CARBURETOR SERVICE INFORMATION TROUBLESHOOTING THROTTLE VALVE DISASSEMBLY THROTTLE VALVE INSTALLATION...
|
|
- Duane McGee
- 1 years ago
- Views:
Transcription
1 11 CARBURETOR SERVICE INFORMATION TROUBLESHOOTING THROTTLE VALVE DISASSEMBLY THROTTLE VALVE INSTALLATION CARBURETOR REMOVAL AUTO BYSTARTER FLOAT CHAMBER FLOAT LEVEL INSPECTION CARBURETOR INSTALLATION AIR SCREW ADJUSTMENT REED VALVE FUEL TANK
2 11-1
3 SERVICE INFORMATION GENERAL INSTRUCTIONS When working with gasoline, keep away from sparks and flames.. Note the locations of O-rings when disassembling and replace them with new ones during assembly. All cables, fuel lines and wires must be routed and secured at correct locations. Bleed air from the oil lines whenever they are disconnected. SPECIFICATIONS Standard Venturi dia. 16mm Identification number PB Float level 8.6mm Main jet #72 Slow jet #35 Air screw opening 1¼ ± ½ Idle speed 2000±100rpm Throttle grip free play 2~6mm SPECIAL TOOL Float level gauge TROUBLESHOOTING Engine does not start Lean mixture No fuel in tank Clogged fuel jets Faulty float valve Too much fuel getting to cylinder Clogged fuel cap vent Float level too low Clogged fuel filter Clogged fuel filter Clogged air cleaner Clogged air cleaner Bent, kinked or restricted fuel line Engine idles roughly, stalls or runs poorly Rich mixture Incorrect idle speed Clogged air cleaner Faulty float valve Ignition malfunction Intake air leaks Float level too high Compression too low Fuel contaminated Clogged air jets Incorrectly adjusted air screw Faulty reed valve Incorrect float level Clogged fuel jets 11-2
4 THROTTLE VALVE DIS-ASSEMBLY Remove the rear carrier. Remove the met-in box. Remove the rubber cover. Loosen carburetor cap and the throttle valve. Rubber Cover Disconnect the throttle cable from the throttle valve. Throttle Valve Remove the throttle valve spring, carburetor cap and rubber seal. Rubber Seal Carburetor Cap 11-3 Spring
5 Remove the jet needle by removing the needle clip. Check the jet needle and throttle valve for wear or damage. Needle Clip Jet Needle Throttle Valve THROTTLE VALVE INSTALLATION Install the jet needle on the throttle valve and secure with the needle clip. Install the rubber seal on the throttle cable and then install the carburetor cap and throttle valve spring. Rubber Seal Carburetor Cap Throttle Valve Spring Connect the throttle cable to the throttle valve. Throttle Valve Throttle Cable 11-4
6 Install the throttle valve by aligning the groove in the throttle valve with the throttle stop screw. Groove Throttle Stop Screw Tighten the carburetor cap. After installation, perform the following adjustments and inspections. Throttle cable free play Idle speed adjustment Install the met-in box. Carburetor Cap Throttle Cable Fuel Tube CARBURETOR REMOVAL Remove the met-in box. Remove the air cleaner by removing the air cleaner band screw and attaching bolts. Disconnect the fuel tube. Loosen the drain bolt to drain fuel from the carburetor. Disconnect the auto by-starter wire connector. Remove the two carburetor lock nuts. Drain 11-5
7 Remove the carburetor. Nut AUTO BYSTARTER AUTO BYSTARTER INSPECTION Measure the resistance between the auto bystarter wire terminals. Resistance: 5Ω (10 minutes minimum after stopping the engine) If the resistance exceeds 5Ω, replace the auto bystarter with a new one. After the engine stops for 30 minutes, connect a hose to the fuel enriching circuit and blow the hose with mouth. If air cannot be blown into the hose (clogged), the auto by-starter is faulty. Replace it with a new one. 11-6
8 Connect the auto bystarter yellow wire to the battery positive (+) terminal and green/ black wire to the battery negative (-) terminal and wait 5 minutes. Connect a hose to the fuel enriching circuit and blow the hose with mouth. If air can be blown into the hose, the auto bystarter is faulty and replace it with a new one. Set Plate Screws AUTO BYSTARTER REMOVAL Remove the auto by-starter cover. Remove the two auto-bystarter set plate screws to remove the auto by-starter. Auto By-starter Check the auto by-starter valve and needle for wear or damage. Check the O-ring for wear or damage. O-ring Bystarter Needle Bystarter Valve 11-7
9 AUTO BYSTARTER INSTALLATION Install the auto bystarter into the carburetor body until it bottoms.. Install the set plate and then tighten the two screws. Screws Auto Bystarter FLOAT CHAMBER Remove the two float chamber screws and the float chamber. Set Plate Screws Remove the screw and O-ring. Remove the float pin, float and float valve. Float Pin O-ring Float 11-8
10 FLOAT/FLOAT VALVE INSPECTION Inspect the float for damage or fuel inside the float. Check the float valve seat for wear or damage. Float Valve Float Seat JETS/SCREWS REMOVAL Before removing the throttle stop screw or air screw, record the number of rotations until it seats lightly. Then, remove them. Do not force the air screw against its seat to prevent damage. Main Jet Remove the main jet and needle jet holder. Throttle Stop Screw Air Screw CARBURETOR PASSAGES CLEANING Blow compressed air through all passages of the carburetor body with an air gun. 11-9
11 FLOAT CHAMBER ASSEMBLY Install the main jet and needle jet holder. Install the air screw and throttle stop screw according to the rotations recorded. If the air screw must be replaced, be sure to perform the air screw adjustment again. Needle Jet holder Main Jet Air Screw Throttle Stop Screw Slow Jet Install the float valve, float and float pin. Tighten the float screw securely. Float Pin FLOAT LEVEL INSPECTION Slightly tilt the carburetor and measure the float level with the float valve just connecting the float arm. Float Level: 8.6mm Replace the float if the level is out of the specified level range. Install the O-ring. Check the operation of the float and install the float chamber. Tighten the screws
12 O-rings CARBURETOR INSTALLATION Check the carburetor insulator and O-ring for wear or damage. Install the carburetor and insulator onto the intake manifold and tighten the two lock nuts. Connect the fuel tube and auto by-starter wire connector. Install the carburetor cap. Install the air cleaner onto the carburetor and tighten the band screw. Install the met-in box. AIR SCREW ADJUSTMENT Remove the met-in box. When installation, do not allow foreign particles to enter the carburetor. Route the auto by-starter wire correctly and properly. Warm up the engine before air screw adjustment. Turn the air screw clockwise until it seats lightly and back it to the specification given. Air Screw Opening: : 1¼ ± ½ turns Insulator Fuel Tube Carburetor Cap Start the engine and turn the air screw in or out slowly to obtain the highest engine speed. Do not force the air screw against its seat to prevent damage. Turn the throttle stop screw to obtain the specified idle speed. Idle Speed: 2000±100rpm Air Screw Slightly increase the engine speed and make sure that the engine does not miss or run erratic. If the adjustment of the air screw within the range of ±½ turn makes no difference to the engine performance, check other related items. Throttle Stop Screw 11-11
13 REED VALVE REMOVAL Remove the rear carrier. Remove the frame body cover. Remove the four intake manifold bolts and gasket. Remove the reed valve and gasket. Bolts Intake Manifold INSPECTION Check the reed valve for damaged or weak reeds. Check the reed valve seat for cracks, damage or clearance between the seat and reed. Replace the valve if necessary. Do not disassemble or bend the reed stopper. To do so can cause loss of engine power and engine damage. If any of the stopper, reed or valve seat is faulty, replace them as a unit. Reeds Reed Stopper Reed Valve Seat INSTALLATION Install the reed valve in the reverse order of removal. Install a new gasket with the gasket indentation aligned with the reed valve. After installation, check for intake air leaks
14 FUEL TANK Bolts Fuel Unit Fuel Tank REMOVAL Remove the met-in box. Remove the frame body cover. Remove the rear carrier. Disconnect the fuel tube and vacuum tube at the auto fuel tank. Disconnect the fuel unit wire connector. Remove the fuel tank holder mounting bolts and fuel tank. Inspect the fuel unit. Replace the fuel unit if necessary. Fuel Tank Holder Fuel Tube ASSEMBLY 11-13
11. CARBURETOR 11-0 CARBURETOR ZX / SCOUT 50
11 CARBURETOR SERVICE INFORMATION... 11-2 TROUBLESHOOTING... 11-2 THROTTLE VALVE DISASSEMBLY... 11-3 THROTTLE VALVE INSTALLATION... 11-4 CARBURETOR REMOVAL... 11-5 AUTO BYSTARTER... 11-6 FLOAT CHAMBER...
WEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
PIERBURG. Carburetor: 2E3
PIERBURG Carburetor: 2E3 1 fast idle adjusting screw 2 throttle lever 3 fuel mixture adjusting screw 4 main body 5 idle cut off valve 6 stop screw 7 accelerator pump cover 8 diaphragm 9 spring 10 valve
TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: FAX:
TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: +353 66 7121911 FAX: +353 66 7124503 e-mail: sales@tillotson.ie SERIES SERVICE MANUAL INTRODUCTION The gasoline engine industry
Typical Install Instructions
Typical Install Instructions Read & understand all steps of these instructions before beginning this installation. WEBER Conversion Kit, VW T-1/2, up to 1835cc 32 / 36 DFEV Weber Carburetor These instructions
FUEL AND LUBRICATION SYSTEM
AND LUBRICATION SYSTEM 4-1 A-PDF Split DEMO : Purchase from www.a-pdf.com to remove the watermark AND LUBRICATION SYSTEM CONTENTS SYSTEM... 4-2 PUMP... 4-2 TANK/ COCK... 4-3 REMOVAL... 4-3 INSPECTION...
JOB AID INTRODUCTION TOOLS REQUIRED: GC160 GC190 GS190 GCV160 GCV190 GSV160 GSV190 CARBURETOR CLEANING
JOB AID GC160 GC190 GS190 GCV160 GCV190 GSV160 GSV190 CARBURETOR CLEANING INTRODUCTION Service engineering has discovered that many GCV carburetors returned for warranty were improperly cleaned. Eighty
CARBURETOR - HITACHI 2-BBL
CARBURETOR - HITACHI 2-BBL 1986 Isuzu Trooper II 1986 Hitachi Carburetors HITACHI DCH340, DCR384, DFP340, DFP384 & DHP340 2-BARREL P UP & Trooper II DESCRIPTION Carburetor is a 2-barrel downdraft type
SPECIFICATIONS ITEM TORQUE NOTES. Air cleaner backplate screw 7-9 ft-lbs Nm LOCTITE THREADLOCKER 242 (blue), page 4-19
4 SPECIFICATIONS CARBURETOR JET SIZES CARBURETOR ADJUSTMENTS Main jet 195 Slow jet 42 FUEL TANK CAPACITY GALLONS LITERS Total (including reserve) 4.0 15.14 Reserve 0.6 2.27 Engine fast idle speed (using
TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: FAX:
TILLOTSON LTD., CLASH INDUSTRIAL ESTATE, TRALEE, CO. KERRY, IRELAND PHONE: +353 66 7121911 FAX: +353 66 7124503 e-mail: sales@tillotson.ie HR SERIES SERVICE MANUAL INTRODUCTION Tillotson has developed
Checking Solenoid Plunger Travel
1985 Chevy Truck EL Camino V8-305 5.0L Page 1 Carburetor: Adjustments Carburetor Calibration E2M & E4M Series Mixture Control Solenoid Plunger Travel Checking Solenoid Plunger Travel OTE: Mixture control
CARBURETION. Flo-Jet Carburetors. One Piece. One-Piece Flo-Jet. Main Jet Adjustment N eedle
One Piece One-Piece Flo-Jet The small One-Piece Flo-Jet carburetor is illustrated in Fig. 122 and was used on early Model 170700. These are float feed carburetors with adjustable orifice main jet needle
Body type location. Model number location. Small Engine Parts
Body type location Model number location Small Engine Parts FUEL PUMP SYSTEM SYSTEMS AND OPERATION The fuel pump on a diaphragm carburetor uses the vacuum and pressure pulse from the engines crankcase
AN EXPLANATION OF CIRCUITS CARTER YH HORIZONTAL CLIMATIC CONTROL CARBURETER
AN EXPLANATION OF CIRCUITS CARTER YH HORIZONTAL CLIMATIC CONTROL CARBURETER The Carter Model YH carbureter may be compared with a Carter YF downdraft carbureter with the circuits rearranged to operate
Performer Series Carburetor Rebuild Kit Catalog #1477 Models
Please read these instructions carefully before attempting to rebuild your carburetor. Make sure to refer to your carburetor Owner s Manual for further information if need be. If you have any questions
Днепр) Russian Motorcycle Carburetors Part 11: VM 28mm Mikuni
Ural (Урал( Урал) - Dnepr (Днепр( Днепр) Russian Motorcycle Carburetors Part 11: VM 28mm Mikuni (See Also Part 11A: VM Mikuni Carb Manual) Ernie Franke eafranke@tampabay.rr.com 04/2011 Mikuni VM-28 Round-Slide
Oregon Fuel Injection
Cummins PT Fuel Pump Diagnostic No Start, with no smoke 1. This could be caused by the fuel pump not turning or a seized gear pump. Remove the fuel supply hose and the fuel inlet fitting from the gear
HSR Carburetor Easy Kits Installation Instructions For Evo Big Twin Kit: # 42-7 Twin Cam Kit: # 42-18
HSR Carburetor Easy Kits Installation Instructions For Evo Big Twin Kit: # 42-7 Twin Cam Kit: # 42-18 Revised 5/01/01 EK-1 Easy Kit Installation Instructions The HSR series carburetors are precise yet
HSR Carburetor. Total Kits. Installation Instructions. # Evo Big Twin # present Twin Cam
HSR Carburetor Total Kits Installation Instructions HSR42 Kits: HSR45 Kits: #42-8 84-99 Evo Big Twin #42-19 99 - present Twin Cam #45-2 84-99 Evo Big Twin #45-3 84-99 Evo Big Twin #45-4 99 - present Twin
ENGINE AND EMISSION CONTROL
17-1 ENGINE AND EMISSION CONTROL CONTENTS ENGINE CONTROL SYSTEM........ 3 SERVICE SPECIFICATION............... 3 ON-VEHICLE SERVICE.................. 3 Accelerator Cable Check and Adjustment... 3 ACCELERATOR
MIKUNI VM26 Carburetor Kit Instruction Manual
MIKUNI VM26 Carburetor Kit Instruction Manual (For exclusive use in the Super Head 4VALVE+R-equipped motorcycle) Item No. (Carburetor set) AKEGAWA-made products. Please strictly follow the following instructions
1. SPECIFICATIONS 1-0 TABLE OF CONTENTS
1. SPECIFICATIONS 1 TABLE OF CONTENTS 1 SPECIFICATIONS... 1 GENERAL INFORMATION... 2 INSPECTION/ADJUSTMENT... 3 LUBRICATION SYSTEM... 4 ENGINE REMOVAL/INSTALLATION... 5 CYLINDER HEAD/CYLINDER/PISTON...
HUDSON MOTOR CAR COMPANY
HUDSON MOTOR CAR COMPANY 1935-1942 Carburetor Tune-up Manual ( for Hudson and Terraplane Models) Index Carter W-1 Downdraft 1935-1942 1 Carter W-1 Vacumeter Type 1938 Hudson 4 Carter WA-1 Vacumeter Type
Section 5 Fuel System and Governor
Section Description The Command horizontal twins use three different types of fuel systems; carbureted, electronic fuel injection (EFI), or gaseous. Gaseous fuel systems can be either liquefied petroleum
DESCRIPTION FUEL AND VACUUM PUMP REMOVE AND REPLACE FUEL PUMP-OVERHAUL 6B PONTIAC SHOP MANUAL. S. Install battery and connect cables.
6B-74 1955 PONTIAC SHOP MANUAL DESCRIPTION FUEL AND VACUUM PUMP All models are equipped with a combination fueland double acting vacuum pump operated by an eccentric bolted to the front end of the engine
General Service Information
KYMCO MXU 500i/700i Repair Manual Fuel System MXU 700i 3.Fuel System MXU 700i This chapter covers the location and servicing of the fuel system components for the fuel injected KYMCO MXU 700i models. 1.Airbox...
7. CYLINDER HEAD/VALVES
7 7 7-0 SERVICE INFORMATION...7-1 CYLINDER HEAD DISASSEMBLY...7-7 TROUBLESHOOTING...7-2 CYLINDER HEAD ASSEMBLY...7-8 CAMSHAFT REMOVAL...7-3 CYLINDER HEAD INSTALLATION...7-8 CYLINDER HEAD REMOVAL...7-5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4A FE)
ENGINE EG121 EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4AFE) EGR SYSTEM INSPECTION 1. INSPECT AND CLEAN FILTER IN EGR VACUUM MODULATOR (a) Remove the cap and filter. (b) Check the filter for contamination
Instruction Model 18537
Instruction 738-556 Model 18537 LIMITED WARRANTY H. D. Hudson Manufacturing Company warrants to the original purchaser only that this product will continue to function as intended if used in accordance
TECH INFORMATION EMPI D Performance 2-Barrel Carburetor
TECH INFORMATION EMPI D Performance 2-Barrel Carburetor The New EMPI D 2-Barrel Performance Carburetor.Built specifically for the VW Aftermarket. With all the features that you have asked for More Progression
5-2 FUEL SYSTEM AND THROTTLE BODY FUEL SYSTEM FUEL DELIVERY SYSTEM The fuel delivery system consists of the fuel tank, fuel pump, fuel filters, fuel f
FUEL SYSTEM AND THROTTLE BODY 5-1 FUEL SYSTEM AND THROTTLE BODY I CONTENTS FUEL SYSTEM 5-2 FUEL DELIVERY SYSTEM 5-2 FUEL PUMP 5-3 FUEL PRESSURE REGULATOR 5-4 FUEL INJECTOR 5-4 FUEL PUMP CONTROL SYSTEM
PLEASE NOTE: This is a PRELIMINARY copy of the Carburetor Reference Manual.
PLEASE NOTE: This is a PRELIMINARY copy of the Carburetor Reference Manual. Carburetor Service Kits The carburetors for most current production engines are serviced with convenient kits, which include
1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza
1.8L & 2.2L 4-CYL Article Text 1998 Subaru Impreza ARTICLE BEGINNING 1995-98 ENGINES Subaru - 1.8L & 2.2L 4-Cylinder 1995-97: Impreza (1.8L) 1995-98: Impreza (2.2L), Legacy (2.2L) * PLEASE READ THIS FIRST
ENGINE AND EMISSION CONTROL
17-1 GROUP 17 ENGINE AND EMISSION CONTROL CONTENTS ENGINE CONTROL.......... 17-3 GENERAL DESCRIPTION...... 17-3 ENGINE CONTROL SYSTEM DIAGNOSIS.................. 17-3 INTRODUCTION TO ENGINE CONTROL SYSTEM
EG2 173 EXHAUST GAS RECIRCULATION (EGR) SYSTEM
5SFE ENGINE EG2173 EXHAUST GAS RECIRCULATION (EGR) SYSTEM EG2174 5SFE ENGINE EGR SYSTEM INSPECTION 1. INSPECT AND CLEAN FILTER IN EGR VACUUM MODULATOR (a) Remove the cap and filter. (b) Check the filter
BRAWLER SERIES CARBURETORS
BRAWLER SERIES CARBURETORS Installation Instructions Please Stop and Read these Instructions before proceeding. If you do not fully understand the installation and tuning instructions you should seek professional
GENERAL DESCRIPTION ROCHESTER 4GC 4-JET CARBURETOR 6B PONTIAC SHOP MANUAL
6B-56 1955 PONTIAC SHOP MANUAL GENERAL DESCRIPTION ROCHESTER 4GC 4-JET CARBURETOR The Rochester 4GC Carburetor for the 1955 Pontiac V -8 is essentially two 2 -J et carburetors in a single casting. The
Rev /30/2000
ETON America Sierra DXL-90 Service Manual Spartanburg, SC 29303 Rev 2.0.0 06/30/2000 TABLE OF CONTENTS Section Table of Contents Page 1. INFORMATION 5 2. MAINTENANCE 9 3. ENGINE REMOVAL AND INSTALLATION
EMISSION CONTROL SYSTEMS
EMISSION CONTROL SYSTEMS (3SFE) EMISSION CONTROL SYSTEMS EC1 EC2 EMISSION CONTROL SYSTEMS (3SFE) System Purpose System SYSTEM PURPOSE Abbreviation Purpose Positive crankcase ventilation Fuel evaporative
EXHAUST GAS RECIRCULATION (EGR) SYSTEM
3SGTE ENGINE EG1243 EXHAUST GAS RECIRCULATION (EGR) SYSTEM To reduce NOx emissions, part of the exhaust gases is recirculated through the EGR valve to the intake manifold to lower the maximum combustion
Repair Manual 11/99 PS-34. Page 1
Repair Manual /99 PS-4 Page Table of contents Index Technical Data page Special tools 4 Repair instructions, general 0 Chain brake 6 0 Centrifugal clutch 8 0 Oil pump 9-04 Ignition system - 0 Starting
Fuel System Service & Diagnostic Equipment OPERATOR S MANUAL MCS 245
Fuel System Service & Diagnostic Equipment OPERATOR S MANUAL MCS 245 Table of Contents Introduction...3 Overview...4 System Features and Functions...5 System Features and Functions... Hose and Battery
CIRRUS AIRPLANE MAINTENANCE MANUAL
POWER PLANT 1. GENERAL This chapter describes maintenance practices for the airplane systems which provide the means to induce and convert fuel-air mixture into power such as the engine, baffling, cowling,
GIOUP 11 EXHAUST SYSTEM
EXHAUST SYSTEM 11-1 GIOUP 11 EXHAUST SYSTEM CONTENTS Page Exhaust Manifold...... -4 Exhaust Pipes, Mufflers and Tail Pipes... 5 -Intake Manifold... 4 Manifold Heat Control Valve... 5 Manifold Heat Control
SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking
CARBURETOR P/N , C, S, & CT INSTALLATION, TUNING, AND ADJUSTMENT MANUAL 199R7950-7
CARBURETOR P/N 0-7448, 0-4412C, 0-4412S, & 0-4412CT INSTALLATION, TUNING, AND ADJUSTMENT MANUAL 199R7950-7 NOTE: These instructions must be read and fully understood before beginning installation. If this
EDELBROCK PERFORMER SERIES EMISSIONS LEGAL CARBURETOR 600cfm, Electric Choke, EGR, Square-Bore Carburetor. Part #1400 INSTALLATION INSTRUCTIONS
EDELBROCK PERFORMER SERIES EMISSIONS LEGAL CARBURETOR 600cfm, Electric Choke, EGR, Square-Bore Carburetor INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation.
Rebuild and Adjustment Manual for Models 2010, 2300, 4010, 4011, 4150, 4160, 4165, 4175, and 4500
Rebuild and Adjustment Manual for Models 2010, 2300, 4010, 4011, 4150, 4160, 4165, 4175, and 4500 WARNING! These instructions must be read and fully understood before beginning installation. Failure to
VERTICAL CRANKSHAFT SERVICE MANUAL COURAGE SV COURAGE PRO SV
VERTICAL CRANKSHAFT SERVICE MANUAL COURAGE SV710-740 COURAGE PRO SV810-840 Contents Section 1. Safety and General Information... Section 2. Tools & Aids... Section 3. Troubleshooting... Section 4. Air
TM-1. Tuning Manual. For HSR42/45 CARBURETORS. Revised 5/10/00
TM-1 Tuning Manual For HSR42/45 CARBURETORS Revised 5/10/00 TM-2 Tuning the HSR Your Mikuni HSR is fitted with the tuning parts we found to work with the great majority of engine performance modifications.
PRO-R AIR CLEANER FOR KAWASAKI 9462
I N S TA L L AT I O N PRO-R AIR CLEANER FOR KAWASAKI 9462 FITS: 95-04 VN1500 (SINGLE CARB MODELS) PART # INCLUDED 500205 1 Pro R Hypercharger Chrome Assembly Including: 1 Dual Velocity Ring (in plastic
COMMANDER Oz AIR/FUEL CONTROL UNIT IMPCO PART EK-CDP-1/EK-CDP-1H Kit INSTALLATION INSTRUCTIONS
COMMANDER Oz AIR/FUEL CONTROL UNIT IMPCO PART EK-CDP-1/EK-CDP-1H Kit INSTALLATION INSTRUCTIONS INTRODUCTION This document will show you how to install the IMPCO Commander Oz fuel control processor for
SECTION 3.00 WARNING WARNING ENGINE STARTUP AND SHUTDOWN PRESTART INSPECTION
SECTION 3.00 ENGINE STARTUP AND SHUTDOWN PRESTART INSPECTION Be sure that the clutch, circuit breaker, or other main power transmission device is disconnected. Generators develop voltage as soon as the
FUEL SYSTEM PRECAUTION FU 1
2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions
Cooling system components, removing and installing
19-1 Cooling system components, removing and installing Note: When the engine is warm the cooling system is under pressure. If necessary release pressure before starting repair work. Hoses are secured
Illustrated Parts List. Model Series 31F700. TYPE NUMBERS 0110 through TABLE OF CONTENTS
Illustrated Parts List Model Series 31F700 TYPE NUMBERS 0110 through 0403. TABLE OF CONTENTS FORM MS--5035--04/27/2009 REPLACES FORM MS--5035--09/29/2008 FILE IN SECT. 2 OF SERVICE MANUAL 31F700 Air Cleaner...
Vacuum Readings for Tuning and Diagnosis
Vacuum Readings for Tuning and Diagnosis -Henry P. Olsen Once you learn to properly interpret its readings, a vacuum gauge can be one of the most useful tools in your toolbox. 22 FEATURE Some people consider
Illustrated Parts List
01/08/2010 FILE IN SECT. 2 OF SERVICE MANUAL PRO DRIVE 613777-0113 -E1 Illustrated Parts List Model Series AIR COOLED 613777 TYPE NUMBERS 0113. TABLE OF CONTENTS Air Cleaner... Alternator... Blower Housing/Shrouds...
ENGINE MECHANICAL <3.0L ENGINE>
11C-1 GROUP 11C ENGINE MECHANICAL CONTENTS GENERAL DESCRIPTION......... 11C-2 ENGINE DIAGNOSIS............. 11C-3 SPECIAL TOOLS................ 11C-4 ON-VEHICLE SERVICE........... 11C-6 DRIVE
2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX
2004 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX ENGINE SECTION 1 FU(H4SO) EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES) INTAKE (INDUCTION) EC(H4SO) IN(H4SO) This service manual has been prepared to
FBC CODES AND TRANSLATIONS TRANSLATION
FBC CODES AND TRANSLATIONS CODE TRANSLATION 500 air cleaning system checked 501 air cleaner housing found cracked 502 repaired cracked air cleaner housing 503 renewed air cleaner housing 504 air intake
DTC P0340 CMP SENSOR (PHASE) DTC No. Trouble diagnosis name DTC detecting condition Possible cause
DTC P0340 CMP SENSOR (PHASE) Component Description DTC P0340 CMP SENSOR (PHASE) The camshaft position sensor (PHASE) senses the retraction with intake valve camshaft to identify a particular cylinder.
EXHAUST GAS RECIRCULATION (EGR) SYSTEM
ENGINE EG169 EXHAUST GAS RECIRCULATION (EGR) SYSTEM (California only) EG170 ENGINE To reduce NOx emissions, part of the exhaust gases are recirculated through the EGR valve to the intake manifold to lower
Mazda Reference MA014
Subject: Fuel system pressure testing for fuel injected engines Symptom: Hard starting cold, power loss climbing hills, overall poor performance, engine surges and then stops running Source: Mazda service
8 TROUBLESHOOTING
8 DRIVE AND DRIVEN PULLEYS/ SCHEMATIC DRAWING------------------------------------------------------------------------- 8-1 SERVICE INFORMATION-----------------------------------------------------------------------
ENGINE COOLING Click on the applicable bookmark to selected the required model year
ENGINE COOLING - ENGINE COOLING General Information/ Service Specifications/Lubricant/Sealants GENERAL INFORMATION 0000 The cooling system is designed to keep every part of the engine at appropriate temperature
I: INSPECT AND CLEAN, ADJUST, LUBRICATE OR REPLACE IF NECESSARY C: CLEAN A: ADJUST R: REPLACE L: LUBRICATE I: INSPECTION D: DIAGNOSE
2. Periodic Maintenance > Periodic Maintenance Chart XCITING 400i Maintenance Schedule Perform the pre-ride inspection (Owner's Manual) at each scheduled maintenance period. This interval should be judged
Illustrated Parts List AA0101 AA0101. Model Series TABLE OF CONTENTS TYPE NUMBER 0001, 0005, 0020, Blower Housing/Cowl Carburetor...
FORM MS 5131 10/27/2004 REPLACES FORM MS 5131 09/01/2003 AA0101 Illustrated Parts List TABLE OF CONTENTS Model Series AA0101 TYPE NUMBER 0001, 0005, 0020, 0025. Blower Housing/Cowl.....................
COMPETITION CARBURETORS MODEL 4500 ULTRA HP DOMINATOR SERIES P/N (1050 cfm) & (1150 cfm)
COMPETITION CARBURETORS MODEL 4500 ULTRA HP DOMINATOR SERIES P/N 0-80672 (1050 cfm) & 0-80673 (1150 cfm) Installation and Adjustment Instructions P/N 199R10322 CONGRATULATIONS on your purchase of Holley
COMMANDER Oz AIR/FUEL CONTROL UNIT IMPCO PART EK-CDP-1 INSTALLATION INSTRUCTIONS
COMMANDER Oz AIR/FUEL CONTROL UNIT IMPCO PART EK-CDP- INSTALLATION INSTRUCTIONS INTRODUCTION This document will show you how to install the IMPCO Commander Oz fuel control processor for industrial engines.
INJECTOR COMPONENTS SF-18. Air Cleaner Hose. Accelerator Cable Water Bypass Hose Air Hose. PCV Hose. Throttle Position Sensor Connector.
SF18 SFI (5VZFE) COMPONENTS SF02204 Air Cleaner Hose PCV Hose Accelerator Cable Water Bypass Hose Air Hose Throttle Position Sensor Connector CCV Hose Accelerator Pedal Position Sensor Connector Throttle
solo service Service-manual For the aircraft engines solo solo solo i
solo service Service-manual For the aircraft engines solo solo solo i solo Kleinmotoren GmbH Stuttgarter Str. 41 D 71069 Sindelfingen Tel.: (0049) 7031-3010 Fax.: (0049) 7031 301195 Edition 2 dated October
2014+ Ram 3.0 EcoDiesel EGR Delete
2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD
750 STREET DEMON Part Numbers: 1903, 1904, & 1905
750 STREET DEMON Part Numbers: 1903, 1904, & 1905 INSTRUCTION MANUAL LIT731 US Patent # D648746S www.demoncarbs.com 1 Table of Contents INTRODUCTION... 2 Recommended Parts and Accessories... 3 Removal
400 2x4/4x4 EFT SHARE OUR PASSION ṬM
SHARE OUR PASSION ṬM 400 2x4/4x4 EFT Model Number A2009IDG2BETR (Red - 2x4) Model Number A2009IDG2BETZ (Cat Green - 2x4) Model Number A2009IDG4BETR (Red - 4x4) Model Number A2009IDG4BETG (Green - 4x4)
ENGINE COOLING SYSTEM
B ENGINE A SECTION ENGINE COOLING SYSTEM CO C D CONTENTS E PRECAUTIONS... 2 Precautions for Liquid Gasket... 2 REMOVAL OF LIQUID GASKET SEALING... 2 LIQUID GASKET APPLICATION PROCEDURE... 2 PREPARATION...
Remote Air Cleaner. Assembly Instructions. Assembly Instructions. Before You Start. General Information. Further Assistance
Remote Air Cleaner Assembly Instructions Accu-Z Z52, Z60 & Z72 Zero Turn Mower Before You Start Assembly Instructions Manual No. 356-542M! When you see this symbol, the subsequent instructions and warnings
HIRTH 3203 Carburated - 65 hp
HIRTH 3203 Carburated - 65 hp 2706-65Hp engine shown with fan cooling HIRTH s most popular engine. The 3203 produces more horsepower and torque per pound than any other engine in its power class. Hirth
DTC P0657 Actuator Supply Voltage Circuit / Open
1GR-FE EINE CONTROL SYSTEM SFI SYSTEM 277 DTC P0657 Actuator Supply Voltage Circuit / Open MONITOR DCRIPTION The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the
Motorcycle Carburetor Theory 101
Motorcycle Carburetor Theory 101 Motorcycle carburetors look very complex, but with a little theory, you can tune your bike for maximum performance. All carburetors work under the basic principle of atmospheric
CRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1988 Jeep Cherokee 1988 Cruise Control Systems JEEP CRUISE COMMAND All Models DESCRIPTION & OPERATION Jeep vehicles use an electro-mechanical servo system. The system consists of
INSTRUCTIONS 1kW Propane Autonomous Power Unit Kit
1kW Propane Autonomous Power Unit Kit PLEASE READ THESE INSTRUCTIONS IN THEIR ENTIRETY BEFORE OPERATING YOUR 1KW PROPANE AUTONOMOUS POWER UNIT Introduction The generator provided by NRG Systems has been
Simple Carburettor Fuel System for a Piston Engine. And how it works
Simple Carburettor Fuel System for a Piston Engine And how it works Inlet Exhaust Tank PISTON ENGINE Carburettor Fuel System Filler Cap COCKPIT FUEL GAUGE E FUEL 1/2 F Filler Neck Tank Cavity FUEL LEVEL
Illustrated Parts List. Model Series 31Q700. TYPE NUMBERS 0036 Through TABLE OF CONTENTS
Illustrated Parts List Model Series 31Q700 TYPE NUMBERS 0036 Through 3136. TABLE OF CONTENTS FORM MS5767 REV P 05/17/2012 REPLACES FORM MS5767 REV M 01/16/2012 FILE IN SECT. 2 OF SERVICE MANUAL 31Q700
DTC P0171, P0172, P0174, or P0175
Page 1 of 6 2009 Pontiac G8 G8 Service Manual Document ID: 2076050 DTC P0171, P0172, P0174, or P0175 Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic
DLE-35RA. Operator s Manual. Specifications. Displacement: Performance: Idle Speed: Ignition Style: Recommended Propellers: Spark Plug Type:
DLE-35RA Operator s Manual Specifications Displacement: Performance: Idle Speed: Ignition Style: Recommended Propellers: Spark Plug Type: Diameter Stroke: Compression Ratio: Carburetor: Weight: Fuel: 34.5cc
Thompson Performance, LLC - POWERBLAST PLATE
Thompson Performance, LLC - POWERBLAST PLATE INSTALLATION INSTRUCTIONS FOR PBP EC-56 AND PBP EC-78 IMPORTANT NOTE: Proper installation and safe use of the POWERBLAST PLATE is the responsibility of the
INTAKE AIR TEMPERATURE SENSOR (IAT)
INTAKE AIR TEMPERATURE SENSOR (IAT) 4.8 Refer to the ELECTRICAL DIAGNOSTIC MANUAL for information on the function and testing of the intake air temperature sensor (IAT sensor). sm054 To prevent accidental
ACCELERATOR CABLE AND PEDAL
17 ENGINE & EMISSION CONTROL 1996 Engine Control System ACCELERATOR CABLE AND PEDAL REMOVAL AND INSTALLATION Post-installation Operation (Refer to Adjusting the Accelerator Cable.)
Днепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling
Ural (Урал( Урал) - Dnepr (Днепр( Днепр) Russian Motorcycle Carburetors Part 2B: PZ-24 and PZ-28 Carburetor Assembly and Jet Drilling (applies also to K-37 K and K-38 K carbs) Ernie Franke eafranke@tampabay.rr.com
ENGINE <6G7> Click on the applicable bookmark to selected the required model year.
ENGINE Click on the applicable bookmark to selected the required model year. 11A-2 ENGINE CONTENTS GENERAL INFORMATION... 3 SERVICE SPECIFICATIONS... 3 SEALANT... 4 SPECIAL TOOLS... 4 ON-VEHICLE
GROUP 11B 11B-1 CONTENTS SPECIAL TOOLS... 11B-2 CYLINDER HEAD AND VALVES... 11B-28 GENERATOR AND DRIVE BELT... 11B-4 OIL PAN AND OIL PUMP...
11B-1 GROUP 11B CONTENTS SPECIAL TOOLS 11B-2 GENERATOR AND DRIVE BELT 11B-4 REMOVAL AND INSTALLATION 11B-4 INTAKE MANIFOLD PLENUM AND THROTTLE BODY ASSEMBLY 11B-6 INTAKE MANIFOLD PLENUM REMOVAL AND INSTALLATION
Tuning A Walbro Carb. Walbro Carb TUNE UP & Illustrated Guide
Tuning A Walbro Carb Walbro Carb TUNE UP & Illustrated Guide by M. B. Fuess Walbro carbs aren t too difficult to tune up if you know what you re doing. First of all, you need to know how the carb works
Replacing the camshaft seals / variable valve timing (VVT) unit
"VCC097794 EN 20110521" 1(10) Replacing the camshaft seals / variable valve timing (VVT) unit Special tools: 951 2050, 999 5450, 999 5451, 999 5452, 999 5651, 999 5718, 999 5719, 999 5919 Note! As the
ATV 50 Y-6 YOUTH CAT GREEN (A2004ATA2BUSZ) Page 1 of 50 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY
2004 ATV 50 Y-6 YOUTH CAT GREEN (A2004ATA2BUSZ) Page 1 of 50 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY 2004 ATV 50 Y-6 YOUTH CAT GREEN (A2004ATA2BUSZ) Page 2 of 50 A-ARM, FLOOR PANEL, AND BUMPER ASSEMBLY
PERFORMANCE CARBURETOR INSTALLATION AND ADJUSTMENT INSTRUCTIONS
PERFORMANCE CARBURETOR INSTALLATION AND ADJUSTMENT INSTRUCTIONS Read instructions thoroughly before, during, and after installation. NOTE: This carburetor is for use on Motor Vehicle Applications Only!
BoonDocker Nitrous System Installation Instructions for Kawasaki KFX-700 ATV
BoonDocker Nitrous System Installation Instructions for Kawasaki KFX-700 ATV Before you begin, please read the instructions below and check kit contents Nitrous Kit Contents: 1 Nitrous Manifold with fittings
No part of this publication may be reproduced without written permission.
Thank you for purchasing a Honda generator. This manual covers operation and maintenance of the EB3000 and EB4000 generators. All information in this publication is based on the latest product information
Illustrated Parts List. Model Series. TYPE NUMBERS 0001 through TABLE OF CONTENTS
Illustrated Parts List Model Series 215800 TYPE NUMBERS 0001 through 4529. TABLE OF CONTENTS FORM MS5497 REV R 12/19/2014 REPLACES FORM MS5497 REV P 10/30/2012 FILE IN SECT. 2 OF SERVICE MANUAL 215800