COLD AIR SYSTEM. Installation Instructions for: Part Number Infiniti G35
|
|
- Virgil Hart
- 5 years ago
- Views:
Transcription
1 COLD AIR SYSTEM Installation Instructions for: Part Number Infiniti G35 ADVANCED ENGINE MANAGEMENT INC TH Street, Unit A Hawthorne, CA Phone: (310) Fax: (310) Instructions Part Number: Infiniti G35 VQ35DE 3.5L C.A.R.B. E.O. #D Infiniti G35 VQ35DE 3.5L C.A.R.B. E.O. #Pending Copyright 2003
2 Congratulations! You have just purchased the finest Air Induction & Filtration system for your car at any price! The AEM Cold Air Intake System is the result of extensive development on a wide variety of cars. It is the most advanced Cold Air Intake System on the market. Each system is specifically engineered for its application. All AEM Cold Air Intake Systems deliver maximum performance gains through lightweight, all-aluminum, mandrel-bent tubing that is tuned in both length and diameter. The aluminum will not crack in extended use like plastic. The tube length and diameter are matched for each specific engine to give power over a broad RPM range. Unlike plastic systems that use a continually diverging cross-section, we take advantage of the acoustical energy in the inlet duct to promote cylinder filling during the intake valve-opening event. Every intake is coated with a high-gloss, heat-reducing Zirconia based powder coating. This special blend of powder coating helps reduce heat penetration, which in turn reduces the temperature of the inlet air charge. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. The filter element has also been extensively developed. An integral part of all our filter elements is a built-in velocity stack. This velocity stack is specifically engineered to improve the aerodynamic efficiency of the intake system. We have seen airflow gains on a flow bench of 12-15% by using this velocity stack. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. Bill of Materials for: Upper intake pipe Lower intake pipe " air filter & Clamp BLO-5220 #52 Hose Clamp BLO-4820 #48 hose clamp " x 3" silicone Hose Nissan MAF adaptor BOLT,HEX M6 X 1 X WASHER, M6 ZINC-PLATED STEEL mm Nylok Nut Rubber Mount 1" x 6mm Washer, Flat M6x25x HOSE,ADAPTER 3.25/3.00 X 2.25" BLK Installation instructions S AEM Large Decal - Silver W AEM Lic Plate Frame - White E300 EMBLEM,CAS/SRS 3.00R
3 Read and understand these instructions BEFORE attempting to install this product. Note: This inlet pipe kit may require the removal and reinstallation of emissions related components. If you are not familiar with the installation and/or the operation of these components then please refer this installation to a qualified professional. This installation will also require access to the underside of the vehicle. If a lift is not available, jack up the front of the vehicle and support it with jack stands. Make sure vehicle is stable before working under it. 1) Getting started a) Make sure the vehicle is parked on a level surface and set parking brake. b) Remove left front wheel. c) Disconnect negative battery terminal. d) If engine has run within the past two hours let it cool down. e) Check contents of package with list on previous page f) Make sure AEM intake components are free of packaging material. 2) Removing the stock air inlet system a) Remove the four fasteners holding on the engine cover. Remove the engine cover. b) Remove the two plastic fasteners holding on the air duct and remove the duct from the engine bay. c) Loosen the hose clamp holding the stock intake tube on the throttle body. Loosen the spring hose clamp on the breather hose and pull the hose off of the fitting on the intake tube.
4 d) Remove the bolt holding the factory airbox in place. Unplug the Mass Air Flow (MAF) sensor and unsnap the wiring loom form the intake system. e) Pull directly upward on the airbox to unsnap it from the mounts. Remove the complete intake system from the car. FRONT f) From underneath the car, remove the bolts circled in the picture. g) From inside the wheel well, remove the two plastic fasteners shown in the picture. Fastener #1 h) Peel back the splash guard and tuck it out of the way. Remove the lower resonant chamber circled in the picture. i) Remove the air duct shown by removing the three plastic fasteners holding it in place. (see next page)
5 Fastener #2 Fastener #3 View Through Grille. View from underneath. Note: The G35 sedan has foam insert attached to the plastic duct. Remove the whole assembly. j) Remove the four bolts holding the MAF sensor on the factory airbox. Handle the MAF sensor with care. 3) Installing the AEM Cold Air Intake System When installing the Cold Air Intake System, DO NOT completely tighten the hose clamps or mounting tab hardware until instructed to do so later in these instructions. BER MOUNT CER a) Using the 6mm bolts and washers included in the kit, bolt the MAF sensor to the AEM adaptor. b) Slide one of the 3 straight silicone couplers over the MAF sensor as shown. Lightly oiling the inside of the coupler may help. Secure the coupler in place using a #48 hose clamp.
6 c) Place the reducing silicone coupler on the throttle body. Use a #52 hose clamp around the throttle body. Make sure the coupler is sitting squarely on the throttle body and tighten the #52 hose clamp. Loosely install a #48 hose clamp on the other end of the coupler. d) Insert the upper intake pipe in the coupler as shown. Reuse the factory hose clamp and install the breather hose on the fitting on the pipe. Do not tighten the #48 hose clamp. e) Install the assembly from step 3-b on the upper intake pipe. Loosely install a #48 hose clamp on the coupler. Make sure the MAF sensor connector is pointing toward the oil cap. f) Install the other 3 silicone coupler on the end of the AEM MAF adaptor. Loosely install two #48 hose clamps. g) Thread the rubber mount into the hole that held the resonant chamber rear mounting bolt. Hand tighten the rubber mount. h) If installing on a G35 Sedan, remove the mounting screw for the HID Headlight controller. Ignore step 3-h and 3-i if installing on a G35 Coupe.
7 NOTE i) Rotate the HID controller forward and reinstall the screw in the other mounting hole on the controller. Pull excess slack for the wires from farther up the harness if needed. j) Install the lower intake pipe in the end of the coupler on the AEM MAF adaptor. Line up the bracket on the pipe with the rubber mount and install the 6mm nylock nut and fender washer according to the diagram below. Do not tighten. Note: If a Bypass valve is to be used install it in the circled section of pipe. Bypass valve part number for this system is: S Nut Rubber Mount Fender Washer Support Bracket k) Install the AEM air filter on the end of the lower intake pipe. Make sure the filter is fully and squarely seated on the end of the pipe. Use a #52 hose clamp to secure it in place. l) Plug in the MAF senor. Place the engine cover on the intake manifold and check for clearance of the MAF sensor plug. Rotate the MAF sensor assembly until the plug has adequate clearance
8 For Technical Inquiries k) Position the intake system in such a way that no part touches the car when the engine is started and running. Check closely for clearance around the air filter and the AEM MAF sensor adaptor, reposition as needed. After proper positioning, tighten all the hose clamps and the nylock nut on the rubber mount. 4) Re-assemble the vehicle a) Re-attach the inner fender splash guard. b) Install the wheel and torque the lug nuts to factory recommendations. c) Install the engine cover. d) Check for any loose tools or fasteners e) Start the engine and perform a final inspection before driving. For Technical Inquiries Us at: tech@aempower.com
COLD AIR SYSTEM. Installation Instructions for: Part Number Nissan 350Z
COLD AIR SYSTEM Installation Instructions for: Part Number 21-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationSHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Honda Accord 4-Cyl. 2.4L Excluding LX-P Model
SHORT RAM INTAKE SYSTEM Installation Instructions for: Part Number 22-511 2003-2004 Honda Accord 4-Cyl. 2.4L Excluding LX-P Model ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.
More informationSHORT RAM AIR INTAKE SYSTEM. Installation Instructions for: Part Number Nissan 350Z
SHORT RAM AIR INTAKE SYSTEM Installation Instructions for: Part Number 22-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322
More informationBRUTE FORCE INTAKE SYSTEM
BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8105 1988-1993 Ford Mustang 5.0L MAF Only ADVANCED ENGINE MANAGEMENT INC. 2205
More informationADVANCED ENGINE MANAGEMENT INC.
COLD AIR SYSTEM Installation Instructions for: Part Number 21-474 2002-2005 Subaru Impreza WRX 2004-2005 Subaru Impreza WRX STi 2004-2005 Subaru Forester XT 2004-2005 Saab 92X ADVANCED ENGINE MANAGEMENT
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Nissan 240SX
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-441 1995-1998 Nissan 240SX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Honda Civic Si
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-516 2006 Honda Civic Si ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152
More informationSHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Dodge SRT-4 2.4L
SHORT RAM INTAKE SYSTEM Installation Instructions for: Part Number 22-425 2003-2005 Dodge SRT-4 2.4L ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-506 2002-2006 Acura RSX Type-S ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax:
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Mazda Miata
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-482 2000-2003 Mazda Miata ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationCOLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-486 2003-2003.5 MazdaSpeed Protégé 2.0L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Matrix XRS
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-466 2003 Toyota Matrix XRS ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Mazdaspeed Miata
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-489 2004 Mazdaspeed Miata ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Corolla & 2003 Toyota Matrix XR
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-469 2003-2004 Toyota Corolla & 2003 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Tacoma 4 Cyl Toyota 4Runner 4 Cyl.
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-463 1995-1999 Toyota Tacoma 4 Cyl. 1996-1999 Toyota 4Runner 4 Cyl. ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Honda Civic Si
COLD AIR SYSTEM Installation Instructions for: Part Number 21-508 2002-2004 Honda Civic Si ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationBrute Force Intake System. Installation Instructions for: Part Number Toyota 4Runner 3.4L V Toyota Tacoma 3.
Brute Force Intake System Installation Instructions for: Part Number 21-8402 1999-2002 Toyota 4Runner 3.4L V6 1999-2004 Toyota Tacoma 3.4L V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A
More informationCOLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number Mitsubishi Lancer Ralliart Manual Transmission Only
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-436 2004-2005 Mitsubishi Lancer Ralliart Manual Transmission Only ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne,
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Volkswagen Golf/GTI 1.8L Turbo Volkswagen Jetta 1.
COLD AIR SYSTEM Installation Instructions for: Part Number 21-493 1999.5-2004 Volkswagen Golf/GTI 1.8L Turbo 1999.5-2004 Volkswagen Jetta 1.8L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street,
More informationCOLD AIR INTAKE SYSTEM
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-433 2000-2004 Mitsubishi Eclipse RS & GS Congratulations! You have just purchased the finest Air Induction & Filtration system for your
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Ford Focus SVT
COLD AIR SYSTEM Installation Instructions for: Part Number 21-451 2002-2004 Ford Focus SVT ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationBRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required!
BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8103 96-04 Ford Mustang GT Excluding Bullet ADVANCED ENGINE MANAGEMENT INC. 2205
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Honda S2000
COLD AIR SYSTEM Installation Instructions for: Part Number 21-504 2000-2003 Honda S2000 Note: The installation of this Cold Air System requires the cutting or modification of plastic parts of the vehicle.
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Ford Focus ZX3
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-450 2000-2003 Ford Focus ZX3 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationBrute Force Intake System
Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8001 1992-1995 Chevy Trailblazer 5.7L V8 1988-1995 Chevy C/K Pickup 5.0L V8 1988-1995
More informationCOLD AIR INTAKE SYSTEM
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-475 2005-2006 Subaru Legacy 2.5L Turbo 2005-2006 Subaru Outback 2.5L Turbo Congratulations! You have just purchased the finest Air Induction
More informationBrute Force Intake System
Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required Installation Instructions for: Part Number 21-8013 2001-2004 Chevy Silverado 2500HD & 3500 2001-2004 GMC 2500HD & 3500 6.6L Duramax
More informationCOLD AIR INTAKE SYSTEM. Installation Instructions for: Part Numbers & Honda Civic EX M/T Honda Civic DX/LX M/T
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Numbers 21-500 & 21-502 2001-2005 Honda Civic EX M/T 2001-2005 Honda Civic DX/LX M/T ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit
More informationCOLD AIR INTAKE SYSTEM
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-549 2004-2006 Nissan Maxima SE/SL 3.5L V6 VQ35DE ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationBrute Force Intake System
Brute Force Intake System Installation Instructions for: Part Number: 21-8209 2005-06 Dodge Dakota 4.7L V8 2006 Mitsubishi Raider Durocross/XLS 4.7L V8 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street,
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Mazda RX-8 Instructions
COLD AIR SYSTEM Installation Instructions for: Part Number 21-485 2004-2009 Mazda RX-8 Instructions ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322
More informationBRUTE FORCE AIR INTAKE SYSTEM
BRUTE FORCE AIR INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8306 2005 Jeep Grand Cherokee 2006 Jeep Commander 5.7L V8 HEMI ADVANCED ENGINE
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-548 2003-2006 INFINITI G35 V6-3.5L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles
More informationCOLD AIR INTAKE SYSTEM
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-483 2003-2008 Mazda 6 s V6 DO NOT install a bypass valve on this intake! Congratulations! You have just purchased the finest Air Induction
More informationBRUTE FORCE INTAKE SYSTEM
BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8600 2006-2008 Honda Ridgeline 3.5L V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126
More informationBrute Force Intake System
Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8005 1996-2004 Chevy Blazer 4.3L V6 1996-2004 Chevy S10 4.3L V6 1996-2003 Chevy
More informationHYBRID INTAKE SYSTEM
HYBRID INTAKE SYSTEM Installation Instructions for: Part Number 21-5002 1988-1991 Honda Civic/CRX w/ B18C1 *Legal in California only for racing vehicles which may never be used upon a highway. ADVANCED
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Hyundai Tiburon V6
COLD AIR SYSTEM Installation Instructions for: Part Number 21-521 2003-2005 Hyundai Tiburon V6 ATTENTION: This installation procedure requires some body modifications and may require the use of specialized
More informationADVANCED ENGINE MANAGEMENT INC.
COLD AIR SYSTEM Installation Instructions for: Part Number 21-432 2001-2003 Chrysler Sebring Coupe Lxi 2001-2003 Dodge Stratus Coupe R/T 2000-2004 Mitsubishi Eclipse GT ADVANCED ENGINE MANAGEMENT INC.
More informationCOLD AIR INTAKE SYSTEM
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-488 2004-2008 Mazda 3 s 2.3L 4cyl Congratulations! You have just purchased the finest Air Induction & Filtration system for your car
More informationBRUTE FORCE AIR INTAKE SYSTEM
BRUTE FORCE AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-8108 1997-2000 Ford Ranger 4.0L V6 With O.E. panel style air filter ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit
More informationBRUTE FORCE AIR INTAKE SYSTEM
BRUTE FORCE AIR INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8206 Dodge Ram 2500,3500 5.9L Turbo Diesel I6 2003-2005 ADVANCED ENGINE MANAGEMENT
More informationYou can purchase this part at: COLD AIR SYSTEM
COLD AIR SYSTEM Installation Instructions for: Part Number 21-450 2000-2003 Ford Focus 2.0L Zetec ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax:
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Honda Prelude
COLD AIR SYSTEM Installation Instructions for: Part Number 21-406 1997-2001 Honda Prelude ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Civic CX/DX/LX
COLD AIR SYSTEM Installation Instructions for: Part Number 21-413 1996-2000 Civic CX/DX/LX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationCOLD AIR INTAKE SYSTEM
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-491 2005-2008 Mazda 6i 2.3L NON-PZEV Do not install a bypass valve on this intake system! ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR
COLD AIR SYSTEM Installation Instructions for: Part Number 21-469 2003-2004 Toyota Corolla 2002-2004 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S
COLD AIR SYSTEM Installation Instructions for: Part Number 21-506 2002-2005 Acura RSX Type-S ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationCOLD AIR INTAKE SYSTEM
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-507 2002-2006 Acura RSX AT Inline 4, Automatic Transmission ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.
More informationADVANCED ENGINE MANAGEMENT INC.
COLD AIR SYSTEM Installation Instructions for: Part Number 21-493 1999.5-2005 Volkswagen GTI 1.8L 1999.5-2006 Volkswagen Golf 1.9L Turbo Diesel 1999.5 2005.5 Volkswagen Jetta 1.8L Turbo & 1.9L Turbo Diesel
More informationV2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra RS/LS
V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6003 1994-2001 Acura Integra RS/LS ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationV2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra GS-R
V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6004 1994-2001 Acura Integra GS-R ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationV2 INTAKE SYSTEM. Patent No. 6,959,679
V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6016 1998-2002 Honda Accord V6 2001-2003 Acura CL V6 2000-2003 Acura TL V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH
More informationV2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Honda Prelude
V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6005 1992-2001 Honda Prelude ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310)
More informationV2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Honda S2000
V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6104 2000-2005 Honda S2000 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310)
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles
More informationV2 INTAKE SYSTEM. Installation Instructions for: Part Number Acura RSX
V2 INTAKE SYSTEM Installation Instructions for: Part Number 24-6105 2002-2003 Acura RSX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-573 2006-2008 Toyota Yaris 1.5L *Legal in California only for racing vehicles which may never be used upon a highway. 2008, Advanced
More informationKit Part Number:
10-677 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-677 Nissan 350Z 3.5L V6 2007-2008 CARB EO # D-392-30 Short Ram Intake Systems that are pending an Executive Order number (EO#)
More information2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670. Will not fit MAF Sensor Equipped Vehicles
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-511 2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670 2003 HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670 Will not
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-568 2005-2006 Scion TC 2.4L *Legal in California only for racing vehicles which may never be used upon a highway. 2009, Advanced Engine
More informationKit Part Number:
10-8218 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8218 2007 Dodge Nitro 3.7L V6 CARB EO # D392-30 Brute Force Intake Systems that are pending an Executive Order number (EO#)
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-8502 2004-2009 Nissan Titan 5.6L V8 2004-2009 Nissan Armada 5.6LV8 2004-2009 Infiniti QX56 5.6L V8 C.A.R.B. E.O. D-392-33 C.A.R.B.
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8500 2001-2003 NISSAN Frontier V6-3.3L C.A.R.B. E.O. # D-670 2001-2003 NISSAN Xterra V6-3.3L C.A.R.B. E.O. #
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-682 2008 Chevrolet Cobalt SS CARB EO - D-392-32 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-488 2006-2008 MAZDA 3 L4 2.3L SEE * NOTE 2004-2008 MAZDA 3 L4 2.0L SEE * NOTE 2004-2005 MAZDA 3 L4 2.3L C.A.R.B.
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2007-2008 Mazda Mazdaspeed 3 CARB EO # D-392-30 Cold Air Intake Systems that are pending an Executive Order number (EO#) relating to exemptions
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1.
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-799C (GUN METAL GRAY FINISH) 2014-16 NISSAN SENTRA 1.8L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157D AIR
More informationBill of Materials for
Bill of Materials for 77060012 1 2-P5153572 Inlet Pipe 1 21-202M 2.75" Filter 1 103-BLO-4820N Filter Hose Clamp 1 559999 Washer, Fender M6x25 1 1-3028 Washer, 1/4 SAE Flat 1 1-2072 Bolt, 1/4-20-UNC x 1
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8214 2006 Dodge Ram 3.7L V6 CARB EO # D-392-29. 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine
More informationEquipped with AEM Dryflow Filter No Oil Required!
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6001 1992-1995 HONDA Civic SI L4-1.6L C.A.R.B. E.O. # D-670 1992-1995 HONDA Civic LX L4-1.5L Manual Trans. C.A.R.B.
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8402 1999-2004 TOYOTA Tacoma V6-3.4L C.A.R.B. E.O. # D-670 1999-2002 TOYOTA 4Runner V6-3.4L C.A.R.B. E.O. # D-670
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-544 2002-2006 NISSAN Sentra SE-R Spec-V L4-2.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6004 1994-2001 ACURA Integra GSR L4-1.8L C.A.R.B. E.O. # D-670 AEM bypass valves are not compatible with this
More informationAEM bypass valves are not compatible with this intake system (part number ) DO NOT attempt to install an AEM bypass valve on this intake system!
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-452 2005 FORD Focus L4-2.0L SEE * NOTE 2004 FORD Focus L4-2.3L SEE * NOTE AEM bypass valves are not compatible
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 41-1406 2006-2013 LEXUS IS250 V6-2.5L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-463 1997-1999 TOYOTA Tacoma L4-2.7L C.A.R.B. E.O. # D-392-18 1997-1999 TOYOTA Tacoma L4-2.4L C.A.R.B. E.O. #
More informationEquipped with AEM Dryflow Filter No Oil Required!
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-491B (Blue Finish) 21-491C (Gun Metal Grey Finish) 21-491P (Vacuum Metalized Chrome-VMC) 21-491R (Red Finish)
More informationINSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1.
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-799C (GUN METAL GRAY FINISH) 2014-16 NISSAN SENTRA 1.8L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157D AIR
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:22-516 2006-2007 HONDA Civic Si L4-2.0L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles
More information21-413B (Blue Finish) C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome-VMC) R (Red Finish)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-413B (Blue Finish) 21-413C (Gun Metal Grey Finish) 21-413P (Vacuum Metalized Chrome-VMC) 21-413R (Red Finish)
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:41-1403 2010-2011 TOYOTA Corolla L4-1.8L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER DS (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-823DS (GUN METAL GRAY FINISH) 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-202DOSK AIR FILTER; OFFSET 2.75" X
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-641 2006 MAZDA Mazdaspeed 6 L4-2.3L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8306 2006 JEEP Commander V8-5.7L C.A.R.B. E.O. # D-670 2005-2006 JEEP Grand Cherokee V8-5.7L C.A.R.B. E.O. #
More informationLEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED OR LICENSED FOR USE UPON A HIGHWAY.
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8408 2010-2013 TOYOTA Tundra V8-4.6L 2007-2014 TOYOTA Tundra V8-5.7L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2004.5-2005 Chevy/GMC 6.6L Duramax Diesel LLY CARB EO # D-392-29 8th # in the VIN is 2 on 2004 models. 2009, Advanced Engine Management,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PART NUMBER: 21-426B (Blue Finish) 21-426P (Vacuum Metalized Chrome-VMC) 21-426R (Red Finish) 2003-2005 DODGE Neon SRT-4 L4-2.4L Turbo C.A.R.B. E.O. # D-670-15 Part Number 21-426
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-474 2007 SUBARU Impreza WRX STi H4-2.5L SEE * NOTE 2004-2006 SUBARU Impreza WRX STi H4-2.5L C.A.R.B. E.O. # D-670
More informationPART NUMBER: B (Blue Finish) C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome-VMC) R (Red Finish)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-403B (Blue Finish) 21-403C (Gun Metal Grey Finish) 21-403P (Vacuum Metalized Chrome-VMC) 21-403R (Red Finish)
More informationPART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8020 2006 PONTIAC GTO V8-6.0L SEE * NOTE 2005 PONTIAC GTO V8-6.0L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California
More informationEquipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number:
Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 1999-2001 Ford F-350 6.8L V10 CARB EO # D-392-30 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8207 2005 DODGE Durango V8-5.7L See * NOTE 2004 DODGE Durango V8-5.7L C.A.R.B. E.O. # D-670 * NOTE: Legal in
More informationKit Part Number:
Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2008 Mitsubishi Lancer Evolution X CARB EO #: Pending AEM Cold Air Intake Systems that are pending an Executive Order number (EO#) relating
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-450B (Blue Finish) 21-450C (Gun Metal Grey Finish) 21-450P (Vacuum Metalized Chrome-VMC) 21-450R (Red Finish)
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-818C (GUN METAL GRAY FINISH) 2017 Nissan Sentra SR Turbo 1.6T 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157DK
More informationINSTALLATION INSTRUCTION PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTION PART NUMBER: 24-6003 1994-2001 ACURA Integra L4-1.8L Manual Trans. C.A.R.B. E.O. # D-670 Non VTEC models ONLY AEM bypass valves
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-474 2006-2007 SUBARU Impreza WRX H4-2.5L C.A.R.B. E.O. # D-670-6 2004-2007 SUBARU Impreza WRX STi H4-2.5L C.A.R.B.
More information