LoveHorsepower's MR2 Turbo Fuel Pressure Regulator Kit

Transcription

1 LoveHorsepower's MR2 Turbo Fuel Pressure Regulator Kit 1 / 20

2 Update - This kit is no longer for sale, but you can purchase nearly all of parts from Summi t Racing. You will need: Part Number Number of Item Part AEI Fuel Pressure Regulator EAR ERL 90-6 Male to Male Swivel 12mm SUM Vacuum Line 1/8" 6 SUM Gauge Fuel Press Liquid Fill100 AER-FBM1512 Fitting 6AN -To-Barb Straght You will also need a reducing couple that can be purchased from McMaster Carr - part number is 56 7K13. You may also wish to order fuel hose from Summit Racing - part number is GTR-65128, or you can pick up a shorter (and perhaps cheaper) hose segment at your local auto parts store. The hose clamps can be purchased from your local hardware store such as Lowes or Home Depot. LoveHorsepower Fuel Pressure Regulator Kit Installation Video - Full Resolution 115MB windows media format. Right click and save as to view. Fuel Pressure Regulator Video Tuning Guide Video - Full Resolution - 92MB windows media format. Right click and save as to view. 2 / 20

3 Some of pictures and notes from video are presented here, but please see video for installation instructions and tuning guide. Also please see fuel injectors removal instructions as process is very similar since fuel rail must be removed. Here is strut tower brace - remove two 14mm bolts and two 14mm nuts. 3 / 20

4 Remove four 12mm bolts holding on throttle body inlet. Remove two 10mm bolts and two 12mm bolts holding on throttle body bracket. 4 / 20

5 Remove four 12mm bolts holding on throttle body. 5 / 20

6 Then to leak remove out, move and replace coolant throttlethat lines, body coolant it's outnot ofwhen a big way installation deal, without just be is removing complete. prepared forcoolant a smalllines. amount If you of would coolantlike to 6 / 20

7 Remove 12mm bolt supporting EGR assembly, and disconnect EGR electrical connection. 7 / 20

8 Remove right of picture. two 12mm bolts holding EGR assembly to intake manifold. See arrows on 8 / 20

9 Remove be removed. Allen bolts holding EGR assembly onto head. The EGR assembly can now 9 / 20

10 Remove two 12mm bolts holding on cold start injector pipe. There are two washers per bolt. 10 / 20

11 After 10mm bolts. cold start injector is removed, unbolt wiring harness from intake manifold - two 11 / 20

12 Unbolt way, and three n bolts lift out holding fuel rail. fuel rail in place. Pull on wiring harness to move it out of 12 / 20

13 Remove 10mm bold holding fuel inlet pipe in place, n remove stock fuel pressure regulator. 13 / 20

14 Stock regulator removed: 14 / 20

15 Install 90 degree fitting into fuel rail where stock regulator once was. 15 / 20

16 Connect tape on this oneconnection. of three barbed fittings included in kit. There is no reason to use any teflon 16 / 20

17 Attach fuel hose and hose clamp. 17 / 20

18 Assemblein included Aeromotive LoveHorsepower fuel pressure kit. regulator with fittings and fuel pressure gauge 18 / 20

19 Drillhave regulator adjusting still attach (blue) two do mounting clearance will not screw fuelclear require return onholes top toany line. close hood ofinsealant. Please when regulator firewall hood. use closed. teflon Use at - ie an Check make appropriate tape fittings sure that on you that and gold location. have when hose colored clearance clamps Be screw sure fittings. included that toisloosen All full or loosened, with top of fittings kityou to Regulator Kit Installed! 19 / 20

20 Only Please adjust see installation base fuel pressure and tuning with videos! vacuum line orthrough with engine off. LoveHorsepower Fuel Pressure Regulator Kit 115MB windows media format. Right and save as todisconnected view. - Full -MR2 Fuel Pressure Regulator Video Tuning Video media format. Right click and save asclick toguide view. - we FullVideo Resolution -Resolution 92MB Check out a more detailed tuning page with Lovehorspower regulator kit, AFC, on and Installation exact boost. process went to tunewindows 20 / 20