F4-VB Spray Gun Plasma Spraying. Parts List PL EN 06

Transcription

1 F-VB Spray Gun Plasma Spraying Parts List PL 0333 EN 06 Oerlikon Metco 1/2015

2 Oerlikon Metco Switzerland Rigackerstrasse 16 CH-5610 Wohlen Spare parts categories C = Consumable Parts Parts subjected to major wear during normal operation. These parts require replacement on a regular basis. Recommended in order to avoid downtimes. W = Wear Parts Parts used for maintenance service. These parts are likely and expected to wear out during the life of the product. Wear parts are not subject to warranty. K = Critical Parts Parts recommended in order to guarantee maximum availability of component.this prevents downtime caused by delay in procurement. Warranty isclaimer Installing non-oerlikon Metco spare parts on Oerlikon Metco equipment.

3 F-VB Spray Gun 1 List of recommended spare parts for F-VB Spray Gun fvb-wear Pos. esignation Qty Cat. Old Art. no. Art. no. 1 Electrode F 1 C , 11 Powder injector -- C depends on nozzle 18 Insulating intermediate body 1 K Nozzle 1 C see page 7 25 O-ring electrode 12.2x W O-ring nozzle front 29.87x W O-ring nozzle rear 23.7x W O-ring rear and front body (pkge of 2) x1 2 W O-ring anode holder 2x1.5 1 W O-ring set (pkge of 8) 5.28x W PL 0333 EN

4 F-VB Spray Gun 2 Parts list -- F-VB complete -- (320000) fvb-parts1 Pos. esignation Qty Old Art. no. Art. no. 1 Electrode F Anode holder Rear securing ring Gas distribution ring Screw socket head cap Mx Insulating set screw M8x Fastener Mx Center body Rear body Screw fitting powder injector 3 mm Powder injector in conical support 2 see page 9 to Flat spring for 1 injector Flat spring for 2 injectors Socket head screw Mx12 for 1 injector flat spring for 2 injectors flat spring Injector mounting ring Plug nut (to close injector, if only one of two is used) Front lock ring Insulating intermediate body Cover O-Ring Nozzle with clamps 2x180 / / ø7mm (standard with delivery) For optional nozzles, see page 7 to PL 0333 EN 06

5 F-VB Spray Gun fvb-parts2 Pos. esignation Qty Old Art. no. Art. no. 25 O-ring electrode 12.2x O-ring nozzle front 29.87x O-ring nozzle rear 23.7x O-ring rear and front body (pkge of 2) x O-ring anode holder 2x O-ring 5.28x Options O-ring set includes O-ring electrode 12.2x O-ring nozzle front 29.87x O-ring nozzle rear 23.7x O-ring rear and front body (pkge of 2) x O-ring anode holder 2x O-ring 5.28x PL 0333 EN

6 F-VB Spray Gun 2.1 Tools for F-VB spray gun , 37, 38 3 fvb-tools Pos. esignation Qty Old Art. no. Art. no. -- F gun wood case Foam-rubber insert for wooden case O-ring grease Wrench 23x Spanner 12x Spanner 16x Spanner 11/16 x 13/ Adjustable wrench 150mm Hexagonal pin spanner 3,0 handle Screwdriver size Allen wrench size 1, Allen wrench size 3, Tweezers PL 0333 EN 06

7 F-VB Spray Gun 2.2 Nozzles and electrodes; complete sets for F-VB spray gun O-ring nozzle rear O-ring nozzle front Nozzle O-ring electrode f-vbset Electrode esignation Old Art. no. Art. no. Each set includes: Electrode O-ring electrode 12.2x O-ring nozzle front 29.87x O-ring nozzle rear 23.7x Nozzle (depending on nozzle bore diameter, position and number of injectors) PL 0333 EN

8 F-VB Spray Gun Version 1 - VPS nozzle for screw fitting powder injectors in general for coarse or difficult to melt powder efficient spray powder swirl into plasma stream shortened spray distance possible under standard chamber conditions limited range of the geometrical injection parameters (distance to the point of electrode, inlet angle) Ø Old Art. no. Art. no. 90 x 90 / Nozzle Set Nozzle Set Nozzle Set x 5 / 180 / Nozzle Set Nozzle Set Nozzle Set x 180 / Nozzle Set Nozzle Set Nozzle Set mm Powder injector, screw fitting M PL 0333 EN 06

9 F-VB Spray Gun Version 2 - VPS nozzle for injectors in conical support (secured with special holders and springs) in general for fine grained powder for plasma spraying without transferred arc minimal disturbance of the plasma stream centered powder injection longer spray distance under standard chamber conditions smaller plasma stream spray spot wide range of geometrical injection parameters (distance to point of electrode, inlet angle) higher kinetic energy of the powder particles in the pressure range of 0 to 80 mbar Ø Old Art. no. Art. no. 5 2 x 5 / 180 / mm Nozzle Set Nozzle Set Nozzle Set x 180 / mm Nozzle Set Nozzle (Standard) Set Nozzle Set x 5 / mm Nozzle Set Nozzle Set Nozzle Set / mm Nozzle Set Nozzle Set Nozzle Set Continued next page PL 0333 EN

10 F-VB Spray Gun Version 2 - VPS nozzle for injectors in conical support (secured with special holders and springs) Ø E Old Art. no. Art. no. 3 x 120 E = / 15 / 20 / 6.5 / 9 mm A E Nozzle Set Nozzle Set Nozzle Set C A B B E 6.5 Nozzle Set Nozzle Set Nozzle Set C E Nozzle Set Nozzle Set Nozzle Set x 90 / mm Nozzle Set Nozzle Set Nozzle Set mm Powder injector mm Powder injector mm Powder injector mm Powder injector mm Powder injector PL 0333 EN 06

11 F-VB Spray Gun Version 3 - VPS nozzle with tungsten pins for spraying with a transferred arc using injectors with the conical support (secured with special holders and springs) in general for fine grained powder for plasma spraying with-out transferred arc minimal disturbance of the plasma stream centered powder injection longer spray distance under standard chamber conditions smaller plasma stream spray spot wide range of geometrical injection parameters (distance to point of electrode, inlet angle) higher kinetic energy of the powder particles in the pressure range of 0 to 80 mbar 2 x 180 / mm Ø Old Art. no. Art. no. Nozzle Set Nozzle Set Nozzle Set tk ø20 -- Tungsten pin x 5 / mm Nozzle Set Nozzle Set Nozzle Set tk ø20 -- Tungsten pin Continued next page PL 0333 EN

12 F-VB Spray Gun 1 / mm Nozzle Set Nozzle Set Nozzle Set tk ø20 -- Tungsten pin mm Powder injector mm Powder injector mm Powder injector mm Powder injector mm Powder injector PL 0333 EN 06