562c5b6a0960e5dfc0?returnpath=%2fcar%2f2013_sorent 5/9

6 Page 6 of Select Upgrade Event: Upgrade Event #229.XMA 3.5 RPM LOGIC IMPROVEMENT(ECU), then click Upgrade button and OK on battery voltage check screen. 11. Upgrade will begin and the progress of the upgrade will appear on the bar graph. 12. Follow the guidelines displayed on the screen during upgrade procedure and make sure to cycle the ignition OFF ON for 10 seconds. https://www.motologic.com/car/2013_sorento_xm/article/a088d1-a9a3cf59445f0c6d65580ff562c5b6a0960e5dfc0?returnpath=%2fcar%2f2013_sorent 6/9

7 Page 7 of Click OK on the final screen. Upgrade event 229 is now complete. 14. Check if any incidental Diagnostic Trouble Codes DTC(s) have been created by the upgrade process; clear any DTC(s) that may be present. 15. Start the engine to confirm proper operation of the vehicle. CAUTION Before attempting an ECM upgrade on any Kia model, make sure to first determine whether the particular model is equipped with an immobilizer security system. Failure to follow proper procedures may cause the PCM to become inoperative after the upgrade and any claims associated with this repair may be subject to chargeback. Do NOT attempt to perform a Manual Mode upgrade unless Auto Mode fails. Always follow the instructions given on the GDS in either Auto or Manual mode. See table for Manual Mode passwords. https://www.motologic.com/car/2013_sorento_xm/article/a088d1-a9a3cf59445f0c6d65580ff562c5b6a0960e5dfc0?returnpath=%2fcar%2f2013_sorent 7/9

8 Page 8 of 9 * MANUAL MODE ECM UPGRADE PASSWORDS: * Do NOT perform Manual Mode ECM upgrade unless Auto Mode fails. Upgrade Event #229 Sorento (XMa) MENU PASSWORD XMA 11MY 3.5 +IMMO/SMK : C010[B6A*~B8GZ/D1BS] 3010 XMA 11MY 3.5 +IMMO/SMK : C010[B8B*~B8F*/D1AS] 3011 XMA 12MY 3.5 +IMMO/SMK : C XMA 13MY 3.5 +IMMO/SMK : C XMA 11MY 3.5 -IMMO : C060[B6A*~B8GZ/D1BS] 3060 XMA 11MY 3.5 -IMMO : C060[B8B*~B8F*/D1AS] 3061 XMA 12MY 3.5 -IMMO : C XMA 13MY 3.5 -IMMO : C Within the ECM Upgrade screen, select Manual Mode in the left column, select Engine and then select Upgrade Event 229. Select the appropriate control unit part number by referring to the ROM ID Information Table on Page 3, and click OK. 2. Enter the appropriate password from the table on above, and click OK. 3. Upgrade will begin and the progress of the upgrade will appear on the bar graph. 4. Following the guidelines displayed on the screen during upgrade procedure, cycle the ignition OFF ON for ten (10) seconds. 5. Check if any incidental Diagnostic Trouble Codes DTC(s) have been created by the upgrade process; clear any DTC(s) that may be present. 6. Start the engine to confirm proper operation of the vehicle. https://www.motologic.com/car/2013_sorento_xm/article/a088d1-a9a3cf59445f0c6d65580ff562c5b6a0960e5dfc0?returnpath=%2fcar%2f2013_sorent 8/9

9 Page 9 of 9 AFFEC TED VEHIC LE PRO DUC TIO N RANG E: Model MY Production Date Range Sorento (XMa) From July 12, 2010 through January 31, 2013 WARRANTY C LAIM INFO RMATIO N: Claim N C Repair Labor Op Related Causal P/N Qty Time Qty Type Code Code Description Code Parts (SC106) 0.3 R C062 0 N06 C40 ECM R1 N/A 0 M/H Upgrade To assure complete customer satisfaction, always remember to refer to WebDCS Warranty Coverage (validation) Inquiry Screen (Service > Warranty Coverage >Warranty Coverage Inquiry) for a list of any additional campaigns that may need to be performed on the vehicle before returning it to the customer. https://www.motologic.com/car/2013_sorento_xm/article/a088d1-a9a3cf59445f0c6d65580ff562c5b6a0960e5dfc0?returnpath=%2fcar%2f2013_sorent 9/9