Instructions. Lunette Wrench Set

Transcription

1 Instructions Lunette Wrench Set Instructions Lunette Wrench Set The Lunette wrench Set consists of the lunette wrench, a workbench, a pin and an O-ring, as well as a battery. This wrench allows you to replace the battery of a Suunto Stinger or a Spyder in a simple do-it-yourself process. The included workbench greatly facilitates the process of replacing the battery. Place your diving computer between the 4 metal pins as depicted in the bottom illustration (photograph). This will ensure that the computer remains securely fastened in place, thus allowing you to unscrew the crown with the special wrench. Replace the old battery and the O-ring with the new ones, and use the wrench again to screw the crown back on. Important! Make sure to work very carefully (and in a calm environment) on a clean work surface. Use pin as assembly tool. 1

2 1.0 Place clock on workbench (90 to workbench) 2.0 Place wrench onto lunette. (cogs must grip, level) 2

3 2.1 Turn wrench to the left (lunette fits very tight) 2.2 Unscrew lunette by hand. 3

4 2.3 Place lunette aside 3.0 Use pin to lift the glass on the side containing the small notch. 4

5 3.1 Place glass aside 4.0 Lift synthetic ring with the pin. 5

6 4.1 Place synthetic ring aside. 5.0 Lift O-ring with the pin. 6

7 5.1 Remove and discard the O-ring (NOT intended for re-use). 6.0 Carefully extract clock element (ease element out by holding on at the top and the bottom!) 7

8 6.1 Remove clock element (watch out for the wire) und place it upside down into the casing. 7.0 Lift battery clamp (star) by the protruding point. 8

9 7.1 Place battery clamp (star) aside. 8.0 Remove battery (carefully extracting it with the pin) and properly dispose of the battery. 9

10 8.1 Do not throw battery into trash; use public collection facilities for hazardous materials. 8.2 Insert new battery. 10

11 9.0 Place battery clamp back on unit (hooking in the left side first). 9.1 Place battery clamp back on unit (pushing right side down with pin). 11

12 10.0 Turn clock element back around (watch out for the wire) and insert Press clock element into casing (don t push on the display only on the edge). 12

13 10.2 Press clock element into casing (don t push on the display only on the edge) Insert new O-ring exactly into the surrounding groove. (The O-ring must be free of grease!) 13

14 12.0 Place synthetic ring back on unit (check the fit of the O-ring) Put glass back on unit (with the larger surface facing downward). Clean glass prior to this to avoid fingerprints on the glass. 14

15 14.0 Place lunette back on unit (check for level fit) Wind lunette forward by hand (check for level fit). 15

16 14.2 Place wrench onto lunette (Mesh must grip, be level) Tightly fasten lunette with lunette wrench. 16

17 Inhaltsverzeichnis 1.0 Place clock on workbench (90 to workbench) Place wrench onto lunette. (cogs must grip, level) Turn wrench to the left (lunette fits very tight) Unscrew lunette by hand Place lunette aside Use pin to lift the glass on the side containing the small notch Place glass aside Lift synthetic ring with the pin Place synthetic ring aside Lift O-ring with the pin Remove and discard the O-ring (NOT intended for re-use) Carefully extract clock element (ease element out by holding on at the top and the bottom!) Remove clock element (watch out for the wire) und place it upside down into the casing Lift battery clamp (star) by the protruding point Place battery clamp (star) aside Remove battery (carefully extracting it with the pin) and properly dispose of the battery Do not throw battery into trash; use public collection facilities for hazardous materials Insert new battery Place battery clamp back on unit (hooking in the left side first) Place battery clamp back on unit (pushing right side down with pin) Turn clock element back around (watch out for the wire) and insert Press clock element into casing (don t push on the display only on the edge) Press clock element into casing (don t push on the display only on the edge) Insert new O-ring exactly into the surrounding groove. (The O-ring must be free of grease!) Place synthetic ring back on unit (check the fit of the O-ring) Put glass back on unit (with the larger surface facing downward). Clean glass prior to this to avoid fingerprints on the glass Place lunette back on unit (check for level fit) Wind lunette forward by hand (check for level fit) Place wrench onto lunette (Mesh must grip, be level) Tightly fasten lunette with lunette wrench

18 Publisher Technisches Büro Kühnhold Ehestorfer Weg Hamburg Germany Copyright Copyright and labeling Disclaimer Recycling All images and text in this instruction manual, as well as the instruction manual itself are copyright protected, any further use must be approved in writing by All brands and trademarks specified within the description and, where applicable, protected by a third party are subject without restriction to the terms and conditions of the respectively valid right to use a symbol and the ownership rights of each registered owner. The mere mention thereof shall not be construed to represent that the trademarks are not protected by third party rights! The brand names and trademarks used in this documentation are the property of the respective rights owners and are used here only for descriptive purposes. Opening the dive computer and replacing the battery shall be at your own risk! No liability shall be assumed for lack of waterproofness or damage. European Union Disposal information: This symbol indicates that this product must be disposed of pursuant the valid legal provisions and separated from domestic waste. Bring this product to an official collection point for disposal. Products can be brought to some collection points for disposal free of charge. Separate collection and recycling conserves raw material reserves and ensures compliance with all regulations for the protection of health and the environment when recycling the product. WEEE-Reg.-Nr. DE