COLD AIR SYSTEM. Installation Instructions for: Part Number Nissan 350Z

Size: px
Start display at page:

Download "COLD AIR SYSTEM. Installation Instructions for: Part Number Nissan 350Z"

Transcription

1 COLD AIR SYSTEM Installation Instructions for: Part Number Nissan 350Z ADVANCED ENGINE MANAGEMENT INC TH Street, Unit A Hawthorne, CA Phone: (310) Fax: (310) Instructions Part Number: Nissan 350Z VQ35DE C.A.R.B. E.O. #D Nissan 350Z VQ5DE C.A.R.B. E.O.#D Nissan 350Z VQ5DE C.A.R.B. E.O.#Pending 2006 Nissan 350Z VQ5DE C.A.R.B. E.O.#Pending Copyright 2003

2 Congratulations! You have just purchased the finest Air Induction & Filtration system for your car at any price! The AEM Cold Air Intake System is the result of extensive development on a wide variety of cars. It is the most advanced Cold Air Intake System on the market. Each system is specifically engineered for its application. All AEM Cold Air Intake Systems deliver maximum performance gains through lightweight, all-aluminum, mandrel-bent tubing that is tuned in both length and diameter. The aluminum will not crack in extended use like plastic. The tube length and diameter are matched for each specific engine to give power over a broad RPM range. Unlike plastic systems that use a continually diverging cross-section, we take advantage of the acoustical energy in the inlet duct to promote cylinder filling during the intake valve-opening event. Every intake is coated with a high-gloss, heat-reducing Zirconia based powder coating. This special blend of powder coating helps reduce heat penetration, which in turn reduces the temperature of the inlet air charge. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. The filter element has also been extensively developed. An integral part of all our filter elements is a built-in velocity stack. This velocity stack is specifically engineered to improve the aerodynamic efficiency of the intake system. We have seen airflow gains on a flow bench of 12-15% by using this velocity stack. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. Bill of Materials for: Quantity Part Number Description * UPPER INTAKE PIPE * LOWER INTAKE PIPE NISSAN MAF SENSOR ADAPTOR HOSE,ADAPTER 3.25/3.00 X 2.25" BLK HOSE,SILICONE 3.00X3" AEM BLK BLO-4820 HOSE CLAMP, " BLO-5220 HOSE CLAMP, " Washer, Flat M6x25x Nut, Nylock 6mm Mount, Rubber 1" BOLT,HEX M6 X 1 X WASHER, M6 ZINC-PLATED STEEL SPACER,.625OD X.295 ID X BOLT,FLAT HD M8 X NUT,NYLOK 8MM * Wiring Harness Bracket AIR FILTER ASMBLY 3.0 5" & Clamp * Installation Instructions E EMBLEM,CAS/SRS W License Plate Frame Warning Decal EO Decal S Regular AEM Sticker

3 Read and understand these instructions BEFORE attempting to install this product. Note: This inlet pipe kit may require the removal and reinstallation of emissions related components. If you are not familiar with the installation and/or the operation of these components then please refer this installation to a qualified professional. This installation will also require access to the underside of the vehicle. If a lift is not available, jack up the front of the vehicle and support it with jack stands. Make sure vehicle is stable before working under it. 1) Getting started a) Make sure vehicle is parked on a level surface. b) Set parking brake. c) Disconnect negative battery terminal. d) If engine has run within the past two hours let it cool down. 2) Removing the stock air inlet system a) Remove the fasteners holding the strut tower bar in place from both sides. Unclip the electrical wiring loom connections and remove the bar from the engine bay. b) Loosen the hose clamps shown in the picture. Unplug the Mass Air Flow (MAF) sensor and detach the MAF wiring harness from the sensor. c) Pop out and remove the plastic fastener on the front air duct. Unsnap the duct and slide it forward. Remove the bolt circled in the diagram.

4 d) From the underside of the intake tube, detach the breather hose then remove the intake tube from the engine bay. e) Remove the bolt holding the air filter housing assembly in place. f) Gently pull directly upward on the air filter housing assembly until it unsnaps from its mounts and remove it from the engine bay. g) Unsnap the wiring loom fasteners from the inner fender. h) Looking where the factory air filter housing was, pull the wheel speed sensor plug shown in the picture from its mount. Do not unplug the sensor. i) Remove the A/C line bracket bolt shown in the picture.

5 FRONT j) Remove the MAF sensor from the air filter assembly by removing the four mounting bolts. k) From the underside of the car, remove the bolts shown in the picture. l) Pull down on the splash guard to reveal two plastic fasteners. Remove these fasteners. m) It is now possible to gain access to the area behind the front bumper. This is where the air filter will be located. 3) Installing the AEM Cold Air Intake System When installing the Cold Air Intake System, DO NOT completely tighten the hose clamps or mounting tab hardware until instructed to do so later in these instructions. RUBBER MOUNT a) Install the rubber mount into the hole for the A/C line bracket bolt. Use the included spacer underneath the rubber mount to space it upward to clear the bracket. Tighten by hand. SPACER

6 b) Attach the breather hose to the fitting in the AEM upper intake pipe (the shorter one in the kit). Put the 3 ¼ to 3.0 silicone reducer on the end of the pipe closest to the bend. Place the 3 ¼ side of the silicone coupler over the throttle body. c) Using the four bolts and washers included in the kit, attach the AEM MAF adaptor to the Nissan MAF sensor. d) Place the 3 silicone coupler around the MAF sensor, not the AEM MAF adaptor, and insert onto the upper intake pipe. Use the #52 hose clamp around the throttle body and the #48 hose clamps for the 3 diameter tubing. Do not tighten the hose clamps. e) Install the 8mm bolt and washer included in the kit into the hole from the removed bolt from step C of the previous section. Attach the AEM wiring harness bracket to the bolt on the underside and secure it in place with the included 8mm Nylok nut. f) Snap the factory wiring harness into the bracket as shown. Insert the other plastic wiring loom holder into the hole from the bolt removed in step E of the previous section.

7 g) Inside the cavity behind the bumper, unsnap the wiring loom from the body. h) Tuck the wiring up and out of the way. i) Install the air filter on the end of the lower intake pipe closest to the 7/8 hole. Install the recessed plastic plug in the hole if not done so already. j) Install the 3 coupler and two #48 hose clamps on the end of the MAF adaptor. Insert the upper end of the lower intake pipe into the coupler. Nut Rubber Mount Fender Washer Support Bracket i) Line up the tab on the intake pipe with the rubber mount. Run the wheel speed sensor wire underneath intake pipe support tab. Make sure the plug and wire not in a place where they will be pinched or damaged. Install the nut and washer according to the diagram at right.

8 j) Position the pipes and filter in such a way that no part of them touch the vehicle or the plastic fender liner. Make sure the intake does not come into contact with any of the adjacent A/C hard-lines. Contact may result in failure of the A/C system and costly repairs. After they have been positioned correctly, tighten all hose clamps and the mounting tab hardware. Plug in the MAF sensor and re-install the strut-tower bar. Re-install the splash-guard and fender liner. Re-connect the battery and start the engine. Perform a final inspection before driving. Note: If an AEM air bypass valve is to be used, install it in the section of pipe circled in the diagram above. For Technical Inquiries Us At tech@aempower.com

COLD AIR SYSTEM. Installation Instructions for: Part Number Infiniti G35

COLD AIR SYSTEM. Installation Instructions for: Part Number Infiniti G35 COLD AIR SYSTEM Installation Instructions for: Part Number 21-548 2003-2005 Infiniti G35 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

SHORT RAM AIR INTAKE SYSTEM. Installation Instructions for: Part Number Nissan 350Z

SHORT RAM AIR INTAKE SYSTEM. Installation Instructions for: Part Number Nissan 350Z SHORT RAM AIR INTAKE SYSTEM Installation Instructions for: Part Number 22-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Honda Accord 4-Cyl. 2.4L Excluding LX-P Model

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Honda Accord 4-Cyl. 2.4L Excluding LX-P Model SHORT RAM INTAKE SYSTEM Installation Instructions for: Part Number 22-511 2003-2004 Honda Accord 4-Cyl. 2.4L Excluding LX-P Model ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.

More information

BRUTE FORCE INTAKE SYSTEM

BRUTE FORCE INTAKE SYSTEM BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8105 1988-1993 Ford Mustang 5.0L MAF Only ADVANCED ENGINE MANAGEMENT INC. 2205

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Nissan 240SX

SHORT RAM SYSTEM. Installation Instructions for: Part Number Nissan 240SX SHORT RAM SYSTEM Installation Instructions for: Part Number 22-441 1995-1998 Nissan 240SX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Dodge SRT-4 2.4L

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Dodge SRT-4 2.4L SHORT RAM INTAKE SYSTEM Installation Instructions for: Part Number 22-425 2003-2005 Dodge SRT-4 2.4L ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S

SHORT RAM SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S SHORT RAM SYSTEM Installation Instructions for: Part Number 22-506 2002-2006 Acura RSX Type-S ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax:

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Honda Civic Si

SHORT RAM SYSTEM. Installation Instructions for: Part Number Honda Civic Si SHORT RAM SYSTEM Installation Instructions for: Part Number 22-516 2006 Honda Civic Si ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152

More information

ADVANCED ENGINE MANAGEMENT INC.

ADVANCED ENGINE MANAGEMENT INC. COLD AIR SYSTEM Installation Instructions for: Part Number 21-474 2002-2005 Subaru Impreza WRX 2004-2005 Subaru Impreza WRX STi 2004-2005 Subaru Forester XT 2004-2005 Saab 92X ADVANCED ENGINE MANAGEMENT

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-486 2003-2003.5 MazdaSpeed Protégé 2.0L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Civic Si

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Civic Si COLD AIR SYSTEM Installation Instructions for: Part Number 21-508 2002-2004 Honda Civic Si ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Corolla & 2003 Toyota Matrix XR

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Corolla & 2003 Toyota Matrix XR SHORT RAM SYSTEM Installation Instructions for: Part Number 22-469 2003-2004 Toyota Corolla & 2003 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazdaspeed Miata

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazdaspeed Miata SHORT RAM SYSTEM Installation Instructions for: Part Number 22-489 2004 Mazdaspeed Miata ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Matrix XRS

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Matrix XRS SHORT RAM SYSTEM Installation Instructions for: Part Number 22-466 2003 Toyota Matrix XRS ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number Mitsubishi Lancer Ralliart Manual Transmission Only

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number Mitsubishi Lancer Ralliart Manual Transmission Only COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-436 2004-2005 Mitsubishi Lancer Ralliart Manual Transmission Only ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne,

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Tacoma 4 Cyl Toyota 4Runner 4 Cyl.

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Tacoma 4 Cyl Toyota 4Runner 4 Cyl. SHORT RAM SYSTEM Installation Instructions for: Part Number 22-463 1995-1999 Toyota Tacoma 4 Cyl. 1996-1999 Toyota 4Runner 4 Cyl. ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazda Miata

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazda Miata SHORT RAM SYSTEM Installation Instructions for: Part Number 22-482 2000-2003 Mazda Miata ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Volkswagen Golf/GTI 1.8L Turbo Volkswagen Jetta 1.

COLD AIR SYSTEM. Installation Instructions for: Part Number Volkswagen Golf/GTI 1.8L Turbo Volkswagen Jetta 1. COLD AIR SYSTEM Installation Instructions for: Part Number 21-493 1999.5-2004 Volkswagen Golf/GTI 1.8L Turbo 1999.5-2004 Volkswagen Jetta 1.8L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street,

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Mazda RX-8 Instructions

COLD AIR SYSTEM. Installation Instructions for: Part Number Mazda RX-8 Instructions COLD AIR SYSTEM Installation Instructions for: Part Number 21-485 2004-2009 Mazda RX-8 Instructions ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

Brute Force Intake System. Installation Instructions for: Part Number Toyota 4Runner 3.4L V Toyota Tacoma 3.

Brute Force Intake System. Installation Instructions for: Part Number Toyota 4Runner 3.4L V Toyota Tacoma 3. Brute Force Intake System Installation Instructions for: Part Number 21-8402 1999-2002 Toyota 4Runner 3.4L V6 1999-2004 Toyota Tacoma 3.4L V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-549 2004-2006 Nissan Maxima SE/SL 3.5L V6 VQ35DE ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-488 2004-2008 Mazda 3 s 2.3L 4cyl Congratulations! You have just purchased the finest Air Induction & Filtration system for your car

More information

BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required!

BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8103 96-04 Ford Mustang GT Excluding Bullet ADVANCED ENGINE MANAGEMENT INC. 2205

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Ford Focus ZX3

SHORT RAM SYSTEM. Installation Instructions for: Part Number Ford Focus ZX3 SHORT RAM SYSTEM Installation Instructions for: Part Number 22-450 2000-2003 Ford Focus ZX3 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Ford Focus SVT

COLD AIR SYSTEM. Installation Instructions for: Part Number Ford Focus SVT COLD AIR SYSTEM Installation Instructions for: Part Number 21-451 2002-2004 Ford Focus SVT ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Installation Instructions for: Part Number: 21-8209 2005-06 Dodge Dakota 4.7L V8 2006 Mitsubishi Raider Durocross/XLS 4.7L V8 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street,

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-433 2000-2004 Mitsubishi Eclipse RS & GS Congratulations! You have just purchased the finest Air Induction & Filtration system for your

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required Installation Instructions for: Part Number 21-8013 2001-2004 Chevy Silverado 2500HD & 3500 2001-2004 GMC 2500HD & 3500 6.6L Duramax

More information

BRUTE FORCE INTAKE SYSTEM

BRUTE FORCE INTAKE SYSTEM BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8600 2006-2008 Honda Ridgeline 3.5L V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda S2000

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda S2000 COLD AIR SYSTEM Installation Instructions for: Part Number 21-504 2000-2003 Honda S2000 Note: The installation of this Cold Air System requires the cutting or modification of plastic parts of the vehicle.

More information

BRUTE FORCE AIR INTAKE SYSTEM

BRUTE FORCE AIR INTAKE SYSTEM BRUTE FORCE AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-8108 1997-2000 Ford Ranger 4.0L V6 With O.E. panel style air filter ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-475 2005-2006 Subaru Legacy 2.5L Turbo 2005-2006 Subaru Outback 2.5L Turbo Congratulations! You have just purchased the finest Air Induction

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Numbers & Honda Civic EX M/T Honda Civic DX/LX M/T

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Numbers & Honda Civic EX M/T Honda Civic DX/LX M/T COLD AIR INTAKE SYSTEM Installation Instructions for: Part Numbers 21-500 & 21-502 2001-2005 Honda Civic EX M/T 2001-2005 Honda Civic DX/LX M/T ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8001 1992-1995 Chevy Trailblazer 5.7L V8 1988-1995 Chevy C/K Pickup 5.0L V8 1988-1995

More information

BRUTE FORCE AIR INTAKE SYSTEM

BRUTE FORCE AIR INTAKE SYSTEM BRUTE FORCE AIR INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8306 2005 Jeep Grand Cherokee 2006 Jeep Commander 5.7L V8 HEMI ADVANCED ENGINE

More information

BRUTE FORCE AIR INTAKE SYSTEM

BRUTE FORCE AIR INTAKE SYSTEM BRUTE FORCE AIR INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8206 Dodge Ram 2500,3500 5.9L Turbo Diesel I6 2003-2005 ADVANCED ENGINE MANAGEMENT

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S

COLD AIR SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S COLD AIR SYSTEM Installation Instructions for: Part Number 21-506 2002-2005 Acura RSX Type-S ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8005 1996-2004 Chevy Blazer 4.3L V6 1996-2004 Chevy S10 4.3L V6 1996-2003 Chevy

More information

You can purchase this part at: COLD AIR SYSTEM

You can purchase this part at:   COLD AIR SYSTEM COLD AIR SYSTEM Installation Instructions for: Part Number 21-450 2000-2003 Ford Focus 2.0L Zetec ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax:

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-483 2003-2008 Mazda 6 s V6 DO NOT install a bypass valve on this intake! Congratulations! You have just purchased the finest Air Induction

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Civic CX/DX/LX

COLD AIR SYSTEM. Installation Instructions for: Part Number Civic CX/DX/LX COLD AIR SYSTEM Installation Instructions for: Part Number 21-413 1996-2000 Civic CX/DX/LX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

ADVANCED ENGINE MANAGEMENT INC.

ADVANCED ENGINE MANAGEMENT INC. COLD AIR SYSTEM Installation Instructions for: Part Number 21-432 2001-2003 Chrysler Sebring Coupe Lxi 2001-2003 Dodge Stratus Coupe R/T 2000-2004 Mitsubishi Eclipse GT ADVANCED ENGINE MANAGEMENT INC.

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR

COLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR COLD AIR SYSTEM Installation Instructions for: Part Number 21-469 2003-2004 Toyota Corolla 2002-2004 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-491 2005-2008 Mazda 6i 2.3L NON-PZEV Do not install a bypass valve on this intake system! ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH

More information

HYBRID INTAKE SYSTEM

HYBRID INTAKE SYSTEM HYBRID INTAKE SYSTEM Installation Instructions for: Part Number 21-5002 1988-1991 Honda Civic/CRX w/ B18C1 *Legal in California only for racing vehicles which may never be used upon a highway. ADVANCED

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Hyundai Tiburon V6

COLD AIR SYSTEM. Installation Instructions for: Part Number Hyundai Tiburon V6 COLD AIR SYSTEM Installation Instructions for: Part Number 21-521 2003-2005 Hyundai Tiburon V6 ATTENTION: This installation procedure requires some body modifications and may require the use of specialized

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-507 2002-2006 Acura RSX AT Inline 4, Automatic Transmission ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Prelude

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Prelude COLD AIR SYSTEM Installation Instructions for: Part Number 21-406 1997-2001 Honda Prelude ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra GS-R

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra GS-R V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6004 1994-2001 Acura Integra GS-R ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra RS/LS

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra RS/LS V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6003 1994-2001 Acura Integra RS/LS ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

ADVANCED ENGINE MANAGEMENT INC.

ADVANCED ENGINE MANAGEMENT INC. COLD AIR SYSTEM Installation Instructions for: Part Number 21-493 1999.5-2005 Volkswagen GTI 1.8L 1999.5-2006 Volkswagen Golf 1.9L Turbo Diesel 1999.5 2005.5 Volkswagen Jetta 1.8L Turbo & 1.9L Turbo Diesel

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Honda S2000

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Honda S2000 V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6104 2000-2005 Honda S2000 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310)

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679

V2 INTAKE SYSTEM. Patent No. 6,959,679 V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6016 1998-2002 Honda Accord V6 2001-2003 Acura CL V6 2000-2003 Acura TL V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Honda Prelude

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Honda Prelude V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6005 1992-2001 Honda Prelude ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310)

More information

V2 INTAKE SYSTEM. Installation Instructions for: Part Number Acura RSX

V2 INTAKE SYSTEM. Installation Instructions for: Part Number Acura RSX V2 INTAKE SYSTEM Installation Instructions for: Part Number 24-6105 2002-2003 Acura RSX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

Kit Part Number:

Kit Part Number: 10-677 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-677 Nissan 350Z 3.5L V6 2007-2008 CARB EO # D-392-30 Short Ram Intake Systems that are pending an Executive Order number (EO#)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-573 2006-2008 Toyota Yaris 1.5L *Legal in California only for racing vehicles which may never be used upon a highway. 2008, Advanced

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-548 2003-2006 INFINITI G35 V6-3.5L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-8502 2004-2009 Nissan Titan 5.6L V8 2004-2009 Nissan Armada 5.6LV8 2004-2009 Infiniti QX56 5.6L V8 C.A.R.B. E.O. D-392-33 C.A.R.B.

More information

2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670. Will not fit MAF Sensor Equipped Vehicles

2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670. Will not fit MAF Sensor Equipped Vehicles Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-511 2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670 2003 HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670 Will not

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-568 2005-2006 Scion TC 2.4L *Legal in California only for racing vehicles which may never be used upon a highway. 2009, Advanced Engine

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-488 2006-2008 MAZDA 3 L4 2.3L SEE * NOTE 2004-2008 MAZDA 3 L4 2.0L SEE * NOTE 2004-2005 MAZDA 3 L4 2.3L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8500 2001-2003 NISSAN Frontier V6-3.3L C.A.R.B. E.O. # D-670 2001-2003 NISSAN Xterra V6-3.3L C.A.R.B. E.O. #

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2007-2008 Mazda Mazdaspeed 3 CARB EO # D-392-30 Cold Air Intake Systems that are pending an Executive Order number (EO#) relating to exemptions

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1.

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1. Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-799C (GUN METAL GRAY FINISH) 2014-16 NISSAN SENTRA 1.8L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157D AIR

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6004 1994-2001 ACURA Integra GSR L4-1.8L C.A.R.B. E.O. # D-670 AEM bypass valves are not compatible with this

More information

Kit Part Number:

Kit Part Number: 10-8218 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8218 2007 Dodge Nitro 3.7L V6 CARB EO # D392-30 Brute Force Intake Systems that are pending an Executive Order number (EO#)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8214 2006 Dodge Ram 3.7L V6 CARB EO # D-392-29. 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine

More information

Equipped with AEM Dryflow Filter No Oil Required!

Equipped with AEM Dryflow Filter No Oil Required! Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6001 1992-1995 HONDA Civic SI L4-1.6L C.A.R.B. E.O. # D-670 1992-1995 HONDA Civic LX L4-1.5L Manual Trans. C.A.R.B.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-450B (Blue Finish) 21-450C (Gun Metal Grey Finish) 21-450P (Vacuum Metalized Chrome-VMC) 21-450R (Red Finish)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-682 2008 Chevrolet Cobalt SS CARB EO - D-392-32 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-518B (Blue Finish) 21-518C (Gun Metal Grey Finish) 21-518P (Vacuum Metalized Chrome-VMC) 21-518R (Red Finish)

More information

PART NUMBER:

PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8020 2006 PONTIAC GTO V8-6.0L SEE * NOTE 2005 PONTIAC GTO V8-6.0L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California

More information

Bill of Materials for

Bill of Materials for Bill of Materials for 77060012 1 2-P5153572 Inlet Pipe 1 21-202M 2.75" Filter 1 103-BLO-4820N Filter Hose Clamp 1 559999 Washer, Fender M6x25 1 1-3028 Washer, 1/4 SAE Flat 1 1-2072 Bolt, 1/4-20-UNC x 1

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-544 2002-2006 NISSAN Sentra SE-R Spec-V L4-2.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing

More information

INSTALLATION INSTRUCTION PART NUMBER:

INSTALLATION INSTRUCTION PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTION PART NUMBER: 24-6003 1994-2001 ACURA Integra L4-1.8L Manual Trans. C.A.R.B. E.O. # D-670 Non VTEC models ONLY AEM bypass valves

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS PART NUMBER: 21-426B (Blue Finish) 21-426P (Vacuum Metalized Chrome-VMC) 21-426R (Red Finish) 2003-2005 DODGE Neon SRT-4 L4-2.4L Turbo C.A.R.B. E.O. # D-670-15 Part Number 21-426

More information

21-413B (Blue Finish) C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome-VMC) R (Red Finish)

21-413B (Blue Finish) C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome-VMC) R (Red Finish) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-413B (Blue Finish) 21-413C (Gun Metal Grey Finish) 21-413P (Vacuum Metalized Chrome-VMC) 21-413R (Red Finish)

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1.

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1. Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-799C (GUN METAL GRAY FINISH) 2014-16 NISSAN SENTRA 1.8L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157D AIR

More information

PART NUMBER: B (Blue Finish) C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome-VMC) R (Red Finish)

PART NUMBER: B (Blue Finish) C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome-VMC) R (Red Finish) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-403B (Blue Finish) 21-403C (Gun Metal Grey Finish) 21-403P (Vacuum Metalized Chrome-VMC) 21-403R (Red Finish)

More information

PART NUMBER: MAZDA MX-5 L4-2.0L C.A.R.B. E.O. # D MAZDA MX-5 Miata L4-2.0L C.A.R.B. E.O. # D-670-6

PART NUMBER: MAZDA MX-5 L4-2.0L C.A.R.B. E.O. # D MAZDA MX-5 Miata L4-2.0L C.A.R.B. E.O. # D-670-6 Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-640 2006-2008 MAZDA MX-5 L4-2.0L C.A.R.B. E.O. # D-670-6 2006-2009 MAZDA MX-5 Miata L4-2.0L C.A.R.B. E.O. # D-670-6

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-450B (Blue Finish) 21-450C (Gun Metal Grey Finish) 21-450P (Vacuum Metalized Chrome-VMC) 21-450R (Red Finish)

More information

LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED OR LICENSED FOR USE UPON A HIGHWAY.

LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED OR LICENSED FOR USE UPON A HIGHWAY. Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8408 2010-2013 TOYOTA Tundra V8-4.6L 2007-2014 TOYOTA Tundra V8-5.7L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES

More information

Equipped with AEM Dryflow Filter No Oil Required!

Equipped with AEM Dryflow Filter No Oil Required! Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-491B (Blue Finish) 21-491C (Gun Metal Grey Finish) 21-491P (Vacuum Metalized Chrome-VMC) 21-491R (Red Finish)

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-641 2006 MAZDA Mazdaspeed 6 L4-2.3L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)

INSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK

More information

INSTALLATION INSTRUCTIONS PART NUMBER:21-729

INSTALLATION INSTRUCTIONS PART NUMBER:21-729 Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-729 2010-2013 MAZDA MX-5 MIATA 2.0L I-4 PARTS LIST Description Qty. Part Number A Tube, Lower Intake, 2006-13

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-818C (GUN METAL GRAY FINISH) 2017 Nissan Sentra SR Turbo 1.6T 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157DK

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-703C (Gun Metal Grey Finish) 21-703P (Vacuum Metalized Chrome - VMC) 2011-2013 FORD Fiesta L4-1.6L C.A.R.B. E.O.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:41-1403 2010-2011 TOYOTA Corolla L4-1.8L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:22-516 2006-2007 HONDA Civic Si L4-2.0L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 41-1404 2008-2011 SCION XD L4-1.8L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8000 2002-2006 CADILLAC Escalade V8-6.0L C.A.R.B. E.O. # D-670-6 2002-2005 CADILLAC Escalade V8-5.3L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8402 1999-2004 TOYOTA Tacoma V6-3.4L C.A.R.B. E.O. # D-670 1999-2002 TOYOTA 4Runner V6-3.4L C.A.R.B. E.O. # D-670

More information

INSTRUCTIONS PART NUMBER:

INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-477 2006-2007 SUBARU Impreza WRX H4 2.5L Turbo C.A.R.B. E.O. # D-670-15 2004-2007 SUBARU Impreza WRX STi H4 2.5L

More information

7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions

7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions 7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9032 Year Make Model Engine Info CARB E.O. # 2012 Chevrolet Silverado 2500HD/3500 HD V8-6.6L DSL D-670-13 2012

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 41-1406 2006-2013 LEXUS IS250 V6-2.5L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information