NORDcanopy. Installation, use and maintenance manual

Transcription

1 NORDcanopy Installation, use and maintenance manual

2 Installation, use and maintenance manual The choice of kitchen extractor hoods depends on the size of the kitchen equipment. The hood must be mm wider / longer than the device. It is recommended to install the hood over the cooking equipment so that the distance between edge of the hood and the device in vertical direction would be from 00 to 00 mm. When the hood is installed over an oven, the hood must reach over the oven at least 00 mm, so that all vapour is removed from the air when the oven door is opened. The recommended height of the hood from the floor is,000 mm (,900 to,00 mm). > h >0, x h Figure. The arrangement of the kitchen hood

3 Installation of the hood The hoods belonging to NORDcanopy product group are delivered as modules. Thus, the installation process is not dependent on the type or the size of the hood. NB! To suspend the hood onto the ceiling use threaded rods, nuts and washers (not included) not smaller than M8.. mounting bracket. threaded rod (min. M8). nut (min. M8). washer Figure. Suspending the hood from the ceiling The hood consisting of several modules each module will be "hung" separately. Then the modules are levelled together as a kit, and their tops are connected with bolts and nuts (not included) (see Figure ). The hood will me hung from the ceiling, even if it is close to the wall. NB! The stainless material protection films of the hood (except. between the modules interconnected exposed walls) can be removed just before the system becomes operational Figure. Modular hood installation (figure shows type HKS- hood) Images are for illustrative purposes We reserve the right to make changes

4 Installing the kitchen hood accessories. Installing the grease collection container The grease collection container () is installed on rails () (see Figure 5). Fasteners are not included in the kit Figure. Connecting the modules from hood top (shown in Figure HKS-type hood of two modules) ITEM NO. DESCR M6x M8 M8 w Paigaldamine - KA Triin.0.06 / ITEM NO. DESCRIPTION QTY. ITEM NO. DESCRIPTION QTY. Figure 5. Installing the grease collection container Collection tray M6x6 bolt Fastening brackets. Installing HFK grease filters M8 nut M8 washer HFK grease filters () are installed into the extractor module with handles (see Figure 6). Triin.0.06 ITEM NO. DESCRIPTION Collection tray QTY. Triin.0.06 Fastening brackets / / Figure 6. Installing HFK grease filters Paigaldamine - LISAD Triin.0.06 Paigaldamine - KATUSTE LIITMINE / Paigaldamine - LISAD ITEM NO. DESCRIPTION QTY HFK grease filter Paigaldamine - LISAD Triin.0.06 /

5 . Cover Plate Installation Cover plates are used to conceal pipes between the hood and the ceiling. The L-profiles () and the fastening profiles () are attached to the ceiling hood. Then the lateral cover plates () are riveted onto the L-slat, the first set (rear) cover plate () is installed and riveted onto the lateral cover plates (see Figure 7)..... Figure 7. Cover Plate Installation In case of multi-module hood the first (back) cover plates are riveted to each other. Then the cover plates are installed and riveted to the lateral sides of the cover plates (see Figure 8). Pealtvaade Figure 8. Cover Plate Installation for the module hoods In case of wall side hood arrangement the inner slat (5) is fixed to the wall. Then, the side cover plates are riveted to the L-slat and inner slats, the first cover plate in installed and it is riveted onto the lateral cover plates (see Figure 9). Images are for illustrative purposes We reserve the right to make changes 5

6 5 Top view Sein wall 5 Figure 9. Attaching the cover plates onto the EESTVAADE wall EESTVAADE EESTVAADE EESTVAADE Vahelagi Intermediate Vahelagiceiling Generally, the cover plates are not attached onto the ceiling. In case of suspended ceiling the ceiling slats (6) (not included) are attached to the cover plates and the ceiling panel is attached to the ceiling slat (see Figure 0). Suspended Ripplagiceiling Ripplagi 6 6 Figure 0. Attaching the cover plates onto suspended ceiling, intermediate ceilings. Kitchen hood lighting. Surface-mounted luminaries As a standard NORDcanopy kitchen hoods use luminaries with fluorescent ITEM NO. tubes ITEM in a NO. plastic DESCRIPTION housing DESCRIPTION () with QTY. QTY IP 65 protection class. Each luminary is equipped with a power supply cable (.5 mm, length: L-list.5 m) L-list () and 8 8 a junction box (see Figure ). Covering board Covering (side) board (side) 6 For exchanging the fluorescent tubes () the clips holding the protective glass of the luminary 6List (not included) protection List (not included) - glass - () are opened, and then the protective glass is removed. After exchanging the fluorescent lamp the protective glass of the luminary is sealed again with clamps (see Figure ). Triin Triin ETS NORD AS / Paigaldamine Paigaldamine - KATTEPLAADID - KATTEPLAADID / 6 Figure. Surface-mounted luminary ITEM NO. DESCRIP Lighting f Cab Light dif Tube

7 . Integrated luminary Custom made NORDcanopy kitchen hoods use luminaries with fluorescent tubes in a plastic housing () with IP 65 protection class. Each luminary is equipped with a power supply cable (.5 mm, length:.5 m) () and a junction box (see Figure ). For exchanging the fluorescent tubes () the screws holding the protective glass of the luminary protection glass () are opened, and then the protective glass is removed. After exchanging the fluorescent lamp the protective glass of the luminary is sealed again with screws (see Figure ). Figure. Integrated luminary Surveying the kitchen hood and air flow regulation The hoods in the NORDcanopy product group are provided with measuring nozzles (), which are located in the lower part of the chamber (see Figure ). Paigaldamine - VALGUSTI NB! When taking measurements, the HFK Triin grease filters.0.06 must be installed and cleaning door closed (models HKS, HKAS, HKTS). To adjust the exhaust air volume the guillotine damper () is used, which is located behind the HFK grease filters (). The suitable position of the damper is found on the basis of the measurements (see Figure ). To DESCRIPTION Default/ adjust the guillotine damper for steam QTY. traps HKA and HKAS (see Figure ), remove the air guiding plates Lighting fixture (0) from the hood. ITEM NO. Cable Light diffuser For adjusting the supply air (models HKS, HKAS, HKTS) the chords (6) will be used to change the position of Tube the adjusting plate (5) in the intake chamber (5). (See Figure ). The operating air velocity is regulated by respectively opening or closing the additional supply air dampers (8) (see Figure ). Paigaldamine - VALGUSTI ITEM NO. DESCRIPTION Default/ QTY. Lighting fixture Cable Light diffuser Tube / Triin.0.06 S NORD AS / HKS - Measuring nozzles - HFK grease filter - Supply air cleaning door - Guillotine damper 5- Supply air adjusting plate 6- Adjusting chords 7- Junction box 8- Additional supply air damper 9- Grease collection container 0- Lighting cable - Luminary Figure. Supply and exhaust air kitchen hood details Images are for illustrative purposes We reserve the right to make changes 7

8 HKAS - Measuring nozzle - Supply air cleaning door - Supply air connector - Supply air adjusting plate 5- Exhaust connector 6- Guillotine damper 7- Lighting cable (.5) 8- Junction box 9- Mounting angles 0- Condensation nozzle - Detachable condensation plates - Luminary - M6 6 hexagon screws Figure. Steam trap details K-numbers for measuring air volume. Kitchen hoods with height up to 00 mm: - Exhaust K-value = 8,5 (per filter) - Intake, additional air supply closed, per m of front panel: SPx, K=9,8 SPx, K=0,7 SPx, K=0, Kitchen hoods with height up to 550 mm: - Exhaust K-value =,5 (per filter) - Intake, additional air supply closed, per m of front panel: SPx, K=,9 SPx, K=9, SPx, K=59, Kitchen hood maintenance The frequency of kitchen hood cleaning depends on the intensity of use of the kitchen. Generally, the wall surfaces of the hood are cleaned during an ordinary kitchen cleaning routine and the HFK grease filters are cleaned based on their appearance, preferably the filters are washed at the end of each working day. NB! Do not use rough or abrasive agents, chlorine or bleach when cleaning the hood. Cleaning the hood wall surfaces All kitchen hood inner and outer surfaces, including luminary, is cleaned with soapy water or neutral detergents. After cleaning the surfaces must be thoroughly rinsed to prevent dangerous implications from cleaning agents and high temperatures interaction. NB! The hood should never be cleaned if any of its surfaces are hot. The clean the exhaust chamber the HFK grease traps have to be removed from the hood. To clean the inlet chamber (models HKS, HKAS, HKTS) the cleaning hatch is removed from the hood (). To do this the cleaning hatch is rotated by means of the handles until it can be removed from the hood (see Figure 5). Figure 5. Removing the inlet chamber cleaning hatch 8

9 Cleaning the HFK grease filters To clean the grease filters they are removed from the hood with handles. Flowing grease is poured into sewers and the filters are washed by hand or in the dishwasher or cleaned with steam. Clean filters are placed back into the hood. Cleaning the grease collector The grease collector is removed at the same time with cleaning of the filters, discharged into sewage and is washed by hand or in the dishwasher or cleaned with steam. NB! The grease box should be checked regularly and emptied if necessary. Images are for illustrative purposes We reserve the right to make changes 9

10 Adress: Phone: Peterburi tee 5 5 Tallinn info@etsnord.ee