In Situ Oxygen Transmitter

Transcription

1 Product Data Sheet PDS 340.B01 May, 2010 Oxymitter Now Offered With Xi Advanced Electronics In Situ Oxygen Transmitter Outstanding accuracy Electronics mounted to probe or separate Optional Xi advanced electronics large backlit LCD display advanced software features Wireless - via THUM TM Adaptor Adaptable to any existing O 2 probe installation Advanced sensor diagnostics alarm indicates when calibration is recommended Optional explosion-proof ratings see PDS C01 Digital HART or FOUNDATION fieldbus communications AMS/PlantWeb compatible Fully field-repairable Variable probe insertion option THE LATEST BREAKTHROUGH FOR COMBUSTION FLUE GAS ANALYSIS The Oxymitter In Situ Oxygen Transmitter was the world s first in situ, zirconium oxide-based oxygen transmitter for flue gas measurement. These oxygen measurements can be used in a control system or by a boiler operator to fine tune burner fuel/air ratios for maximum efficiency. Ideal for: boilers process heaters kilns reheat furnaces Emerson Process Management is the leader in oxygen flue gas analyzer technology. Our in situ, zirconium oxide oxygen analyzers have long been established as industry standards. We ve combined our expertise with the latest Rosemount transmitter technology to create a truly revolutionary package the Oxymitter. The Oxymitter integrates an oxygen probe and field electronics into a single, compact package. The probe inserts directly into a flue gas duct to measure oxygen in combustion processes. No sampling system is required. A NEMA 4X, IP 66 Rosemount transmitter housing mounts directly to the probe and contains the transmitter s electronics, replacing common stand-alone field electronics. This integrated design minimizes the costs of installing separate probe cable, conduit and electronics. Wireless THUM TM Adaptor mounts to either electronics Integral or Remote electronics Optional Xi enhanced interface The Oxymitter electronics also require 95% less power to operate. So, its components last longer. Traditional architecture with remote-mounted electronics is also offered. The HART protocol provides a link into Emerson Process Management s PlantWeb field-based architecture. Instrument technicians can interface with the Oxymitter from the control room or any location where the transmitter s signal wires terminate. Service diagnostics and calibrations can be performed remotely with a HART hand-held communicator or a personal computer equipped with AMS. The Oxymitter is fully field-repairable. The probe s design provides convenient access to internal probe components so technicians can service the unit in house. The cell and heater/thermocouple are fully field-replaceable. The Oxymitter contains no potentiometer adjustments or jumpers. The Oxymitter In Situ Oxygen Transmitter operates at process temperatures up to 1300 F (700 C), providing a fast response with high accuracy and reliability. Available lengths from 18 inches to 18 feet. Optional accessories for the Oxymitter include: auto calibration gas sequencer remote, loop-powered Vacuum Fluorescent display of oxygen reading high temperature accessories for temperatures up to 1832 F (1000 C) flame arrestor abrasive shield Visit our website at On-line ordering available.

2 VARIABLE INSERTION OPTION The new varible insertion option permits ideal placement of the probe into the flue gas duct. Probe can be adjusted at any time on-line to characterize stratification across large ducts. THE OXYMITTER OXYGEN TRANSMITTER IS COMPLETELY FIELD-REPAIRABLE Diffusion Filter and Sensor Cell Assembly Outstanding accuracy + or -.75% of reading or.05% O 2 Special cells for tough service in SO 2 and HCL Rugged steel cell holder cells will not crack Heater/Thermocouple Assembly General Purpose OXT4A/5A Lengths from 18 (.9m) to 18 (5.5m) ANSI, DIN and special flanges (1.8m) (5.5m) Flat-faced (snubber), Hastelloy and Ceramic Diffusers Electronics -40 F to 185 F(-40 C to 70 C) ambient temperature limit HART or Foundation fieldbus communications Calibration Recommended diagnostic Integral to Probe or Remote Mounted Xi Enhanced Interface Lowest cost of installation Bright gas fluorescent local operator interface (LOI) Thru-glass infrared pushbuttons are suitable for hazardous areas Page 2 Easy-to-read backlit display Easy-to-use keypad IP66 (NEMA 4X) enclosure Advanced software features Loss of flame relay option turns heater off upon flame loss

3 Advanced Features Automatic Calibration - available with Oxymitter or Xi electronics Plant personnel often ask how frequently an oxygen analyzer requires calibration. The answer is very application-dependent based upon the fuels being burned, normal levels of oxygen and the sulfur content in the flue gases. The X-STREAM Xi addresses this concern by providing an on-line diagnostic that determines when a calibration should be conducted, eliminating many unneeded calibrations and the technician and gas resources they consume. The X-STREAM electronics has an on-line impedance measurement for the sensing cell. This feature can trigger a fully automatic calibration by sequencing solenoids to introduce calibration gases to the sensing cell. The Single Probe Sequencer (SPS) switches CAL gases to a single probe, while a Multi-Probe Sequencer (IMPS) can handle 1 to 4 probes. Many needless calibrations based on time in service are eliminated. A contact closure notifies the control room when a calibration is taking place. The oxygen output signal can be held at its last value, or released during calibration. The X-STREAM can also initiate calibrations by traditional methods: Contact closure from the user s control room Time since last calibration feature established by the autocalibration system Xi enhanced interface HART/AMS Oxymitter or Xi Enhanced Interface and Advanced Feature Electronics Single Probe Sequencer (SPS) Model 375/475 Handheld Communicator Optional Wireless THUM Adaptor Transmit the O 2 signal, along with all HART information. Page 3

4 Advanced Software features (available only with the Xi electronics) Extended Process Temperature Range to 800 C (1562 F) The X-STREAM oxygen analyzer employs a heater and thermocouple to maintain a temperature setpoint at 736 C (1357 F). Temperature control is maintained within ±1 C to process temperatures of about 705 C (1300 F). This is satisfactory for most applications, but excursions to higher temperatures can occur in many processes. In these instances, the heater is turned off and the process temperature is utilized to heat the sensing cell. Stoichiometer Process upsets can sometimes cause a combustion process to go into substoichiometric or reducing conditions. The oxygen readings from one or more probes may decline all the way to zero. The stoichiometer cell will measure the amount of oxygen deficiency during these reducing conditions. The trends in your DCS can be set up for a lower range limit of -1 or -2% oxygen to depict the level of oxygen deficiency. The oxygen reading is adjusted immediately to compensate for the varying process temperatures. It should be noted that cell life will be reduced by continuous operation at temperatures above 705 C (1300 F). If process temperatures are expected to continuously be above 705 C, we recommend the use of a bypass or probe mounting jacket accessory (see page 10). The operator can see if his control actions to recover are having the desired effect. These types of events do not occur frequently, but knowing the parameters of the situation prevents overcorrecting while coming out of the reducing condition. Acid-Resistant Stoichiometer Cell Typical DCS Trend During a Reducing Process Event DCS Trend With X-STREAM Stoichiometer Feature Programmable Reference The zirconium oxide sensing technology has historically measured process oxygen by using ambient or instrument air as a reference (20.95% oxygen). The sensor develops most of its signal at the low oxygen levels typically found in combustion flue gases (2-4% oxygen) and is most accurate at these levels. When measuring at levels near ambient, however, the sensor develops only a few millivolts of signal and accuracy degrades. The programmable reference feature permits the user to use a bottled reference gas of low oxygen value (.4% oxygen recommended). When measuring at or near 21% oxygen, a strong negative oxygen signal results with much improved accuracy. A bottle of reference gas typically lasts about a month at the low flows required. Typical applications include: Flue Gas Recirculation controlling the mixing of flue gases into the burner windbox prior to the burner to reduce NOx emissions. Moisture Monitoring measuring the amount of moisture coming off of industrial dryers by noting the dilution effect water vapor has on the normal 20.95% ambient drying air. Enriched Oxygen Combustion Pure oxygen is sometimes mixed in with the combustion air to increase heat at the flame. This is used in steel and other metals reduction processes and also in some catalyst regenerators. Page 4

5 SPECIFICATIONS 1 Measurement Specifications Net O 2 Range: variable 0-10% to 0-40% (Xi electronics offer 0-50% O 2 range) Accuracy in Oxidizing conditions: ±0.75% of reading or 0.05% O 2, whichever is greater Lowest detectable limit.02% O 2 Process Temperature Effect less than.05% O 2 from C System Speed of Response to Calibration Gas: Calibration Validity: Initial response in less than 3 seconds, T90 in less than 8 seconds. Response to process gas changes will vary, depending on process gas velocity and particulate loading of the diffuser Presentation of calibration gases matches the normal process to within ±.02% O 2 Accuracy in reducing conditions: ±.10% of reading, or.1% O 2, whichever is greater System Response in Reducing Conditions: going from oxidizing to reducing -T90 in 120 sec. going from reducing to oxidizing -T90 in 30 sec. Environmental Specifications Transmitter Probe: Process-wetted materials are 316L or 304 stainless steel Process Temperature Limits: Oxymitter Transmitter Electronics Housing (integral to probe, or remote mounted): General Purpose Certifications: Oxymitter electronics ambient temp. Limits: 0 to 705 C ( F) with Oxymitter electronics 0 to 800 C ( F) with Xi electronics *reduced cell life can be expected if operated continously at tempatures above 705 C (1300 F) optional bypass and jacket accessories permit operation to 1050 C (1922 F) Low copper aluminum IP 66 (NEMA 4X), with reference air exhuast port piped to clean area -40 to 80 C (-40 to 176 F) Temperature limit as measured inside Oxymitter electronics: -40 to 85 C (-40 to 185 F) Temperature limit of see-thru IR pushbuttons: Optional Xi Electronics: -40 to 70 C (-40 to 158 F) NEMA 4X, Polycarbonite Material General Purpose Certifications: Xi Ambient Temp. Limits: Xi Temp. Limits as measured inside the housing: Xi LCD display Temp. Limits: Installation Specifications -20 to 55 C (-4 to 131 F) -20 to 55 C (-4 to 113 F) -20 to 55 C (-4 to 131 F) Probe Mounting Flange: vertical or horizontal 2 150# (4.75 (121mm) bolt circle) DIN (145mm (5.71 ) bolt circle) Note: flanges are flat-faced, and for mounting only. Flanges are not pressure-rated. Spool piece P/N 3D39761G02 is available, to offset electronics housing from hot ductwork. Many adaptor flanges are available to mate to existing flanges. Probe Lengths and Approximate Shipping weights: 18 in. (457 mm) package: 16 pounds (7.3 kg) 3 foot (0.91 m) package: 21 pounds (9.5 kg) 6 foot (1.83 m) package: 27 pounds (12.2 kg) 9 foot (2.74 m) package: 33 pounds (15.0 kg) 12 foot (3.66 m) package: 39 pounds (17.7 kg) 15 foot (4.6 m) package: 45 pounds (20.5 kg) 18 foot (5.5 m) package: 51 pounds (23 kg) Reference Air (optional): Calibration: 2 scfh (1l/m), clean, dry, instrument quality air (20.95% O 2 ), regulated to 2.5 psi (34kPa) Semi-automatic or automatic Cal Gases:.4% O 2 and 8%, balance N 2 recommended Cal Gas Flow: 5 scfh (2.5 l/m) Heater Electrical Power: V, ±10% 50/60 Hz 1/2 14 NPT conduit ports Traditional Architecture Cable: Power Consumption of Probe Heater: Electrical Power of Oxymitter or optional Xi electronics: Power Consumption of Xi: Xi Alarms Relays: Xi Optional Loss of Flame Contact: 200 foot (61m) maximum length 776VA maximum during warm-up 120 to 240V, ±10% 50/60 Hz 10 watts maximum 2 provided - 2 amps, 30 VDC Removes heater power Page 5

6 Electrical Noise: Meets EN 61326, Class A Traditional Architecture Cable: 200ft (61m) maximum length Power Consumption of Probe Heater: 776VA maximum during warm-up Transmitter Electrical Power: 12 42VDC, (loop-powered from the control room or from the Xi box) General Purpose HART communications - OXT4A pg. 11 FOUNDATION Fieldbus Communications - OXT5A pg. 13 Direct Replacement Probe (for use with existing electronics) - OXT4ADR pg. 15 Automatic calibration systems - XSO 2 Cal pg. 16 Optional Xi advanced electronics - Xi pg. 17 Power Supply and Load Requirements Electrictical Power for Xi: Power Consumption of Xi: Alarm Relay Outputs: Optional Loss of Flame Input: V ±10%, 50-60Hz 12VA maximum or 776VA maximum with Traditional Architecture, 120V, Probes. 450VA maximum with Traditional Architecture, 44V Probes Two provided - 2 Amperes, 30 VDO, Form-C internally powered input to remove heater power, actuated via dry contact output from prove of flame device. Emerson Process Management has satisfied all obligations coming from the European legislation to harmonize the product requirements in Europe. 1 All static performance characteristics are with operating variables constant. Specifications subject to change without notice. Page 6

7 OUTLINE DIMENSIONS FOR OXYMITTER OXYGEN TRANSMITTER FOR GENERAL PURPOSE APPLICATIONS (OXT4A, OXT5A, OXT4ADR) Table I. Mounting Plate Dimensions Dia. in. (mm) ANSI DIN JIS Mtg. Plate (x) (153) (190) (165) Stud Size 5/8 11 M16 x 2 M12 x Studs Eq BC 5.71 BC 5.12BC Sp. on BC (121) BC (145) BC (130) BC Flange (Y) (153) (185) (155) Table II. Removal/Installation Dim A Dim. B Probe Insertion Removal Length Depth Envelope 18 in. (457 mm) Probes (407) (725) 3 ft. (0.91 m) Probes (864) (1182) 6 ft. (1.83 m) Probes (1778) (2097) 9 ft. (0.91 m) Probes (2692) (3011) 12 ft. (3.66 m) Probes (3607) (3926) Page 7

8 OXYMITTER 4000 WITH ABRASIVE SHIELD ATMO E R WAV LOSI SP NING- R HE E - VE I AL T I U C CIR WHEN XP - E TI GHT N I - KE P E Notes : 0.2 (5) 3.9 (99) S nubber/dust S eal Assembly Deflector Assy P robe (330) 31 (787) 67 (1702) 103 (2616) 139 (3531) 175 (4445) 211 (5359) (826) 50.5 (1283) 86.5 (2197) (3112) (4026) (4940) (5855) Diffuser/Dust S eal Assy and 7.00 (178) F lange A NS I DI N Flange Dia Hole Dia 9.00 (229) 0.75 (19) 9.25 (235) 0.94 (24) 7.50 (190) 7.48 (190) R emoval 4.77 (121) 6.02 (153) E nvelope (318). G CAL AS R ef ANS I DIN Air C onnection Note: For probes 9 ft. or longer, bracing for cell end of probe is required inside the flue gas ductwork. (Brackets provided with abrasive shield) Page 8

9 OXYMITTER 4000 ADAPTOR PLATE WITH ABRASIVE SHIELD Dimensions in. (mm) ANS I DIN "A" " B" Dia "C " Thread " D" Dia 9.00 (229) 4.75 (121) (191) 9.25 (235) 3.94 (100) 7.48 (190) 22.5 o A A B C Page 9

10 OPTIONAL VARIABLE INSERTION MOUNTING* (OXT4A, OXT5A, OXT4ADR) PROBE SIZE L D X1 ±2 (51) X2 ±2 (51) 9 ft. (2.73) 118 (2997) 18 (457) < D<103 (2616) 72 (1829) 12 ft. (3.64) 154 (3912) 18 (457) < D<139 (3531) 60 (1524) 120 (3948) 15 ft. (4.55) 190 (4826) 18 (457) < D<175 (4445) 70 (1778) 150 (3810) 18 ft. (5.45) 226 (5740) 18 (457) < D<211 (5359) 80 (2032) 160 (4064) Page 10 *Note - cannot be used with abrasion shield, not recommended for highly abrasive flue gases order by part #6A00319G03

11 ORDERING INFORMATION General Purpose Oxymitter with 4-20 ma Output Signal, and HART Communications. Optional Xi electronics not applicable. Model Description OXT4A In Situ Oxygen Transmitter HART Smart (Oxymitter 4000) Level 1 Sensing Probe Type 1 Ceramic diffusion element probe (ANSI) 3 Snubber diffusion element (ANSI) 4 Ceramic diffusion element probe (DIN) 6 Snubber diffusion element (DIN) 7 Ceramic diffusion element probe (JIS) 9 Snubber diffusion element (JIS) Level 2 Level 3 Level 4 Probe Assembly 0 18 (457mm) probe 1 18 (457mm) probe with abrasive shield 2 3 (0.91m) probe 3 3 (0.91m) probe with abrasive shield 4 6 (1.83m) probe 5 6 (1.83m) probe with abrasive shield 6 9 (2.74m) probe 7 9 (2.74m) probe with abrasive shield 8 12 (3.66m) probe 9 12 (3.66m) probe with abrasive shield A 15 (4.57m) probe with abrasive shield B 18 (5.49m) probe with abrasive shield Mounting Hardware (stack side) 0 No mounting hardware 1 New Installation square weld plate with studs 2 Mounting to Model 218 mounting plate (with Model 218 shield removed) 3 Mounting to existing Model 218 support shield 4 Mounting to other mounting 5 Mounting to Model 132 adapter plate Mounting Hardware (probe side) 0 No mounting hardware 1 Probe only (ANSI) 2 New bypass or new abrasive shield (ANSI) 4 Probe only (DIN) 5 New bypass or new abrasive shield (DIN) 7 Probe only (JIS) 8 New bypass or new abrasive shield (JIS) Level 5 Electronic Housing and Filtered Customer Termination NEMA 4X, IP For HART electronics integrally mounted to probe with transient protected filtered termination no cable required 14 For HART electronics mounted remotely with transient protected filtered termination must select cable below Level 6 Communications 1 Membrane keypad HART capable, blind cover 2 Membrane keypad HART capable, glass cover 3 Gas fluorescent LOI HART capable, glass cover, English only Page 11

12 ORDERING INFORMATION (continued) Level 7 Level 8 Level 9 Level 10 Language 1 English 2 German 3 French 4 Spanish 5 Italian Termination Filtering 00 Specified as part of electronic housing Calibration Accessories 00 No hardware 01 Cal./ref. flowmeter and ref. pressure regulator 02 Autocalibration Systems order by separate part number (for safe areas only) Electronics to Probe Cable 00 No cable integral electronics (6m) cable remote electronics (12m) cable remote electronics (18m) cable remote electronics (24m) cable remote electronics (30m) cable remote electronics (45m) cable remote electronics (61m) cable remote electronics Page 12

13 ORDERING INFORMATION General Purpose Oxymitter with FOUNDATION Fieldbus Communications. Optional Xi electronics not applicable. Model Description OXT5A In Situ Oxygen Transmitter with FOUNDATION fieldbus (Oxymitter 5000) Level 1 Sensing Probe Type 1 Ceramic diffusion element (ANSI) 3 Snubber diffusion element (ANSI) 4 Ceramic diffusion element (DIN) 6 Snubber diffusion element (DIN) 7 Ceramic diffusion element (JIS) 9 Snubber diffusion element (JIS) Level 2 Level 3 Level 4 Probe Assembly 0 18 (457mm) probe 1 18 (457mm) probe with abrasive shield 2 3 (0.91m) probe 3 3 (0.91m) probe with abrasive shield 4 6 (1.83m) probe 5 6 (1.83m) probe with abrasive shield 6 9 (2.74m) probe 7 9 (2.74m) probe with abrasive shield 8 12 (3.66m) probe 9 12 (3.66m) probe with abrasive shield A 15 (4.57m) probe with abrasive shield B 18 (5.49m) probe with abrasive shield Mounting Hardware (stack side) 0 No adapter plate 1 New Installation square weld plate with studs 2 Mounting to Model 218 (with Model 218 shield removed) 3 Mounting to existing Model 218 support shield 4 Competitor s mount 5 Mounting to Model 132 adapter plate Mounting Hardware (probe side) 0 No mounting hardware in adapter plate 1 Probe only (ANSI) 2 New bypass or new abrasive shield (ANSI) 4 Probe only (DIN) 5 New bypass or new abrasive shield (DIN) 7 Probe only (JIS) 8 New probe or abrasive shield (JIS) Level 5 Electronic Housing NEMA 4X, IP Transient protected filtered termination, integrally mounted to probe 14 Transient protected filtered termination, mounted remotely requires cable Level 6 Level 7 Communications/Operator Interface 1 Membrane keypad fieldbus, blind cover 2 Membrane keypad fieldbus, glass cover 3 Gas fluorescent LOI, fieldbus, glass cover Language 1 English 2 German 3 French 4 Spanish 5 Italian Page 13

14 ORDERING INFORMATION (continued) Level 8 Level 9 Level 10 Level 11 Termination Filtering 00 No option specified as part of electronic housing Calibration Accessories 00 No hardware 01 Cal. gas, flow rotometer and reference gas set 02 Autocalibration Systems order by separate part number (for safe areas only) Control Suite Functionality 00 Basic control suite 01 Deduct basic control suite Electronics to Probe Cable 00 No cable integral electronics ft. (6m) cable remote electronics ft. (12m) cable remote electronics ft. (18m) cable remote electronics ft. (24m) cable remote electronics ft. (30m) cable remote electronics ft. (45m) cable remote electronics ft. (61m) cable remote electronics Page 14

15 ORDERING INFORMATION Direct Replacement Oxymitter Probe replaces all older Westinghouse and Rosemount Analytical probes, as well as most competitive probes. Operates on most existing electronics, and also on the Xi enhanced interface electronics. Model OXT4ADR Description In Situ Oxygen Transmitter for use with existing electronics or Xi electronics Level 1 Sensing Probe Type 1 Ceramic diffusion element probe (ANSI) 3 Snubber diffusion element (ANSI) 4 Ceramic diffusion element probe (DIN) 6 Snubber diffusion element (DIN) 7 Ceramic diffusion element probe (JIS) 9 Snubber diffusion element (JIS) Level 2 Probe Assembly 0 18 (457mm) Probe 1 18 (457mm) Probe with abrasive shield 2 3 (0.91m) Probe 3 3 (0.91m) Probe with abrasive shield (1.83m) Probe 5 6 (1.83m) Probe with abrasive shield (2.74m) Probe 7 9 (2.74m) Probe with abrasive shield (3.66m)Probe (3.66m) Probe with abrasive shield 4 A 15 (4.57m) Probe with abrasive shield B 18 (5.49m) Probe with abrasive shield Level 3 Mounting Adapter Stack Side 2 0 No adapter plate 1 Mounting to stack (new installation) 2 Mounting to model 218/225/240 mounting plate (with probe support tube removed) 3 Mounting into existing model 218/225/240 probe support tube or bypass 4 Mounting into competitor s mounting 3 5 Model 132 / World Class 3000 adapter plate Level 4 Mounting Adapter Probe Side 0 No mounting hardware 1 Mounting probe only (ANSI) 2 Mounting probe with abrasive shield (ANSI) 4 Mounting probe only (DIN) 5 Mounting probe with abrasive shield (DIN) 7 Mounting probe only (JIS) 8 Mounting probe with abrasive shield (JIS) Level 5 Termination Unit 11 Standard filtered termination 12 Transient protected filtered termination Level 6 Arrangement-Existing Electronics 03 No hardware. For use with 218 analog electronics, world-class IFT electronics or Oxymitter electronics, Xi electronics 04 Westinghouse/Rosemount digital (218A) or universal electronics 05 VeriTrim electronics 07 Model 132 digital electronics 08 For use with Yokogawa electronics (cold junction comp. in probe junction box) 09 For use with other competitive oxygen analyzer systems Note: Order manual calibration accessories separately 263C152G01 Reference air regulator set 771B635H01 (2 required) flowmeters for calibration and reference air Page 15

16 Option Notes for Oxt4A, Oxt5A and Oxt4ADR Notes: In-Situ Oxygen Transmitter HART Smart High Sulfur Service: High sulfur cell can be selected for any probe; add a line item note to your purchase order requesting the high sulfur ZrO2 cell in place of the standard ZrO2 cell. Add 4232 UOM to the system matrix UOM total. Example: Note: Delete standard cell P/N 4847B63G01 Add high sulfur cell P/N 4847B63G02 Cell replacement kits for high sulfur service are also available. Consult P/N 4849B94XX in the Combustion Solutions Center Spare Parts list. Level 2: Option: 0 25/55 kgs/lbs shipping weight Level 2: Option: 2 27/60 kgs/lbs shipping weight Level 2: Option: 4 30/66 kgs/lbs shipping weight Level 2: Option: 6 33/72 kgs/lbs shipping weight Level 2: Option: 8 35/78 kgs/lbs shipping weight Level 2: Option: 3 45/100 kgs/lbs shipping weight Level 2: Option: 5 50/110 kgs/lbs shipping weight Level 2: Option: 1, 7 54/120 kgs/lbs shipping weight Level 2: Option: 9 60/130 kgs/lbs shipping weight Level 2: Option: A 66/145 kgs/lbs shipping weight Level 2: Option: B 72/158 kgs/lbs shipping weight Level 2: Option: 1, 3, 5, 7, 9, A, B Recommended usages: high velocity particulates in flue stream, installation within 10 (3.5 m) of soot blowers or heavy salt cake build up. Applications: pulverized coal, recovery boilers, lime kiln. Regardless of application, abrasive shields with support brackets are recommended for 9 (2.74 m) and 12 (3.66 m), 16 (4.57 m) and 18 (5.49 M) probe installations, particularly horizontal installations. Level 3: Option: 4 Where possible, specify SPS number, otherwise provide details of the existing mounting plate as follows: Plate with studs: Bolt circle diameter, number and arrangements of studs, stud thread, stud height above mounting plate. Plate without studs: Bolt circle diameter, number and arrangement of holes, thread, depth of stud mounting plate with accessories. Level 6: Option: 1 Startup, calibration and operation can be implemented using the standard membrane keypad. Remote access and additional functionality available via HART /FOUNDATION Field Communications (Model 375 Hand-held Communicator or AMS) with Oxymitter device descriptor (DD) required. ORDERING INFORMATION AUTOCALIBRATION ACCESSORIES Model XSO2CAL Level 1 Level 2 Description O 2 Autocalibration Accessories - apply to Oxymitter or Xi electronics. General purpose only. Single Probe Sequencers Autocalibration options 00 None 01 SPS 4001 Single Probe Sequencer, general purpose NEMA 4X, includes check valve for probe Intelligent Multiprobe Sequencers (IMPS) 00 None 01 IMPS Intelligent Probe Sequencer, single-probe, general purpose NEMX 4X, includes valve for probe 02 IMPS Intelligent Probe Sequencer, two-probe, general purpose NEMX 4X, includes valve for probe 03 IMPS Intelligent Probe Sequencer, three-probe, general purpose NEMX 4X, includes valve for probe 04 IMPS Intelligent Probe Sequencer, four-probe, general purpose NEMX 4X, includes valve for probe 05 IMPS Intelligent Probe Sequencer, single-probe, 115V heated general purpose NEMX 4X, includes valve for probe 06 IMPS Intelligent Probe Sequencer, two-probe, 115V heated general purpose NEMX 4X, includes valve for probe 07 IMPS Intelligent Probe Sequencer, three-probe, 115V heated general purpose NEMX 4X, includes valve for probe 08 IMPS Intelligent Probe Sequencer, four-probe, 115V heated general purpose NEMX 4X, includes valve for probe 09 IMPS Intelligent Probe Sequencer, single-probe, 220V heated general purpose NEMX 4X, includes valve for probe 010 IMPS Intelligent Probe Sequencer, two-probe, 220V heated general purpose NEMX 4X, includes valve for probe 011 IMPS Intelligent Probe Sequencer, three-probe, 220V heated general purpose NEMX 4X, includes valve for probe 012 IMPS Intelligent Probe Sequencer, four-probe, 220V heated general purpose NEMX 4X, includes valve for probe Page 16

17 ORDERING INFORMATION OPTIONAL Xi ADVANCED ELECTRONICS Model XI Level 1 Level 2 Level 3 Description O 2 Advanced electronics Xi Type 01 Future 02 Future 03 Future 04 Traditional Architecture Xi - all signal conditioning and operator interface via the Xi. Cable required, single channel only. 05 Traditional Architecture Xi - all signal conditioning and operator interface via the Xi. Cable required, single channel only, set up to run 44V world class probe Calibration & Reference Gas Accessories 00 No Hardware 01 Calibration & Reference Gas Flowmeters & Reference Regulator/Filter Cable (For Traditional Architecture Xi Only) 00 None (6m) Cable (12m) Cable (18m) Cable (24m) Cable (30m) Cable (45m) Cable (60m) Cable Level 4 Stoichiometer Function 00 No 01 Single Channel 02 Dual Channel Level 5 Programmable Reference Function 00 No 01 Single Channel 02 Dual Channel Level Deg C Process Function 00 No 01 Single Channel 02 Dual Channel NOTES: Order Direct Replacement Oxymitter probe separately - Oxt4ADR Page 17

18 Xi Enhanced Interface - Panel Mounting Details Xi Enhanced Interface - Wall/Surface and Pipe Mounting Details Page 18

19 OXYMITTER ACCESSORIES HART Hand-held 375 Communicator The FOUNDATION fieldbus 375 Communicator is an interface device that provides a common communication link to HART /FOUNDATION fieldbus compatible instruments, such as the Sulfur-Resistant Oxymitter. HART Communications Protocol permits all the information available from the Sulfur-Resistant Oxymitter electronics to be transmitted over standard 4-20 ma signal wires or FOUNDATION fieldbus wires. By attaching the hand-held communicator at a termination point along the signal line, a technician can diagnose problems and configure and calibrate the Sulfur-Resistant Oxymitter as if he or she were standing in front of the instrument. For more information, call Rosemount Analytical at Bypass Packages The specially designed Rosemount Analytical Bypass Package for oxygen analyzers has proven to withstand the high temperatures in process heaters while providing the same advantages offered by the in situ sensor. Inconel tubes provide effective resistance to corrosion, and the other components common to other sampling systems. For more information, call Rosemount Analytical at O 2 Calibration Gas Kits - pn. 6296A27G01 Rosemount Analytical s O 2 Calibration Gas and Service Kits have been carefully designed to provide a more convenient and fully portable means of testing, calibrating, and servicing Rosemount Analytical s oxygen analyzers. These lightweight, disposable gas cylinders eliminate the need to rent gas bottles. For more information, call Rosemount Analytical at Wireless THUM TM Adaptor The Smart Wireless THUM Adaptor converts the standard 4-20mA signal from the Xi electronics to a wireless signal. All HART information is transmitted in addition to the process O 2 value. For more information, call Rosemount Analytical at Page 19

20 SPECIAL ARRANGEMENTS Special Cells for High Acid Service Many combustion processes use fuels that contain sulfur of HCI. Special cells provide extended life in these difficult applications. Catalyst Regeneration Measure O 2 in regenerators at pressures up to 50 psi. In situ design resists plugging due to catalyst fines Class I, Div. I, Group B, C and D. Optional pressure balancing arrangement. Optional isolation valving system permits installation and withdrawal while the process is running. Specified by UOP. See Application Data Sheet ADS F.A01. Isolation Valving System O 2 Probe in Retracted Position Integral Pressure Balancing Assembly Pressure balanced in situ O 2 probe with optional isolation valving system (probe withdrawn) The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by our terms and conditions, which are available on request. We reserve the right to modify or improve the designs or specifications of our products at any time without notice. To find the local Rosemount Analytical specialist near you, go to: 8 Rosemount Analytical Inc., All rights reserved. Printed in U.S.A. on recycled paper.