Specifications. Body Materials: Carbon steel, stainless steel, chrome-moly steel, other castable alloys

Transcription

1 CONTROL VLVES KOSO HMMEL DHL B U L L E T I N V 5 0 / FETURES Globe bodies for in-line service; angle bodies for difficult service. Each body style accepts all standard trim sets. Balanced plugs for use with smaller more economical actuators. plugs for simplicity of design, fewer parts, and ease of maintenance. Standard linear or equal percentage characterized ported cages; optional linear or equal percentage cages for difficult applications. Series V50/V50 Globe nd ngle Valves /"- 8" (DN5-00) NSI 900- The V50 (NSI 900 and 500) and V50 (NSI ) Series control valves are heavy cage guided type globe and angle valves with quick change trim. Designed for high temperature and high pressure applications, these valves feature a close tolerance integral cage and seat ring for accurate, vibration free service. The pressure drop in this design occurs across the cage openings (ports) rather than the seating surface, thus minimizing seat wear and seat leakage. pplications include throttling and on/off control of non-gritty liquids, gases, and steam at moderate to high temperature and pressures. Maximum parts interchangeability and simplicity of design result in minimum parts inventories and lower maintenance costs. Specifications ll cages for a given valve size have constant bore diameters, therefore all plugs are interchangeable regardless of design, requiring fewer part replacements. ( /" - 8" sizes) Cv reductions are achieved by reducing the area of the cage openings, not by changing its diameter or valve travel, thus eliminating the need for changing actuators. Body Style: Cage guided globe or angle Body Size: /" through 8" (5-00 mm) Body Rating: NSI 900, 500 (/" through 8"); NSI (" through ") Body Materials: Carbon steel, stainless steel, chrome-moly steel, other castable alloys End Connections: Socket weld, butt weld, raised face flange, ring type joint and others on application Bonnets: Plain or extension Trim Style: Balanced or unbalanced plug, standard ported or cage with integral seat ring. Trim Characteristic: or equal percentage Flow Coefficient: Cv from 0.40 through 680 (refer to Tables, 4 and 5). Leakage : NSI II through V ctuators: Standard bonnet mount will accept either spring-diaphragm or piston actuators. For actuator selection refer to KOSO Hammel Dahl actuator selection guide.

2 Trim Designs The V50 Series and the V50 Series are two separate product lines each designed to be a fully integrated, interchangeable system of parts. While all parts are common within each series, parts cannot be interchanged between series. Standard trim sets for the /" - " NSI 900 and 500 and " NSI valve bodies include a seat ring, a cage that acts as the seat ring retainer and the guide for a contoured plug (Fig. ). Trim sets for all other valve bodies are cages with integral seats and piston style plugs (Figures,, 4, 5, 6). 4 V 5 0 / Figure 4. Balanced Plug The standard balanced plug is piston style, which has a primary metal seat and secondary bidirectional piston rings set in ring grooves. The pressure above the plug is equalized with the pressure below the seat ring by large vent holes which pass completely through the plug. In the closed position, the plug rests on the seating surface machined in the cage and the piston rings seal the anulus between the upper plug and cage. Figure. Seated Cage The standard cage construction is a cast cage with integral seat ring. The cage serves as a massive plug guide and the close tolerance fit eliminates plug vibrations at high differential pressures. The four cage openings are contoured to establish the flow characteristic. The cage shown has openings which will provide equal percentage characteristic. linear characteristic is also available. Figure 5. Optional Balanced Plug This unique design includes a special unidirectional, spring-loaded, pressure-energized TFE cup seal. Upstream pressure enters the seal cavity compressing the seal outward, sealing the annulus between the plug and cage walls. 5 Figure. Flash-Flo This unique cage has a series of diametrically opposed drilled holes that break the flow stream into many smaller streams. For liquid applications, the trim is used as flow into the cage. Thus the high velocity streams impinge upon each other which dissipates the energy and keeps the cavitating liquid away from metal valve parts. For gas/steam applications, the trim is used as flow out of the cage. 6 Figure 6. Plug The unbalanced plug (no vent holes) is used in only flow from under the plug applications. The plug is grooved along its sides to equalize pressure in the valve body above the seat with the pressure above the plug. Thus the high velocity streams radiate out of the cage causing a redistribution of the acoustical energy with resultant noise attenuation. The cage has an integral seat ring. The V50 Series and the V50 Series together fulfill the design concept of a streamline product offering which provides maximum versatility and flexibility, yet requires a minimum of inventory and maintenance time. Figure. Contoured Trim (/"-" NSI 900, 500 and " NSI ) Table. Flow Direction Media Plug Cage Flow Direction For the /" - " globe valves the standard design is a cage with separable seat ring and cage guided contoured plug. In this design the flow area between the seat ring and the contoured plug is where throttling actually takes place. Balanced Clean Liquids Balanced Gas or Steam Flow Over Flow Under Consult Factory Flow Over Flow Under NOTE: Flow direction must be specified at time of order entry.

3 Shutoff Performance Table. Valve Leakage es Plug Style Balanced Seat Ring Plug Seal None None PTFE piston ring/o ring Carbon Graphite piston ring PTFE cup seal/spring bove leakage classes as defined in NSI B6.04. Requires seat lapping. Viton is a registered trademark of E.I. DuPont Co. NSI IV V IV II III IV V The unbalanced plug used in conjunction with any metal seat ring will provide IV shutoff or may be lapped to provide V shutoff. The standard plug seal for temperatures below 400 F (04 C) is a PTFE piston seal energized by a Viton O ring (refer to Figure 0 for pressure and temperature limitations). Supplied with any metal seated cage, this seal will provide IV shutoff. plug seal for temperatures and pressures beyond the capability of the PTFE piston ring is carbon graphite. This seal supplied with any metal seated cage will provide II shutoff. The standard plug seal for temperatures and pressures beyond the capability of the standard PTFE piston ring is a metal piston ring, which provides III shutoff. For those applications where V shutoff is required in a balanced valve, a special spring-loaded pressureenergized PTFE cup seal is available to be used in conjunction with a lapped seating surface. (Refer to Figure 0 for pressure and temperature limitations.) Flow Data Table. Flow Coefficient (C v ) at Maximum Travel -/" - 8", NSI Plug Style Cage Style Flow Characteristic Trim Size Trim Valve Size inches Code -/ Red. B Standard Red. C Red. B Balanced Red. C Red. B Red. C Red. B Red. C Red. B Standard Red. C Red. B Red. C

4 V 5 0 / Table 4. Flow Coefficient (C v ) at Maximum Travel /" - ", NSI Plug Style Flow Trim Trim Characteristic Size Code / Valve Size inches / Red. B Red. C Red. D 4 Red. E Red. F Red. G Red. H Red. B Red. C Red. D 4 Red. E Red. F Red. G.48 7 Red. H.48 Table 5. Flow Coefficient (C v ) at Maximum Travel " - ", NSI Plug Style Cage Style Flow Characteristic Trim Size Trim Code / Valve Size inches Red. B Red. C Red. D or Balanced(a) Flash Flo (a) 4 Red. E 5 Red. F 6 Red. G 7 Red. H Red. J 9 Red. K Red. B Red. C a) Trim sets with Cv of 9 or lower are available unbalanced plug and ported style cage only. 4

5 Material Selection These charts should be used to select the pressure class and trim material combination. The set of curves sloping downward to the right are the pressure rating curves for each NSI pressure class listed in NSI B6.4. In each case the curve designates the maximum pressure and temperature for the class listed directly below the curve. The bold boundaries mark the recommended pressure and temperature limits for trim material combinations listed in Table 6. These recommendations are generalized and may be subject to adjustment based upon hydraulic considerations determined during the valve sizing process. Figure 9. Trim Chart For Chrome-Moly Body (STM 7, C5) Figure 7. Trim Chart For Carbon Steel Body (STM 6, WCB) Figure 0. TFE Plug Seal Rating Chart Figure 8. Trim Chart For Stainless Steel Body (STM 5, CF8M) Figure. Hard Facing Two styles of hard-facing are provided for difficult service applications. HFS is 6 stainless steel base material with hard-facing on the seating surfaces of the plug and cage. HFS & G is 6 stainless steel base material with hard-facing on the seating surfaces of the plug and cage and the plug guiding surfaces. Plug /HFS Plug /HFS+G Cage /HFS Table 6. Trim Materials Trim Code E L O P Plug HFS+G HFS 46 SS HFS+G Cage CP-HFS CP-HFS 7-4PH/CP lloy 6* Stem * vailable in configuration only. NOTES TO TBLE ND TRIM CHRTS a) bove +600 F (6 F) extension bonnet is required. b) For service temperature above +000 F (+58 C) contact your local representative. c) Unless otherwise specified, the hard-facing is lloy 6. d) CP= Chrome plated. e) KOSO Hammel Dahl reserves the right to substitute materials when appropriate based upon service or availability. Bonnet Types Plain Bonnet plain bonnet is used when the flow medium remains between -50 F and +600 F (-45 C to +6 C). Extension Bonnet n extension bonnet is required for low temperature applications (-50 F or -9 C) and high temperature applications (+600 F to +000 F or +6 C to +58C ). 5

6 Dimensional Data V 5 0 / V50, V5, V50, V5 Body Size Inches (mm) / () /4 (0) Travel Socket Weld Raised Face Flanged Ring-Type Joint Flanged Butt Weld (79).00 (79) (67).6 (67) C Plain Bonnet (49) (49) D Extension Bonnet (79).50 (8) (8) (8).6 (67).5 (8) (49) 8.8 () (8) / (40). (9).00 (0) 5.00 (8). (). () 5.00 (8). (). () 5. (84) 5.00 (8).8 (86).56 (90) 6.60 (68) 8.8 ().44 (9).06 () (50). (9) 4.75 (75) (400) 4.75 (75) 4.75 (75) 6.5 (4) 4.88 (78) 4.88 (78) 6.8 (46) (400).75 (95) 4.06 (0) 7.4 (86) 8.75 ().56 (94) 4.56 (70) (80).50 (8) 7.8 (44) 8. (460) 6.00 (660) 7.50 (445) 8.5 (464) 6.5 (667) 8. (460) 6.00 (660) 4.88 (4) 7.8 (87) 0. (57) 6.50 (49).6 () 4.00 (60) 4 (00).50 (8) 0. (5) 0.88 (50) 0.5 (54).00 (5) 0.88 (50) 5.56 (4). (8).88 (5) 6 (50).5 (57) 8. (74) 0.5 (768) 8.5 (78) 0.50 (775) 0.5 (768) 7.00 (78) 8 (47) 6. (664) 8 (00).50 (89) 6.00 (94) 8.5 (97) 6. (97) 8.6 (98) 8.5 (97) (454). (56) Body Size Inches (mm) / () /4 (0) / (40) (50) (80) 4 (00) 6 (50) V5, V5, V5, V5 Travel. (9). (9).5 (8).5 (8).5 (57) Socket Weld Raised Face Flanged Ring-Type Joint Flanged Butt Weld (40) 5.50 (40) 5.50 (40) 6.50 (65) 7.8 (87) 6.5 (59) 7.50 (9) 7.88 (00) (46) (46) 6.56 (67) 7.8 (87) 8.69 () 0.06 (56) 4.06 (57) (46) (46) 6.56 (67) 7.8 (87) 9.06 (0) 0.44 (65) 5. (84) 6.5 (59) 7.50 (9) 8. (06) (46) 6.56 (67) 7.44 (89) 8.75 () 0. (57) 4. (59) (46) 6.56 (67) 7.44 (89) 9. () 0.50 (67) 5.5 (87) 6.5 (59) 7.56 (9) 8.9 (08) 9.06 (0) 0.44 (65) 5. (84) 7.50 (9) 7.88 (00).00 (0) Plain Bonnet (49) (49) (49) 6.6 (68) 7.8 (87) 0. (57). (8) 4.00 (56) 8.8 () 8.8 () 8.75 () D Extension Bonnet (9).56 (94).6 ().88 (5) 8.69 (475).50 (8).06 () 4.56 (70) Globe style face-to-face dimensions are in accordance with NSI B6.0 and IS S75.6 for raised face flanged valves. 6

7 How To Order To completely specify a control valve, make a selection from each category in the Valve Model Coding System below. The assembled codes create a complete valve model number. The Valve Model Coding System displays the standard product offering for this product line. n extensive number of options and variations exist, which are not listed. For options not shown or to enter an order, contact your local sales representative. V50 N N K 5 F B P 9 B Model V50 V5 V5 V5 NSI 900, I500 Balanced, Globe Body Balanced, ngle Body, Globe Body, ngle Body V50 V5 V5 V5 Body Size D /" ( mm) E /4" (0 mm) F " (5 mm) H /" (40 mm) J " (50 mm) L " (80 mm) N 4" (00 mm) Q 6" (50 mm) S 8" (00 mm) Rating M NSI 900 N NSI 500 R NSI * *" through " valves only. NSI Balanced, Globe Body ( /" - " size) Balanced, ngle Body ( /" - " size), Globe Body (" - " size), ngle Body (" - " size) 7 Trim Characteristics C, E, F Flash-Flo H Flash-Flo, 8 Trim Size B Reduction C Reduction NOTE: Refer to Cv tables on pages and 4 for additional options. 9 Trim Materials Trim Code Plug Cage Stem E L O P /HFS+G /HFS 46 SS /HFS+G /CP-HFS /CP-HFS 7-4PH/CP lloy 6* * vailable in Flash-Flo configuration only. 0 Packing -00 F to +450 F (-9 C to + F) G U PTFE V-Ring with Packing Spacer PTFE Impregnated PTFE Braided Ring +450 F to +000 F/+ C to +58 C 9 Laminated Graphite Ring 4 Body Material C Carbon Steel (STM 6, WCB) E Stainless Steel (STM 5, CF8M) K Chrome-Moly Steel (STM 7, C5) 5 End Connections Raised Face Flange 5 Ring Type Joint Flange 6 Socket Weld 9 Butt Weld Sch. 80* Butt Weld Sch. 60 * NSI 900 and 500 only. 6 Bonnet Type Plain Extension Variations None B Plug Seal Ring - Body Drain (/" NPT) J Plug Seal Ring - TFE/O-Ring K Plug Seal Ring - Carbon Graphite N Plug Seal Ring - TFE Cup Seal, Spring Loaded 8 Stainless Steel Body Studs and Nuts 9 Stainless Steel Lubricator and Isolating Valve NOTE: If more than one variation is required, use code Z and describe each variation. NOTE: plug seal must be specified in the variation code for all balanced style valves. NOTE: Flow direction must be specified at time of order entry. 7

8 D/R Series Spring Diaphragm Pneumatic ctuators KOSO Hammel Dahl linear spring diaphragm pneumatic actuators are rugged units designed for reliable operation of linear control valves. The available combinations of case sizes, strokes, and springs precisely satisfy a wide range of application requirements. FETURES Rolling diaphragm provides excellent sensitivity and provides maximum constant effective area which translates into improved linearity. Modular construction provides maximum part interchangeability between direct and reverse-acting models and between selected case sizes field reversibility is easily accomplished. High spring rates improve control valve stability. Minimal guiding assures low hysteresis in reverse-acting models zero hysteresis in direct-acting models. Stainless steel stems are standard for maximum performance in corrosive environments. Specifications Diaphragm Cases: Pressed steel Stem: 0 SS Diaphragm: Dacron reinforced nitrile Spring Barrel: Cast Iron Max. Case Pressure: 65 psi (4.5 bar) Temperature Limits: -40 F to +80 F (-40 C to +8 C) Standard Spring Spans: psi and 4 psi (.8 bar and.7 bar) (other spans and spring preloads available on application) REX Electraulic ctuators The REX actuator is a programmable, self-contained, electrohydraulic actuator designed specifically for modulating control. REX actuators combine the speed, power and repeatability of non-compressible hydraulics with the flexibility of a dedicated microprocessor. vailable in a wide range of sizes and product options, there is a REX actuator to meet even the most demanding control applications. Positioners The NP700 and NE700 are proportional positioners for globe valve throttling applications. The NP is a fully pneumatic unit while the NE is an electro-pneumatic unit that provides pneumatic out-put proportional to a standard millampere DC Input. The ND800 digital positioner provides extensive monitoring for diagnostics as well as improves response speed. Used with D/R Series diaphragm actuators, these units improve repeatability and accuracy while providing increased force to reduce actuator sizes. KOSO and other instrument manufacturers positioners are also available upon request. Other ccessories dditional accessories available for mounting with linear control valves include, but are not limited to transducers, limit switches, lock-up valves, solenoid valves and amplifying relays. Please consult the factory for complete details. KOSO MERIC, INC. 4 Manley Street W. Bridgewater, M 079 0/04 Telephone: Fax: CONTROL VLVES KOSO HMMEL DHL