COLD AIR INTAKE SYSTEM

Size: px
Start display at page:

Download "COLD AIR INTAKE SYSTEM"

Transcription

1 COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number Mitsubishi Eclipse RS & GS Congratulations! You have just purchased the finest Air Induction & Filtration system for your car at any price! ADVANCED ENGINE MANAGEMENT INC TH Street, Unit A Hawthorne, CA Phone: (310) Fax: (310) Instruction Part Number: Mitsubishi Eclipse RS & GS 4G64 C.A.R.B. E.O. #D Mitsubishi Eclipse RS & GS 4G64 C.A.R.B. E.O. #D Mitsubishi Eclipse RS & GS 4G64 C.A.R.B. E.O. #D Cold Air Intake Systems that are pending CARB approval are illegal in California except on racing vehicles which may never be used on public highways Advanced Engine Management, Inc.

2 The AEM Cold Air System is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot under hood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Cold Air Systems are 50 states Street Legal (some model and years still pending) and come with complete instructions for ease of installation. Our system is constructed of lightweight aluminum and then painted with a zirconia based powder coat for superior heat insulating characteristics. The aluminum will not crack in extended use like plastic and it is actually lighter than plastic. The tube diameter and length are matched for each engine to give power over a broad rpm range. Unlike the plastic systems that use a continually diverging cross section, we take advantage of the acoustical energy in the duct to promote cylinder filling during the intake valve-opening event. Bill of Materials for: Quanity Part Number Description D A/F Assy 2.75 X 5" Dryflow Short Inlet Pipe Long Inlet Pip e Inlet Pipe to MAF Sensor Adaptor 6.5" /8" Rubber Hose mm Nut mm x 25mm x 1mm Washer Soft Mount Hex Flange Bolt, M6 X 1 X Connector Hose x 3" " Rubber 90 degree Elbow Hose, a dapter 3.00/2.75X3" #52 Hose Clamp #44 Hose Clamp #48 Hose Clamp Socket Bolt, M6 x 1 x Instructions Hose Clamp, ¾ S AEM Decal 1

3 R ead and understand these instructions BEFORE attempting to install this product. 1) Getting started a) Make sure vehicle is parked on a level surface. b) Set parking brake. c) Disconnect both battery terminals. d) Jack up front of vehicle, place on properly rated jack stands, remove left, front wheel. Remove fender liner. e) If engine has run within the past two hours let it cool down. 2) Removing the stock air inlet system Upper clamp Breather hose a) Stock intake system. b) Pull breather hose off of valve cover. Loosen the upper and lower hose clamps on the stock inlet tube. c) Unplug the MAF sensor. Remove stock inlet pipe. Release four clamps on the air box and remove upper air box from the vehicle. d) Loosen the four nuts that hold the MAF sensor to the airbox. Carefully set aside the MAF sensor. 2

4 e) Release air snorkel by first pressing in the centers of the plastic rivets. f) Loosen the three bolts holding down the air box. Remove air box and snorkel from vehicle. g) Remove lower mounting bracket. h) Loosen the three bolts that hold in the lower air box and remove it from the vehicle. 3

5 3) Installation of the AEM Cold Air Intake System When installing the Cold Air Intake System, DO NOT completely tighten the hose clamps or mounting tab hardware until instructed to do so later in these instructions. Size 52 clamp a) Attach MAF adapter to MAF sensor using the supplied bolts and lock nuts. b) Attach rubber reducer to MAF sensor using the size 52 hose clamp. c) Place rubber elbow with two hose clamps onto the throttle body. The longer end attaches to the throttle body. d) Insert upper CAS pipe into rubber elbow. Confirm that the nipple on the pipe is pointing towards the center of the vehicle as shown. 4

6 e) Install the supplied breather hose as shown. Secure both ends with supplied ¾ hose clamps. f) Attach the bracket on the upper pipe to engine using the supplied 6mm bolt and washer. Place the pipe s tab behind the stock plastic tab. Also attach the MAF sensor to pipe utilizing the rubber adapter as shown. g) Plug wiring harness into MAF sensor and attach lower pipe to MAF sensor using silicone hose and two hose clamps. h) Install rubber mount into frame and attach support bracket as shown. Do not completely tighten the lock nut. See next page for proper installation. 5

7 Lock Nut Fender Washer Rubber Mount Chassis Inlet Pipe Support Tab i) Proper installation of the rubber mount. j) Install air filter to the lower end of the CAS pipe. Check clearance of the filter and tighten the hose clamp. 4) Reassemble the vehicle a) Inspect the engine bay for any loose tools and check that all fasteners that were moved or removed are properly tightened, including the fender liner. b) Position the pipes so that they do not touch any other surfaces and tighten all hose clamps, then tighten the bracket mount. c) Replace fender liner. d) Replace wheel and torque lug nuts to the proper value. e) Reconnect battery terminals. f) Start engine and perform a final inspection before driving the vehicle. For Technical Inquiries Us At tech@aempower.com 6

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-483 2003-2008 Mazda 6 s V6 DO NOT install a bypass valve on this intake! Congratulations! You have just purchased the finest Air Induction

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-549 2004-2006 Nissan Maxima SE/SL 3.5L V6 VQ35DE ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-507 2002-2006 Acura RSX AT Inline 4, Automatic Transmission ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-475 2005-2006 Subaru Legacy 2.5L Turbo 2005-2006 Subaru Outback 2.5L Turbo Congratulations! You have just purchased the finest Air Induction

More information

ADVANCED ENGINE MANAGEMENT INC.

ADVANCED ENGINE MANAGEMENT INC. COLD AIR SYSTEM Installation Instructions for: Part Number 21-432 2001-2003 Chrysler Sebring Coupe Lxi 2001-2003 Dodge Stratus Coupe R/T 2000-2004 Mitsubishi Eclipse GT ADVANCED ENGINE MANAGEMENT INC.

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number Mitsubishi Lancer Ralliart Manual Transmission Only

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number Mitsubishi Lancer Ralliart Manual Transmission Only COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-436 2004-2005 Mitsubishi Lancer Ralliart Manual Transmission Only ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne,

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Ford Focus SVT

COLD AIR SYSTEM. Installation Instructions for: Part Number Ford Focus SVT COLD AIR SYSTEM Installation Instructions for: Part Number 21-451 2002-2004 Ford Focus SVT ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Civic Si

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Civic Si COLD AIR SYSTEM Installation Instructions for: Part Number 21-508 2002-2004 Honda Civic Si ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

BRUTE FORCE INTAKE SYSTEM

BRUTE FORCE INTAKE SYSTEM BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8105 1988-1993 Ford Mustang 5.0L MAF Only ADVANCED ENGINE MANAGEMENT INC. 2205

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-488 2004-2008 Mazda 3 s 2.3L 4cyl Congratulations! You have just purchased the finest Air Induction & Filtration system for your car

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S

SHORT RAM SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S SHORT RAM SYSTEM Installation Instructions for: Part Number 22-506 2002-2006 Acura RSX Type-S ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax:

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Volkswagen Golf/GTI 1.8L Turbo Volkswagen Jetta 1.

COLD AIR SYSTEM. Installation Instructions for: Part Number Volkswagen Golf/GTI 1.8L Turbo Volkswagen Jetta 1. COLD AIR SYSTEM Installation Instructions for: Part Number 21-493 1999.5-2004 Volkswagen Golf/GTI 1.8L Turbo 1999.5-2004 Volkswagen Jetta 1.8L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street,

More information

SHORT RAM AIR INTAKE SYSTEM. Installation Instructions for: Part Number Nissan 350Z

SHORT RAM AIR INTAKE SYSTEM. Installation Instructions for: Part Number Nissan 350Z SHORT RAM AIR INTAKE SYSTEM Installation Instructions for: Part Number 22-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-491 2005-2008 Mazda 6i 2.3L NON-PZEV Do not install a bypass valve on this intake system! ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH

More information

Brute Force Intake System. Installation Instructions for: Part Number Toyota 4Runner 3.4L V Toyota Tacoma 3.

Brute Force Intake System. Installation Instructions for: Part Number Toyota 4Runner 3.4L V Toyota Tacoma 3. Brute Force Intake System Installation Instructions for: Part Number 21-8402 1999-2002 Toyota 4Runner 3.4L V6 1999-2004 Toyota Tacoma 3.4L V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR

COLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR COLD AIR SYSTEM Installation Instructions for: Part Number 21-469 2003-2004 Toyota Corolla 2002-2004 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Installation Instructions for: Part Number: 21-8209 2005-06 Dodge Dakota 4.7L V8 2006 Mitsubishi Raider Durocross/XLS 4.7L V8 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street,

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-486 2003-2003.5 MazdaSpeed Protégé 2.0L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Honda Civic Si

SHORT RAM SYSTEM. Installation Instructions for: Part Number Honda Civic Si SHORT RAM SYSTEM Installation Instructions for: Part Number 22-516 2006 Honda Civic Si ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda S2000

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda S2000 COLD AIR SYSTEM Installation Instructions for: Part Number 21-504 2000-2003 Honda S2000 Note: The installation of this Cold Air System requires the cutting or modification of plastic parts of the vehicle.

More information

BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required!

BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8103 96-04 Ford Mustang GT Excluding Bullet ADVANCED ENGINE MANAGEMENT INC. 2205

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Hyundai Tiburon V6

COLD AIR SYSTEM. Installation Instructions for: Part Number Hyundai Tiburon V6 COLD AIR SYSTEM Installation Instructions for: Part Number 21-521 2003-2005 Hyundai Tiburon V6 ATTENTION: This installation procedure requires some body modifications and may require the use of specialized

More information

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Numbers & Honda Civic EX M/T Honda Civic DX/LX M/T

COLD AIR INTAKE SYSTEM. Installation Instructions for: Part Numbers & Honda Civic EX M/T Honda Civic DX/LX M/T COLD AIR INTAKE SYSTEM Installation Instructions for: Part Numbers 21-500 & 21-502 2001-2005 Honda Civic EX M/T 2001-2005 Honda Civic DX/LX M/T ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit

More information

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Dodge SRT-4 2.4L

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Dodge SRT-4 2.4L SHORT RAM INTAKE SYSTEM Installation Instructions for: Part Number 22-425 2003-2005 Dodge SRT-4 2.4L ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

You can purchase this part at: COLD AIR SYSTEM

You can purchase this part at:   COLD AIR SYSTEM COLD AIR SYSTEM Installation Instructions for: Part Number 21-450 2000-2003 Ford Focus 2.0L Zetec ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax:

More information

BRUTE FORCE AIR INTAKE SYSTEM

BRUTE FORCE AIR INTAKE SYSTEM BRUTE FORCE AIR INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8206 Dodge Ram 2500,3500 5.9L Turbo Diesel I6 2003-2005 ADVANCED ENGINE MANAGEMENT

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Civic CX/DX/LX

COLD AIR SYSTEM. Installation Instructions for: Part Number Civic CX/DX/LX COLD AIR SYSTEM Installation Instructions for: Part Number 21-413 1996-2000 Civic CX/DX/LX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

HYBRID INTAKE SYSTEM

HYBRID INTAKE SYSTEM HYBRID INTAKE SYSTEM Installation Instructions for: Part Number 21-5002 1988-1991 Honda Civic/CRX w/ B18C1 *Legal in California only for racing vehicles which may never be used upon a highway. ADVANCED

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Nissan 240SX

SHORT RAM SYSTEM. Installation Instructions for: Part Number Nissan 240SX SHORT RAM SYSTEM Installation Instructions for: Part Number 22-441 1995-1998 Nissan 240SX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

ADVANCED ENGINE MANAGEMENT INC.

ADVANCED ENGINE MANAGEMENT INC. COLD AIR SYSTEM Installation Instructions for: Part Number 21-474 2002-2005 Subaru Impreza WRX 2004-2005 Subaru Impreza WRX STi 2004-2005 Subaru Forester XT 2004-2005 Saab 92X ADVANCED ENGINE MANAGEMENT

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Matrix XRS

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Matrix XRS SHORT RAM SYSTEM Installation Instructions for: Part Number 22-466 2003 Toyota Matrix XRS ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Infiniti G35

COLD AIR SYSTEM. Installation Instructions for: Part Number Infiniti G35 COLD AIR SYSTEM Installation Instructions for: Part Number 21-548 2003-2005 Infiniti G35 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

ADVANCED ENGINE MANAGEMENT INC.

ADVANCED ENGINE MANAGEMENT INC. COLD AIR SYSTEM Installation Instructions for: Part Number 21-493 1999.5-2005 Volkswagen GTI 1.8L 1999.5-2006 Volkswagen Golf 1.9L Turbo Diesel 1999.5 2005.5 Volkswagen Jetta 1.8L Turbo & 1.9L Turbo Diesel

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Corolla & 2003 Toyota Matrix XR

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Corolla & 2003 Toyota Matrix XR SHORT RAM SYSTEM Installation Instructions for: Part Number 22-469 2003-2004 Toyota Corolla & 2003 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazda Miata

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazda Miata SHORT RAM SYSTEM Installation Instructions for: Part Number 22-482 2000-2003 Mazda Miata ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Mazda RX-8 Instructions

COLD AIR SYSTEM. Installation Instructions for: Part Number Mazda RX-8 Instructions COLD AIR SYSTEM Installation Instructions for: Part Number 21-485 2004-2009 Mazda RX-8 Instructions ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Ford Focus ZX3

SHORT RAM SYSTEM. Installation Instructions for: Part Number Ford Focus ZX3 SHORT RAM SYSTEM Installation Instructions for: Part Number 22-450 2000-2003 Ford Focus ZX3 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S

COLD AIR SYSTEM. Installation Instructions for: Part Number Acura RSX Type-S COLD AIR SYSTEM Installation Instructions for: Part Number 21-506 2002-2005 Acura RSX Type-S ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8005 1996-2004 Chevy Blazer 4.3L V6 1996-2004 Chevy S10 4.3L V6 1996-2003 Chevy

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Prelude

COLD AIR SYSTEM. Installation Instructions for: Part Number Honda Prelude COLD AIR SYSTEM Installation Instructions for: Part Number 21-406 1997-2001 Honda Prelude ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Honda Accord 4-Cyl. 2.4L Excluding LX-P Model

SHORT RAM INTAKE SYSTEM. Installation Instructions for: Part Number Honda Accord 4-Cyl. 2.4L Excluding LX-P Model SHORT RAM INTAKE SYSTEM Installation Instructions for: Part Number 22-511 2003-2004 Honda Accord 4-Cyl. 2.4L Excluding LX-P Model ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required Installation Instructions for: Part Number 21-8013 2001-2004 Chevy Silverado 2500HD & 3500 2001-2004 GMC 2500HD & 3500 6.6L Duramax

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Tacoma 4 Cyl Toyota 4Runner 4 Cyl.

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Tacoma 4 Cyl Toyota 4Runner 4 Cyl. SHORT RAM SYSTEM Installation Instructions for: Part Number 22-463 1995-1999 Toyota Tacoma 4 Cyl. 1996-1999 Toyota 4Runner 4 Cyl. ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.

More information

BRUTE FORCE AIR INTAKE SYSTEM

BRUTE FORCE AIR INTAKE SYSTEM BRUTE FORCE AIR INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8306 2005 Jeep Grand Cherokee 2006 Jeep Commander 5.7L V8 HEMI ADVANCED ENGINE

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazdaspeed Miata

SHORT RAM SYSTEM. Installation Instructions for: Part Number Mazdaspeed Miata SHORT RAM SYSTEM Installation Instructions for: Part Number 22-489 2004 Mazdaspeed Miata ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Nissan 350Z

COLD AIR SYSTEM. Installation Instructions for: Part Number Nissan 350Z COLD AIR SYSTEM Installation Instructions for: Part Number 21-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

Brute Force Intake System

Brute Force Intake System Brute Force Intake System Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8001 1992-1995 Chevy Trailblazer 5.7L V8 1988-1995 Chevy C/K Pickup 5.0L V8 1988-1995

More information

BRUTE FORCE INTAKE SYSTEM

BRUTE FORCE INTAKE SYSTEM BRUTE FORCE INTAKE SYSTEM Equipped with AEM DRYFLOW Filter. No oil required! Installation Instructions for: Part Number 21-8600 2006-2008 Honda Ridgeline 3.5L V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126

More information

BRUTE FORCE AIR INTAKE SYSTEM

BRUTE FORCE AIR INTAKE SYSTEM BRUTE FORCE AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-8108 1997-2000 Ford Ranger 4.0L V6 With O.E. panel style air filter ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit

More information

INSTRUCTIONS PART NUMBER: B

INSTRUCTIONS PART NUMBER: B Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-432B (Blue Finish) 21-432C (Gun Metal Grey Finish) 21-432P (Vacuum Metalized Chrome-VMC) 21-432R (Red Finish)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-573 2006-2008 Toyota Yaris 1.5L *Legal in California only for racing vehicles which may never be used upon a highway. 2008, Advanced

More information

Kit Part Number:

Kit Part Number: 10-677 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-677 Nissan 350Z 3.5L V6 2007-2008 CARB EO # D-392-30 Short Ram Intake Systems that are pending an Executive Order number (EO#)

More information

AEM bypass valves are not compatible with this intake system (part number ) DO NOT attempt to install an AEM bypass valve on this intake system!

AEM bypass valves are not compatible with this intake system (part number ) DO NOT attempt to install an AEM bypass valve on this intake system! Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-452 2005 FORD Focus L4-2.0L SEE * NOTE 2004 FORD Focus L4-2.3L SEE * NOTE AEM bypass valves are not compatible

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8402 1999-2004 TOYOTA Tacoma V6-3.4L C.A.R.B. E.O. # D-670 1999-2002 TOYOTA 4Runner V6-3.4L C.A.R.B. E.O. # D-670

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679

V2 INTAKE SYSTEM. Patent No. 6,959,679 V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6016 1998-2002 Honda Accord V6 2001-2003 Acura CL V6 2000-2003 Acura TL V6 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Honda S2000

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Honda S2000 V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6104 2000-2005 Honda S2000 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-682 2008 Chevrolet Cobalt SS CARB EO - D-392-32 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra RS/LS

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra RS/LS V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6003 1994-2001 Acura Integra RS/LS ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

INSTALLATION INSTRUCTIONS PART NUMBER: HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670

INSTALLATION INSTRUCTIONS PART NUMBER: HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670 Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6100 2001-2005 HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

V2 INTAKE SYSTEM. Installation Instructions for: Part Number Acura RSX

V2 INTAKE SYSTEM. Installation Instructions for: Part Number Acura RSX V2 INTAKE SYSTEM Installation Instructions for: Part Number 24-6105 2002-2003 Acura RSX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-8502 2004-2009 Nissan Titan 5.6L V8 2004-2009 Nissan Armada 5.6LV8 2004-2009 Infiniti QX56 5.6L V8 C.A.R.B. E.O. D-392-33 C.A.R.B.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-432 2000-2005 MITSUBISHI Eclipse V6-3.0L C.A.R.B. E.O. # D-670-2 2005 MITSUBISHI Eclipse GT V6-3.0L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:41-1403 2010-2011 TOYOTA Corolla L4-1.8L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-507B (Blue Finish) 21-507C (Gun Metal Grey Finish) 21-507R (Red Finish) 2002-2006 ACURA RSX L4-2.0L Auto Trans.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 41-1404 2008-2011 SCION XD L4-1.8L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

PART NUMBER:

PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8020 2006 PONTIAC GTO V8-6.0L SEE * NOTE 2005 PONTIAC GTO V8-6.0L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California

More information

2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670. Will not fit MAF Sensor Equipped Vehicles

2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670. Will not fit MAF Sensor Equipped Vehicles Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-511 2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670 2003 HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670 Will not

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-548 2003-2006 INFINITI G35 V6-3.5L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-488 2006-2008 MAZDA 3 L4 2.3L SEE * NOTE 2004-2008 MAZDA 3 L4 2.0L SEE * NOTE 2004-2005 MAZDA 3 L4 2.3L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 41-1406 2006-2013 LEXUS IS250 V6-2.5L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2007-2008 Mazda Mazdaspeed 3 CARB EO # D-392-30 Cold Air Intake Systems that are pending an Executive Order number (EO#) relating to exemptions

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-568 2005-2006 Scion TC 2.4L *Legal in California only for racing vehicles which may never be used upon a highway. 2009, Advanced Engine

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-448 2005 CHEVROLET Cavalier Ecotec L4-2.2L SEE * NOTE 2005 PONTIAC Sunfire L4-2.2L C.A.R.B. E.O. # D-392-28 2003-2004

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED OR LICENSED FOR USE UPON A HIGHWAY.

LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED OR LICENSED FOR USE UPON A HIGHWAY. Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8408 2010-2013 TOYOTA Tundra V8-4.6L 2007-2014 TOYOTA Tundra V8-5.7L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-641 2006 MAZDA Mazdaspeed 6 L4-2.3L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles

More information

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra GS-R

V2 INTAKE SYSTEM. Patent No. 6,959,679. Installation Instructions for: Part Number Acura Integra GS-R V2 INTAKE SYSTEM Patent No. 6,959,679 Installation Instructions for: Part Number 24-6004 1994-2001 Acura Integra GS-R ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

Equipped with AEM Dryflow Filter No Oil Required!

Equipped with AEM Dryflow Filter No Oil Required! Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-491B (Blue Finish) 21-491C (Gun Metal Grey Finish) 21-491P (Vacuum Metalized Chrome-VMC) 21-491R (Red Finish)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-503 2001-2005 HONDA Civic L4-1.7L DX C.A.R.B. E.O. # D-392-29 2001-2005 HONDA Civic L4-1.7L LX C.A.R.B. E.O.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-544 2002-2006 NISSAN Sentra SE-R Spec-V L4-2.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9021 2004.5 CHEVROLET Silverado 3500 V8-6.6L DSL LB7 C.A.R.B. E.O. # D-670 2004.5 CHEVROLET Silverado 2500 HD

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8214 2006 Dodge Ram 3.7L V6 CARB EO # D-392-29. 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine

More information

PART NUMBER: MAZDA MX-5 L4-2.0L C.A.R.B. E.O. # D MAZDA MX-5 Miata L4-2.0L C.A.R.B. E.O. # D-670-6

PART NUMBER: MAZDA MX-5 L4-2.0L C.A.R.B. E.O. # D MAZDA MX-5 Miata L4-2.0L C.A.R.B. E.O. # D-670-6 Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-640 2006-2008 MAZDA MX-5 L4-2.0L C.A.R.B. E.O. # D-670-6 2006-2009 MAZDA MX-5 Miata L4-2.0L C.A.R.B. E.O. # D-670-6

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-463 1997-1999 TOYOTA Tacoma L4-2.7L C.A.R.B. E.O. # D-392-18 1997-1999 TOYOTA Tacoma L4-2.4L C.A.R.B. E.O. #

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8013 2004 CHEVROLET Silverado 2500 HD V8-6.6L DSL LB7 C.A.R.B. E.O. # D-392-27 2004 CHEVROLET Silverado 3500

More information

Equipped with AEM Dryflow Filter No Oil Required!

Equipped with AEM Dryflow Filter No Oil Required! Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6001 1992-1995 HONDA Civic SI L4-1.6L C.A.R.B. E.O. # D-670 1992-1995 HONDA Civic LX L4-1.5L Manual Trans. C.A.R.B.

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9022 2005 CHEVROLET Silverado 2500 HD V8-6.6L DSL C.A.R.B. E.O. # D-670 2005 CHEVROLET Silverado 3500 V8-6.6L

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2008 Mitsubishi Lancer Evolution X CARB EO #: Pending AEM Cold Air Intake Systems that are pending an Executive Order number (EO#) relating

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9024 2006-2007 CHEVROLET Silverado 2500 HD Classic V8-6.6L DSL C.A.R.B. E.O. # D-670 2006-2007 CHEVROLET Silverado

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-778C (Gun Metal Gray Finish) 2015 MITSUBISHI LANCER 2.0 & 2.4L Excludes Test Group FMTXV02.0GEP C.A.R.B. E.O.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8018 2006 HUMMER H3 L5-3.5L C.A.R.B. E.O. # D-670-2 2004-2006 CHEVROLET Colorado L5-3.5L C.A.R.B. E.O. # D-670-2

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-685 2006-2011 HONDA Civic SI L4-2.0L SEE * NOTE * NOTE: Legal in California only for racing vehicles which may

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-474 2007 SUBARU Impreza WRX STi H4-2.5L SEE * NOTE 2004-2006 SUBARU Impreza WRX STi H4-2.5L C.A.R.B. E.O. # D-670

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8304 1991-1995 JEEP Wrangler L4-2.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8223DC (Gun Metal Grey Finish) 21-8223DP (Vacuum Metalized Chrome - VMC) 2008-2010 DODGE Challenger V8-6.1L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8222 2012 DODGE RAM 1500 V8-5.7L SEE * NOTE 2009-2011 DODGE RAM 1500 V8-5.7L C.A.R.B. E.O. # D-670-6 * NOTE:

More information

Kit Part Number:

Kit Part Number: 10-8218 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8218 2007 Dodge Nitro 3.7L V6 CARB EO # D392-30 Brute Force Intake Systems that are pending an Executive Order number (EO#)

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-490B (Blue Finish) 21-490C (Gun Metal Grey Finish) 21-490P (Vacuum Metalized Chrome-VMC) 21-490R (Red Finish)

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8000 2002-2006 CADILLAC Escalade V8-6.0L C.A.R.B. E.O. # D-670-6 2002-2005 CADILLAC Escalade V8-5.3L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-521 2003-2007 HYUNDAI Tiburon V6-2.7L C.A.R.B. E.O. # D-670-2 The installation of this AEM intake system requires

More information