Fault Code 34 - Weak Battery Voltage Supply
|
|
- August Newton
- 5 years ago
- Views:
Transcription
1 Fault Code 34 - Weak Battery Voltage Supply Fault Isolation Procedures TRTS0930 Fault Code 34 - Weak Battery Voltage Supply J1587: MID 130 PID 168 FMI 14 J1939: SA 3 SPN 168 FMI 14 Overview This fault indicates the vehicle is supplying weak battery voltage to the transmission for 10 seconds. When troubleshooting an Inactive code See Product Diagnostic (PD) Mode on page 11. Detection Starting at key-on and throughout operation, the Transmission Electronic Control Unit (TECU) constantly measures vehicle voltage. If voltage is below 9 volts for more than 10 seconds, Fault Code 34 will be set. The service light will not flash. Fallback If this fault occures while moving, it causes a 1-speed fallback. Once the vehicle is stopped, the starting gear and reverse can be engaged Possible Causes This fault code can be caused by any of the following: Corroded or loose power supply to TECU Low batteries Damaged Vehicle Harness TECU Charging system Eaton. All rights reserved
2 TRTS0930 Fault Isolation Procedures Fault Code 34 - Weak Battery Voltage Supply Component Identification Vehicle Charging System Batteries Eaton. All rights reserved 119
3 V COM A Fault Code 34 - Weak Battery Voltage Supply Fault Isolation Procedures TRTS0930 Fault Code 34 - Weak Battery Voltage Supply A Purpose: Measure battery voltage. Visually inspect batteries, inline fuse, power and ground supplies to TECU. B Purpose: Verify proper ground path at 4-way diagnostic port. 1. Key off. 2. Inspect starter/battery and in-line fuse holder connections for integrity. 3. Measure voltage across batteries. If voltage is 11 to 13 volts on a 12-volt system or 22 to 26 on a 24-volt system, proceed with battery load test. Repair or replace batteries as required. Go to Step B. If voltage is outside of range, repair or replace batteries, charging system as required. Repeat this step. 1. Locate diagnostic port on Transmission Harness. 2. Key on. 3. Measure voltage between Pin C and the battery negative post. Warning! - Do Not Load Test at Diagnostic Port 4-Pin Diagnostics Port B C A D VOLTS Battery Negative Post 4-way 4-Pin Diagnostic Port (Located at the left rear corner of the transmission.) B - Service Bat. + C - Service Bat. - A - Service Ignition + If voltage between is 0.70 volts or less, go to Step C. If voltage is outside of range, repair battery ground supply to TECU. Repeat test Eaton. All rights reserved
4 TRTS0930 Fault Isolation Procedures Fault Code 34 - Weak Battery Voltage Supply C Purpose: Measure battery voltage at 4-way diagnostic port. D Purpose: Measure ignition voltage at 4-way diagnostic port. 1. Locate diagnostic port on Transmission Harness. 2. Key on. 3. Measure voltage between Pin B and Pin C. 1. Key on. 2. Measure voltage between Pin A and Pin C. Warning! - Do Not Load Test at Diagnostic Port 4-Pin Diagnostics Port Warning! - Do Not Load Test at Diagnostic Port 4-Pin Diagnostics Port B A C D B C A D 4-way 4-Pin Diagnostic Port (Located at the left rear corner of the transmission.) 4-way B - Service Bat. + C - Service Bat. - A - Service Ignition + If voltage is within 0.6 volts of battery voltage, go to Step D. If voltage is outside of range, repair battery power supply to TECU. Fuse may be blown. Repeat test. 4-Pin Diagnostic Port (Located at the left rear corner of the transmission.) B - Service Bat. + C - Service Bat. - A - Service Ignition + If voltage is within 0.6 volts of battery voltage, go to Step E. If voltage is outside of range, repair ignition power supply to TECU. Fuse may be blown. Repeat test Eaton. All rights reserved 121
5 Fault Code 34 - Weak Battery Voltage Supply Fault Isolation Procedures TRTS0930 E Purpose: Check for active and Inactive fault codes. 1. Key on. 2. Retrieve codes. See Fault Code Retrieval/Clearing on page 5. If Fault Code 34 is Active, replace the: - Medium-Duty Transmission Electronic Control Unit (TECU) - Heavy-Duty Transmission Electronic Control Unit (TECU) Go to Step V. If Fault Code 34 is Inactive, clear codes. Go to Step V. V Purpose: Verify repair. 1. Key off. 2. Key on. 3. Clear codes. See Fault Code Retrieval/Clearing on page Reconnect all connectors and the negative battery cable. 5. Drive vehicle and attempt to reset the code 6. Check for codes. See Fault Code Retrieval/Clearing on page 5. If no codes, test complete. If Fault Code 34 appears go to Step A. to find error in testing. If code other than 34 appears, See Fault Code Isolation Procedure Index on page Eaton. All rights reserved
6 TRTS0930 Fault Isolation Procedures Fault Code 34 - Weak Battery Voltage Supply Eaton. All rights reserved 123
Fault Code 16: Eaton Proprietary Link (EPL)
ault ode 16: aton Proprietary Link (PL) ault Isolation Procedure ault ode 16: aton Proprietary Link (PL) 1587:MI 130 SI 248 MI 2 Overview ault ode 16 indicates the Shift ontroller and the Transmission
More informationRWRG Fault Code 61 Pre-Authorization
RWRG0077 - Fault Code 61 Pre-uthorization Overview The UltraShift PLUS Transmission is equipped with an X-Y Shifter that selects a transmission gear. The X-Y Shifter motors are controlled with electrical
More informationRWRG Main Shaft Speed Sensor Pre-Authorization
RWRG0076 - Main Shaft Speed Sensor Pre-Authorization Overview The UltraShift PLUS and Fuller Advantage transmissions are equipped with four electronic speed sensors. The Input Shaft, Main Shaft and Output
More informationBendix BlindSpotter Collision Warning System. Troubleshooting Guide
Bendix BlindSpotter Collision Warning System Troubleshooting Guide Bendix BlindSpotter Collision Warning System BW860 (Formerly VOTS003) September 0 General Information General Warnings Before starting
More informationRWRG Fault Code 71 Pre-Authorization
RWRG0080 - Fault Code 71 Pre-Authorization Overview The UltraShift PLUS transmission uses the X-Y Shifter to engage and disengage a gear based on the driver s selected mode of operation. Gear disengagement
More informationFAULT CODE 451 Injector Metering Rail Number 1 Pressure Sensor Circuit - Voltage Above Normal or Shorted to High Source
Page 1 of 16 FAULT CODE 451 Injector Metering Rail Number 1 Pressure Sensor Circuit - Voltage Above Normal or Shorted to High Source View Related Topic Overview CODE REASON EFFECT Fault Code: 451 PID:
More informationFAULT CODE 692 Turbocharger Number 1 Compressor Inlet Temperature Sensor Circuit - Voltage Below Normal or Shorted to Low Source
Page 1 of 14 FAULT CODE Turbocharger Number 1 Compressor Inlet Temperature Sensor Circuit - Voltage Below Normal or Shorted to Low Source View Related Topic Overview CODE REASON EFFECT : PID: SPN: 1172
More informationCUMMINS FAULT CODE: 1239 PID: SPN: 2623 FMI: 3/3 LAMP: AMBER
CUMMINS ACCELERATOR PEDAL OR LEVER POSITION SENSOR 2 CIRCUIT - VOLTAGE ABOVE NORMAL OR HORTED TO HIGH SOURCE FAULT CODE: 1239 PID: SPN: 2623 FMI: 3/3 LAMP: AMBER DESCRIPTION ISX and ISM Accelerator Pedal
More informationNUMBER: 08 DDEC VI 16 S.M. REF.: listed in Table 1 ENGINE: DD15 DATE: April 2008 SUBJECT: SPN 1636 AND SPN 2630 PUBLICATION: DDC-SVC-MAN-0029
NUMBER: 08 DDEC VI 16 S.M. REF.: listed in Table 1 ENGINE: DD15 DATE: April 2008 SUBJECT: SPN 1636 AND SPN 2630 PUBLICATION: DDC-SVC-MAN-0029 The procedure and direction for SPN 1636 have changed. SPN
More informationFuller Heavy Duty Transmissions TRTS0020 EN-US October 2007
Troubleshooting Guide Fuller Heavy Duty Transmissions TRTS0020 EN-US October 2007 RT-11109-T RT-11109-TR RT-11109-TS RT-12109-T RT-14109-TS RTO-11109-T RTO-11109-TS RTO-11109-T RTO-11109-TE RTO-11109-TR
More informationAlternator Ground Check Verify Repairs
DDEC III/IV SINGLE ECM TROUBLESHOOTING GUIDE 16.3.6 Alternator Ground Check Perform the following steps to check the alternator ground. 1. Connect all connectors. 2. Remove alternator belt or disable alternator
More informationAdditions, Revisions, or Updates
1 4 09-14 SUBJECT DATE ACM2.1 SPN 3597/FMI 3, 4 - GHG14 April 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN 3597/FMI 3,
More informationNUMBER: 1 DDEC VI 07 S.M. REF.: Listed in Table 1 ENGINE: Series 60 DATE: February 2007
NUMBER: 1 DDEC VI 07 S.M. REF.: Listed in Table 1 ENGINE: Series 60 DATE: February 2007 SUBJECT: SENSOR RESISTANCE CHART PUBLICATION: 6SE567 The Series 60 DDEC VI Troubleshooting Guide has been revised.
More informationInstallation and Service Manual M² Sync Room Slideout System without Room Lock Connectors on Control Box
Installation & Service Manual M² Sync Room Slideout System w/o Room Locks: for Slideout Control Box# 1510000143 and 1510000198 Figure 1 01/13 Power Gear #3010002088 Rev. 0C Installation and Service Manual
More informationG.M. Electronic 4x4 System
154 Diagnosis The NV233 systems up to 2004, found on Blazer, S-10 trucks and Tahoe applications, will not allow data or code retrieval with a scanner, however manual code retrieval is available. To retrieve
More informationSPN 51 or Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description
SPN 51 or 3673 Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description SPN FMI Description Possible Causes 51 3 TPS1 Sensor Signal Voltage High Open/high resistance in low Short to
More information34 FLASH CODE 34 - TBS LOW
34 FLASH CODE 34 - TBS LOW Section Page 34.1 DESCRIPTION OF FLASH CODE 34... 34-3 34.2 SAE J1587 EQUIVALENT CODE FOR FLASH CODE 34... 34-3 34.3 TROUBLESHOOTING FLASH CODE 34... 34-4 Figure 34-1 Turbo Boost
More informationInstallation & Service Manual
Installation & Service Manual for M² Sync Slideout Control Box #1510000122 CONTENTS Introduction Installation Installation Problems Program Mode Operation Mode Preventative Maintenance Fault Diagnostics
More information33 FLASH CODE 33 - TBS HIGH
33 FLASH CODE 33 - TBS HIGH Section Page 33.1 DESCRIPTION OF FLASH CODE 33... 33-3 33.2 SAE J1587 EQUIVALENT CODE FOR FLASH CODE 33... 33-3 33.3 TROUBLESHOOTING FLASH CODE 33... 33-4 Figure 33-1 Turbo
More informationDR: Camshaft Position (CMP) Sensor
2007 PCED On Board Diagnostics SECTION 5: Pinpoint Tests Procedure revision date: 03/29/2006 DR: Camshaft Position () Sensor DR: Introduction DR1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) Are DTCs P0340,
More information41 FLASH CODE 41 - TOO MANY SRS
41 FLASH CODE 41 - TOO MANY SRS Section Page 41.1 DESCRIPTION OF FLASH CODE 41... 41-3 41.2 SAE J1587 EQUIVALENT CODE FOR FLASH CODE 41... 41-3 41.3 TROUBLESHOOTING FLASH CODE 41... 41-4 41-2 From Bulletin
More informationTroubleshooting Guide
Bendix VORAD VS-400 Radar System Troubleshooting Guide Bendix VORAD Collision Warning System Bendix SmartCruise Adaptive Cruise Control Bendix BlindSpotter Side Object Detection BW2771 (Formerly VOTS0100)
More informationFAULT CODE 474. Starter Solenoid Lockout Relay Driver Circuit
Page 1 of 12 Overview FAULT CODE 474 Starter Solenoid Lockout Relay Driver Circuit CODE REASON EFFECT Fault Code: 474 PID: S052 SPN: 1321 FMI: 2 LAMP: Yellow SRT: Either low voltage detected when 12 VDC
More informationThe Aftertreatment System Technician's Guide (7SE63) was revised to include three new procedures.
NUMBER: 07 ATS 3 S.M. REF.: Listed in Table 1 ENGINE: ATS DATE: December 2007 SUBJECT: ADDITIONAL PROCEDURES WERE ADDED TO AFTERTREATMENT SYSTEM PUBLICATION: 7SE63 The Aftertreatment System Technician's
More informationDA: Intake Air Temperature (IAT) Sensor
2007 PCED On Board Diagnostics SECTION 5: Pinpoint Tests Procedure revision date: 03/29/2006 DA: Intake Air Temperature () Sensor DA: Introduction DA1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) Are DTCs
More informationIntake Air Temperature 2 (IAT2 ) Sensor
Page 1 of 6 Year = 2011 Model = Mustang Engine = 5.0L VIN = IDS Version = t Available Intake Air Temperature 2 ( ) Sensor This pinpoint test is intended to diagnose the following: sensor (12A697) harness
More informationAdditions, Revisions, or Updates
1 3 30-12 SUBJECT DATE SPN 1761/FMI 2, 9 - MY13 March 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 MY13 DD Platform SPN 1761/FMI 2 - MY13
More informationParking Brake Indicator Is Flashing
Page 1 of 5 Troubleshooting 247B, 257B, 267B, 277B and 287B Multi Terrain Loaders and 216B, 226B, 232B, 236B, 242B, 246B, 248B, 252B, 262B and 268B Skid Steer Loaders Interlock Electronic Control System
More informationO2 Sensor Testing. If your engine has unexpectedly started to run poorly, an O2 Sensor Test should be performed.
O2 Sensor Testing If your engine has unexpectedly started to run poorly, an O2 Sensor Test should be performed. IMPORTANT: Testing the O2 sensors using the procedures below REQUIRES that the engine will
More information1999 Mercury Cougar ACCESSORIES & EQUIPMENT' 'Passive Anti-Theft Systems - Cougar 1999 ACCESSORIES & EQUIPMENT
DESCRIPTION 1999 ACCESSORIES & EQUIPMENT Passive Anti-Theft Systems - Cougar Passive Anti-Theft System (PATS) is available on some vehicles. The system is passive in that it does not require any activity
More informationDS: Air Conditioning Pressure (ACP) Transducer Sensor
2009 PCED Gasoline Engines SECTION 5: Pinpoint Tests Procedure revision date: 08/12/2009 DS: Air Conditioning Pressure () Transducer Sensor DS: Introduction DS1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS)
More informationME: Fuel Pump Control - High Pressure Fuel Injection Pump
Page 1 of 6 2008 Ford F-250 Super Duty : Diagnostics > 6.4L Diesel > Pinpoint Tests > ME: Fuel Pump Control - High Pressure Fuel Injection Pump ME: Fuel Pump Control - High Pressure Fuel Injection Pump
More informationAdditions, Revisions, or Updates
1 SUBJECT DATE SPN 3250/FMI 0, 15 - EPA10 October 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3250/FMI 0 - DDC-SVC-MAN-0084 EPA10 DD Platform EPA10
More informationPage 1 of 7 2004 PCED Gasoline Engines SECTION 5: Pinpoint Tests Procedure revision date: 05/08/2007 DM: Manifold Absolute Pressure () and Thermal Manifold Absolute Pressure (T) Sensor DM: Introduction
More informationInstallation and Service Manual M² Sync Room Slideout System without Room Lock Connectors on Control Box
Installation & Service Manual M² Sync Room Slideout System w/o Room Locks: for Slideout Control Box# 1510000143 and 1510000198 Figure 1 01/13 Power Gear #3010002088 Rev. 0C Installation and Service Manual
More informationFAULT CODE 131 (IVS) Accelerator Position Sensor Circuit
FAULT CODE 131 (IVS) Accelerator Position Sensor Circuit Overview CODE REASON EFFECT Fault Code: 131 PID: P091 SPN: 91 FMI: 3 LAMP: Red SRT: 00-084 High voltage detected at accelerator position signal
More informationNotice Added to Sections Listed Below February Removal of the Bypass Valve. Removal of the Pressure Relief Valve
2 15-12 1 2 15-12 SUBJECT DATE Notice Added to Sections Listed Below February 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0082 Removal of
More informationEBP Sensor (Exhaust Back Pressure)
Page 1 of 8 EBP Sensor (Exhaust Back Pressure) DTC SPN FMI Condition 3341 1209 4 EBP signal out-of-range LOW 3342 1209 3 EBP signal out-of-range HIGH Page 2 of 8 Function diagram for the EBP sensor The
More informationFile: 12-fc131 Page 1 of 11. Fault Code 131 CODES REASON EFFECT
File: 12-fc131 Page 1 of 11 Fault Code 131 Accelerator Pedal or Lever Position Sensor Circuit - Voltage Above Normal, or Shorted to High Source CODES REASON EFFECT Fault Code: 131 PID(P), SID(S): P091
More informationDX: Engine Coolant Temperature (ECT) Sensor
2009 PCED Gasoline Engines SECTION 5: Pinpoint Tests Procedure revision date: 12/10/2008 DX: Engine Coolant Temperature (ECT) Sensor DX: Introduction DX1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) Are DTCs
More informationAdditions, Revisions, or Updates
1 10 16-13 SUBJECT DATE SPN 3216/FMI 13 - EPA10/GHG14 October 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 EPA10 GHG14 DD Platform SPN
More informationPage 1 of 5 Pinpoint Test M: DTCs B1407:11, B1407:12, B1407:13 and B1407:1A Diagnostic Overview Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
More informationFAULT CODE 432 (SSS) Accelerator Pedal Circuit
FAULT CODE 432 (SSS) Accelerator Pedal Circuit Overview CODE REASON EFFECT Fault Code: 432 PID: P091 SPN: 91 FMI: 13 LAMP: Red SRT: 00-612 No voltage detected at idle validation on-idle signal pin 6 of
More informationVariable Geometry Turbocharger (VGT) Actuator Connector
Page 1 of 5 Year = 2006 Model = F-Super Duty Engine = VIN = IDS Version = 77A.05 (IDS-77A.05) Variable Geometry Turbocharger (VGT) Output Circuit Function The VGT actuator is a variable position valve
More informationSECTION Multifunction Electronic Modules
419-10-i Multifunction Electronic Modules 419-10-i SECTION 419-10 Multifunction Electronic Modules CONTENTS PAGE DIAGNOSIS AND TESTING Smart Junction Box (SJB)... 419-10-2 Principles of Operation... 419-10-2
More informationService Manual for Battery Control Center
Service Manual for Battery Control Center P/N 82 E0071 00 (Ref. 81 1317) June, 1999 Battery Control Box Operation Charging Circuit This function charges the coach battery from the engine alternator while
More informationTechnical Information and Diagnostic Guide
Technical Information and Diagnostic Guide This guide will assist you in becoming more familiar with the working components of the NITE System and the proper steps and procedures to completely diagnose
More informationPage 1 of 6 1Search Print Date: B3140 Power Door Lock Switch Malfunction - DTC B3140, B3145, B3150, Or B3155 Diagnostic Instructions Perform the Diagnostic System Check - Vehicle prior to using this diagnostic
More informationSECOND GENERATION Use this guide with unit serial number prefix beginning with BWF using Terra Power separator.
Technical Information and Diagnostic Guide for SECOND GENERATION Use this guide with unit serial number prefix beginning with BWF using Terra Power separator. This guide will assist you in becoming more
More informationSPN 3227 or Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description
SPN 3227 or 3266 Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description SPN FMI Description Possible Causes 3227 4 EGO Bank A Sensor 2 Open or short to ground on Voltage Low signal
More information1995 Lincoln Town Car Cartier. AIR BAG RESTRAINT SYSTEM 1996 ACCESSORIES/SAFETY EQUIPMENT Ford Motor Co. Air Bag Restraint System
DIAGNOSIS & TESTING SELF-DIAGNOSTICS The air bag diagnostic monitor lights the AIR BAG warning light for about six seconds when the ignition is turned to RUN and then turns the AIR BAG warning light off.
More information4. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
Published: Dec 17, 2007 Instrument Cluster Overview Data is provided to the instrument cluster from other subsystem modules in the form of controller area network (CAN) s. The instrument cluster identifies
More informationFuel Pump (FP ) Relay
Page 1 of 12 Year = 2007 Model = F-150 Engine = VIN = IDS Version = t Available Fuel Pump (FP ) Relay This pinpoint test is intended to diagnose the following: fuel pump relay (9345) inertia fuel shutoff
More informationPage 1 of 29 Section 04-05: Suspension, Computer Controlled 1997 Town Car Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 05/16/2000 Suspension, Computer Controlled Inspection and Verification
More information1999 Toyota RAV ACCESSORIES & EQUIPMENT Cruise Control Systems - RAV4
1999 ACCESSORIES & EQUIPMENT Cruise Control Systems - RAV4 DESCRIPTION WARNING: Deactivate air bag system before performing any service operation. See AIR BAG RESTRAINT SYSTEMS article. DO NOT apply electrical
More informationWiring diagrams on page 29 are for reference only. For detailed vehicle wiring refer to Navistar documents.
1 10/2014 REV 7 !!Attention!! Before performing diagnostics: Wiring diagrams on page 29 are for reference only. For detailed vehicle wiring refer to Navistar documents. Check for Fault Codes using the
More informationhttps://w05.dealerconnect.chrysler.com/service/mds2002/common/jsp/xml.jsp?xmlurl=... P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW
Page 1 of 10 P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW Page 2 of 10 For a complete wiring diagram Refer to the Wiring Information. Page 3 of 10 When Monitored: While the engine is running. Set Condition:
More informationAdditions, Revisions, or Updates
1 01 11-16 SUBJECT DATE SPN 647 (MCM)(EPA07-EPA10-GHG14) January 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DDC-SVC-MAN-S084 DD Platform
More informationSPN 106. Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description
SPN 106 Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description SPN FMI Description Possible Causes 106 3 MAP Sensor Signal Voltage High Open/high resistance in low reference circuit
More informationAdditions, Revisions, or Updates
1 29-13 1 1 29-13 SUBJECT DATE DD Platform GHG 14 SPN 3361 FMI 3, 4, 5 UPDATE January 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 GHG
More informationSU51 Air Springs. Copyright 1998 Inter-Industry Conference On Auto Collision Repair v.4.0
Uniform Procedures For Collision Repair UPCR SU51 Air Springs 1. Description This procedure describes the diagnosis, repair, and inspection of suspension air springs. 2. Purpose The purpose of this procedure
More information8803214-8803999 DIODE BOARD The diode board is located inside the lower control box. D15 D8 D7 D14 D5 D13 ART_2181 J1 14 8 D9 D10 7 1 R2 R1 R3 R4 TB1 8601 D11 D3 D12 D4 D1 D2 J1 Plug Pin Identification
More informationDIODE BOARD The diode board is located inside the lower control box. D15 D8 D7 D14 D5 D13 ART_2181 J1 14 8 D9 D10 7 1 R2 R1 R3 R4 TB1 8601 D11 D3 D12 D4 D1 D2 J1 Plug Pin Identification PIN # WIRE # SIGNAL
More informationAdditions, Revisions, or Updates
1 06 10-16 SUBJECT SPN 111 (CPC) (GHG17) and SPN 111 (CPC) (EPA07;EPA10;GHG14) DATE June 2016 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0191
More informationNote: If DTCs P0670 and P0684 are present, carry out DTC P0670 diagnosis before diagnosing DTC P0684.
2008 F-250 2008 PCED 6.4L Diesel SECTION 5: Pinpoint Tests Report a problem with this article Procedure revision date: 03/09/2010 AF: Glow Plug System AF: Introduction AF1 PRELIMINARY DIAGNOSIS te: If
More informationSPN 609 or Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description
SPN 609 or 3464 Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description SPN FMI Description Possible Causes 609 12 Main Processor Heartbeat Synchronization Fault Intermittent or poor
More informationCONTROLLER DIAGNOSTIC GUIDE
Proprietary tice: This document contains proprietary information which not to be reproduced, transferred, to other documents, disclosed to others, used for manufacturing or any other purpose without the
More informationPage 1 of 6 Pinpoint Test R: The Heated Seat is Inoperative Driver Refer to Wiring Diagrams Cell 119, Climate Controlled Seats for schematic and connector information. rmal Operation The heated seat module
More informationFAULT CODE 132 (SSS) Accelerator Position Sensor Circuit
FAULT CODE 132 (SSS) Accelerator Position Sensor Circuit Overview CODE REASON EFFECT Fault Code: 132 PID: P091 SPN: 91 FMI: 4 LAMP: Red SRT: 00-084 Low voltage detected at the accelerator position signal
More informationC1219 C1219-STEERING ANGLE SENSOR ERRATIC PERFORMANCE RAM Pickup 6.7L Eng Search. 7/13/2015 Printer Friendly View
2012 RAM Pickup 6.7L Eng 2500 1Search C1219 C1219-STEERING ANGLE SENSOR ERRATIC PERFORMANCE http://www2.prodemand.com/print/index?content=tabs&module=true&tab=true&terms=true&ymms=false&classname=&hideoptions=false
More informationSELF-DIAGNOSTIC TESTS
Page 1 of 10 1997 Chrysler Sebring 2.5L Eng JX SELF-DIAGNOSTIC TESTS NOTE: When using diagnostic tests, DO NOT skip any steps or incorrect diagnosis may result. Ensure battery is fully charged. in appropriate
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA10 DD Platform DATE: August 2010
NUMBER: 815 10 S.M. REF.: Listed in Table ENGINE: EPA10 DD Platform DATE: August 2010 SUBJECT: SPN 3226 FMI 13 SCR OUTLET NOX SENSOR SIGNAL NOT AVAILABLE ADDITIONS, REVISIONS, OR UPDATES Publication Number
More information8/18/2017 PPT AF: Glow Plug System - On Board Diagnostics 6.0L Diesel (Powertrain Diagnostics) 2004 Ford F-250 MotoLogic
2004 F-250 2004 PCED On Board Diagnostics 6.0L Diesel SECTION 5: Pinpoint Tests Report a problem with this article Procedure revision date: 02/19/2007 AF: Glow Plug System AF: Introduction AF1 PRELIMINARY
More informationFA: AMBIENT AIR TEMPERATURE (AAT) SENSOR: PINPOINT TEST
2014 Ford Taurus FWD V6-35L Vehicle > Powertrain Management > Computers and Control Systems > Testing and Inspection > Pinpoint Tests FA: AMBIENT AIR TEMPERATURE (AAT) SENSOR: PINPOINT TEST FA: Ambient
More informationCO22 Fan, Electric. Copyright 1998 Inter-Industry Conference On Auto Collision Repair v.4.0
Uniform Procedures For Collision Repair UPCR CO22 Fan, Electric 1. Description This procedure describes methods for the removal and installation of an electrically powered cooling system fan. Inspection
More informationSPN 1176/FMI 3 SPN 1176/FMI 4
NUMBER: 8 01 13 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 900 DATE: August 2013 SUBJECT: SPN 1176/FMI 3, 4 ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change DDC-SVC-MAN-0015
More informationIntake Air Temperature (IAT) Sensor
Page 1 of 5 Year = 2011 Model = Mustang Engine = 5.0L VIN = IDS Version = t Available Intake Air Temperature (IAT) Sensor This pinpoint test is intended to diagnose the following: IAT sensor (12A697) integrated
More informationP0456-EVAP PURGE SYSTEM SMALL LEAK
2014 Journey (2.4L L4) - JC P0456-EVAP PURGE SYSTEM SMALL LEAK Report a problem with this article Special Tools: Click to display a list of tools used in this procedure For a complete wiring diagram, refer
More information9-2 FAULT CODE DIAGNOSTICS AND REPAIR PROCEDURES
SERVICE BULLETIN (Not applicable to Mack Trucks Australia) (Supersedes bulletin SB-221-032 dated 3/20/03) NUMBER: SB-221-032 DATE: 12/4/03 MODEL: All 9-2 FAULT CODE DIAGNOSTICS AND REPAIR PROCEDURES A
More informationDH - RAM 1500/2500 PICKUP - 6.7L CUMMINS TURBO DIESEL
007 - DH - RAM 500/500 PICKUP - 6.7L CUMMINS TURBO DIESEL U004-CAN B BUS (-) CIRCUIT OPEN For a complete wiring diagram, refer to the Wiring Information. When Monitored: With the ignition on and battery
More informationThe Power Systems Industry Experts. Installation Instructions. PT100 Stationary Generator Monitoring System
The Power Systems Industry Experts Installation Instructions PT100 Stationary Generator Monitoring System PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION Planning the Installation The monitoring unit
More informationFUSES AND RELAYS FUSES AND RELAYS GENERAL OVERVIEW AND OPERATION PROCESS 1. GENERAL INFORMATION...
GENERAL 1. GENERAL INFORMATION... 3 OVERVIEW AND OPERATION PROCESS 1. COMPARTMENT... 2. ELECTRIC COMPONENTS LOCATOR.. 6 12 01-3 FUSES & RELAYS GENERAL 1. GENERAL INFORMATION 1. Before starting repairs
More information2000 Town Car Workshop Manual
Page 1 of 30 SECTION 204-05: Vehicle Dynamic Suspension DIAGNOSIS AND TESTING Procedure revision date: 05/27/1999 Vehicle Dynamic Suspension Refer to Wiring Diagrams Cell 41, Rear Air Suspension for schematic
More informationU010C-LOST COMMUNICATION WITH TURBOCHARGER/ SUPERCHARGER CONTROL MODULE
2014 - D2 - RAM 3500 PICKUP - 6.7L I6 CUMMINS TURBO DIESEL U010C-LOST COMMUNICATION WITH TURBOCHARGER/ SUPERCHARGER CONTROL MODULE For a complete wiring diagram, refer to the Wiring Information. IGN RELAY-
More informationNOTE: The Smart Junction Box (SJB) is also known as the Generic Electronic Module (GEM).
SECTION 417-01: Exterior Lighting 2009 Mustang Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 05/23/2008 Reversing Lamps Special Tool(s) 73III Automotive Meter 105-R0057 or equivalent Vehicle
More informationRev Rev. Additions, Revisions, or Updates
1 4 89-12Rev SUBJECT DATE SPN 5927/FMI 2 and 7 - GHG14 April 2012 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 5927/FMI 2 - DDC-SVC-MAN-0084 DD Platform
More informationC.E. Niehoff & Co. C653/C653A and C625 Alternators Troubleshooting Guide NOTICE. Hazard Definitions. Battery Charge Volt and Amp Values
C.E. Niehoff & Co. C653/C653A and C625 Alternators Troubleshooting Guide Hazard Definitions These terms are used to bring attention to presence of hazards of various risk levels or to important information
More informationSPN 723/FMI 3, 8, 10, 11, 31 - All Years February SPN 723/FMI 3 - All Years. SPN 723/FMI 8 - All Years. SPN 723/FMI 10 - All Years
1 49-13 1 1 49-13 SUBJECT DATE SPN 723/FMI 3, 8, 10, 11, 31 - All Years February 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 723/FMI 3 - All Years
More informationSPN 110. Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description. SPN FMI Description Possible Causes
SPN 110 Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description SPN FMI Description Possible Causes 110 0 Engine Coolant Temperature Stuck thermostat Overheating Low coolant Cooling
More informationOn Board Diagnostics II A PCED
1998 PCED On Board Diagnostics II A SECTION 5A: Pinpoint Tests HA: Natural Gas Fuel Control HA: Introduction HA30 DTCS P05, P0141, P0155 AND P0161: HO2S HEATER SIGNAL CIRCUIT IS OPEN, SHORTED TO GROUND,
More information1995 Town Car/Crown Victoria/Grand Marquis
Page 1 of 11 PINPOINT TEST A: SHIFT SOLENOIDS Pinpoint Test A Shift Solenoids DTCs: P0781, P0782, P0783 Shift Errors P0750, P0755 Solenoid Circuit Failures P0751, P1751 Shift Solenoid. 1 Malfunction P0756,
More informationGENERAL <ELECTRICAL>
00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................................. 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION
More informationGENERAL <ELECTRICAL>
00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................... 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION FOR DIAGNOSIS.......
More informationAdditions, Revisions, or Updates
1 01 29-14 SUBJECT DATE SPN 3511/FMI 3 and 4 - GHG14 January 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change SPN 3511/FMI 3 - DDC-SVC-MAN-0084 GHG14 DD Platform
More informationSPN 3232 or Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description
SPN 3232 or 3271 Suspect Parameter Number (SPN) and Failure Mode Indicator (FMI) Description SPN FMI Description Possible Causes 3232 5 EGO Bank A Post Cat Heater Malfunctioning heater relay. Circuit Open/Shorted
More informationDIAGNOSIS AND TESTING
308-07A-1 DIAGNOSIS AND TESTING Electronic Shift Visual Inspection Chart Mechanical Electrical 308-07A-1 Refer to Wiring Diagrams Cell 34 for schematic and Halfshafts Junction box (JB) mini connector information.
More informationFuel Injector Control Module (FICM ) Low Voltage
Page 1 of 6 Year = 2006 Model = F-Super Duty Engine = VIN = Fuel Injector Control Module (FICM ) Low Voltage Circuit Function The FICM requires a 12-volt power source. The FICM receives power from the
More informationInstallation Instructions Crossfire Spreader 64740, 66263, and 66264
Form 1-1091R1 July 2016 Installation Instructions Crossfire Spreader 64740, 66263, 64742 and 66264 Determining Vehicle Payload It is necessary to calculate the available material payload to prevent overloading
More informationAdditions, Revisions, or Updates
03 57-17 1 03 57-17 SUBJECT DATE SPN 625 (CPC) (GHG17) March 2017 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0191 GHG17 DD Platform SPN 625/FMI
More informationAdditions, Revisions, or Updates
1 6 05-13 SUBJECT DATE SPN 625/FMI 9 EPA10 - GHG14 June 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 EPA10/ GHG14 DD Platform SPN 625/FMI
More information