Current Range Rover Sport STRUT Collection Installation Manual
|
|
- Joy Welch
- 6 years ago
- Views:
Transcription
1 Current Range Rover Sport STRUT Collection Installation Manual 1
2 1. Removing Main Grille and Lower Fascia 1.1 Run a line of low tack masking tape across the front of the bumper below the grille to prevent any accidental damage to paintwork. 1.2 Open the hood and then remove 4 screws clip (may be push clips) across top of main grille assembly. 1.3 Gently pull the top of the grille forward, locate the 4 spring clips securing the back of the grille to the bumper and carefully pry loose using a large flat blade screwdriver. The image to the left shows the locations of 4 clips behind the grille. The image to the right shows how to pry off the clip with a large flat blade screwdriver 2
3 1.4 Pull upper grille forward and gently remove. 1.5 Remove 3 of the 4 small hex head screws across the inside lip of the front of the bumper assembly. Note, the 4 th (far left) stays in place to hold the bumper in place. NOTE: Leave far left hex head screw in place to secure front bumper while working on the driver s side bumper grille. This will be removed later to work on passenger s side bumper grille (Once far right screw is refitted). NOTE: For main grille only installation jump directly to section Laying under the front of the car, remove the 4 large plastic flat screw clips from the center lower fascia assembly, then gently pull forward and remove. 3
4 1.7 Laying under the car, remove the 6 center star head bolts (2 at front, 4 set back) and 4 outer (2 per side) Philips head screws. 2 front star head bolts 4 rear star head bolts 2 Philips head screws on each side in front of wheels 2. Installing STRUT Bumper Grilles Driver s Side 2.1 Start the vehicle and turn the steering wheel full lock to right so that the driver s side wheel facing inward. *Note: alternatively front wheels can be removed if using a lift. 2.2 Remove the two Philips head screws from the front inner wheel well and remove the plastic clip from the top of the front inner wheel well. Then gently pull back the plastic wheel well liner, carefully unhooking it from the inside of the fender. Carefully unhook the plastic wheel well liner from along the inner lip of the fender 2.3 Remove the two Philips head screws from inside of the front bumper. 4
5 2.4 Loosen (Do not remove) the two hex head bolts from inside wheel well along the seam where the bumper joins the fender. Loose the two bolts underneath the two captured nuts shown here 2.5 Gently pull the corner of the bumper out from the seam of the front fender, unclipping the 4 plastic clips along the inside lip. 2.6 With the corner of the bumper sitting proud of the fender, remove the two Allen head bolts from behind the bumper grille assembly. Remove the two outer Allen head bolts, do not remove any of the center screws in the assembly 5
6 2.7 Release the 4 plastic tabs from behind the center light cover of the bumper grille assembly and gently pull forward. Note only the center light cover is removed. The outer grille piece and light remain in place. 2.8 Take the STRUT driver s side lower grille assembly and slide threaded shafts through the two existing holes in the bumper grille. Note: Check that the spacer nuts on the threaded shafts are making contact with the mounting plastic on the bumper and ensure precision and flush fitment. Adjust accordingly. 2.9 Install nuts onto back of threaded rods, checking alignment and fitment Refit front bumper and wheel liner by reversing steps: 2.5, 2.4, 2.3, 2.2 and Replace the far right hand hex head screw on the inside lip of the bumper, then remove the far left hex screw. Replace the far right hex head bolt Then remove the far left hex head bolt Leave the two center bolts out at this stage Start engine, turn steering wheel to opposite lock and repeat all steps in section 2 on passenger side. 6
7 3. Installing STRUT Main Grille and refitting lower fascia NOTE: For LED Installation see section 7 before proceeding. 3.1 Carefully align STRUT grille with front bumper, ensuring 4 rear plastic clips on rear of grille align with slots on bumper, then push firmly to locate clips. 3.2 Replace the 4 plastic screw clips across the top of STRUT grille. Replace the 4 screw clips then remove tape from along front lip of grille 3.3 Reinstall the lower fascia by reversing steps 1.6 and front star head bolts 4 rear star head bolts 2 Philips head screws on each side in front of wheels 7
8 4. Installing STRUT Side Vents 4.1 Using a plastic paint scraper carefully pry off side vent, starting at the top right hand corner and easing out clips. Tip: Wrap the end of the paint scraper with masking tape and tape along edge of joint to avoid paint damage. 4.2 Below is a picture of how you will receive the STRUT side vents. To begin install remove side ventmounting bracket by removing 2 top screws and 1 bottom screw. Screws to remove to detach the side vent-mounting bracket 4.3 Install the side vent-mounting bracket behind fender using supplied Philips head screws. There are 3 mounting locations; 2 at the top of the bracket and 1 at the bottom corner. 8
9 4.4 Hold the fiberglass side vent up to the fender aligning the holes attached to the side vent with the 2 holes in the bracket attached to the fender. Once alignment is perfect remove backing from double sided tape. (STRUT suggests using the supplied double sided tape on dealer show room collections but once sold remove parts and replace double sided tape with silicone.) Tip: If the side vent needs to move forward or back to fit in the fender properly there is play in the top of the small side vent molding bracket. 4.5 Using the 2 supplied screws and a Philips head screw driver place screws through mesh and 2 brackets and tighten. 9
10 4.6 Remove backing from double sided tape on side vent extension. (STRUT suggests using the supplied double sided tape on dealer show room collections but once sold remove parts and replace double sided tape with silicone.) 4.7 Using a straight edge, carefully align the top edge of the extension with the main side grille assembly, also ensuring alignment with the door gap before allowing the tape to make contact with the door. 4.8 Check alignment alongside of vehicle and door clearance during opening before pressing on firmly. 4.9 Repeat steps 4.1 through 4.8 on the other side. 10
11 5. Installing STRUT Hood Vents 5.1 Using a plastic paint scraper, gently pry up front corner of vent and lift out. 5.2 Remove 3 of the OEM spring clips from the back of the factory hood vent, being careful not to bend or damage them, then refit them onto the back of the STRUT side vent. 5.3 Ensure the area under the grille is clean and then align the 3 clips and push the STRUT hood vent into place. Tip 1: Use supplied doublesided tape under corners of STRUT hood grille for ultrahigh integrity installation. (STRUT suggests using the supplied double sided tape on dealer show room collections but once sold remove parts and replace double sided tape with silicone.) 5.4 Repeat steps 5.1, 5.2 and 5.3 on the other side. Tip 2: When installing on light colored vehicles use the vinyl black decals to apply to the car before installing the hood vent 11
12 6. Installing STRUT Lift Gate Fascia 6.1 Using medium weight fishing line, gently pull through behind decals on both sides of rear lift gate and remove. Clean off any remnants of adhesive using a non-abrasive, paint-safe cleaner such as Goof Off, and then remove any wax or oils with Isopropyl Alcohol (rubbing alcohol). 6.2 Remove backing from double sided tape from STRUT Lift Gate Fascia, then carefully align top edge of side piece with trim and gently lower ensuring edges are straight and gaps are even. Press on firmly. (STRUT suggests using the supplied double sided tape on dealer show room collections but once sold remove parts and replace double sided tape with silicone.) 6.3 Repeat steps 6.1 and 6.2 on the other side. 7. Installing STRUT LED Kit 7.1 Remove 3 thumbscrews retaining front plastic cover on passenger side at front of engine bay and lift off. 12
13 7.2 Feed the wiring loom (bare wire and eye connector end) from front left side next to the horn assembly through the gap next to the radiator cowl until there is approximately 18 remaining at front of vehicle. Remainder of wire should be directly behind passenger side headlight. 7.3 Remove ground terminal from passenger side engine bay and feed through the eye connector of STRUT LED wiring loom, refit and retighten. 7.4 Unplug multi-pin plug from back of passenger side headlight. Using a razor blade, gently cut along and peel back approx. 2 of outer insulation, being careful not to cut through insulation on wires. 13
14 7.5 Locate purple and orange wire in loom and fit pass-through side of supplied wire joiner over it. 7.6 Feed red wire of STRUT wiring loom into blind side of wire connector and then clamp on splicing terminal with needle nose pliers and then close plastic insulator. 7.7 Re-plug headlight multi-pin plug. 14
15 7.8 Plug two connectors at end of STRUT loom into connectors on back of STRUT grille. Turn headlights to on position and check that both LED strips are both working. 7.9 Replace plastic cover and refit thumbscrews. 15
Lexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015-16 Lexus NX Fine Mesh and Dynamic Radar Cruise Control Fine Mesh Grilles Upper Insert - factory chrome surround and emblem reused
More information1. Front Fascia Removal 1.1 Remove the 6 plastic clips that secure the upper valance, then remove. 1.2 Remove 6 upper bolts that hold the grille and f
STRUT 2015 GMC Denali Collection Installation Manual " 1. Front Fascia Removal 1.1 Remove the 6 plastic clips that secure the upper valance, then remove. 1.2 Remove 6 upper bolts that hold the grille and
More informationUpper Class Grille. Main Grille - # / # Dodge Charger. GRILLE Installation Guide. Parts included (1) Main Grille.
Main Grille - # 51480 / #54480 Parts included (1) Main Grille Polished - Part #51480 OR Black - Part #54480 Hardware included (8) - 3/4 x 5/8 L Brackets (8) - #6-32 Nylon Nuts (8) - 3/16 x 1 x 1/32 Black
More informationLexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2013-15 Lexus ES Fine Mesh and Adaptive Cruise Control Fine Mesh Grilles Upper and Lower Replacements Part #1372-0102-13 / Black Ice
More informationInstallation Instructions Road Defender Push Bumper Part # L Ford Sedan Police Interceptor
Installation Instructions Road Defender Push Bumper Part # 5039-2L51 2013-2015 Ford Sedan Police Interceptor Do not attempt to install this product on any vehicle other than the one listed above! Parts
More informationParts List DAKAR PRO Brackets Part # Chevrolet Silverado /4WD
Installation Instructions BR5 Front Bumper Replacement Part Number 24128T Ram 1500 2/4WD (Not compatible with ParkSense, Sport, Express and Rebel Models) Parts List DAKAR PRO Brackets Part # 524765 2014
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More information05 09 Mustang Squirter Nozzle Relocation Kit CDC #112050
05 09 Mustang Squirter Nozzle Relocation Kit CDC #112050 Note: Read installation instructions before starting. Component Check List: Quantity/Description Part# CDC Installer 2 - Squirter Nozzles 115063
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 2009 Toyota RAV-4 Stainless Steel Mesh Grilles L 30 G8P Fine Mesh Part #30-002-09 Quantity Description Part No. Upper Mesh Grille (includes):
More informationDriver/left Corner Fill Panel. Passenger/Right Corner Fill Panel Left and Right Bar Light L Brackets. (2) Plastic Plugs. License Plate Bracket
LD1 FRONT BUMPER PART#R102615 R102618 PARTS LIST: 1 LD1 Bumper Assembly 8 10mm Lock Washers 1 Driver/left Frame Mounting Bracket 8 10mm Hex Nuts 1 Passenger/right Frame Mounting Bracket 2 8-1.25mm x 25mm
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER 2018 FORD F150
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 28 12mm x 37mm x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 4 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 12
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD SILVERADO 1500 PART #
INSTALLATION INSTRUCTIONS PART # 3-5863 4-0863 PARTS LIST: Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24642 BODY SIDE CLADDING 2003 CR-V P/N 08P21-S9A-100 Issue Date OCT 2002 PARTS LIST Right rear bumper piece Right front fender piece
More information05 09 Mustang Squirter Nozzle Relocation Kit CDC #112050
CD4II3BC 05 09 Mustang Squirter Nozzle Relocation Kit CDC #112050 Note: Read installation instructions before starting. Component Check List: Quantity/Description Part# CDC Installer 2 - Squirter Nozzles
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335i/xi without stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0921 APPLICATION 2007-08 E92 335i/xi without stock oil cooler Congratulations for being selective enough to use a Dinan Engineering Oil Cooler
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationPARTS LIST: ELEVATION BULL NOSE FRONT BUMPER FORD SUPERDUTY F
PARTS LIST: 1 Elevation Bumper Assembly 2 8-1.25mm x 25mm Hex Bolts 1 Winch Tray Bracket Assembly 2 8-1.25mm x 16mm Hex Bolts 2 3-hole Bracket Spacer Plates 6 8mm x 24mm x 2mm Flat Washers 2 Plastic Plugs
More informationLeft and Right Bar Light L Brackets. Driver/Left Frame Bracket
PARTS LIST: 1 Bumper 14 12mm Nylon Lock Nuts 1 Bull Nose Hoop 2 10mm Double Bolt Plates 1 Winch Tray 4 10-1.5mm x 25mm Hex Bolts 1 Driver/left Frame Mounting Bracket 8 10mm x 30mm x 2.5mm Flat Washers
More information* APPLICATION MODELS VARY. WE RECOMMEND TO VERIFY FITMENT BEFORE BEGINNING INSTALLATION PROCESS.
Parts included (1) Main Grille Polished - Part #6214760 OR Black - Part #6214761 Hardware included (8) - #8 x 3/4 Black Screws (8) - #8 Flat Nuts (3) Push Nut Retainer Clips START HERE PLEASE READ AND
More informationC15C C15C. Page 1 of 20
2 x Lid Front Hinge 1135 8 x M8 Bolt 8 x M8 Washer (3mm Thick) 4 x M6 Large washers 4 x M6 Spring washers 4 x M6 x 40mm Bolts 6 x M6 20mm Bolts 6 x M6 Washers 20 x Screws 2 x Lid mount gas strut bracket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. FENDER FLARES P/N 08P21-S3V-200 2003 MDX BII 24553 Issue Date SEP 2002 PARTS LIST Right rear fender flare Left front fender flare Right
More informationINSTALLATION INSTRUCTIONS ARMOUR FRONT BUMPER W/O LED LIGHTS FOR CHEVY COLORADO PART # AFB-CO15
INSTALLATION INSTRUCTIONS ARMOUR FRONT BUMPER W/O LED LIGHTS FOR CHEVY COLORADO 15-17 PART # AFB-CO15 ARMOUR FRONT BUMPER PARTS LIST: 1 ARMOUR Bumper Assembly 2 8mm x 25mm Hex Bolts 1 Driver/left Frame
More informationINSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17
AEV30304AA Last Updated: 09/18/17 PREMIUM FRONT BUMPER FOR RAM 1500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START To guarantee a quality installation, we recommend reading these instructions thoroughly
More informationSAFETY SENSORS FIELD OF VIEW WILL BE ALTERED WITH USE OF THE REPLACEMENT BUMPER. Injury hazard
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION GUIDE Front Bumper. KL Cherokee (Trailhawk)
INSTALLATION GUIDE Front Bumper KL Cherokee (Trailhawk) Included Hardware: Sample Sample Sample Skill Level: 5/5 stars (Professional install recommended) Disclaimer Expedition One is not responsible for
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD GMC SIERRA 1500 EXCLUDES DENALI PART # 4084/
INSTALLATION INSTRUCTIONS GRILLE GUARD 14-15 GMC SIERRA 1500 PART # 4084/ 4084-2 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4
More informationPassenger/Right Top Support Bracket. (2) 10mm Nut Plates
PARTS LIST: 1 Extreme Grille Guard 16 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 10 12mm Lock Washers 1 Passenger/Right Frame Mounting Bracket 10 12mm Hex Nuts 1 Driver/Left
More informationSubaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More information(W) INSTALLATION INSTRUCTIONS GRILLE GUARD 2014 GMC SIERRA 1500 EXCLUDES DENALI PART # /
(W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 508514/ 508515 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm
More informationLPE C5 Battery Relocation Kit
LPE C5 Battery Relocation Kit The LPE C5 Corvette battery relocation kit improves vehicle weight distribution by moving weight to the rear of the vehicle. The improved weight distribution increases traction
More informationTools Required. Metric Wrench Set Screwdriver Set Metric Socket Set Pliers Heavy duty hydraulic Jack and Car Stands Box knife or similar Hacksaw WD40
Subaru 2004+ Legacy GT & Outback XT For JDM 2.0 twinscroll turbo and USDM 2.5 turbo models Front Mount Intercooler Fitting Instructions PN# LEG-1348-000 You are now the proud owner of a highly tested and
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationRight Bar Light L Bracket Left Bar Light L Bracket. License Plate Bracket
LD1 FRONT BUMPER PART#R102616 R102619 PARTS LIST: 1 LD1 Bumper Assembly 16 10mm x 27mm OD x 3mm Flat Washers 1 Driver/left Frame Mounting Bracket 8 10mm Lock Washers 1 Passenger/right Frame Mounting Bracket
More information2015 Ford F150 Rear Bumper w/ LED
2015 Ford F150 Bumper w/ LED T527990 T527991 PARTS LIST: 1 Bumper Assembly 4 12mm Lock Washers 2 Mounting Brackets 6 12 mm Nylon Lock Nuts 4 Sensor Hole Plugs 8 4mm x 10mm Button Head Bolts 2 Plastic Plugs
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationLD1 FRONT BUMPER GMC SIERRA 1500
LDB-GSIE52-FB PARTS LIST: 1 LD1 Bumper Assembly 6 12mm Lock Washers 1 Driver/left Frame Mounting Bracket 6 12mm Hex Nuts 1 Passenger/right Frame Mounting Bracket 6 10-1.5mm x 35mm Hex Bolts 2 Tow Hook
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC. INSTALLATION INSTRUCTIONS APPLICATION: DODGE CHARGER POLICE PUSH BAR (2011 & UP) APP PART # 36-2035 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 PUSH BAR ASSEMBLY RATCHET 2,3 2
More informationSHELBY GT500
2007-2009 SHELBY GT500 Removal of Factory Unit WARNING: 1. Radiator fluid must be handled properly. Please observe local ordinances with regards to handling and disposal. 2. Allow vehicle and components
More informationHD BULL NOSE FRONT BUMPER FORD SUPERDUTY F PARTS LIST:
PARTS LIST: 1 HD Bull Nose Bumper Assembly 1 Bumper Cover 1 Winch Tray Bracket Assembly 5 6mm Combo Button Head Bolts (cover) 2 3-hole Bracket Spacer Plates 1 Wrench (6mm Button Head) 2 Plastic Plugs for
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 33322-36889 UNDER 2007 TL Issue Date MAY 2007 PARTS LIST Front under spoiler Left bracket (Marked L ) Right bracket (Marked R ) 8 Self-tapping
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationREVOLVER SERIES GRILLES - INSTALLATION GUIDE
REVOLVER SERIES GRILLES - INSTALLATION GUIDE Depending on your style and your preferred look of the vehicle, you have the option to install the Raw Aluminum Trim Piece, Color Match, or just opt to leave
More informationMustang Shaker
2005-2009 Mustang Shaker CDC #110050 ( 05/ 06) or 0711-7000-01 ( 07/ 09) Component Check List: Quantity/Description Part # CDC Installer 1 - Engine Cover Assembly 114050 1 - Aluminum Shaker Scoop 183020
More informationFitting Instructions. Revo MQB Golf/GTi/Octavia/Leon Intercooler. Recommended Tools. Contents RV581M Dealer installation advised.
RV581M100100 Recommended Tools Contents No. Description Tools Size Intercooler Torx Bit T25, T30 Bracket Kit llen Key 4, 5 mm Silicone Hoses Socket 7, 10, 16, 19 mm Hose Clamps Flat Head Screwdriver Small,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REAR SPOILER Application 2011 CR-Z MUGEN Publications No. AII 45919 Issue Date APRIL 2011 PARTS LIST Right wing bracket Rear wing Left wing bracket Right wing base Right
More informationIMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015 Nissan Murano. Upper and Lower Overlay Mesh Grilles
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2015 Nissan Murano Upper and Lower Overlay Mesh Grilles Upper Chrome Mesh Part #1318-010U-15 / Lower Chrome Mesh Part #1318-010L-15
More informationMAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS
MAZDA BT-50 (October 0 Production Onwards) & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS Installation Time: Approx. 0 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent
More informationIMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2014-15 Toyota Tundra Mesh Grille Upper Insert - Fits ALL model Tundras with chrome or painted factory grille surround Black Mesh Part
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. 2009 CIVIC HYBRID All 40191 Issue Date AUG 2008 PARTS LIST Rear under spoiler 2 Step bolts 4 Self-tapping screws TOOLS REQUIRED Phillips
More informationInstallation instructions, accessories. Body kit
Installation instructions, accessories Instruction No 31265373 Version 1.1 5 Part. No. Body kit IMG-256263 Volvo Car Corporation Body kit - 31265373 - V1.1 Page 1 / 42 Equipment A0000162 A0000163 IMG-239664
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD TOYOTA TUNDRA TOYOTA SEQUOIA PART # P2067
INSTALLATION INSTRUCTIONS GRILLE GUARD 07-14 TOYOTA TUNDRA 08-14 TOYOTA SEQUOIA PART # P2067 PARTS LIST: GRILLE GUARD 1 Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More informationINTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D
INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D330-0021 APPLICATION: 2014-16 F22 228i & xdrive coupe (see restrictions below) 2015-16 F23 228i & xdrive convertible 2012-16 F30 328i & xdrive
More informationPart Number: TTU-BGB14-DRL TTU-BGP14-DRL
11/15/16 TOYOTA TUNDRA 2014-17 Billet Grille w/led DRL Part Number: TTU-BGB14-DRL TTU-BGP14-DRL Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Switch 4 1 User Card 5 2 Hardware
More information54531/ FORD FUSION
54531/51531 54531/51531 13-15 FORD FUSION 13-15 FORD FUSION FORD FUSION Upper Class Grille w/ Bars TOOLS REQUIRED: Socket Set Flat/Phillips Screw Drivers Torx Bits Plastic Pry Bar 3/16 Drill Bit and Drill
More informationAggressive Chin Spoiler CDC#
Note: 2005-2009 Aggressive Chin Spoiler CDC# 110021 Read installation instructions before starting and test fit component before painting. Chin Spoiler is a molded Urethane part. To ensure the quality
More informationINTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D
INTERCOOLER UPGRADE INSTALLATION INSTRUCTIONS PART NUMBER D330-0021 APPLICATION: 2014-16 F22 228i & xdrive coupe (see restrictions below) 2012-16 F30 328i & xdrive sedan 2014-16 F31 328i xdrive wagon 2014-16
More informationInstallation Instructions Page 1 of 10
Page 1 of 10 PART NUMBER: APPLICATION: 203.67.2501, 203.67.2503 HONKER C6 2006-13 CORVETTE Z06, AIR INDUCTION SYSTEM 2008-13 CORVETTE LS3 INSTRUCTION SHEET NUMBER: WITH DIFFUSER PANEL 903.67.9852A without
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2011 Dodge Charger Road Defender 5000 Series Push Bumper Part Number 5076 Do not attempt to install this product on any vehicle other than the one it is designed for and listed
More informationInstallation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD
Installation instruction do88 Intercooler for SAAB 9-3 1,9 TTiD This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always recommend
More information2. With the rear door open remove pull-style clip from the passenger side just below the door latch.
LoD Offroad FJ Cruiser Rear Bumper with Tire Carrier Installation Instructions 1. Begin with removing factory spare from the rear door. 2. With the rear door open remove pull-style clip from the passenger
More information2011 Cadillac CTS Coupe EGX Exhaust Tip & Rear Valance Mesh Accent Kit Part #: Complete E
BILLET GRILLS IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2011 Cadillac CTS Coupe EGX Exhaust Tip & Rear Valance Mesh Accent Kit Part #: Complete 5122-1900-11E TOOLS REQUIRED Automotive
More informationPassenger/Right Top Support Bracket. (4) Spacer Plates (use on models without tow hooks. (2) 12mm x 100mm Double Bolt Plates
GRILLE GUARD PARTS LIST: Qty Description Qty Description 1 Grille Guard 4 12-1.75mm Nylon Lock Nuts 1 Driver/left Frame Mounting Bracket 4 10-1.5mm x 30mm Hex Bolts 1 Passenger/right Frame Mounting Bracket
More information2010 Mustang V6 Shaker CDC #
- - Incomplete 2010 Mustang V6 Shaker CDC # 1011-7002-01 Component Check List: Quantity/Description Part # Engine Cover Assembly 1011-6000-01 1 Engine Cover w/ Upper Air Tube 0511-2100-01 1 Aluminum Shaker
More informationInstallation Instructions BR20 Rear Bumper Replacement Part # 28178T Toyo ta Tundra 2/4WD
Installation Instructions BR20 Rear Bumper Replacement Part # 28178T 2014-2016 Toyo ta Tundra 2/4WD Excludes Models with B lind Spot Monitoring & Cross Traffic Alert Parts List Item Qty. Part # Description
More informationGMC Yukon
Torch Series LED Grille TOOLS REQUIRED: Flat Head Screwdriver Long Flat Head Screwdriver Phillips Screwdriver 7mm Socket 10mm Socket Ratchet & Extensions 3/16 Drill Bit Power Drill Cutting Wheel or Saw
More informationH15P. Toyota Hilux A-DECK Dual Cab
Toyota Hilux A-DECK Dual Cab Page 1 of 14 Fitting Instructions Part Number H15 Toyota Hilux A-DECK Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More information2007 Current Jeep Wrangler JK Stealth Fighter Front Bumper Installation Instructions
2007 Current Jeep Wrangler JK Stealth Fighter Front Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationSDHQ F-150 Winch Mount System Installation
SDHQ 2015+ F-150 Winch Mount System Installation Recommended Tools: Door panel removal tool Needle Nose Pliers 10mm Socket or Wrench 13 mm or ½ Socket (⅜ Drive) 14 mm or 9/16 Socket (⅜ Drive) 21 mm or
More informationIAG Competition Series Air / Oil Separator (AOS) For 2017 STI
P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92/E93 335i/xi with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0920 APPLICATION 2007-10 E92/E93 335i/xi with stock oil cooler Congratulations for being selective enough to use a Dinan Engineering Oil Cooler
More informationHolden VE/VF Commodore. Over The Radiator Intake. Installation Instruction Guide. VE Infill Panel. VE Hood Insert Panel. Twin Fascia Panels
Holden VE/VF Commodore VE Infill Panel Complete the OEM look by covering the hole left after removal of the factory Airbox. Over The Radiator Intake Installation Instruction Guide VE Hood Insert Panel
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D A. APPLICATION: E36/7 M-Roadster or M-Coupe 3.
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0323A APPLICATION: 1998-00 E36/7 M-Roadster or M-Coupe 3.2 Liter PARTS LIST Air Filter Assembly 3 1/2" Tube Intake Shield Silicone Hose Airflow
More informationECO-SERIES FRONT BUMPER FOR GM SIERRA #GM-19337
#GM-19337 Body Armor 4x4 272 Corporate Terrace St. Corona, CA 92879 951-808-0750 Customer Service hours: M-TH: 7:30am to 4:30 PM Pacific Time Friday: 8 AM Noon Pacific Time PARTS LIST: 1 LD1 Bumper Assembly
More informationToyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Transmission cooler relocation brackets Torque Wrench
2016-2017 Toyota Tacoma Winch Mount Bumper Installation Instructions Tools Required: Items Included: Small flat head screw driver Winch Mount Ratchet, 10mm, 12mm, 14mm, 17mm & Skid Plate 19mm sockets Transmission
More informationConflicts None. TOYOTA TUNDRA 2017 Black Laser Cut Grille. Part Number: Accessory Code: BG3000. General Applicability
TOYOTA TUNDRA 2017 Black Laser Cut Grille Part Number: 00016-34173 Accessory Code: BG3000 Conflicts None Kit Contents Item # Quantity Reqd. Description 1 1 Laser Cut Grille 2 1 Complete hardware kit General
More informationFront Grille Replacement
Document ID: 4298678 Page 1 of 1 2017 Cadillac XT5 XT5 Service Manual Europe, Korea, N America, Other IO 9325297 Document ID: 4298678 Front Grille Replacement Front Grille Replacement Preliminary Front
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationWARNING TAKE NOTE OF THE FOLLOWING: THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS USING ONLY THE HARDWARE SUPPLIED.
ARB WINCH/NONWINCH BUMPER TO SUIT TOYOTA HJ100 IFS PRODUCT No. 3913140 5100050 Top Tube Kit 5100160 Buffer Kit With hole (required when fitting Top Tube) 5100170 Buffer Kit With no hole Fitting Kit No.
More informationLAND ROVER DISCOVERY 3 ARB BULL BAR AND WINCH BAR WARNING
LAND ROVER DISCOVERY 3 ARB BULL BAR AND WINCH BAR PART No 3432150 DISCOVERY 3 WINCH BAR PART No 3232150 DISCOVERY 3 BULL BAR WARNING FOR VEHICLES EQUIPPED WITH SRS AIRBAG WHEN INSTALLED IN ACCORDANCE WITH
More information(2) 10mm Quick Release Bolts with Pivot Washers (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts. (4) 10mm Plastic Washers
PARTS LIST: EXTREME GRILLE GUARD 1 Extreme Heavy Duty Grille Guard 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 1 Driver/left Frame Mounting Bracket 4 10mm x 24mm OD x 2.2mm Flat Washers
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT-CARBON FIBER REAR SPOILER INFINITI Q50 T99J1 J5000 KIT CONTENTS: Item A B C D Qty. 1 4 1 1 Part Description Spoiler Assembly
More informationZ1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual
Z1 Motorsports 2877 Carrollton Villa Rica Hwy Carrollton GA 30116 770.838.7777 Z1 Motorsports 350Z / G35 Oil Cooler Kit Installation Manual For 19, 25 and 34 Row Oil Cooler Kits Parts Included: 1 Aluminum
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS OUTLAW FRONT BUMPER APPLICATION: 2016-2018 Chevrolet Silverado 1500 PART NUMBER: 58-61005 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 FRONT BUMPER ASSEMBLY 18MM WRENCH
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More information(1) License Plate Light (2) License Plate Plugs
PARTS LIST: 1 HD Replacement Bumper 4 12mm x 40mm Hex Bolts 1 Driver/Left Bracket 4 12mm Nylon Lock Nuts 1 Passenger/Right Bracket 8 12mm x 37mm x 3mm Oversize Flat Washers 2 Thin Side Spacers 4 Rubber
More informationPart Numbers: TTU-BGP14 & TTU-BGB14
Date: 10.14.2015 TOYOTA TUNDRA 2014-17 Billet Grille Part Numbers: TTU-BGP14 & TTU-BGB14 Grille Hardware Bag Contents Item # Quantity. Description 1 6 U-Nuts 2 8 #10 Screws 3 2 #8 Screws 4 2 2 Flange Brackets
More informationRS5mesh style Grille. Audi A5/S5. Installation Instructions. pre-facelift ES best viewed in Acrobat Reader
Audi A5/S5 pre-facelift RS5mesh style Grille Installation Instructions ES2627648 This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures
More informationInstallation Instructions for Lingenfelter GM 2500 Suburban & Yukon XL Auxiliary Fan System (with AC clutch controlled fan output)
Installation Instructions for Lingenfelter 2007-2013 GM 2500 Suburban & Yukon XL Auxiliary Fan System (with AC clutch controlled fan output) PN L300080607 Revision - 1.1 Lingenfelter Performance Engineering
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1.
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-799C (GUN METAL GRAY FINISH) 2014-16 NISSAN SENTRA 1.8L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157D AIR
More informationEXTERIOR TRIM COWL GRILLE REMOVAL/INSTALLATION A3U W01
EXTERIOR TRIM COWL GRILLE REMOVAL/INSTALLATION......... 1 EXTRACTOR CHAMBER REMOVAL/INSTALLATION......... 1 4SD........................... 1 5HB........................... 2 FRONT FLAP REMOVAL/INSTALLATION.........
More informationInstallation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo
Installation instruction do88 Intercooler for SAAB 9-3SS/SC 2,8 V6 Turbo This instruction shows how to replace the OEM intercooler with this performance intercooler. At this type of installation we always
More information20964/B 20964/B 2014 TOYOTA TUNDRA TUNDRA. Billet Grille. Fig 1. Fig 2
Billet Grille TOOLS REQUIRED: PARTS LIST: Socket Set (6) U-Nuts Flat/Phillips Screw Drivers (8) #10 Screws Pliers (2) #8 Screws ¾ (2) 2 Flange Bracket (1) Top Plate Overlay Bracket - driver (1) Top Plate
More informationParts List ILLUSTRATION #1
Installation Instructions BR20 Rear Bumper Replacement Part Number 28171T 2014-2016 Chevrolet Silverado 1500 2/4WD Do not attempt to install this product on any vehicle other than the one listed above!
More information