Installation Manual Lock-Switch KIA Sorento V3 Installation Manual Lock-Switch V3 for KIA Sorento (02-06) and KIA Sorento (07-09)
|
|
- Stephen Park
- 5 years ago
- Views:
Transcription
1 Installation Manual Lock-Switch V3 for KIA Sorento (02-06) and KIA Sorento (07-09) Note: A any work on the electrical system of a car before should the battery be disconnected at the negative terminal to prevent possible short circuits.. Damages caused by improper installation, can't be accepted. Notes: When working with the cars plastics, do it always in warm weather (> 15 C) or heated with a hair dryer. Tools Required: Phillips, blade screwdriver, eventually scraper and / or wooden wedge, wire cutter, electrical tape, preferably soldering iron, knife, wire stripper, heat shrink tubing How to connect wires: The old wire strip about 1-2 cm, not cut it. The wire which is to connect, strip also 2 cm and wrap around the other wire. Then, solder and wrap electrical tape around. When are two wires to connect together, both wire strip about 2 cm and wrap together. After solder this new connection, wrap electrical tape around or alternatively use heat shrink tube. Optional can used the crimp plugs. Please don't use Electrical Pigtail Connectors, they have a bad reliability. - Seite 1 von 13 -
2 Content: - Lock-Switch: Panel with electronic, with button and without any other switches (cruise, ESP, headlight range adjustment,... - Wire harness: Plug with 6*/8* Wires, (+ Plug with one wire)* - Shorting Plug, Nut - Additional Display* *depends on kind of features Lock-Switch (Example, can have a other look) Shorting Plug + M6 Flanged Nut Wire harness with additional wire for ABSoff and second plug (not included with additional display) Additional Display - Seite 2 von 13 -
3 Step 1 (disassembling cover): At first, the left cover between door and dashboard must be uncliped. Take a Japanese scraper or a wooden wedge and press it in the slot and lever out. Fold it away and pull it out. Now disassemble the cover under the steering wheel, unbolt the both lower screws and these both screws at the left side. - Seite 3 von 13 -
4 Now pull the cover, there are three clips... and at the right side over the ignition switch use a scraper to lever out. Unplug the wire harness from the ESP-, Cruise- or headlight range adjustment switches (edge clips pressed in and pull the plug back). The OBD plug unclip and the engine hood opener pull to the left out of the slot. - Seite 4 von 13 -
5 The bowden cable move to the right out of this slot (notice this disassembling way for assembling at the end). On the right side of the car lever out the sillboard cover, use a wooden wedge and pull upwards. Take attention of the guide lug at the end of this cover. Unbolt the screw and pull the cover to the inside of the car, three clips are there. Step 2 (disassemble panel): 4 plastic lugs hold the panel in the cover, press they together and the panel can take away. Or take a Japanese scraper an lever out the panel at top an bottom. - Seite 5 von 13 -
6 The switches are also held with two plastic lugs, press them together and push the switches to the front. Step 3 (electrical connection): Overview of the plugs under the cover drivers side (under the steering wheel). Configuration Sorento BJ At the two plugs (red arrows, black (2) and white vertical plug (1) ) are the signals, which are needed. In addition is the original wire harness of the original 4WD switch needed. 1 Configuration Sorento BJ Connect (solder) the white wire of the new lock switch wire harness (following only LS) with the red/black wire from the wire harness of the original 4WD switch, also the blue wire (LS) with the blue/orange wire. Isolate with electrical tape. - Seite 6 von 13 -
7 Sorento (* optional wire version): At the shown lower plug (black (2) ) connect the green wire (LS) with the green/black wire (pin 2, left side of the plug) of the Sorento harness. Isolate with electrical tape. Sorento BJ07-09 (* optional wire version): At the shown left plug (black (2) ) connect the green wire (LS) with the green/black wire (pin 2, left side of the plug) of the Sorento harness. Isolate with electrical tape. At the right white Plug (1) connect the thick yellow wire with red wire from LS. Isolate with electrical tape. Over these plugs under the dashboard is a good ground contact with a bold, fix the black wire (LS) with the ring eye, use the included nut. - Seite 7 von 13 -
8 Now the drilled two wires (green & yellow/green, possible wrapped) place to right side of the car, first fix at the steering column, and under the blower to the right. Install the wires under the floor at the passenger side complete to the right. Sorento 02-06: Overview of the plugs at the right side, the lowest black plug is needed. Sorento 07-09: Overview of the plugs at the right side, the highest black plug is needed. At this plug cut the yellow wire (pin 4, next green/orange). - Seite 8 von 13 -
9 Sorento 02-06: The green wire from LS wire harness must be connected with the cutted yellow wire, which comes out of the plug. Connect the green/yellow wire from LS with the other end of the yellow wire, which comes from the harness. Isolate. Sorento 07-09: The green wire from LS wire harness must be connected with the cutted yellow wire, which comes out of the plug. Connect the green/yellow wire from LS with the other end of the yellow wire, which comes from the harness. Isolate. Installation is complete, now place the net lock switch panel in the cover and plug in the other switches (ESP, cruise, headlight range adjustment). Attention, please never press on the little wheel from the headlight range adjustment, it cracks. Plug in the new plug(s) from the lock switch harness an test the installation. All things are OK, when nothing other happens, as in the manual is described. When the 4WD lamp begins to flash, then are the wires on the right side interchanged. The included shorting plug is used, when new lock switch should be dismount, this plug come on the new lock switch wire harness to reinstall the original function of the 4 wheel drive. Than the original panel can used. If you have any questions, please call us or write an . - Seite 9 von 13 -
10 Additional wiring ABSoff Sorento 02-06: (optional) The addition wires (two drilled black wires) for the ABSoff function must be install in the engine room, the best way to bring them trough the splash-board is a little opening under the dashboard, right handed to the steering column. View from the engine room. Make a hole in the existing rubber bushing and push the wires trough. This ist the ABS controller plug. The red locker must be pulled to the engine, than it's possible to unplug this plug. Remove some electrical tape and a wire strap press the little lug into the case and now the case can move to the front and take away. the blue (and shortest) wire (pin 15) must be cut and each end must be connect with one of these black wires. It's not urgent which one of these two black wire you take. Reinstall the plug, ready for testing. - Seite 10 von 13 -
11 Additional wiring ABSoff Sorento 07-09: (optional) The additional wire for the ABSoff function is placed from top the cover left handed side in foot room of the driver, where the fuse box is. There must be unplugged the fuse for ABS. Use the new fuse adapter. In the wire harness ist a new fuse holder, a backup fuse (if necessary) is included. - Seite 11 von 13 -
12 Additional Display (optional): First, unfix the instrument cluster frame, take a wooden wedge or something else and lever out the frame on both sides, left and right. The unfixed Frame. Now take the wire with the plug and handle it behind the frame placed a little bit upper, there is a hole in the instrument cluster. And manage the wire behind the cluster down to the lock switch. The addition display is now ready for fixing it with the adhesive tape under the display. Take attention of the place for fixing it, there are some lug at the instrument cluster. - Seite 12 von 13 -
13 Now can the wire plugged it in the right socket (4 pins) of the lock switch. Reinstall the instrument cluster frame and ready. On the Back side of the lock switch is es potentiometer (red circle). Here you can adjust the brightness of the display. Turn it right increases the brightness, turn to left decreases. Please use a little screw driver and be carefully. - Seite 13 von 13 -
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 12035 SYSTEM 2012 RIDGELINE Issue Date NOV 2011 PARTS LIST Security System Attachment Kit: P/N 08E55-SJC-101 Flange bolt Unit bracket
More informationTOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: 08586-OC910 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio NOTE:
More informationM GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET
Please contact the Ford Racing Techline for the most current instruction information @ (800) FORD-788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The following
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory USB ADAPTER Application 2014 INSIGHT Publications No. AII 50655 Issue Date OCT 2013 PARTS LIST USB Adapter Attachment Kit P/N 08B28-TM8-100A 6 mm Flange nut Control
More informationFOG LAMPS INSTALL KIT
FOG LAMPS INSTALL KIT PT CRUISER INSTALLATION INSTRUCTIONS Read entire instructions thoroughly before starting. For proper aiming of fog lamps, follow procedures in the service manual. NOTES: Left and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CIVIC All 30175-31616 2 AND 4-DOOR P/N 08E10-SNA-100 Issue Date DEC 2005 NOTE: The interior illumination lights cannot be installed on 2-door
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08E10-TA0-100 Application 2008 ACCORD 2-AND 4-DOOR Publications No. AII 35358 Issue Date AUG 2007 PARTS LIST Ambient Light Kit 2 Ambient lights Fuse label Washer
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HITCH Application 2009 CR-V Publications No. AII 40373 Issue Date AUG 2008 PARTS LIST Plain washer, 12 mm Trailer Hitch Kit P/N 08L92-SWA-100 Trailer hitch 6 Spring
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. 2010 CIVIC All 42479 2- AND 4-DOOR P/N 08E10-SNA-110 Issue Date AUG 2009 NOTE: The interior illumination lights cannot be installed on 2-door
More informationTOYOTA PRIUS FOG LIGHT (Halogen or LED)
Part Number: TPR-413 / TPR-813 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Lower Grill 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness Bag Hardware Bag Contents Item
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALL KIT Honda S2000 Document# 19-0063 Support: info@radiumauto.com WARNING: DO NOT SMOKE WHILE WORKING ON FUEL SYSTEMS. KEEP SPARKS AND OPEN FLAMES AWAY FROM
More informationGauge Wiring Instructions
Thank you for purchasing the Track Dog Racing Gauges. These instructions are for wiring the Westach brand gauges with the TDR gauge panel for all model years of the Miata. Refer to the installation instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08E50-TK6-100 Application 2010 FIT (BASE MODEL) Publications No. AII 42212 Issue Date AUG 2009 The security system will only work if the vehicle is equipped with
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application CR-V Publications No. AII 32953-34081 Issue Date NOV 2006 PARTS LIST 2 Corner sensor clips Backup Sensor Attachment Kit P/N 08V67-SWA-100A Back-up sensor
More informationINSTALLATION INSTRUCTIONS FORD POWERSTROKE PICKUPS MODEL YEAR
p p INSTALLATION INSTRUCTIONS FORD POWERSTROKE PICKUPS MODEL YEAR 2005-2006 www.dieselturbolifesaver.com Diesel Turbo Lifesaver (DTLS) is a computer controlled device that allows you to set an automatic
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-S0X-100 1999-2001 ODYSSEY AII 20677 Issue Date AUG 1999 PARTS LIST 2 Fog lights Switch Fuse label Right bracket Relay B, 4-pin
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2010 ODYSSEY Publications No. AII 41818 Issue Date JUNE 2009 PARTS LIST Right center sensor clip (Black) Backup Sensor Attachment Kit P/N 08V67-SHJ-101C
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2010 CR-V Publications No. AII 42602-42850 Issue Date OCT 2009 PARTS LIST Fog Light Kit (With Auto Lights) P/N 08V31-SWA-100A Fog Light Kit (Without Auto
More information* * Inside Toyota Avalon. Tools Required IMPORTANT
Revision 08/02/16 2013- Toyota Avalon IMPORTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call Crutchfield
More informationIlluminated Cup Holders Hyundai Elantra (GLS, Limited, Coupe)
Illuminated Cup Holders 2011-2015 Hyundai Elantra (GLS, Limited, Coupe) Thanks for purchasing this Cup Holder Illumination Install Kit! If you have any questions or feedback please email me direct at info@accentglowled.com
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationInstructions on installing the R/R to the front battery cover.
April, 2008 Instructions on installing the R/R to the front battery cover. Please read all of the steps so you will be familiar with the complete relocation installation first. The purpose of this relocation
More informationA. Preparing the charge harness. Start by removing the plastic covers by the battery terminal.
twist battery relocate kit and harness. Step 1 A. Remove battery. Start by removing the negative battery cable and then the positive. After removing the battery cables remove the battery hold down bracket.
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS S (LX, EX) CIVIC 2- AND 4- DOOR AII 25449 Issue Date SEP 2003 NOTE: Fog Lights cannot be installed if the vehicle is equipped with an optional
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS S (DX, HX, VP) 2005 CIVIC 2- AND 4- DOOR AII 27865-30866 Issue Date SEP 2005 NOTE: Fog Lights cannot be installed if the vehicle is equipped
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2008 ACCORD 2-DOOR Publications No. AII 37561-38377 Issue Date NOV 2007 PARTS LIST Control unit bracket (L4) Back-up Sensor Attachment Kit P/N 08V67-TE0-100A
More informationRear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number )
Rear Vision System Liftgate Emblem Camera for Aftermarket Display 2009-2012 Ford Flex (Kit part number 1008-6509) Kit Contents: Liftgate Emblem Mount with Camera Chassis Harness with RCA (Note: In some
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26042-26353 XM INTERFACE ODYSSEY EXCEPT EX-L WITH NAVI/RES Issue Date FEB 2004 PARTS LIST 8 Wire ties XM Radio Attachment P/N 08B15-S0X-100
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08E10-TK6-100 Application 2013 FIT Publications No. AII 13198 Issue Date JULY 2012 PARTS LIST Ambient light kit 2 Ambient lights 6 Wire ties Fuse label 2 Grommets
More informationProjector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation
Projector39/Umnitza BMW Headlight & Re-Installation for E39s Predator Angel Eyes, and Lamin-X Installation Now it is time to remove the headlights! Obviously you have to open the hood to do this. 100_3630.jpg
More informationTOYOTA RAV TVIP V3
Section I Installation Preparation Part Number: 08586-4A872 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 Status Monitor 3 1 Piezo Buzzer 4 1 V3
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SDN-100 2004 ACCORD 2-DOOR AII 25735 Issue Date SEP 2003 NOTE: The outside temperature gauge can not be installed in a vehicle
More informationCERTAIN TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE
PAGE 1 OF 19 CERTAIN 2015-2017 TRANSIT VEHICLES EQUIPPED WITH A TRAILER MODULE TRAILER MODULE FUSE AND FOOTWELL DRAINAGE HOLE OVERVIEW In the affected vehicles, it may be possible for water to pool and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 23086 SYSTEM CR-V Issue Date NOV 2001 PARTS LIST Security System P/N 08E51-EP4-100 Security System Attachment P/N 08E55-S9A-100 Security
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 38137-38714 Accessory HandsFreeLink 2008 ODYSSEY Issue Date JAN 2008 PARTS LIST Attachment Kit P/N 08E02-SHJ-100B trim Fuse label Fuse
More informationInstalling Ignition Coil relay
Installing Ignition Coil relay Above is a schematic diagram of the coil relay modification. All it really does is, it uses the existing 12 Volt positive that normally powers the coils, to power a relay,
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Security System Kit (sold separately) P/N 08E51-EP4-101
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30510 (LX) 2006 PILOT Issue Date SEP 2005 PARTS LIST Security System Kit (sold separately) P/N 08E51-EP4-101 Security system control
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory BACKUP S Application 2012 ODYSSEY Publications No. AII 46724 Issue Date SEP 2011 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-TK8-100A Right center sensor clip
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-SCV-102 2008 ELEMENT AII 36531 Issue Date MAY 2007 PARTS LIST 15 Wire ties 2 Fog lights 4 Wire ties with clip Switch harness
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM ACCORD 2-DOOR (LX/EX L4, LX V6) AII 25749 Issue Date FEB 2004 PARTS LIST Double-sided adhesive tape XM Radio Attachment Kit : P/N
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD AII 24050 4-DOOR P/N 08V31-SDA-100 Issue Date AUG 2002 NOTE: The outside temperature gauge cannot be installed in a vehicle with
More informationInstallation Instructions
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2011 CR-V Publications No. AII 44647 Issue Date AUG 2010 PARTS LIST Trailer Hitch Kit P/N 08L92-SWA-101 Trailer Hitch Harness Kit P/N 08L91-SWA-100 Trailer
More informationFord High Idle Kit PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
U 17 December 2014 2003-2004 Ford High idle Kit (I-00320) 1 Ford High Idle Kit 2003-2004 Ford 6.0L Diesel (Automatic transmission Only) 1036609 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD Engine
More informationBefore disconnecting battery Ground (GND) strap obtain security code for radio with antitheft
Page 1 of 14 Volkswagen > New Beetle > 1998-2005 Body Interior 70 - Interior trim Instrument panel, removing and installing WARNING! Disconnect battery Ground (GND) strap before working on electrical system,
More informationWPS-104 Heater Installation Instructions For 500EFI, 700 XP, & Crew Applications
WPS-104 Heater Installation Instructions For 500EFI, 700 XP, & Crew Applications ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A RANGERWARE WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK Application 2010 ACCORD 2 AND 4-DOOR Publications No. AII 42231 Issue Date AUG 2009 PARTS LIST HFL retainer HFL Attachment Kit P/N 08E02-TA0-100
More informationLiteDOT Installation Document
LiteDOT Installation Document This document designed to aid in installation of LiteDOT s on Jeep TJ models, other models are similar. NOTE: Installing LiteDOT s on a Jeep where the 2 necessary mounting
More informationSCION tc SECURITY (V5) Preparation
Preparation Part Number: PT398-21070 Kit Contents Item # Quantity Reqd. Description 1 1 2 1 GBS ECU Hardware Bag Contents Item # Quantity Reqd. Description 1 1 V5 Security ECU 2 1 ECU Mounting Bracket
More informationInstallation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)
Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well
More informationGeneral Applicability: KIA Sorento. Issues Current Kit does not allow for CAN DATA remote access
Document #730135 Created ACH 08/02/2018 Revised ACH 08/20/18 A2 General Applicability: 2018-19 KIA Sorento Issues Current Kit does not allow for CAN DATA remote access Kit Contents: Item# Component Description
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory BACKUP S Application 2014 CR-V Publications No. AII 49959 Issue Date JULY 2013 PARTS LIST Right corner sensor clip (Black) Backup Sensor Attachment Kit P/N 08V67-T0A-100
More informationBBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt)
BBK LONG TUBE HEADERS (99-04 GT, Mach 1, Bullitt) Install Time: Approx. 8-10 hrs Parts Needed: BBK Long Tube Headers Shorty mid pipe X/H O2 wiring harness extensions Hi-temp thread locker Tools Required:
More informationTOYOTA FJ CRUISER TVIP V5 Preparation
Preparation Part Number: 08586-36822 Conflicts Do not be installed in vehicles with factory Anti-theft alarm, or Vehicle without Factory Keyless Entry Systems. Recommended Sequence of Application Item
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationSPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER. Read entire instructions thoroughly before starting. INSTALLATION INSTRUCTIONS TOOLS REQUIRED:
Read entire instructions thoroughly before starting. TOOLS REQUIRED: SPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER INSTALLATION INSTRUCTIONS Complete socket set Phillips screwdriver Torx drivers Wire strippers/cutters
More informationDodge Cummins Positive Air Shutoff
1998-2002 24V 5.9 Dodge Cummins Positive Air Shutoff (I-00181) 1 INSTALL MANUAL 1998.5-2002 5.9 Dodge Cummins Positive Air Shutoff P/N# 1036719 P/N# 1036719-M UPLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Accessory Hands Free Link Application 2009 ACCORD 2 AND 4-DOOR Publications No. AII 40055 Issue Date JULY 2008 PARTS LIST HFL Attachment Kit P/N 08E02-TA0-100 HFL trim
More informationTurn Signal / Horn Kit PN 7101 by All years Polaris RZR 1000 and RZR 900, 900-4, 900 trail, 900S and 900XC STOP - THIS KIT IS DESIGNED
All years Polaris RZR 1000 and 1000-4 2015 RZR 900, 900-4, 900 trail, 900S and 900XC STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR ALL YEAR AND MODEL POLARIS RZR 1000 AND 1000-4. ALSO THE 2015 POLARIS RZR
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Accessory Hands Free Link Application 2008 ACCORD 2 AND 4-DOOR Publications No. AII 38281 Issue Date NOV 2007 PARTS LIST Attachment Kit P/N 08E02-TA0-100 trim retainer
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 22903-22963 ODYSSEY Issue Date MAY 2002 PARTS LIST Subwoofer Kit: P/N 08A39-EP7-100 Subwoofer 2 Cushion tapes 8 Wire ties (1 not used)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08E10-TA0-110A Application 2012 ACCORD 2- AND 4-DOOR Publications No. AII 46501 Issue Date AUG 2011 PARTS LIST Ambient Light Kit Fuse label 2 Ambient lights Washer
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER(S) REQUIRED FOR INSTALLATION: Dual Rear Seat USB Charge Port Kit Titan T99Q7 6LB0A (Excluding Single Ca T98Q7 5ZW2A (Metal
More informationTOYOTA PRIUS 2004 TVIP V2 (GBS ADD ON) Section I Installation Preparation
Section I Installation Preparation Part Number: 08586 47840 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 3 1 ECU Mounting Bracket Hardware Bag
More informationZ8 Engine Start Button Install for the BMW E46 3 Series
Z8 Engine Start Button Install for the BMW E46 3 Series This write up is a specific installation of a Z8 engine start button on the E46, but it can be used as a general guide for an engine start button
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24664-25319 SYSTEM 2003 CR-V Issue Date MAY 2003 PARTS LIST Security System (sold separately) P/N 08E51-EP4-100 Security System Attachment
More informationAmp & Speaker Upgrade Install Instructions for Victory Cross Country
Amp & Speaker Upgrade Install Instructions for Victory Cross Country Tools Needed: 13mm Socket 4mm Ball Head Allen Socket 5mm Allen Wrench 10mm Wrench Wire Cutters Wire Strippers Phillips Screwdriver Pocket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2011 ODYSSEY (EXCEPT LX) Publications No. AII 43923 Issue Date SEP 2010 PARTS LIST Remote Control Engine Starter Unit Kit P/N 08E91-E22-101A
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)
More informationParts and Accessories Installation Instructions
Parts and Accessories Installation Instructions Installation kit, sound module MINI (R5) Cooper S (R53) Left-hand drive (LHD) Not suitable for vehicles with option SA 69 (navigation system with on-board
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Mirror Display Dodge Ram Kit Contents: Instruction Sheets Template Chassis Harness Endgate Handle with Camera Wire Ties (Qty: 17) Bottle of ZTech Plug for Non-Locking Endgates (Optional)
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Rear Vision System Mirror Display 2013-Current Ram (Kit part number 1009-9518) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Rear
More informationINSTALLATION INSTRUCTIONS
2015 - Ford Mustang Qi Wireless Charging Kit (Kit # FDMC-1222) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Qi Wireless Charging
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. REAR VIEW CAMERA ATTACHMENT PILOT AII 23620 Issue Date MAY 2002 PARTS LIST Attachment Kit : P/N 08B21-S9V-100 Control unit harness Rear
More informationDodge Cummins Positive Air Shutoff
21 October 2011 1998-2002 24V 5.9 Dodge Cummins Positive Air Shutoff 1 1998.5-2002 5.9 Dodge Cummins Positive Air Shutoff P/N# 1036719 P/N# 1036719-M UPLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION 21
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SNA-100 2007 CIVIC HYBRID AII 33829 Issue Date SEP 2006 PARTS LIST Fog light harness Right fog light Left fog light Subharness
More informationTOYOTA VENZA HANDS FREE BLU LOGIC Preparation
TOYOTA VENZA 2009- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 36765 S 2008 RIDGELINE Issue Date JUN 2007 PARTS LIST Relay Fog Light Kit P/N 08V31-SJC-100 Right fog light 15 Wire ties Left fog light
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CIVIC AII 24171 S 2- AND 4-DOOR Issue Date (DX, HX) AUG 2002 NOTE: Fog Lights cannot be installed if the vehicle is equipped with an optional
More informationTOYOTA SEQUOIA TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: PT398-34111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts Do not install into vehicles without RKE system. Recommended Sequence of
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SVA-110 2007 CIVIC 2-DOOR All33536-34848 Issue Date FEB 2007 PARTS LIST 11 Wire ties Right fog light Clip Left fog light 4 Stepped
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S CIVIC 2 AND 4-DOOR (EX, LX) AII 24188 Issue Date AUG 2002 NOTE: Fog Lights cannot be installed if the vehicle is equipped with an optional
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SDA-102 2007 ACCORD 4-DOOR AII 32672 Issue Date JULY 2006 NOTE: Fog lights can be installed in a vehicle equipped with a factory
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2012 ODYSSEY (EXCEPT LX) Publications No. AII 46745 Issue Date SEP 2011 PARTS LIST Remote Control Engine Starter Unit Kit P/N 08E91-E22-101A
More informationLEXUS RX TVIP V2 PREPARATION
PREPARATION Part #: PT398-48090 Conflicts: NOTE: Part number of this accessory may not be the same as the part number shown. Do not install into Vehicles without Factory Alarm System. Kit Contents GBS
More information2005+ Mustang Trunk Lid Release and Trunk Lights Installation
There is no warranty expressed or implied by this document, you follow these instructions at your own risk. These instructions worked for me, but your experience may vary. The final product of these instructions
More informationInstallation Instructions For The O.CT S4 Boost Gauge
Installation Instructions For The O.CT S4 Boost Gauge The ultimate power display FROM AND Stratmosphere 28 Boulder Creek Drive Rush, NY 14543 585-533-1777 O.CT Tuning Oberscheider O.CT-Tuning, Reichsstr.
More informationShelby GT500 Front Fascia Conversion Kit (05-09 All) Item # Installation Time: 1 Day. Required tools:
Shelby GT500 Front Fascia Conversion Kit (05-09 All) Item #53611 Installation Time: 1 Day Required tools: Phillips Screw driver 10mm Socket + Ratchet/Wrench 8mm Socket + Ratchet/Wrench 5mm Socket + Ratchet/Wrench
More informationTOYOTA HIGHLANDER TVIP V2 (GBS ADD ON) Preparation
Preparation Part Number: 08586-48070 Kit Contents Item # Quantity Reqd. Description 1 1 Wire Harness 2 1 GBS ECU 3 1 ECU Mounting Bracket Hardware Bag Contents Item # Quantity Reqd. Description 1 1 Microphone
More informationDodge Cummins Positive Air Shutoff
10 June 2013 1998-2002 24V 5.9 Dodge Cummins Positive Air Shutoff 1 1998.5-2002 5.9 Dodge Cummins Positive Air Shutoff P/N# 1036719 P/N# 1036719-M UPLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION 10 June
More informationProcedure. These guidelines can be found in the "Accessory Installation Practices" document.
Toyota Tundra 207 LED Illumination Package Part Number: 0006-00069 (Interior and Exterior) Accessory Code: LL000 Conf licts V ehicles with Option Code BZ Color Applicability/Trim Level Kit Content 4 Puddle
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 27176 2005 CR-V Issue Date P/N 08V31-S9A-114 SEP 2004 PARTS LIST 25 Wire ties Left fog light 6 Washer-bolts Right fog light 6 Spring
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08E49-S2A-100 2004 S2000 AII 26325 Issue Date OCT 2003 PARTS LIST Hood switch harness TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver
More informationLED Fog Light. Conflicts Note: 1832, 1852, 1856, 1872, General Applicability Fits Models
LED Fog Light Year & Model Part Number 2017 Corolla TCO-817 Conflicts Note: 1832, 1852, 1856, 1872, 1874 General Applicability Fits Models 1863 1866 1864 1865 Additional Items Required For Installation
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Illuminated Kick Plate APPLICATION: INFINITI M45 (2010) PART NUMBER: G6950-1MA0B KIT CONTENTS: Item QTY Description SERVICE PART NUMBER
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2007 CIVIC 2-DOOR All33536-34068 Issue Date SEP 2006 PARTS LIST 11 Wire ties Right fog light Clip Left fog light 4 Stepped screws 2 Washer
More information