COLD AIR INTAKE SYSTEM

Size: px
Start display at page:

Download "COLD AIR INTAKE SYSTEM"

Transcription

1 COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number Nissan Maxima SE/SL 3.5L V6 VQ35DE ADVANCED ENGINE MANAGEMENT INC TH Street, Unit A Hawthorne, CA Phone: (310) Fax: (310) Instruction Part Number: The applications listed are covered by at least one of the following EO numbers: Nissan Maxima V6 C.A.R.B. E.O. #D Nissan Maxima V6 C.A.R.B. E.O. #D Cold Air Systems that are pending CARB approval are illegal in California except on racing vehicles which may never be used on public highways Advanced Engine Management, Inc.

2 Congratulations! You have just purchased the finest Air Induction & Filtration system for your car at any price! The AEM Cold Air System is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot under hood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Cold Air Systems are 50 states Street Legal (some model and years still pending) and come with complete instructions for ease of installation. Our system is constructed of lightweight aluminum and then painted with a zirconia based powder coat for superior heat insulating characteristics. The aluminum will not crack in extended use like plastic and it is actually lighter than plastic. The tube diameter and length are matched for each engine to give power over a broad rpm range. Unlike the plastic systems that use a continually diverging cross section, we take advantage of the acoustical energy in the duct to promote cylinder filling during the intake valve-opening event. Bill of Materials for: Quantity Part Number Description D A/F ASSY 3.25 X 5" DRYFLOW INLET PIPE HOSE,SILICONE 3.25X3.0" HOSE,5/8ID #52 HOSE CLAMP #56 HOSE CLAMP HOSE CLAMP, 1 1/16" NARROW ZIP TIE,6 LONG ZIP TIE,8" TREE PUSH-MNT NUT,SERRATED 6MM WASHER,6MM SOFT MOUNT MOUNT,RUBBER 5/8" X 6MM RUBBER EDGE TRIM L-KEY, T20 TAMPER RESISTANT TORX INSTRUCTIONS DECAL,WARNING V S AEM DECAL 1

3 Read and understand these instructions BEFORE attempting to install this product. 1) Getting started a) Make sure vehicle is parked on a level surface. b) Set parking brake and remove key from ignition cylinder. c) Disconnect both battery terminals. d) If engine has run within the past two hours let it cool down. e) Jack up front of the vehicle and place on properly rated jack stands. f) Remove driver s side fender liner. 2) Removing the stock air inlet system a) Stock intake system. b) Free differential breather hose from inlet tube, if equipped. Use a supplied zip tie to secure the hose to the brake booster tube. c) Pull the crankcase breather hose from the valve cover. d) Loosen the two hose clamps on the ends of the inlet pipe. Remove the inlet pipe from the vehicle. 2

4 e) Free the clips that secure the mass air flow (MAF) sensor wiring harness. Unplug the MAF sensor. f) Remove the upper air box after first removing the bolt. g) Loosen the screws that secure the MAF sensor. Carefully remove the MAF sensor. h) From inside the fender well, remove the two bolts that secure the lower air box and remove the box from the vehicle. i) Unclip the two wiring harness connectors and move them two places lower. 3

5 3) Installation of the AEM Cold Air Intake System When installing the Cold Air Intake System, DO NOT completely tighten the hose clamps or mounting tab hardware until instructed to do so later in these instructions. a) Utilizing the stock screws, install the MAF sensor into the AEM CAS pipe. b) Slide the silicone coupler and supplied hose clamps over the throttle body. c) Install the rubber mount in the upper hole used to secure the lower air box. d) Install the rubber edge trim onto the metal lip behind the headlight. e) Place the inlet pipe in the engine bay. 4 f) Place the large washer over the mounting tab. Lightly thread the lock nut over the washer.

6 Rubber Mount Chassis Locknut Washer Inlet Pipe Support Tab g) Proper rubber mount installation. h) Place the air filter over the end of the inlet pipe. Tighten the air filter hose clamp. i) Attach the tree mount zip tie to the MAF sensor wiring harness. Trim the excess zip tie band. j) Plug the tree mount zip tie into the nipple near the MAF sensor. Plug in the MAF sensor. k) Secure one end of the supplied breather hose onto the valve cover with the supplied hose clamp. 5 l) Secure the other end of the breather hose to the inlet pipe with the supplied hose clamp. Zip tie the hose to the fuel line.

7 m) AEM Cold Air Intake System installed. 4) Reassemble the vehicle a) Reinstall the fender liner. b) Inspect the engine bay for any loose tools and check that all fasteners that were moved or removed are properly tightened. c) Confirm that the air filter does not contact any surface. d) Position the pipe so that it does not touch any surface, tighten all bolts, nuts or screws and tighten all hose clamps. e) Reconnect battery terminals. f) Start engine and perform a final inspection before driving the vehicle. 5) Service Information and Optional Accessories a) Service your AEM filter element with AEM's Filter Cleaning System (Part # ) at least every 50,000 miles or 30 months to maintain optimum performance. b) If you anticipate traveling through water that is deep enough to completely submerge the air filter, replace the AEM Cold Air System with the stock intake system. For Technical Inquiries Us At tech@aempower.com 6

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-433 2000-2004 Mitsubishi Eclipse RS & GS Congratulations! You have just purchased the finest Air Induction & Filtration system for your

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-483 2003-2008 Mazda 6 s V6 DO NOT install a bypass valve on this intake! Congratulations! You have just purchased the finest Air Induction

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-507 2002-2006 Acura RSX AT Inline 4, Automatic Transmission ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-475 2005-2006 Subaru Legacy 2.5L Turbo 2005-2006 Subaru Outback 2.5L Turbo Congratulations! You have just purchased the finest Air Induction

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number Mitsubishi Lancer Ralliart Manual Transmission Only

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number Mitsubishi Lancer Ralliart Manual Transmission Only COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-436 2004-2005 Mitsubishi Lancer Ralliart Manual Transmission Only ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne,

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-491 2005-2008 Mazda 6i 2.3L NON-PZEV Do not install a bypass valve on this intake system! ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH

More information

SHORT RAM AIR INTAKE SYSTEM. Installation Instructions for: Part Number Nissan 350Z

SHORT RAM AIR INTAKE SYSTEM. Installation Instructions for: Part Number Nissan 350Z SHORT RAM AIR INTAKE SYSTEM Installation Instructions for: Part Number 22-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Ford Focus SVT

COLD AIR SYSTEM. Installation Instructions for: Part Number Ford Focus SVT COLD AIR SYSTEM Installation Instructions for: Part Number 21-451 2002-2004 Ford Focus SVT ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Volkswagen Golf/GTI 1.8L Turbo Volkswagen Jetta 1.

COLD AIR SYSTEM. Installation Instructions for: Part Number Volkswagen Golf/GTI 1.8L Turbo Volkswagen Jetta 1. COLD AIR SYSTEM Installation Instructions for: Part Number 21-493 1999.5-2004 Volkswagen Golf/GTI 1.8L Turbo 1999.5-2004 Volkswagen Jetta 1.8L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street,

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-488 2004-2008 Mazda 3 s 2.3L 4cyl Congratulations! You have just purchased the finest Air Induction & Filtration system for your car

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Civic Si

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Civic Si COLD AIR SYSTEM Installation Instructions for: Part Number 21-508 2002-2004 Honda Civic Si ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Honda Civic Si

SHORT RAM SYSTEM. Installation Instructions for: Part Number Honda Civic Si SHORT RAM SYSTEM Installation Instructions for: Part Number 22-516 2006 Honda Civic Si ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S

COLD AIR SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S COLD AIR SYSTEM Installation Instructions for: Part Number 21-506 2002-2005 Acura RSX Type-S ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

ADVANCED ENGINE MANAGEMENT INC.

ADVANCED ENGINE MANAGEMENT INC. COLD AIR SYSTEM Installation Instructions for: Part Number 21-474 2002-2005 Subaru Impreza WRX 2004-2005 Subaru Impreza WRX STi 2004-2005 Subaru Forester XT 2004-2005 Saab 92X ADVANCED ENGINE MANAGEMENT

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda S2000

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda S2000 COLD AIR SYSTEM Installation Instructions for: Part Number 21-504 2000-2003 Honda S2000 Note: The installation of this Cold Air System requires the cutting or modification of plastic parts of the vehicle.

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Hyundai Tiburon V6

COLD AIR SYSTEM. Installation Instructions for: Part Number Hyundai Tiburon V6 COLD AIR SYSTEM Installation Instructions for: Part Number 21-521 2003-2005 Hyundai Tiburon V6 ATTENTION: This installation procedure requires some body modifications and may require the use of specialized

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S

SHORT RAM SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S SHORT RAM SYSTEM Installation Instructions for: Part Number 22-506 2002-2006 Acura RSX Type-S ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax:

More information

BRUTE FORCE INTAKE SYSTEM

BRUTE FORCE INTAKE SYSTEM BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8105 1988-1993 Ford Mustang 5.0L MAF Only ADVANCED ENGINE MANAGEMENT INC. 2205

More information

ADVANCED ENGINE MANAGEMENT INC.

ADVANCED ENGINE MANAGEMENT INC. COLD AIR SYSTEM Installation Instructions for: Part Number 21-493 1999.5-2005 Volkswagen GTI 1.8L 1999.5-2006 Volkswagen Golf 1.9L Turbo Diesel 1999.5 2005.5 Volkswagen Jetta 1.8L Turbo & 1.9L Turbo Diesel

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-486 2003-2003.5 MazdaSpeed Protégé 2.0L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR

COLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR COLD AIR SYSTEM Installation Instructions for: Part Number 21-469 2003-2004 Toyota Corolla 2002-2004 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

You can purchase this part at: COLD AIR SYSTEM

You can purchase this part at:   COLD AIR SYSTEM COLD AIR SYSTEM Installation Instructions for: Part Number 21-450 2000-2003 Ford Focus 2.0L Zetec ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax:

More information

Brute Force Intake System. Installation Instructions for: Part Number Toyota 4Runner 3.4L V Toyota Tacoma 3.

Brute Force Intake System. Installation Instructions for: Part Number Toyota 4Runner 3.4L V Toyota Tacoma 3. Brute Force Intake System Installation Instructions for: Part Number 21-8402 1999-2002 Toyota 4Runner 3.4L V6 1999-2004 Toyota Tacoma 3.4L V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A

More information

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Dodge SRT-4 2.4L

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Dodge SRT-4 2.4L SHORT RAM INTAKE SYSTEM Installation Instructions for: Part Number 22-425 2003-2005 Dodge SRT-4 2.4L ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required!

BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8103 96-04 Ford Mustang GT Excluding Bullet ADVANCED ENGINE MANAGEMENT INC. 2205

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Installation Instructions for: Part Number: 21-8209 2005-06 Dodge Dakota 4.7L V8 2006 Mitsubishi Raider Durocross/XLS 4.7L V8 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street,

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazda Miata

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazda Miata SHORT RAM SYSTEM Installation Instructions for: Part Number 22-482 2000-2003 Mazda Miata ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

ADVANCED ENGINE MANAGEMENT INC.

ADVANCED ENGINE MANAGEMENT INC. COLD AIR SYSTEM Installation Instructions for: Part Number 21-432 2001-2003 Chrysler Sebring Coupe Lxi 2001-2003 Dodge Stratus Coupe R/T 2000-2004 Mitsubishi Eclipse GT ADVANCED ENGINE MANAGEMENT INC.

More information

BRUTE FORCE INTAKE SYSTEM

BRUTE FORCE INTAKE SYSTEM BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8600 2006-2008 Honda Ridgeline 3.5L V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Infiniti G35

COLD AIR SYSTEM. Installation Instructions for: Part Number Infiniti G35 COLD AIR SYSTEM Installation Instructions for: Part Number 21-548 2003-2005 Infiniti G35 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Mazda RX-8 Instructions

COLD AIR SYSTEM. Installation Instructions for: Part Number Mazda RX-8 Instructions COLD AIR SYSTEM Installation Instructions for: Part Number 21-485 2004-2009 Mazda RX-8 Instructions ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Numbers & Honda Civic EX M/T Honda Civic DX/LX M/T

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Numbers & Honda Civic EX M/T Honda Civic DX/LX M/T COLD AIR INTAKE SYSTEM Installation Instructions for: Part Numbers 21-500 & 21-502 2001-2005 Honda Civic EX M/T 2001-2005 Honda Civic DX/LX M/T ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit

More information

BRUTE FORCE AIR INTAKE SYSTEM

BRUTE FORCE AIR INTAKE SYSTEM BRUTE FORCE AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-8108 1997-2000 Ford Ranger 4.0L V6 With O.E. panel style air filter ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit

More information

HYBRID INTAKE SYSTEM

HYBRID INTAKE SYSTEM HYBRID INTAKE SYSTEM Installation Instructions for: Part Number 21-5002 1988-1991 Honda Civic/CRX w/ B18C1 *Legal in California only for racing vehicles which may never be used upon a highway. ADVANCED

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Nissan 240SX

SHORT RAM SYSTEM. Installation Instructions for: Part Number Nissan 240SX SHORT RAM SYSTEM Installation Instructions for: Part Number 22-441 1995-1998 Nissan 240SX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required Installation Instructions for: Part Number 21-8013 2001-2004 Chevy Silverado 2500HD & 3500 2001-2004 GMC 2500HD & 3500 6.6L Duramax

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Nissan 350Z

COLD AIR SYSTEM. Installation Instructions for: Part Number Nissan 350Z COLD AIR SYSTEM Installation Instructions for: Part Number 21-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Matrix XRS

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Matrix XRS SHORT RAM SYSTEM Installation Instructions for: Part Number 22-466 2003 Toyota Matrix XRS ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Honda Accord 4-Cyl. 2.4L Excluding LX-P Model

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Honda Accord 4-Cyl. 2.4L Excluding LX-P Model SHORT RAM INTAKE SYSTEM Installation Instructions for: Part Number 22-511 2003-2004 Honda Accord 4-Cyl. 2.4L Excluding LX-P Model ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Corolla & 2003 Toyota Matrix XR

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Corolla & 2003 Toyota Matrix XR SHORT RAM SYSTEM Installation Instructions for: Part Number 22-469 2003-2004 Toyota Corolla & 2003 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

BRUTE FORCE AIR INTAKE SYSTEM

BRUTE FORCE AIR INTAKE SYSTEM BRUTE FORCE AIR INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8306 2005 Jeep Grand Cherokee 2006 Jeep Commander 5.7L V8 HEMI ADVANCED ENGINE

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazdaspeed Miata

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazdaspeed Miata SHORT RAM SYSTEM Installation Instructions for: Part Number 22-489 2004 Mazdaspeed Miata ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Ford Focus ZX3

SHORT RAM SYSTEM. Installation Instructions for: Part Number Ford Focus ZX3 SHORT RAM SYSTEM Installation Instructions for: Part Number 22-450 2000-2003 Ford Focus ZX3 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8005 1996-2004 Chevy Blazer 4.3L V6 1996-2004 Chevy S10 4.3L V6 1996-2003 Chevy

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Tacoma 4 Cyl Toyota 4Runner 4 Cyl.

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Tacoma 4 Cyl Toyota 4Runner 4 Cyl. SHORT RAM SYSTEM Installation Instructions for: Part Number 22-463 1995-1999 Toyota Tacoma 4 Cyl. 1996-1999 Toyota 4Runner 4 Cyl. ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.

More information

BRUTE FORCE AIR INTAKE SYSTEM

BRUTE FORCE AIR INTAKE SYSTEM BRUTE FORCE AIR INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8206 Dodge Ram 2500,3500 5.9L Turbo Diesel I6 2003-2005 ADVANCED ENGINE MANAGEMENT

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Civic CX/DX/LX

COLD AIR SYSTEM. Installation Instructions for: Part Number Civic CX/DX/LX COLD AIR SYSTEM Installation Instructions for: Part Number 21-413 1996-2000 Civic CX/DX/LX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8001 1992-1995 Chevy Trailblazer 5.7L V8 1988-1995 Chevy C/K Pickup 5.0L V8 1988-1995

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Prelude

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Prelude COLD AIR SYSTEM Installation Instructions for: Part Number 21-406 1997-2001 Honda Prelude ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-573 2006-2008 Toyota Yaris 1.5L *Legal in California only for racing vehicles which may never be used upon a highway. 2008, Advanced

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-8502 2004-2009 Nissan Titan 5.6L V8 2004-2009 Nissan Armada 5.6LV8 2004-2009 Infiniti QX56 5.6L V8 C.A.R.B. E.O. D-392-33 C.A.R.B.

More information

Kit Part Number:

Kit Part Number: 10-677 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-677 Nissan 350Z 3.5L V6 2007-2008 CARB EO # D-392-30 Short Ram Intake Systems that are pending an Executive Order number (EO#)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-682 2008 Chevrolet Cobalt SS CARB EO - D-392-32 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 41-1404 2008-2011 SCION XD L4-1.8L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679

V2 INTAKE SYSTEM. Patent No. 6,959,679 V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6016 1998-2002 Honda Accord V6 2001-2003 Acura CL V6 2000-2003 Acura TL V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-641 2006 MAZDA Mazdaspeed 6 L4-2.3L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Honda S2000

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Honda S2000 V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6104 2000-2005 Honda S2000 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2007-2008 Mazda Mazdaspeed 3 CARB EO # D-392-30 Cold Air Intake Systems that are pending an Executive Order number (EO#) relating to exemptions

More information

Equipped with AEM Dryflow Filter No Oil Required!

Equipped with AEM Dryflow Filter No Oil Required! Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-491B (Blue Finish) 21-491C (Gun Metal Grey Finish) 21-491P (Vacuum Metalized Chrome-VMC) 21-491R (Red Finish)

More information

LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED OR LICENSED FOR USE UPON A HIGHWAY.

LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED OR LICENSED FOR USE UPON A HIGHWAY. Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8408 2010-2013 TOYOTA Tundra V8-4.6L 2007-2014 TOYOTA Tundra V8-5.7L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES

More information

V2 INTAKE SYSTEM. Installation Instructions for: Part Number Acura RSX

V2 INTAKE SYSTEM. Installation Instructions for: Part Number Acura RSX V2 INTAKE SYSTEM Installation Instructions for: Part Number 24-6105 2002-2003 Acura RSX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-474 2007 SUBARU Impreza WRX STi H4-2.5L SEE * NOTE 2004-2006 SUBARU Impreza WRX STi H4-2.5L C.A.R.B. E.O. # D-670

More information

PART NUMBER:

PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8020 2006 PONTIAC GTO V8-6.0L SEE * NOTE 2005 PONTIAC GTO V8-6.0L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2008 Mitsubishi Lancer Evolution X CARB EO #: Pending AEM Cold Air Intake Systems that are pending an Executive Order number (EO#) relating

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8214 2006 Dodge Ram 3.7L V6 CARB EO # D-392-29. 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8304 1991-1995 JEEP Wrangler L4-2.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-568 2005-2006 Scion TC 2.4L *Legal in California only for racing vehicles which may never be used upon a highway. 2009, Advanced Engine

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-8315 1991-2001 Jeep Cherokee 4.0L I6 CARB EO # D392-30 Brute Force Intake Systems that are pending an Executive Order number (EO#)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8402 1999-2004 TOYOTA Tacoma V6-3.4L C.A.R.B. E.O. # D-670 1999-2002 TOYOTA 4Runner V6-3.4L C.A.R.B. E.O. # D-670

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-474 2006-2007 SUBARU Impreza WRX H4-2.5L C.A.R.B. E.O. # D-670-6 2004-2007 SUBARU Impreza WRX STi H4-2.5L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-507B (Blue Finish) 21-507C (Gun Metal Grey Finish) 21-507R (Red Finish) 2002-2006 ACURA RSX L4-2.0L Auto Trans.

More information

PART NUMBER: C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome - VMC)

PART NUMBER: C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome - VMC) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-686C (Gun Metal Grey Finish) 21-686P (Vacuum Metalized Chrome - VMC) 2006-2011 HONDA Civic L4-1.8L C.A.R.B. E.O.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 41-1406 2006-2013 LEXUS IS250 V6-2.5L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9210 1994-2002 DODGE Ram 2500 Pickup L6-5.9L DSL C.A.R.B. E.O. # D-670 1994-2002 DODGE Ram 3500 Pickup L6-5.9L

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:22-516 2006-2007 HONDA Civic Si L4-2.0L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-548 2003-2006 INFINITI G35 V6-3.5L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER: HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670

INSTALLATION INSTRUCTIONS PART NUMBER: HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670 Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6100 2001-2005 HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8306 2006 JEEP Commander V8-5.7L C.A.R.B. E.O. # D-670 2005-2006 JEEP Grand Cherokee V8-5.7L C.A.R.B. E.O. #

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9024 2006-2007 CHEVROLET Silverado 2500 HD Classic V8-6.6L DSL C.A.R.B. E.O. # D-670 2006-2007 CHEVROLET Silverado

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8315 1991-2001 JEEP Cherokee L6-4.0L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

AEM bypass valves are not compatible with this intake system (part number ) DO NOT attempt to install an AEM bypass valve on this intake system!

AEM bypass valves are not compatible with this intake system (part number ) DO NOT attempt to install an AEM bypass valve on this intake system! Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-452 2005 FORD Focus L4-2.0L SEE * NOTE 2004 FORD Focus L4-2.3L SEE * NOTE AEM bypass valves are not compatible

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-482 2000-2003 MAZDA Miata L4-1.8L C.A.R.B. E.O. # D-392-28 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER: C/P

INSTALLATION INSTRUCTIONS PART NUMBER: C/P Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-725C/P 2011-2016 SCION TC L4-2.5L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

Kit Part Number:

Kit Part Number: 10-8218 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8218 2007 Dodge Nitro 3.7L V6 CARB EO # D392-30 Brute Force Intake Systems that are pending an Executive Order number (EO#)

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9021 2004.5 CHEVROLET Silverado 3500 V8-6.6L DSL LB7 C.A.R.B. E.O. # D-670 2004.5 CHEVROLET Silverado 2500 HD

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra RS/LS

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra RS/LS V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6003 1994-2001 Acura Integra RS/LS ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-521 2003-2007 HYUNDAI Tiburon V6-2.7L C.A.R.B. E.O. # D-670-2 The installation of this AEM intake system requires

More information

Bill of Materials for

Bill of Materials for Bill of Materials for 77060012 1 2-P5153572 Inlet Pipe 1 21-202M 2.75" Filter 1 103-BLO-4820N Filter Hose Clamp 1 559999 Washer, Fender M6x25 1 1-3028 Washer, 1/4 SAE Flat 1 1-2072 Bolt, 1/4-20-UNC x 1

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-488 2006-2008 MAZDA 3 L4 2.3L SEE * NOTE 2004-2008 MAZDA 3 L4 2.0L SEE * NOTE 2004-2005 MAZDA 3 L4 2.3L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8207 2005 DODGE Durango V8-5.7L See * NOTE 2004 DODGE Durango V8-5.7L C.A.R.B. E.O. # D-670 * NOTE: Legal in

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9022 2005 CHEVROLET Silverado 2500 HD V8-6.6L DSL C.A.R.B. E.O. # D-670 2005 CHEVROLET Silverado 3500 V8-6.6L

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:41-1403 2010-2011 TOYOTA Corolla L4-1.8L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9211 2003-2006 DODGE Ram 2500 Pickup L6-5.9L DSL C.A.R.B. E.O. # D-670 2003-2006 DODGE Ram 3500 Pickup L6-5.9L

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

PART NUMBER:

PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8023 2007-08 CADILLAC Escalade V8-6.2L Exc. Mechanical Fan C.A.R.B. E.O. # D-670-2 2007-08 CHEVROLET Avalanche

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-778C (Gun Metal Gray Finish) 2015 MITSUBISHI LANCER 2.0 & 2.4L Excludes Test Group FMTXV02.0GEP C.A.R.B. E.O.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-685 2006-2011 HONDA Civic SI L4-2.0L SEE * NOTE * NOTE: Legal in California only for racing vehicles which may

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-490B (Blue Finish) 21-490C (Gun Metal Grey Finish) 21-490P (Vacuum Metalized Chrome-VMC) 21-490R (Red Finish)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8018 2006 HUMMER H3 L5-3.5L C.A.R.B. E.O. # D-670-2 2004-2006 CHEVROLET Colorado L5-3.5L C.A.R.B. E.O. # D-670-2

More information