Nissan R35 GTR Intercooler Pipe Kit w/ Cold Air Intake Installation Instructions

Size: px
Start display at page:

Download "Nissan R35 GTR Intercooler Pipe Kit w/ Cold Air Intake Installation Instructions"

Transcription

1 Nissan R35 GTR Intercooler Pipe Kit w/ Cold Air Intake Installation Instructions 1. Disconnect the negative terminal on the battery that is located at the passenger firewall side. 2. Remove both front driver and passenger side front wheels.

2 3. Remove all 12 plastic clips and 1 Phillip head screw on top side of fender wheel well. 4. (Optional) Remove the driver side wheel well splash guard fender. 5. Repeat step 3 and 4 to remove the passenger side wheel well splash guard fender.

3 6. Remove the front under side air splitter by removing all 14 x 10mm, 2 x 12mm bolts, and 2 plastic clips. 7. Remove the fender s Side Marker Lights by pushing in the clip. Disconnect the electrical connector. Repeat the same procedure on the other side of the car. Optional: Using some masking tape and tape off the fender and bumper line section to prevent any scratching when removing the front bumper

4 8. Remove 3 x 10mm screws on the underside of the driver and passenger side front wheel fenders 9. Remove the hood latch cover by removing all 8 plastic clips. 10. Remove all 6 upper front bumper plastic clips

5 11. (Optional) For clearance to access the turbo to IC pipe Remove all 8 x 10mm bolts and remove the front underside Air Splitter Center Skid Plate. 12. Remove the plastic clip on OEM air box inlet on driver side, and then remove the inlet. Repeat same procedure on passenger side. 13. Optional: For ease of removing front bumper (preserving the paint) and installing pipe kits, it is recommended to have a 2 nd installer present for assistance.

6 14. Remove the OE front fascia/bumper. 15. Remove the passenger side OEM oil cooler air duct by removing 4 plastic clips. 16. Remove the passenger side OEM oil cooler air duct bracket by removing 4 x 10mm bolts.

7 17. Remove the passenger side OEM oil cooler by removing the 4 x 10mm bolts. DO NOT DISCONNECT the oil lines from the cooler. 18. Disconnect the recirculation hose and vacuum source hose from OEM BPV on both driver and passenger side. 19. Remove two 12mm bolts that attach the OEM BPV on both driver and passenger side.

8 20. Loosen both hose clamps on the coupler that are connecting the air-box to turbo inlet. Then remove the 10mm bolt on side of air box. Repeat same procedures on the other side. 21. Remove wire harness bracket on both driver and passenger side by removing the 12 mm bolt. 22. Remove air boxes on both driver and passenger side.

9 23. Remove the driver side air temperature sensor and its harness on the OE Throttle body pipe. 24. Loosen all the driver side OE clamps from TB to IC with an 8mm ratchet or flat head screw driver.

10 25. Remove the driver side OE BPV recirculation hose from the BPV to Turbo. 26. Remove 3 x 12mm bolts for the center piece of OE IC to TB pipe under the driver side fender wheel well.

11 27. Remove driver side all 3 pieces (2 x metal, 1 x rubber pipes) of the IC to TB OE pipes 28. Remove the driver side Turbo to IC connector pipe by removing the 12mm bolt, wire harness anchor, x 8mm clamps holding the rubber coupler to the IC. Then repeat step 23 to 28 on the passenger side of the car.

12 30. Install the removable inserts into the intake pipes. 31. Remove both MAF sensors from OEM air boxes and reinstall both sensors on to Synapse Engineering intake pipes. Reuse the 7mm bolts to fasten the sensors on the intake pipes. 32. Install the 45 degree silicone couplers and clamps on both driver and passenger side, but do not tighten the clamps yet.

13 33. Install the passenger side intake pipe onto silicone coupler that is already on the turbo inlet. 34. For driver side intake pipe, remove driver side power steering reservoir lower bolt, then line up the driver side intake bracket bolt hole to the same hole. Fasten the 10mm bolt onto the bracket but do not tighten yet. 35. Install air filter onto intake pipe on both driver and passenger side, but do not tighten filter clamp yet. Then adjust the intakes and filters assembly to allow proper clearance in order to prevent the intake assemblies physically contacting their surroundings.

14 36. Tighten all components for the GTR intake assembly on both driver and passenger sides. 37. Install a 2.75 straight coupler onto the passenger side throttle body, and then install the KIT (Pass. Upper IC to TB Pipe). Place the Gap Spacer (provided) between the pipe bracket and the strut tower bolt hole, then fasten the 10mm bolt (provided). 38. Install a 2.75 to 2.5 Reducer coupler onto the passenger side Intercooler outlet side.

15 39. Install a 2.75 straight coupler onto the KIT pipe, and then install KIT (Pass. Lower IC to TB Pipe). Connect the other end of the pipe to the coupler from the previous step. Line up the pipe bracket to the proper bolt hole as indicated in the above (right side) picture. Note: Notice that the Passenger side IC to TB Lower Pipe has a slight bend on the Upper Pipe connecting side. 40. Preinstall a 2.25 to 2 Reducer Coupler onto the turbo discharge. Preinstall a 2.75 to 2.25 Reducer Coupler onto the Intercooler inlet side.

16 41. Install the KIT (Pass Side Turbo to IC Pipe) according to the steps as depicted in the above 3 pictures. Repeat steps 36 to 40 for the driver s side Intercooler Pipe kit install. 42. Place the adapter O-ring on the inlet side of the BOV. Make sure the O-ring sits flat in the BOV before installing onto the pipe.

17 43. Install the Synchronic Blow-Off-Valves onto the IC to TB Upper Pipes on both driver and passenger side. Then install the BOV Discharge Recirculation Pipes onto the recirculation inlet (circled in the above picture) on the turbo. Use the 1.25 couplers & clamps provided. Cut and re-size the 1.25 couplers if necessary.

18 44. Measure about 7 inches in length of Boost Connect hose and cut 2 equal length pieces. Connect the 2 pieces of hose to Y connector. Then Cut approximately 5 inches of Boost Connect hose and push that into the collector side of the Y connector. 45. Push the other end of the cut Boost Connect hose into the OEM vacuum hose that was connected to the OEM By-Pass-Valve. Try to push it approximately 2 inches into the OEM vacuum hose. Then slide the OE hose clamp back to ensure tight fit. 46. Connect the MAF sensors to driver and passenger side s Intake Pipes

19 47. Install and connect the pressure sensors to the undersides of driver and passenger IC to Throttle Body Pipes. 48. Check all pipe kit components and ensure all bolts and clamps are tighten. 49. Reinstall the passenger side oil cooler assembly and check that the oil lines are still connected and have not sustained any damages throughout the installation process.

20 50. Reinstall the OE front fascia/bumper and driver/passenger side markers. 51. Reinstall the Air Splitter Center Skit Plate if it was previously removed. 52. Reinstall the OE Front Air Splitter.

21 53. Reinstall the OE Hood Latch Cover 54. Reinstall driver and passenger sides wheel well splash guard fenders if they were removed. Driver & Passenger side Install Complete

Mitsubishi Evolution X Intercooler Pipe Kit Installation Instructions

Mitsubishi Evolution X Intercooler Pipe Kit Installation Instructions Mitsubishi Evolution X Intercooler Pipe Kit Installation Instructions Disclamer: This product is intented for off road use only. Driving on public roads and highways with this product installed on vehicle

More information

7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions

7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions 7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following

More information

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) 1 2 Remove two bolts in trunk cover with 8mm socket. Pull up on cover to remove. Unscrew net tie down on side cover where battery is located

More information

MAZDASPEED3 Intercooler Instructions

MAZDASPEED3 Intercooler Instructions MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through

More information

Installation Manual. Model Chassis Code Engine Code Year

Installation Manual. Model Chassis Code Engine Code Year INTERCOOLER KIT NISSAN GT-R R35 (VR38 38DETT) SPEC-R HG TYPE29 Full KIT Installation Manual Please read the Installation Manual before installing. Keep this manual for future reference. Model Chassis Code

More information

Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI

Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following

More information

Installation Manual. Model Chassis Code Engine Code Year

Installation Manual. Model Chassis Code Engine Code Year INTERCOOLER KIT NISSAN GT-R R35 (VR38 38DETT) SPEC-R HG TYPE29 Full KIT Installation Manual Please read the Installation Manual before installing. Keep this manual for future reference. Model Chassis Code

More information

Wrenches: ⅞, 8mm, 10mm, 13mm, 19mm P. allen, Other: Electrical Tape

Wrenches: ⅞, 8mm, 10mm, 13mm, 19mm P. allen, Other: Electrical Tape IAG Street Series Air / Oil Separator (AOS) For 2008-14 STI Part# IAG-ENG-7100 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15)

Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) Huron Speed Products Twin Turbo Install Gen 2 CTS-V (09-15) The following install guide is simply that, a guide to help you with installation. It is by no means the exact method to perform installation,

More information

05-08 GT. Hellion Power Systems Mustang Kit Instructions

05-08 GT. Hellion Power Systems Mustang Kit Instructions Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo

More information

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7100 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat

More information

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat

More information

8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles)

8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles) P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

IAG Competition Series Air / Oil Separator (AOS) For 2017 STI

IAG Competition Series Air / Oil Separator (AOS) For 2017 STI P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI

IAG Street Series Air / Oil Separator (AOS) For WRX & WRX STI IAG Street Series Air / Oil Separator (AOS) For 2006-07 WRX & 2004-07 WRX STI Part# IAG-ENG-7150 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat

More information

IAG Street Series Air / Oil Separator (AOS) For WRX

IAG Street Series Air / Oil Separator (AOS) For WRX P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

IAG Competition Series Air / Oil Separator (AOS) For WRX

IAG Competition Series Air / Oil Separator (AOS) For WRX P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw

More information

2015+ EcoBoost F150 & Raptor Intercooler Install

2015+ EcoBoost F150 & Raptor Intercooler Install 2015+ EcoBoost F150 & 2017+ Raptor Intercooler Install Note: This entire job can be performed with the truck on the ground - No need to raise the vehicle. The most difficult part is removing the grille

More information

Procharger Stage II Intercooled Supercharger System (11-14 GT)

Procharger Stage II Intercooled Supercharger System (11-14 GT) Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2

More information

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side 2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and

More information

Parts List See cover Page

Parts List See cover Page Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let

More information

FRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # & P INSTALATION INSTRUCTIONS

FRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # & P INSTALATION INSTRUCTIONS FRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # 48.10.90 & 48.10.90P INSTALATION INSTRUCTIONS PART LIST: 1 INTERCOOLER CORE 1 U-BENT TUBE 1 L-SHAPED TUBE 1 INTERCOOLER INLET TUBE 4 M6 NYLOC NUT 3 M6

More information

Instant Chat off the main page of Or simply call our tech team at

Instant Chat off the main page of   Or simply call our tech team at FRONT MOUNT INTERCOOLER 2008-13 STI 2014-04- 08 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation

More information

IAG Street Series Air / Oil Separator (AOS) For WRX

IAG Street Series Air / Oil Separator (AOS) For WRX IAG Street Series Air / Oil Separator (AOS) For 2008-14 WRX Part# IAG-ENG-7100 Tools Required: Ratchet, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver, hose clamping

More information

Part number SP Mitsubishi Evo VIII, MR,IX 2.0L 4 cyl.

Part number SP Mitsubishi Evo VIII, MR,IX 2.0L 4 cyl. Part number SP1898 2003-06 Mitsubishi Evo VIII, MR,IX 2.0L 4 cyl. 1- Dyno-proven aluminum cast intake 1- Three piece intercooler pipes A (T/B), B (intercooler) C (turbo) 1-4 1/2 Injen filter (#1018) 1-1890

More information

IAG Street Series Air / Oil Separator (AOS) For 2017 WRX

IAG Street Series Air / Oil Separator (AOS) For 2017 WRX P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,

More information

2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED

2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE

More information

Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide

Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide Congratulations on your new upgraded piping and intercooler kit, this kit has proven to provide the lowest intake air temps to date on our

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-486 2003-2003.5 MazdaSpeed Protégé 2.0L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

Difficulty Level: 3-4. This is very intensive for an intercooler installation. Experienced mechanical skills recommended. Wrenches Sockets Specialty

Difficulty Level: 3-4. This is very intensive for an intercooler installation. Experienced mechanical skills recommended. Wrenches Sockets Specialty Nissan GT-R FMIC The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs AMS will never compromise the

More information

R8 Exhaust Installation Guidelines

R8 Exhaust Installation Guidelines STāSIS Engineering R8 Exhaust Installation Guidelines Exhaust Muffler support bracket bolt to muffler Muffler support bracket to chassis Muffler heat shield screws Heat shield bolt to chassis beneath anti

More information

How to: Install a Ford EcoBoost F150 Intercooler

How to: Install a Ford EcoBoost F150 Intercooler How to: Install a 2015+ Ford EcoBoost F150 Intercooler This article documents the installation of our Full-Race 2015+ F150 Ecoboost Intercooler / CAC Upgrade Kit. The addition of a high performance air-to-air

More information

IAG Air / Oil Separator (AOS) For STi

IAG Air / Oil Separator (AOS) For STi IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,

More information

INTERCOOLER PIPE KIT CHEVY CAMARO 2.0T PARTS LIST AND INSTALLATION GUIDE PARTS INCLUDED CAUTION INSTALL PROCEDURE TOOLS NEEDED

INTERCOOLER PIPE KIT CHEVY CAMARO 2.0T PARTS LIST AND INSTALLATION GUIDE PARTS INCLUDED CAUTION INSTALL PROCEDURE TOOLS NEEDED PARTS LIST AND PARTS INCLUDED 2PC ALUMINUM PIPES W/ CNC-MACHINED QUICK-DISCONNECTS 1PC ALUMINUM PIPE W/ CNC-MACHINED 2-BOLT FLANGE 2PC QUICK-DISCONNECT SPRING CLIPS 1PC 2.75" 90 SILICONE COUPLER 1PC 2.25"

More information

Installation Instructions Camaro ZL1 ( Z) ( ZB)

Installation Instructions Camaro ZL1 ( Z) ( ZB) Installation Instructions Camaro ZL1 (501-1099-10-Z) (501-1099-10-ZB) Parts List 1 Insulated Air Box \ Lid 1 Thermal Coated Intake Tube / MAF Housing with (2) M4 x.7 thread 8mm long Stainless Screws; 1

More information

Always wear safety glasses when working on your vehicle.

Always wear safety glasses when working on your vehicle. 90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively

More information

INSTALLATION INSTRUCTIONS. PART NUMBER C (Gun Metal Gray Finish) 2016 HYUNDAI TUCSON 1.6 Turbo

INSTALLATION INSTRUCTIONS. PART NUMBER C (Gun Metal Gray Finish) 2016 HYUNDAI TUCSON 1.6 Turbo INSTALLATION INSTRUCTIONS PART NUMBER 26-3002C (Gun Metal Gray Finish) 2016 HYUNDAI TUCSON 1.6 Turbo 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 08483K HOSE CLAMP #28, BLACK ZINC PLATED 2 2 5-1070 COUPLER;1.75-2.50X3.25"

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Nissan 350Z

COLD AIR SYSTEM. Installation Instructions for: Part Number Nissan 350Z COLD AIR SYSTEM Installation Instructions for: Part Number 21-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

Application List L Cummins

Application List L Cummins 1 Discharging & Recharging of the A/C System is required for this install. INTERCOOLER INSTALLATION FOR 2010+ DODGE 6.7L CUMMINS Application List 2010+ 6.7L Cummins 1042530 PLEASE READ ALL INSTRUCTIONS

More information

Installation Instructions :BMW B58 : Page 1

Installation Instructions :BMW B58 : Page 1 Installation Instructions :BMW B58 : Page 1 1. We will start by removing the stock airbox system. Loosen the hose clamp around the airbox. Remove the MAF sensor plug the white clip unlocks by pulling it

More information

3/8 Universal Joint Phillips Head Screwdriver

3/8 Universal Joint Phillips Head Screwdriver Magnetic retrieval tool Pliers 1/4 Ratchet Drive T-35 Torx Socket 3/8 Ratchet Drive 5mm Allen Head Socket Torque Wrench 7-3/8 Drive Extension Flat Head Screwdriver 10mm Socket 8mm Socket 3/8 Universal

More information

Banks High-Flow Boost Tubes. Step-by-step installation video: Bankspower.com/v/install-lml-boost-tubes

Banks High-Flow Boost Tubes. Step-by-step installation video: Bankspower.com/v/install-lml-boost-tubes with Installation Instructions Owner smanual Banks High-Flow Boost Tubes Stock Fitment 2011-2016 Chevy/GMC Turbo-Diesel Pickup Trucks THIS MANUAL IS FOR USE WITH PART NUMBER 25993 Gale Banks Engineering

More information

Bill of Materials for

Bill of Materials for Bill of Materials for 77060012 1 2-P5153572 Inlet Pipe 1 21-202M 2.75" Filter 1 103-BLO-4820N Filter Hose Clamp 1 559999 Washer, Fender M6x25 1 1-3028 Washer, 1/4 SAE Flat 1 1-2072 Bolt, 1/4-20-UNC x 1

More information

V1 Truck Manifold Turbo Kit for F-body

V1 Truck Manifold Turbo Kit for F-body V1 Truck Manifold Turbo Kit for 98-02 F-body Prep: -Remove all A/C Components, Alternator and brackets, tensioner, front bumper, front bumper foam, and front bumper support. Remove radiator and cooling

More information

INSTRUCTION. INTERCOOLER UPGRADE BMW E92 335i

INSTRUCTION. INTERCOOLER UPGRADE BMW E92 335i INSTRUCTION INTERCOOLER UPGRADE BMW E92 335i 2007-2011 Parts Included: - Intercooler - Shroud with seals - Left and right side pipes with hoses - 1 Silicone Hoses ( 2.5 x 3 ) - 2 Silicone Hose 45 degree

More information

JBR MAZDASPEED

JBR MAZDASPEED Page1 james Barone Racing Aftermarket Parts and Accessories JBR 2007 2009 MAZDASPEED 3 Front Mount Intercooler Piping Kit Installation Instructions for TR8 Intercooler Tooling: o Jack, Jack Stands, Ramps

More information

INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT

INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT 2015+ SUBARU WRX (LHD ONLY) Document: 19-0136 Support: info@radiumauto.com This document covers the installation of the Radium brake master cylinder brace

More information

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS

CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic

More information

Instant Chat off the main page of Or simply call our tech team at

Instant Chat off the main page of   Or simply call our tech team at FRONT MOUNT INTERCOOLER 2015+ WRX 2017-07-07 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of

More information

TOYOTA FJ CRUISER / 4RUNNER COLD AIR INTAKE Section I Installation Preparation. 4.0L V6 (1GR) Roller Rocker Part Number(s): PTR

TOYOTA FJ CRUISER / 4RUNNER COLD AIR INTAKE Section I Installation Preparation. 4.0L V6 (1GR) Roller Rocker Part Number(s): PTR Section I Installation Preparation Part Number(s): PTR03-89100 Kit Contents Item # Quantity Reqd. Description 1 1 Air Filter (P/N: PTR43-00083) 2 1 Upper Air Box 3 1 Lower Air Box 4 1 Hump Coupler 5 1

More information

SHORT RAM AIR INTAKE SYSTEM. Installation Instructions for: Part Number Nissan 350Z

SHORT RAM AIR INTAKE SYSTEM. Installation Instructions for: Part Number Nissan 350Z SHORT RAM AIR INTAKE SYSTEM Installation Instructions for: Part Number 22-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Infiniti G35

COLD AIR SYSTEM. Installation Instructions for: Part Number Infiniti G35 COLD AIR SYSTEM Installation Instructions for: Part Number 21-548 2003-2005 Infiniti G35 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

INSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM

INSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting

More information

2015 Corvette Supercharger System Instructions

2015 Corvette Supercharger System Instructions 2015 Corvette Supercharger System Instructions These instructions are meant to serve as a guide to the installation of the ECS 2015 Corvette Supercharging system. Please be sure to use all safety equipment

More information

Alpha Intercooler Install Instructions w/stock turbo

Alpha Intercooler Install Instructions w/stock turbo Alpha 997.1 Intercooler Install Instructions w/stock turbo The goal of Alpha Performance is to provide the highest quality, best performing products available. By utilizing research and development, and

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number Mitsubishi Lancer Ralliart Manual Transmission Only

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number Mitsubishi Lancer Ralliart Manual Transmission Only COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-436 2004-2005 Mitsubishi Lancer Ralliart Manual Transmission Only ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne,

More information

Instruction P/N:EVO1800

Instruction P/N:EVO1800 Q R S Instruction D EXPLODED VIEW A WARNING: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PRO- VIDED HARDWARE MAY DAMAGE THE INTAKE SYSTEM, ENGINE AND COMPONENTS!!! *Do not attempt to

More information

INSTALLATION INSTRUCTIONS Dual Catch Can Kit Subaru Turbo and STi Document# Support:

INSTALLATION INSTRUCTIONS Dual Catch Can Kit Subaru Turbo and STi Document# Support: INSTALLATION INSTRUCTIONS Dual Catch Can Kit 02-14 Subaru Turbo and 2015+ STi Document# 19-0099 Support: info@radiumauto.com This document covers the installation of a Radium dual catch can kit for the

More information

Installation Instructions :BMW E39 M5 : Page 1

Installation Instructions :BMW E39 M5 : Page 1 Installation Instructions :BMW E39 M5 : Page 1 1. We will start by removing the front bumper. Remove the 3 x 8mm hex head bolts in the wheel arch liners on both sides. Turn the wheels to gain access. 2.

More information

7 th Gen. Celica GTS Turbo Kit Installation Guide This kit has not been CARB approved and is intended for racing / offroad purposes only.

7 th Gen. Celica GTS Turbo Kit Installation Guide This kit has not been CARB approved and is intended for racing / offroad purposes only. 7 th Gen. Celica GTS Turbo Kit Installation Guide This kit has not been CARB approved and is intended for racing / offroad purposes only. The purpose of this guide is to serve as a reference for use when

More information

Part number SP Mitsubishi Evo VIII, MR,IX 2.0L 4 cyl.

Part number SP Mitsubishi Evo VIII, MR,IX 2.0L 4 cyl. Part number SP1898 2003-06 Mitsubishi Evo VIII, MR,IX 2.0L 4 cyl. 1- Dyno-proven aluminum cast intake 1- Three piece intercooler pipes A (T/B), B (intercooler) C (turbo) 1-4 1/2 Injen filter (#1018) 1-1890

More information

---Optional Items---

---Optional Items--- 1 2 3 4 5 6 ---Optional Items--- 10 9 11 7 8 12 This package should contain: 1. One (1) CorkSport Crashbar Weldment 2. Eight (8) M8x1.25x20 mm Bolts 3. Eight (8) M8x1.25mm Nyloc Nuts 4. Sixteen (16) M8

More information

Tools Required. Metric Wrench Set Screwdriver Set Metric Socket Set Pliers Heavy duty hydraulic Jack and Car Stands Box knife or similar Hacksaw WD40

Tools Required. Metric Wrench Set Screwdriver Set Metric Socket Set Pliers Heavy duty hydraulic Jack and Car Stands Box knife or similar Hacksaw WD40 Subaru 2004+ Legacy GT & Outback XT For JDM 2.0 twinscroll turbo and USDM 2.5 turbo models Front Mount Intercooler Fitting Instructions PN# LEG-1348-000 You are now the proud owner of a highly tested and

More information

CorkSport Mazdaspeed Protégé Intercooler Hoses Mazdaspeed Protégé

CorkSport Mazdaspeed Protégé Intercooler Hoses Mazdaspeed Protégé CorkSport Mazdaspeed Protégé Intercooler Hoses 2002-2003.5 Mazdaspeed Protégé Thank you for purchasing the CorkSport Mazdaspeed Protégé Intercooler Hose Kit. This kit has been designed and tested to be

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR

COLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR COLD AIR SYSTEM Installation Instructions for: Part Number 21-469 2003-2004 Toyota Corolla 2002-2004 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

Installation Instructions : Jaguar F-Type Intake System : Page 1

Installation Instructions : Jaguar F-Type Intake System : Page 1 Installation Instructions : Jaguar F-Type Intake System : Page 1 1. Remove the undertray all the Torx bolts and the hex bolts holding the splitters in place need to be removed. 2. Starting with the right

More information

Subaru WRX Performance Charge-Pipe System, 2015+

Subaru WRX Performance Charge-Pipe System, 2015+ PARTS LIST AND PARTS LIST 1PC BAR-AND-PLATE INTERCOOLER 1PC INTERCOOLER MOUNTING BRACKET 1PC CHARGE-PIPE ASSEMBLY 1PC AIR DIVERTER WITH ATTACHED RUBBER GASKETS 1PC CHARGE-PIPE-TO-INTERCOOLER HOSE INSTALLATION

More information

INSTALLATION INSTRUCTIONS PART NUMBER:21-729

INSTALLATION INSTRUCTIONS PART NUMBER:21-729 Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-729 2010-2013 MAZDA MX-5 MIATA 2.0L I-4 PARTS LIST Description Qty. Part Number A Tube, Lower Intake, 2006-13

More information

GrimmSpeed Install Guide Series Installing the GrimmSpeed WRX Boost Control Solenoid Updated 4/14/15

GrimmSpeed Install Guide Series Installing the GrimmSpeed WRX Boost Control Solenoid Updated 4/14/15 GrimmSpeed Install Guide Series Installing the GrimmSpeed 2015+ WRX Boost Control Solenoid Updated 4/14/15 Introduction: This guide will illustrate the installation of the GrimmSpeed 2015+ WRX Boost Control

More information

ZZPerformance.com ZZP 3 Redline Cold Air Intake GEN 2

ZZPerformance.com ZZP 3 Redline Cold Air Intake GEN 2 Tools you will need: Flat Blade Screwdriver Phillips Screwdriver 10mm End Wrench Ratchet Extension 5.5mm Socket 7mm Socket 10mm Socket 13mm Deep Socket ZZPerformance.com ZZP 3 Redline Cold Air Intake GEN

More information

INSTALLATION INSTRUCTIONS 3 BULL BAR W-BUILT IN LED LIGHT TOYOTA TACOMA

INSTALLATION INSTRUCTIONS 3 BULL BAR W-BUILT IN LED LIGHT TOYOTA TACOMA INSTALLATION INSTRUCTIONS PARTS LIST: 1 3 Bull Bar 4 12mm Hex Nuts 1 Driver/Left Frame Mounting Bracket 2 10-1.50mm x 120mm x 30mm Hex Bolts 1 Passenger/Right Frame Mounting Bracket 2 10mm x 30mm OD x

More information

96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions

96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions 96-04 tt Hellion Power Systems 1996-2004 Mustang Twin Turbo Kit Instructions 1. Disconnect battery and elevate front end of car on either Jack stands or a lift if available 2.Lock steering wheel and remove

More information

7B1210 COBB BMW N54 Charge Pipe

7B1210 COBB BMW N54 Charge Pipe 7B1210 COBB BMW N54 Charge Pipe Installation Instructions Congratulations on your purchase of the COBB BMW N54 Charge Pipe for your BMW. The following instructions will assist you through your installation

More information

TOYOTA TUNDRA COLD AIR INTAKE Preparation SEQUOIA

TOYOTA TUNDRA COLD AIR INTAKE Preparation SEQUOIA Preparation SEQUOIA 2008 - Part Number: PTR03-34070 (5.7L) PTR03-34072 (4.7L) Kit Contents: 5.7L Item # Quantity Reqd. Description 1 1 Lid: Air Filter 2 1 Inlet Pipe: 5.7L 3 1 Air Filter: TRD Conical 4

More information

Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions

Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions Mercedes E63/CLS AMG Carbon Turbo Intake System Instructions The goal of Alpha Performance is to provide the highest quality, best performing products available. By utilizing research and development,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-818C (GUN METAL GRAY FINISH) 2017 Nissan Sentra SR Turbo 1.6T 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157DK

More information

Owner smanual. Banks Techni-Cooler System Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks (2500/3500) USE WITH SYSTEM P/N 25987

Owner smanual. Banks Techni-Cooler System Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks (2500/3500) USE WITH SYSTEM P/N 25987 Owner smanual with Installation Instructions Banks Techni-Cooler System 2013-16 Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks (2500/3500) USE WITH SYSTEM P/N 25987 Gale Banks Engineering 546 Duggan Avenue

More information

INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT

INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT MITSUBISHI LANCER EVOLUTION X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM

More information

INSTALLATION MANUAL. Ford 5.4L F

INSTALLATION MANUAL. Ford 5.4L F INSTALLATION MANUAL Applications Rapid Flow Part Number Ford 5.4L F150 09-10 51200 Parts Included Parts Included and Tools Needed: This section displays the parts included in the package and the tools

More information

INSTALLATION GUIDE NISSAN NAVARA INTERCOOLER KIT P/N PWI65094K

INSTALLATION GUIDE NISSAN NAVARA INTERCOOLER KIT P/N PWI65094K INSTALLATION GUIDE NISSAN NAVARA INTERCOOLER KIT P/N PWI65094K ENGINEERING THE UNFAIR ADVANTAGE Contents CONDITIONAL MANUFACTURERS WARRANTY... 2 WARRANTY VOIDS... 2 WARRANTY DOES NOT COVER... 2 LIMIT OF

More information

Ford 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.

Ford 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation. 1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T

More information

Factory safe air/fuel ratio s for Optimum performance Patent# 7,359,795

Factory safe air/fuel ratio s for Optimum performance Patent# 7,359,795 Part Number SP1125 2007-09 BMW 335i 2008-09 BMW135i 3.0L Twin Turbo L6 This kit is equipped with the Injen/AMSOIL Ea nanofiber dry filters, Ea nanofiber filters do not require oil. 1-2 piece air intake

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazdaspeed Miata

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazdaspeed Miata SHORT RAM SYSTEM Installation Instructions for: Part Number 22-489 2004 Mazdaspeed Miata ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Corolla & 2003 Toyota Matrix XR

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Corolla & 2003 Toyota Matrix XR SHORT RAM SYSTEM Installation Instructions for: Part Number 22-469 2003-2004 Toyota Corolla & 2003 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

SCION xb PERFORMANCE AIR INTAKE Section I Installation Preparation 2.4L I-4

SCION xb PERFORMANCE AIR INTAKE Section I Installation Preparation 2.4L I-4 Section I Installation Preparation 2.4L I-4 Part Number(s): PTR03-52110 Kit Contents Item # Quantity Description Reqd. 1 1 TRD Inlet Tube 2 1 TRD Upper Air Box with HC Trap 3 1 Hump Hose Coupler 4 1 Hump

More information

Kit Part Number:

Kit Part Number: 10-677 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-677 Nissan 350Z 3.5L V6 2007-2008 CARB EO # D-392-30 Short Ram Intake Systems that are pending an Executive Order number (EO#)

More information

COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D A. APPLICATION: E36/7 M-Roadster or M-Coupe 3.

COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D A. APPLICATION: E36/7 M-Roadster or M-Coupe 3. COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0323A APPLICATION: 1998-00 E36/7 M-Roadster or M-Coupe 3.2 Liter PARTS LIST Air Filter Assembly 3 1/2" Tube Intake Shield Silicone Hose Airflow

More information

Instruction Manual P/N: Make: Nissan Model: 370z Year: Engine: V6-3.7L

Instruction Manual P/N: Make: Nissan Model: 370z Year: Engine: V6-3.7L Instruction Manual P/N: 12529003 Make: Nissan Model: 370z Year: 2009-2012 Engine: V6-3.7L Please read the entire instruction manual before proceeding. Ensure all components listed are present. If you are

More information

This kit is equipped with the Injen Ea nanofiber dry filters, Ea nanofiber filters do not require oil.

This kit is equipped with the Injen Ea nanofiber dry filters, Ea nanofiber filters do not require oil. This kit is equipped with the Injen Ea nanofiber dry filters, Ea nanofiber filters do not require oil. Part Number SP1126 2011 BMW E82 135i E90 335i (N55) L6 3.0L (turbo) 1-2 piece TUNED air intake system

More information

Part number SP Mitsubishi Lancer 4 cyl. 2.0L non-turbo. 1- Three piece cold air intake

Part number SP Mitsubishi Lancer 4 cyl. 2.0L non-turbo. 1- Three piece cold air intake Part number SP1835 08-09 Mitsubishi Lancer 4 cyl. 2.0L non-turbo 1- Three piece cold air intake 1- Formed silicone hose (#3158) 1-2 1/2 Injen filter (#1012) 1-2 3/4 straight hose (#3043) 4- Power-Bands.312.040

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Matrix XRS

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Matrix XRS SHORT RAM SYSTEM Installation Instructions for: Part Number 22-466 2003 Toyota Matrix XRS ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

INSTRUCTIONS. INTERCOOLER UPGRADE BMW E82 135i 2008-

INSTRUCTIONS. INTERCOOLER UPGRADE BMW E82 135i 2008- INSTRUCTIONS INTERCOOLER UPGRADE BMW E82 135i 2008- Parts Included: - Intercooler - Left and right side pipes with hoses - 3 Silicone Hoses ( 2.5 x 3 ) - 1 Silicone Hose 90degree 2.5 elbow - 8 Hoseclamps

More information

Installation Instructions

Installation Instructions Installation Instructions Barricade 3.5 in. Bull Bar w/ Skid Plate & 20 in. Single Row LED Light Bar Black (Polished) (210-16 JEEP WRANGLER 4 DR & 2DR) Part# J107785 J107786 Page 1 of 5 PARTS LIST: 1 Bull

More information

MAZDA 3 MPS FRONT MOUNTING INTERCOOLER INSTALLATION

MAZDA 3 MPS FRONT MOUNTING INTERCOOLER INSTALLATION MAZDA 3 MPS FRONT MOUNTING INTERCOOLER INSTALLATION Tools needed: 7mm Hose clamp driver 10mm,12mm sockets and suitable ratchet with extensions Flat bladed screwdriver Pliers Phillips screwdriver KIT CONTENTS

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (Gun Metal Grey Finish) 2015 Ford Mustang 2.

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (Gun Metal Grey Finish) 2015 Ford Mustang 2. Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 26-3001C (Gun Metal Grey Finish) 2015 Ford Mustang 2.3 Turbo ITEM NO. PART NUMBER DESCRIPTION QTY. 1 2-1523C TUBE;

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS N-MT13-1 & N-MT13-2 COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS MUSTANG GT 2015-up PARTS INCLUDED Part Number Descrip on Qty 9-SA-INTAKE-100 Intake Assembly 1 9-SA-HEATSHIELD-100 Heatshield Assembly

More information

Camaro/Trans Am V3 T6 Kit Installation Instructions

Camaro/Trans Am V3 T6 Kit Installation Instructions 1998-2002 Camaro/Trans Am V3 T6 Kit Installation Instructions A- Driver s Side Manifold B- Passenger s Side Manifold C- Crossover Pipe Parts List D- 2.5 v-band Clamp - Quantity-2 E- Downpipe F- Heat Wrap

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08P21-STX-200 2008 MDX BII 37680 Issue Date AUG 2007 PARTS LIST Left bracket A Left front fender flare Left bracket B Left front bumper

More information

Step 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.

Step 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold. LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the

More information