Hill AFT/AirAFT Table

Transcription

1 Hill FT/irFT Table Owner s Manual 3 N. acton Hill Road, Frazer, P Fax Quality and Innovation Since 1945.

2 Congratulations! nd welcome to the Hill Laboratories family. Hill Laboratories Company has been making quality a family business since Your Hill FT Table is built in a tradition of innovation and value that Hill Laboratories products have become known for. Our good name rests on the confidence that your Hill Table will provide you with solid, reliable service for many years to come.

3 Index O On/Off Switch (See Power utton) P Paper Roll 4 Patient Switch (see Emergency Stop ) Power utton 4, 9, 11 Power Switch 4, 11 Pressure Pedal 2, 5, 6 Problems (See Trouble Shooting) R Raised Headpiece (See Headpieces) S Service and Support See intro, t Your Service Specifications 2 Speed Setting 8 Start utton 9 Stop utton 9 (lso see Emergency Stop ) T Table Components 4 Tension Control Knobs 2, 5, 6 Tiller ar 2, 7, 9 Timer 9 Thoracic reakaway 2, 5 Thoracic Drop (see Drops ) Thoracic Release 2, 5 Trouble Shooting 10, 11 W Warranty See intro, t Your Service Wiring Diagrams

4 Index ir-compressor 4 nkle Support - djusting 2, 8 - Harnesses 2, 8 rmrests 2 utomatic Flexion 8-9 uto Shutdown 4, 11 uto-touch Foot Pedal 4 asic Table Components 2 C Cervical Distraction (see Flexion ) 7 Cervical Flexion (see Flexion ) 7 Cleaning your Table 3 Cautions and Symbols 3 Control Panel - Main 2, 4, 5 - Flexion 2, 8, 9 D Diagrams (See Wiring Diagrams) Drops - Manual 5 - ir Drops 6 - Not popping up 10 E Electrical specifications 2 Electrical Schematics Emergency Stop - Patient Cut-Off Switch 9 F Flexion - uto Cervical 7 Flexion Control Panel 8 F (continued) Foot Pedal - uto-touch 4 - Corded 2, 4 - Rocker 2, 4 Foot Strips 2, 6 Function Control Panel (See Control Panel) G Gripper ars 2, 8 H Headpieces 2, 6, 7 - Dual-Drop 6 - Flexion 7 - Lateral djustment 7 - Raised 7 - Tilting 6 Height Pedal 4 Height Range 2 Horizontal Switch 9 K Knobs (See Tension Control Knobs) L Lateral djustment - Cervical 8 - Pelvic 8, 9 Lifting Capacity 2 Locking Mechanisms - Drops 6, 7 - Headpiece 6, 7 - Lateral Flexion 9 - Thoracic reakaway 5 - Thoracic Release 5 M Manual Drops (See Drops) N Not Working (See uto Shutdown) t Your Service The Hill Laboratories Guarantee. Your Hill Laboratories table has been thoroughly tested and inspected before shipment. ll parts are guaranteed against defect in materials for one full year from the date of purchase. During this period, any such defect will be remedied by Hill Laboratories or by a factory-authorized repair service at no charge. Tables damaged by mishandling or accident will be repaired at a reasonable charge. ll correspondence should be directed to your local dealer, or when this is not possible, to Hill Laboratories directly. We appreciate your business and your confidence in our products. Our aim is to provide you with excellent service and satisfaction for many years to come. Howard. Hill President, Hill Laboratories 15

5 Hill FT Manual Table of Contents Product Features asic Table Components 1.1 Specifications 1.2 Table Care Cleaning your Table 2.1 Caution and Symbol Explanation 2.2 asic Table Operation Preparing the FT for Your Patient 3.1 Height Pedal 3.2 Function Control Panel 3.3 Thoracic Release/Thoracic reakaway 3.4 Using Drops Manual Drops 4.1 ir Drops 4.2 Headpieces Tilting Headpiece 5.1 Dual Drop Headpiece 5.2 Raised Headpiece 5.3 Cervical Flexion Headpiece 5.4 Flexion and Lateral Movement Preparing for Flexion 6.1 Using Flexion 6.2 Using Lateral Movement 6.3 Wiring Diagram - FT, 24VDC, Part 3 Height System for all FT Models. Trouble Shooting Pages Wiring Diagrams Pages Index of Terms Pages

6 Wiring Diagram - FT, 24VDC, Part 2 ir System for all FT Models. Product Features asic Table Components 1. Tilting Headpiece. May include several options 2. Thoracic Drop with Thoracic Release/reakaway. 3. Lumbar Drop 4. Pelvic Drop on Flexion Section 5. Removable Pelvic Flexion Tiller ar 6. Slide-out nkle Support with nkle Harnesses 7. Flexion Control Panel 8. rmrest 9. djustable Patient Gripper ars 10. Power and ir-drop Control Panel (air-models) 11. Rocker Foot Pedal for Height djustment 12. Power Foot Strips for activating ir-drops (optional) 13. ir-pressure Foot Pedal (air-models) 14. Drop Tension Control Knobs 15. Tension Control Handle for Manual Spring-reakaway 16. Cocking Handle for Manual Drop 1.2 Specifications Electric requirement 60 Hz, 110 v~, 5 / irft - 10 (or cycle) Lifting capacity pounds crylic thermo-plastic base Ultra-Cell foam for comfort and shape retention Height Range - 211/2-29 or 221/2-30 Shipping weight approximately lbs. Length - 5' 5" (extends to 6'2" ), with cervical drop to 6 4 Standard width 24, optional

7 Table Care 2.1 Cleaning your Table Hill table upholstery may be cleaned with Hill Laboratories' Vinyl and Leather Cleaner or any household dishwashing liquid mixed with water. Hill also offers Protex Disinfectant Spray and wipes to protect against pathogens, such as MRS, HIV, Staph and the H1N1 Swine Flu Virus. Many stubborn stains can be removed by applying 91% rubbing alcohol (isopropyl alcohol) to the stain and wiping with a dry, soft, lint-free cotton cloth, towel or soft bristle brush. Wiring Diagram - FT, 24VDC, Part 1 ir System for all FT Models. Caution: These solvents are highly flammable; do not use near open flame or intense heat. Wear rubber gloves during all cleaning activities. When cleaning other parts of your table (besides upholstery) use only nonabrasive household detergents and water. 2.2 Caution and Symbol Explanation Caution: lways unplug the table before performing any maintenance. Caution: Check table once a year to make sure all internal and external bolts are secure. Caution: Table should be in its lowest height position when not attended. Caution: In case of power outage, the table will rely on the generator back-up of the facility where installed for powering to its lowest position. Caution: The power cord should be located to avoid risk of tripping or having objects rolled over or placed on top of it. Damaged cords should be replaced with another of hospital grade. Caution: Grounding reliability can only be achieved when connected to an equivalent receptacle marked hospital only or hospital grade. Symbols - Each of the symbols below are used in your table labeling. n explanation of each is below. ~ Dangerous Voltage Type F pplied Ground Symbol Part Symbol Symbol ttention Symbol consult accompanying documents lternating Current Symbol Don t Touch Symbol 3 12

8 Problem The main power board is turning off on it s own. This is likely the uto-shutdown mode operating normally. When the FT is left inactive for 2 hours, the uto-shutdown mode will power the main control board down automatically. To Fix: Simply press the green power button. asic Table Operation 3.1 Preparing the FT for your patient Plug your table into any 110 volt grounded outlet or 220 volt grounded outlet when specified. The Power Switch is located where the power cord exits the table (photo 1). It ships in the OFF position. fter the table is plugged in, press the button in to turn the power on. Paper Roll - Used for facedown treatment. Close the paper cutter located on the side of the headpiece (photo 2) and tear off excess. photo 1 Plug in, then push in to turn ON photo 2 Problem Power Outage: Due to lightning or some other reason, you facility may lose electrical power from time to time. When this happens, your table s power switch will need to be reset. Plug in, then push in to turn ON To Fix: Unplug the table from the wall outlet and wait approximately 30 seconds. Plug the table back in to the outlet and then press the power switch in, (see photo), to the ON position Preparing the ir System For air models, press the Power button of the main Control Panel (photo 3) to start the table s air-compressor. Each of the fuction buttons will light consecutively and then turn off. The compressor will stop when the pressure reaches 90 lbs. See 4.2, Using photo 3 ir-drops for air-feature instructions. Note: The FT is equipped with an uto Shutdown mode which will power down the main control board if the table is inactive for 2 hours. Press the green power button to power the board back up. 3.2 Height Pedal The basic FT is equipped with a dual Rocker Foot Pedal (#11 under Product Features ) which controls the table height from either side of the base. Press the right side of the pedal to elevate; the left side to lower. uto-touch Foot Pedal (Option) The uto-touch Foot Pedal option maintains upward or downward motion even after releasing the pedal. To operate: - With the table at the lowest height, double-touch the UP arrow and release. The table will continue upward until you tap either side of the pedal again. - With the table at the highest height, double-touch the DOWN arrow and release. The table will continue downward until you tap either side of the pedal again. - With the table at any starting height in between, a single-touch up or down will start and stop the motion. 11 4

9 3.3 Function Control Panel For FTs equipped with air functions, the control panel (photo 3) has a power button, drop-selector buttons and a thoracic-breakaway button. fter power, press in any order to activate the corresponding function. 3.4 Thoracic Release / Thoracic reakaway Thoracic Release To operate the Thoracic Release, pull the switch towards you while holding the cushion; adjust to the desired depth and release the switch to lock the cushion. Thoracic Spring-reakaway The standard Thoracic reakaway (non-air) uses a fixed-tension gas shock to create a recoil movement when the thoracic cushion is unlocked (see photo 4). photo 4 Unlock Lock Thoracic ir-reakaway For tables with a Thoracic ir-reakaway, it is necessary to regulate the airpressure before treating your patient. Follow these steps: Trouble Shooting Problem The Pelvic Cushion cocks up but does not stay up. The drop pin has come out of it s track. To Fix: 1. Loosen the Pelvic Drop Tension Knob enough to rotate the drop pin (see in drawing) so that the cross pin () faces and engages the bracket (C) as shown in the photo and drawing below. You may need to use a flat head screw driver to turn the pin from the bottom. Once the pin is turned into the bracket, retighten the Tension Knob. C C 1. Select the THOR (thoracic) button on the main control panel (photo 3). 2. Unlock the thoracic breakaway switch by pulling toward you until it clicks (photo 4). This will allow the cushion to move freely up and down. 3. Press the right side of the Pressure Pedal (#13, page 2) to increase the air-pressure in the thoracic section. Push down on the cushion as you add air to test for desired firmness. 4. Lock the cushion at any point by pushing the thoracic lock switch towards the table until it clicks. e sure to depressurize the thoracic section after locking to prevent an abrupt release when unlocked. Using Drops 4.1 Manual-Drops Cocking handles are located on both sides of each drop. Push the cocking handle up (, 5) to activate the drop. Turn the tension knobs () clockwise to tighten and counterclockwise to loosen (also see caution, pg. 6). photo 5 Problem The Cervical Cushion cocks up but does not stay up. The drop pin has come out of it s L-bracket. To Fix: 1. Loosen the Cervical Drop Tension Knob enough to rotate the drop pin (see in photo) so that the spring pin () faces and engages the bracket (C) as shown in the photo. Once the pin is turned into the bracket, retighten the Tension Knob. C 5 10

10 Horizontal Switch - The Horizontal Switch contols how the table behaves when the Stop utton is pushed. If you want the table to cycle back to the horizontal position when the Stop utton is pushed, set the Horizontal Switch to ON. If you want the table to stop immediately at any point in the flexion cycle when the Stop utton is pushed, set the Horizontal Switch to OFF. Start utton - Push to start the flexion treatment. Stop utton - Push to stop the flexion treatment. Important: See Horizontal Switch (above) for setting Stop utton behavior. Timer - For tables equipped with a timer, flexion can be set to run automatically for up to 30 minutes (photo 17). Patient Cut-Off Switch The patient can stop treatment immediately at anytime using the Patient Cut-Off Switch. The PCO switch is located on the left armrest support (photo 18). Instruct the patient as to photo 18 photo 19 photo 20 photo 17 the location and function of the switch. To resume treatment after stopping, press the green Start utton on the flexion control panel. 6.3 Using Lateral Motion To use Lateral Motion with flexion, insert the flexion handle (tiller) into the receptacle, just above the ankle cushion (photo 19). Disengage the lateral lock handle counter-clockwise (photo 20). This will allow the lower part of the table to move freely from side-to-side. You can also lock the cushion laterally at any point on either side by turning the lock to the 6 o clock position. lso, be sure the handle is locked before patient exits the table. 4.2 ir-drops Drop Selector Switches The Drop Selector Switches (photo 6) activate the table drops. You may choose one or up to four drops simultaneously. Once selected, press the Pressure Pedal (or optional foot strips, #12, pg. 2) to activate the drops. fter discharging, press the pedal or foot strip again to immediately reactivate the drops. Drop Tension Control Knobs The Drop Tension Knobs are located on the left side of each drop (#14, pg. 2). Turn the knob clockwise to increase the firmness of the drop counter clockwise to decrese. Caution: Do not loosen Tension Knobs too far- djusting the tension knobs out too far can cause the cervical and pelvic drops to malfunction. See Trouble Shooting section on pg. 10 for more detail. Headpieces 5.1 Tilting Headpiece ll FT models are equipped with a tilting headpiece. The lever for tilting is located under the front of the headpiece (, photo 7). It controls the angle of tilt 30 positive or negative. Click the switch in to lock; out to unlock. 5.2 Dual-Drop Headpiece photo 6 Photo 7 The Dual-Drop headpiece contains two drops a drop-forward motion and a straight-down drop. Important Note: efore changing any of the settings described in the following section, be sure the headpiece drop is discharged. C 9 6

11 Straight-Down Drop Headpiece To use the Straight-Down Drop of the headpiece, the setting lever should remain in the side channel of the setting mechanism as shown in photo 8. e sure that the pin locks into the receiver behind it otherwise, the drop will not work. For a manual drop, push up on the black cocking handle to engage. For ir- Cervical Drop, see section 4.2. Drop-Forward Motion Headpiece To use the Drop-Forward Motion action of the headpiece, pull the black setting lever out and turn it to the left so that it points straight down (photo 9). For a manual drop, push up on the black cocking handle to engage. For ir-cervical Drop, see section 4.2). 5.3 Raised Headpiece The Raised Headpiece allows the headpiece to rise up to 5 above the surface of the table. It is controlled by a lever in front of the head cushion (7, ). Pull and hold the switch to adjust to the desired height; release to lock. To lower, apply gentle downward pressure to the back side of the headpiece with one hand while pulling the lever to adjust. 5.4 Cervical Flexion Headpiece The Cervical Flexion Headpiece includes the raised headpiece feature, occipital strap and the removable tiller bar. Set Up Position the patient as shown in photo 10. Secure the occipital strap using the Velcro connectors. photo 12 photo 8 photo 9 photo 10 photo 11 Important: Prior to flexion, release the red cushion lock pin by pulling and turning the lever to the left (photo 11). This will allow the cushion to slide in the axial direction for applying manual cervical distraction. Lateral djustment The Cervical Flexion Headpiece includes lateral motion. To use lateral motion, locate the switch as shown in photo 12 (7, C). Pull the lever toward you to click and unlock. This will allow full-range lateral movement. The headpiece can also be locked at any angle in the lateral range. Flexion and Lateral Movement 6.1 Preparing for Flexion pplying flexion with the Hill FT is easy. Follow these steps - Set Up Position the patient comfortably on the table in the face-down position. djust the slide-out ankle support to fit your patient s height using the lever located under the ankle cushion (photo 13). Secure the ankles by firmly fastening the straps with the velcro connectors (photo 14). Now, have your patient grasp the gripper bars (photo 15). The length of the bars can be adjusted by loosening the handle (, 15) and sliding the bars so that the patient can grasp them firmly. Tighten the handles on each bar to secure. The Gripper ars keep the patient from sliding during flexion treatment. photo 14 photo Using Flexion Using the Flexion Control Panel ll of the controls for flexion are conveniently located at the foot end of the FT (see 8, under Product Features ). Speed Setting - The uto Flex has a fixed rate of movement from 1-28 cycles per minute (photo 16). Set to desired speed and press Start (always start with a low speed if there is any concern about a patient s flexibility). Speed can be changed at any time during the cycle. photo 16 Photo