RC Conversion Kit for Tamiya 1/35 M1A1/A2 Tank - with MTC-2, ACU and GSU
|
|
- Charles McCarthy
- 5 years ago
- Views:
Transcription
1 RC Conversion Kit for Tamiya 1/35 M1A1/A2 Tank - with MTC-2, ACU and GSU User Manual Attention! 1) This kit is designed for experienced model makers. It may be difficult for beginners. Please read this manual thoroughly to see if you have the required skills and tools. 2) Cutting tools are used frequently in this kit. Extra care should be taken to avoid injury. Wear hand gloves and eye protection spectacle if necessary. 3) Keep room well ventilated when working with cements, paints and organic solvents. 4) Visit for addition tips and update information. scriber apply cement side cutter do not apply cement modelling knife apply instant glue carving knife wait overnight all purpose glue solder Attention! Copyright Page 1
2 1 Lower hull Drill 3mm holes Remove wheel shaft carefully. Collect 14 wheel shafts for later use. 2A Suspension arms wheel shaft from lower hull Torsion bar Fixture Place torsion bar on top of fixture. Note different position for left and right arms. Insert wheel shaft and apply instant glue carefully. Attention - Too much glue will stick arm to fixture! The suspension arms will tilt under loading. The shaft is tilt in purpose for compensation. Copyright Page 2
3 2B Suspension arms 67x13x1mm PS plate C 30x13x1mm PS plate 67x13x1mm PS plate A B L7 L6 L5 L4 L3 L2 L1 R7 R6 R5 R4 R3 R2 R1 Check labels! Hold with cellophane tape L3 C B R3 Position L3 on top of B G-Clamp wooden block wooden block Table 1) Hold all suspension arms with cellophane tape. 2) Cut PS plates A, B, C. Glue A, B first. Position L3 on top of B and glue C. 3) Apply lots of cement to PS plate and lower hull. Use G-clamp or apply weights to press PS plate firmly to lower hull. 4) Wait till cement has cured completely. Attention - Do not use instant glue! It will spread along torsion bars and stick suspension arms. Use G-clamp or apply weights MTC-2 mount 3 Motor and MTC-2 mounts Motor mount Copyright Page 3
4 4 Turret M1A1 M1A2 Remove Remove snap catch 5 M1A2 2 4 snap catch M1A1 2 5 snap catch attach to upper turret 4 Use 1mm PS plate to make 4 pairs of snap catch. 10 snap catch Copyright Page 4
5 5 Turret ring gear Acrylic part A2 Keep gear teeth away from instant glue. To have a smooth turret rotation, turret ring gear must be positioned with high accuracy: 1) Insert the ring gear fixture to upper hull. 2) Position the ring gear in position as shown. 3) Apply instant glue. Take care not to stick the fixture! upper hull ring gear fixture ring gear ring gear ring gear fixture ring gear fixture ring gear 6 Speaker Copyright Page 5
6 7 Servo assembly, ACU and GSU Install servo assembly 1) Position servo assembly as shown. 2) Check alignment before applying instant glue. 3) Apply instant glue carefully. Too much glue will stick moving parts! check alignment check alignment Install ACU & GSU 1) Position ACU and GSU as shown. Apply clement to secure. 8A Gun mantlet (M1A1) Remove sand paper B39 Drill 3mm hole Enlarge hole by cutter polish 6.5mm hole B28 chamfer Drill 1.5mm hole B29 Copyright Page 6
7 8B Gun mantlet (M1A2) Remove F15 F13 7 sand paper F16 F14 polish 6.5mm hole 9 Machine gun LED Drill 1.5mm hole Drill 1mm hole Drill Jig B27 1) Drill half depth from one end 2) Drill through from other end B27 machine gun LED 1) Use all purpose glue to attach the machine gun LED 2) Do not apply glue to the optical fibre! 10 Gun barrel Drill 3.2mm hole metal gun barrel Remove Copyright Page 7
8 11 Attach gun barrel and gun mantlet recoil spring insert metal gun barrel and secure set screw 1) Use all purpose glue to attach the gun mantlet 2) Test the recoil mechanism and make sure the gun mantlet is well aligned 12 Attach gun flash LED Explode LED during recoil press fit to gun barrel here do not apply cement adjust recoil travel if necessary Copyright Page 8
9 13 Attach turret Step2: Rotate and secure the locking plate Step1: Engage pinion into ring gear. 14 Motor and sprockets M2.6x3mm mm hexagonal nut Move to adjust track tension. Track will detach easily either too tight or too loose. Adjust till tracks run smoothly. Tips: 1) Align sprocket with last wheel. Prevent sprocket touching the side skirt and the last wheel. 2) Check if all wheels are smooth to turn. 3) Apply baby powder to new tracks for smooth running. There is little space between the side skirts and the track at the idle wheel. Insert an 103mm sprue to ensure enough space for tracks. Copyright Page 9
10 15 Using Lipo battery (optional) Lipo battery can be dangerous if not use properly! Follow all safety precautions and always use a dedicated Lipo charger. 1) Use 7.4V/2Cell Lipo battery ( mAh) 2) Make sure battery is small enough to put inside the lower hull. 3) Solder connector for MTC-2 as shown. Keep original connector for charging. solder and wrap with heat shrink tubing 7.4V/2Cell Lipo 1300mAh + - MTC-2 power connector MTC-2 will damage if polarity is not correct! 16 Antenna ( for FM/AM receivers) 0.5mm steel wire antenna wrap antenna end with cable tubing 0.5mm pin connectors to receiver 1.2mm cable 1) Only required for FM/AM receivers. 2) Build external antenna only when control is not stable. 3) Construct antenna connector as shown. 4) To avoid interference, keep antenna cable away from motor cables. Copyright Page 10
11 17 Lower hull connections Secure MTC-2 by M2 x 3 screws Spektrum 2.4G AR6110e micro receiver AAAx6 battery case power switch Using 6 Cell AAA NiMH battery Secure MTC-2 by M2 x 3 screws Spektrum 2.4G AR6110e micro receiver 2 Cell Lipo battery power switch Using 2 Cell Lipo battery Copyright Page 11
12 18 Turret connections 1) Connect servos, speaker and LEDs according to ACU and GSU manual. 2) Tie up cables neatly and away from moving parts. Copyright Page 12
Ultimate EP. Before commencing assembly, please read these instructions thoroughly. I NSTRUCTI ON M ANUAL. Warning! This model is not a toy.
I NSTRUCTI ON M ANUAL Before commencing assembly, please read these instructions thoroughly. Ultimate EP (GM05) Specifications Wing Span: 3.5 in / 85 mm Wing Area: 357 sq in / 3 sq dm Flying Weight: 4
More informationBefore commencing assembly, please read these instructions thoroughly.
I NSTRUCTI ON M ANUAL Before commencing assembly, please read these instructions thoroughly. (GM034XM) Specifications Wing Span:28.7 in / 730 mm Wing Area:310 sq in / 20 sq dm Flying Weight:28.5 oz / 805
More informationMiG-29 Retract Kit (for the HET-RC Mini Air Retract System)
MiG-29 Retract Kit (for the HET-RC Mini Air Retract System) The MiG-29 Retract Kit was designed to allow the easy installation of the HET-RC mini Air Retract system into the twin EDF MiG-29. We recommend
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1404mm (55.3in) - Length: 1134mm (44. 6 in) - Flying weight: 3.2-3.4 kg - Covering type: Genuine ORACOVER - Spinner size: scale type (not included) - Radio: 4 channel minimum
More informationSIZE.120 OR 30CC SCALE 1:5 ARF
PC21 PILATUS MK2 SIZE.120 OR 30CC SCALE 1:5 ARF SPECIFICATION - Wingspan: 1772mm (69.72in) - Length: 2019mm (79.5 in) - Flying weight: 6.4-7.2 kg - Wing area: 57.6 dm2 - Wing loading: 113g/dm2 - Wing type:
More informationPlease read all instructions carefully before assembly and flight!
Please read all instructions carefully before assembly and flight! Thank you for purchasing the Mig-15. This model is designed for the intermediate to advanced flyer. The model is receiver ready and includes
More informationszd-45 ogar Before commencing assembly, please read these instructions thoroughly. I NSTRUCTI ON M ANUAL Warning! This model is not a toy.
I NSTRUCTI ON M ANUAL Before commencing assembly, please read these instructions thoroughly. szd-5 ogar Specifications Wing Span: 98.5 in / 2500 mm Wing Area: 667 sq in / 3 sq dm Flying Weight: 8 oz /
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1410mm (55.5 in) - Length: 1278mm (50.3 in) - Flying weight: 3.2-3.4 kg - Wing area: 41.3 dm2 - Wing loading: 75g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationBefore commencing assembly, please read these instructions thoroughly.
I NSTRUCTI ON M ANUAL Before commencing assembly, please read these instructions thoroughly. Specifications Wing Span: 33 in / 850 mm Wing Area: 299 sq in / 19.3 sq dm Flying Weight: 24 oz / 680 g Fuselage
More informationRTR Instruction Manual
OFNA Racing 22692 Granite Way, Ste. B Laguna Hills, Ca. 92653 (949) 586-2910 Www.ofna.com RTR Instruction Manual PURE COMPETITION... PRE-ASSEMBLED ASSEMBLED CHASSIS WITH RADIO AND ENGINE REQUIRED FOR OPERATION
More informationNew Generation Rear Wheel Drive
New Generation Rear Wheel Drive ABC HOBBY ORIGINAL RADIO CONTROL CAR Instruction Manual Study the instructions thoroughly before assembly. REAR 2 WHEEL DRIVE REAR MOUNTED MOTOR BELT DRIVE DOUBLE DECK CHASSIS
More informationWorking Stirling-Motor
PARTS LIST 113.174 Working Stirling-Motor Please Note The OPITEC range of projects is not intended as play toys for young children.they are teaching aids for young people learning the skills of Craft,
More informationMS:159 ASSEMBLY MANUAL. Graphics and specifications may change without notice.
ASSEMBLY MANUAL MS:159 Graphics and specifications may change without notice. Specifications: Wing span ----------------------------61.8in (157cm). Wing area -----------------1100.5sq.in (71.0sq dm). Weight
More informationInstruction Manual book
book ITEM CODE:BH 115. SPECIFICATION Wingspan : 6,000 mm 236,22 in. Length : 2,740 mm 107,87 in. Weight : 17.5kg 38.5Lbs. Radio : 08 channels. Servo : 07-08 HS-5685MH(HITEC) Battery : 2 Cells-Li-Po 7.4V
More informationAtlas Silver Series HO RS-3 (2014 Release) Tsunami Digital Sound Decoder Installation Notes
Atlas Silver Series HO RS-3 (2014 Release) Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into an Atlas Silver
More informationRADIO CONTROL MODEL ASSEMBLY INSTRUCTIONS. Wasp
RADIO CONTROL MODEL ASSEMBLY INSTRUCTIONS Wasp TRAINER Almost ready-to-fly Wingspan 1520mm Fuselage length 1105mm Engine: 40-46 2T / 52-60 4T Electric Motor: 600-700W Radio: 5 channel / 4-5 servo RC Functions:
More informationFIRE PHOENIX RADIO CONTROLLED AIRPLANE
FIRE PHOENIX RADIO CONTROLLED AIRPLANE ASSEMBLY AND OPERATION INSTRUCTIONS YIN YAN MODEL TECH. MFT. 1 SPECIFICATIONS Material EPO Plane Battery Li-Po 1300mAh 11.1V Radio 4 Channel Wing Span 1200mm Length
More information40 EP Gee Bee Y Scale ARF V2 Instruction Manual Specs:
40 EP Gee Bee Y Scale ARF V2 Instruction Manual Specs: Wing Span: 40" Overall length: 30" Wing area: 306 sq. in Ready to fly weight: 28~32 oz Motor/Engine: Electric: Uranus-28309 brushless outrunner motor,
More informationPlease read all instructions carefully before assembly and flight!
c c Please read all instructions carefully before assembly and flight! Thank you for purchasing the. This model is designed for the intermediate to advanced flyer. The model is receiver-ready and includes
More informationComplete Kit Freightliner COE
Complete Kit Freightliner COE All components displayed.(complete kit #55 with radio kit VG400, battery charger VC600, 3 Speed transmission #165, aluminum headache rack #1002, 2nd differential #117, inner
More informationAthearn SD40T-2 Tsunami Digital Sound Decoder Installation Notes
Athearn SD40T-2 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn Ready-To-Roll HO SD40T-2. Skill Level 2: The entire
More informationYAK54 MK2. GP/EP size.120/20cc SCALE 1:4 ¾ ARF. Instruction Manual. version. version
Instruction Manual GP EP version version GP/EP size.10/0cc SCALE 1:4 ¾ ARF SPECIFICATION - Wingspan: 168 (66.3 in) - Length: 1605mm (63.1 in) - Flying weight: 4700-500 gr - Wing area: 54.7 dm - Wing loading:
More informationMicro Remote Control UFO Quadcopter KARCTUFOMNA Quick Start Guide Please read this guide carefully before use.
Micro Remote Control UFO Quadcopter KARCTUFOMNA Quick Start Guide Please read this guide carefully before use. Product Layout Battery Installation To load the batteries: Open the battery cover on the back
More information3D EP in / 1000mm. Wing Span Wing Area Flying Weight Fuselage Length. 5 oz / 720g 39 in / 990mm INSTRUCTION MANUAL.
ALMOST-READY-TO-FLY INSTRUCTION MANUAL 3D EP Requires : 4-channel radio w/ 4 micro servos, Outrunner Motor KM028300 w/ Propeller Adaptor HW234000 20A brushless ESC, 3 cells.v 200 mah Li - Po battery &
More informationSpecifications. *Specifications are subject to change without notice.*
INSTRUCTION MANUAL Requires : 4-channel radio w/ 4 micro servos, Ducted Fan Propulsion Unit PL6800010 and Outrunner Motor KM0283110, 30A (burst 35A) brushless ESC, 3 cells 11.1V 15C discharge 2100 mah
More informationSpecifications ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Specifications Length : 6 mm Height : 218 mm Main Blade : 325 mm Main Rotor Diameter : 723 mm Tail Rotor Diameter : 150 mm Motor Pinion Gear : 16T (14T) Main Drive Gear : 150T Main
More informationInstruction Manual book
Instruction Manual book ITEM CODE:BH118. SPECIFICATION Wingspan : 1,050 mm 41.34 inches. Length : 950mm 37.4 inches. Weight : 1 kg 2.2 lbs. Radio : 04 channels. Servo : 4 mini servos. Motor : KMS 2814/05
More informationBy: LEAGUE MODEL CO., LTD
By: LEAGUE MODEL CO., LTD INSTRUCTION ASSEMBLY MANUAL Specifications Length 1400MM(55.0in) Wing Span 1520MM(59.8in) Wing Area 46dm 2 (713sq.in) Weight 1650g Radio 4channel 5servo Engine Requirements: 2C-
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 2567mm (101in) - Length: 2190mm (86.2 in) - Flying weight: 11-13 kg - Wing area: 101 dm2 - Wing loading: 99g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER -
More informationRadio control model INSTRUCTION MANUAL PYLON RACING. Wingspan: 1148mm (45.2 ) Radio : 4 channels Engine : two-stroke
VQA038 VQA039 Radio control model INSTRUCTION MANUAL MAGIC PYLON RACING Wingspan: 1148mm (45.2 ) Radio : 4 channels Engine :.25 -.32 two-stroke WARNING! This radio control model is not a toy. If modified
More informationINSTALLATION INSTRUCTIONS
Ultrasonic Rear Park Aid Kit (Kit # 9002-3000) INSTALLATION INSTRUCTIONS Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 4 Ultrasonic
More informationInstallation Instruction EPP /92
E L E C T R I C A L P R O D U C T S. D I V I S I O N Installation Instruction EPP 0275 8/92 Terminations for Screened Single Core Plastic and Rubber Insulated Cables 7.2 kv to 36 kv without Armour Before
More informationAMPS Atlanta Club Project 2016 Part 1. Afrika Corp Tiger I Initial
AMPS Atlanta Club Project 2016 Part 1 Afrika Corp Tiger I Initial Afrika Corp Tiger s After last session there was a lot of interest on this subject, especially about Tiger 131 the only running Tiger I
More informationKato P42 Tsunami Digital Sound Decoder Installation Notes
Kato P42 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes the procedure for installing a TSU-KT1000 Digital Sound Decoder into a Kato HO P42 locomotive. Skill Level
More information(Glider) ASSEMBLY MANUAL
(Glider) MS:132 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------118.1in (300cm). Wing area ---------------------902.1sq.in
More informationRight On Replicas, LLC Step-by-Step Review * Mack Fire Pumper 1:32 Scale Revell Model Kit # Review
Right On Replicas, LLC Step-by-Step Review 20150915* Mack Fire Pumper 1:32 Scale Revell Model Kit #85-1945 Review The Mack CF600 Pumper is a familiar fire truck that is still widely used in firehouses
More informationAthearn RTR EMD CF7 Tsunami Digital Sound Decoder Installation Notes
Athearn RTR EMD CF7 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn HO Ready-To-Roll EMD CF7. Skill Level 2: The entire
More informationInstallation Instructions for the Plug & Play Remote Start Package (EVOCHR4)
T6002 v1.1 02/2013 Installation Instructions for the Plug & Play Remote Start Package (EVOCHR4) For CHRYSLER Town & Country 2008-2012 Review the remote start installation manual for safety instructions!
More informationI n s t r u c t i o n M a n u a l. Instruction Manual SPECIFICATION
I n s t r u c t i o n M a n u a l Instruction Manual SPECIFICATION - Wingspan: 3200mm (125,9 in) - Length: 1650mm (64,9 in) - Flying weight: 3000gr 3200gr - Wing area: 64.5 dm2 - Wing loading: 46g/dm2
More informationInstruction Manual book
Instruction Manual book ITEM CODE:BH118. SPECIFICATION Wingspan : 1,050 mm 41.34 inches. Length : 950mm 37.4 inches. Weight : 1 kg 2.2 lbs. Radio : 04 channels. Servo : 4 mini servos. Motor : BL2215/20
More informationHandyman Motor Capacitor Meter PART NO
Handyman Motor Capacitor Meter PART NO. 2225174 To test a motor-run capacitor in the field with no capacitance meter at hand, you had to hook up the capacitor through an extension cable to a 120V wall
More informationAthearn RTR EMD GP35 Tsunami Digital Sound Decoder Installation Notes
Athearn RTR EMD GP35 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn HO Ready-To-Roll EMD GP35. Skill Level 2: The
More informationEXTRA 330LX. Specifications: Code: SEA274. Graphics and specifications may change without notice. ASSEMBLY MANUAL
ASSEMBLY MANUAL EXTRA 330LX Code: SEA274 Graphics and specifications may change without notice. Specifications: Wingspan---------------82.0 in (208.2 cm). Wing area---------------1349.4 sq.in ( 87.1 sq.dm).
More informationROPE DANCER INSTRUCTION MANUAL:
Educational Design Robot ROPE DANCER INSTRUCTION MANUAL: Model WTR-RD1 2010 AREXX - THE NETHERLANDS CONTENT 1. Product information Rope Dancer 3 2. General assembly information 4 2.1 Parts list Rope Dancer
More informationInstallation Instructions for the Plug & Play Chrysler/Dodge/Jeep Remote Start Package w/mux T5
v1.01 12/14/2102 Installation Instructions for the Plug & Play Chrysler/Dodge/Jeep Remote Start Package w/mux T5 Review the remote start installation manual for safety instructions! Overview Your kit consists
More informationInstallation Instruction EPP /02. Terminations for Screened Single Core Polymeric Insulated Cables up to 24 kv without Armour
R Installation Instruction EPP-0778-11/02 Terminations for Screened Single Core Polymeric Insulated Cables up to 24 kv without Armour Type: IXSU-F / OXSU-F Tyco Electronics Raychem GmbH Energy Division
More informationPHOENIX ENIX Features of the Phoenix-60 : 2.3 Connecting the Motor. 2.4 Reversing Rotation. 2.5 Connecting the Receiver
PHOENIX ENIX-60 Warning! High power motor systems can be very dangerous! High currents can heat wires and batteries, causing fires and burning skin. Follow the wiring directions carefully! Model aircraft
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 6000mm (236.2 in) - Length: 2873mm (113.1 in) - Flying weight: 14-18 kg - Wing area: 219.4 dm2 - Wing loading: 64g/dm2 - Wing type: HQ airfoils - Covering type: Genuine ORACOVER
More informationArrow Shark 2016 M8 II Sterndrive - Collector Edition Owner Manual. M8 II weight: 925 grams Dimensions
Arrow Shark 2016 M8 II Sterndrive - Collector Edition Owner Manual M8 II weight: 925 grams Dimensions Parts List M8V2#0001 Billet Lower Unit M8V2#0013 Steering Cable Assembly M8V2#0002 Steering Arm Housing
More informationRECOMMENDED MOTOR AND BATTERY SET UP
Instruction Manual SPECIFICATION - Wingspan: 1418mm (55.8 in) - Length: 1314mm (51.7 in) - Flying weight: 2700-3200 gr - Wing area: 36.8 dm2 - Wing loading: 76g/dm2 - Wing type: Naca airfoils - Covering
More informationCHEVROLET TAHOE/DENALI/AVALANCHE/YUKON/ SILVERADO/SIERRA 2007+
CHEVROLET TAHOE/DENALI/AVALANCHE/YUKON/ SILVERADO/SIERRA 2007+ INSTALLATION INTRODUCTION 1. REMOVING THE FENDER AND DOORS FROM THE A-PILLAR AND DISCONNECTING THE WIRE HARNESS @ THE DOOR JAM 2. REMOVING
More informationP-40C TOMAHAWK. Instruction Manual Book. Item code: BH % ALMOST READY TO FLY SPECIFICATION
Instruction Manual Book. P-40C TOMAHAWK INCLUDING AIR RETRACT. AIR UP, AIR DOWN, TURN AND TWIST OLEO STRUTS LANDING GEAR. ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED.
More informationInstruction Manual book
book (pusher propeller) ITEM CODE:BH 142 SPECIFICATION Wingspan : 1,450mm 57.09 in. Length : 1,165 mm 45.87 in. Weight : 3.3kg 7.26 Lbs. Radio : 05 channels. Servo : 07 size (29 x 13 x 30) mm. Electric
More information1:6 BLACK BRANT II. c o s m o d r o m e r o c k e t r y
c o s m o d r o m e r o c k e t r y 1:6 BLACK BRANT II This kit is capable of use with high thrust motors. It is therefore strongly recommended that epoxy be used throughout the construction of this kit.
More informationFLEX CONNECTOR HEAT SHRINK SLEEVE INSTALLATION GUIDE
FLEX CONNECTOR HEAT SHRINK SLEEVE INSTALLATION GUIDE The information in this publication is provided for reference only. While every effort has been made to ensure the reliability and accuracy of the information
More informationRe-Energy.ca - Solar Electricity - Build Your Own Solar Car
Backgrounder Build Your Own Solar Car Back to Page 1 Build It! These step-by-step instructions provide you with a plan for making a basic solar car. If you can think of ways to improve the design of your
More informationFlyzone Spitfire FF to R/C Conversion Instructions
Flyzone Spitfire FF to R/C Conversion Instructions Hobbico Flyzone EP FF airplanes have been around for years, with exciting new models being added constantly. The recent interest shown by R/C modelers
More informationASSEMBLY MANUAL. Kit features. MS:110
MS:110 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span-------------------------------------------------- 62.9 in---------------------------------------
More informationINSTALLATION INSTRUCTIONS
2015 - Ford Mustang Qi Wireless Charging Kit (Kit # FDMC-1222) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Qi Wireless Charging
More informationDARMAN. ENDURA II Cloth Towel Cabinet Product Guide. Manufacturing Company, Inc Lincoln Ave., Utica, NY 13502
ENDURA II Cloth Towel Cabinet Product Guide Page 2, 3 4, 5 6, 7 8, 9 10 11 12 Parts Covered Hood Assembly Mechanism Back Assembly Bin and Towel Guide Service Bulletin - Roller Warranty and Maintenance
More informationInstruction Manual book
book ITEM CODE:BH 145 SPECIFICATION Wingspan: 6,000mm 236.22 in. Length : 2,800 mm 110.24 in. Weight : 18.5 kg 40.7 Lbs. Parts listing required (not included). Radio : 07-08 channels. Servo : 09-10 standard
More informationPHOENIX Features of the Phoenix-10 : 2.3 Connecting the Motor. 2.4 Reversing Rotation. 2.5 Connecting the Receiver
Warning! High power motor systems can be very dangerous! High currents can heat wires and batteries, causing fires and burning skin. Follow the wiring directions carefully! Model aircraft equipped with
More informationMR-1. Please read and understand all instructions before building!
MR-1 This kit contains all the parts necessary* to build a flying high power rocket: (1) Pre-slotted main airframe (1) Nose cone with strap (3) Fins (1) Transition (1) Airframe section 1 long (1) Piston
More informationFigure 1. A CheapBot Robot
A CheapBot controller needs a robot body to function. An ideal robot body for the beginner consists of two sheets of Syntra plastic, separated by four bolts. The bottom deck contains the robot controller
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 2190mm (86.2 in) - Length: 1907mm (75 in) - Flying weight: 9000-12000 gr - Wing area: 92 dm2 - Wing loading: 98g/dm2 - Wing type: Naca airfoils - Retract gear type: Air-retract
More informationAthearn SD40 Tsunami Digital Sound Decoder Installation Notes
Athearn SD40 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn Ready-To-Roll HO SD40. Skill Level 2: The entire installation
More informationRADIO CONTROL MODEL HURRICANE
RADIO CONTROL MODEL VQAA040G VQAA040B HURRINE Almost ready to fly SPECIFITIONS Wingspan...63 in. / 161cm Length...50 in. / 129cm Engine...50~60 2T / 70~90 4T Or Electric equivalent. RC Functions: Motor
More informationUser Manual RC Electric Parts Electric Speed Controller (ESC) for Brushless Motors
User Manual RC Electric Parts Electric Speed Controller (ESC) for Brushless Motors Thank you for using RC Electric Parts ESC designed to meet your hobbies needs. As you'll find the ESC's settings are programmable
More informationInstallation Tips for your Remote Start/Keyless Entry (for Mazda Vehicles) v3.1 Updated 9/22/2012
Installation Tips for your Remote Start/Keyless Entry (for Mazda Vehicles) v3.1 Updated 9/22/2012 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote
More informationRTR Instruction Manual
RTR Instruction Manual OFNA RACING 22692 Granite Way, Ste. B Laguna Hills, CA. 92653 PRE-ASSEMBLED ASSEMBLED CHASSIS WITH RADIO AND ENGINE REQUIRED FOR OPERATION THINGS NEEDED You will need to buy a few
More informationFlyzone P-40 FF to R/C Conversion Instructions
Flyzone P-40 FF to R/C Conversion Instructions Hobbico Flyzone EP FF airplanes have been around for years, with exciting new models being added constantly. The recent interest shown by R/C modelers in
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1420mm (55.91 in) - Length: 1370mm (53.94 in) - Flying weight: 2600-2800 gr - Wing area: 41.6 dm2 - Wing loading: 65g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationRevision Date: Building a dual pump system for an open boat. Description:
Disclaimer: The information is provided as-is. The author(s) accepts no liability for the accuracy, availability, suitability, reliability and usability. The following information is in the public domain
More informationTip: Difficult Conversions for F800 (3026) and 3111 Date: Led lighting added, LED Addition 3111
Hi All, It s good to revisit previous conversions and see if you can improve on what has been done before. I decided to add LED lighting to my F800 (3026) and 3111. This document update shows how it was
More informationTURBO BEAVER. Instruction Manual Book. Item code: BH % ALMOST READY TO FLY ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER
Instruction Manual Book. TURBO BEAVER ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 2,250 mm (88.58 in). Length: 1,675 mm ( 65.94 in). Weight:
More informationPage 1 of 25. Service and Repair REMOVAL SIZED FOR PRINT. Related Components
Page 1 of 25 Service and Repair REMOVAL Related Components Page 2 of 25 1ZZ-FE Page 3 of 25 2ZZ-GE 1. REMOVE UPPER FRONT FENDER APRON SEAL AND UPPER RADIATOR SUPPORT SEAL 2. DRAIN ENGINE COOLANT 3. REMOVE
More informationRTR KITS - REQUIRED FOR OPERATION
Strong Front and Rear chassis braces. Tuned Polished Dual Chamber racing pipe. Unique adjustable chassis width of 310mm or 330mm. High performance.26 engine with Shaft Start Motor handle. Full race Offset
More informationTable of Contents WARN INDUSTRIES PAGE A1
INSTALLATION INSTRUCTIONS AND OPERATORS GUIDE ProVantage Bucket Conversion Kit Part Number: 84133 (50 ), 83133 (54 ) and 85133 (60 ) Application: Front Mount Plow* * Not recommended for use with Center
More information50CC PAULISTINHA. Before commencing assembly, please read these instructions thoroughly.
I NSTRUCTI ON M ANUAL Before commencing assembly, please read these instructions thoroughly. 50CC PAULISTINHA (GA065) Specifications Wing Span: 118 in / 3000 mm Wing Area: 1990 sq in / 18 sq dm Flying
More informationModel E600 Tarping System
10 Boulder Parkway N. Oxford, MA 01537 866-353-5826 pioneersales@wastequip.com www.pioneercoverall.com Model E600 Tarping System Installation Instructions WARNING: In order to prevent damage, the tarp
More informationINSTRUCTION. FOX4x4 Kit Features:
INSTRUCTION Congratulations on your purchase of the new SWORKz 1/10 scale FOX4x4 off-road ready to run brushless power CAGE buggy. Please read this manual thoroughly before you attempt to drive your FOX4x4.
More informationBuilding a Battery Car and other technical concerns
Building a Battery Car and other technical concerns Presented by The Tucson Garden Railway Society, The Tucson Botanical Garden Nick C. Buchholz presenting 1 Where to start. Decisions- What Locomotive?
More informationInstruction Manual. Wingspan : 1400 mm (55.12 inch) : 1480 mm (58.27 inch) : 5500gr gr. : 6-9 channel/ 8 servo high torque,1 standard
Wingspan : 1400 mm (55.12 inch) g Length : 1480 mm (58.27 inch) Weight : 5500gr - 6000gr Radio : 6-9 channel/ 8 servo high torque,1 standard Engine : GT 22 OS KIT CONTENTS: We have organized the parts
More informationGM G-BODY LSD INSTALLATION
GM G-BODY 1979-1987 LSD INSTALLATION INSTALLATION INTRODUCTION 1. REMOVING THE FENDER AND DOORS FROM THE A-PILLAR AND DISCONNECTING THE WIRE HARNESS @ THE DOOR JAM 2. REMOVING THE EXISTING DOOR HINGES
More informationInstallation Instructions for the Plug & Play Remote Start Package (EVOCHR5)
T6018 v1.1 02/2013 Installation Instructions for the Plug & Play Remote Start Package (EVOCHR5) For DODGE Nitro 2007-2011 Review the remote start installation manual for safety instructions! Overview Your
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1600mm (63 in) - Length: 1285mm (50.5 in) - Flying weight: 2800-3200 gr - Wing area: 40.1 dm2 - Wing loading: 78g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationInstruction Manual book
Instruction Manual book ITEM CODE:BH135 SPECIFICATION Wingspan : 4,200mm. 163.35 in. Length : 2,100 mm. 82.68 in. Weight : 7,6 kg. 16.72lbs Radio : 07 channels. Servo : 05 06 standard high torque servos,
More informationASSEMBLY MANUAL. Graphics and specifications may change without notice.
NEMESISMS: SEA 111 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications Wing span------------------------------------- 55.9in ------------------------------- 142cm. Wing
More informationInstruction Manual book
book SPECIFICATION Wingspan : 2,310 mm 90.94 in. Length : 1,750 mm 68.90 in. Weight : 8.4 kg 18.48 Lbs. Radio : 06 channels. Servo : 09 servos + 2 mini servos (elevator). Engine : 45-55CC gas. Made in
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1669mm (65.7in) - Length: 1229mm (48.43 in) - Flying weight: 3300-3400 gr - Wing area: 44.2 dm2 - Wing loading: 67g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationASSEMBLY AND OPERATION MANUAL
ASSEMBLY AND OPERATION MANUAL www.duratrax.com ITEMS INCLUDED The following items are included with your Vendetta Rally. Chassis Transmitter Body Decal Sheet Instruction Manual Exploded View/Parts Listing
More informationSPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER. Read entire instructions thoroughly before starting. INSTALLATION INSTRUCTIONS TOOLS REQUIRED:
Read entire instructions thoroughly before starting. TOOLS REQUIRED: SPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER INSTALLATION INSTRUCTIONS Complete socket set Phillips screwdriver Torx drivers Wire strippers/cutters
More informationConversion to Battery Power Del Tapparo
Conversion to Battery Power Del Tapparo Converting a track powered locomotive to battery power eliminates all of the electrical continuity problems associated with track power. However, the process of
More informationTP02C. 1:10 Scale Radio Controlled Electric Powered 2WD Racing Buggy. Dimensions. Length 410mm Width 250mm Height 150mm
TP02C 1:10 Scale Radio Controlled Electric Powered 2WD Racing Buggy Dimensions Length 410mm Width 250mm Height 150mm Transmitter Preparation Power Switch Antenna 27MHzTransmitter Crystal T 27MHz ON Extend
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CD CHANGER ATTACHMENT KIT 2004 CR-V AII 26118 Issue Date SEP 2003 PARTS LIST CD Changer Attachment Kit (sold separately): P/N 08B26-S9A-100
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1800mm (70.8 in) - Length: 1355mm (53.3 in) - Flying weight: 4100-4300 g - Wing area: 51 dm2 - Wing loading: 80g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationINSTALLATION INSTRUCTIONS
2806 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY -6 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This
More informationInstruction Manual book
book SPECIFICATION Wingspan : 2,080 mm 81.89 in. Length : 1,680 mm 66.14 in. Weight : 6.2 kg 13.64 Lbs. Radio : 06 channels. Servo : 06 servos. Engine : 30-35 CC Gas(FUJI IMVAC). Made in Vietnam. This
More information8mm EPP Acrocub. Instruction Manual. Specifications
8mm EPP Acrocub Instruction Manual Specifications Wingspan: 34.6 in (880mm) Length: 31.5 in (800mm) Wing Area: 213.9 sq in (13.8sq dm) Flying Weight: Approx. 9oz (270g) Dear Customer, www.valuehobby.com/8mm-epp-acrocub.html
More informationMain parts and accessories
Schemes : Main parts and accessories Contents : Removing the covering - 1 Horn installation - 3 Rudder installation - 4 Tail Wheel system - 12 Landing gear installation - 6 Stabilizer installation - 5
More information