Kit Part Number:

Size: px
Start display at page:

Download "Kit Part Number:"

Transcription

1 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: Scion TC 2.4L *Legal in California only for racing vehicles which may never be used upon a highway. 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine Management, Inc. All rights reserved. Advanced Engine Management Inc th Street, Unit A Hawthorne, CA Phone:

2 9440 (4) Page 2 of Rev 2

3 Bill of Materials QTY PART DESCRIPTION PART # QTY PART DESCRIPTION PART # 1 Upper Intake Pipe M5 Split Lock Washer Lower Intake Pipe Bolt, 8-32X5/16 SS X3.00 Hump Hose 2.50 X2.00 Silicone Coupler Bolt,Hex M5 X.8, 12MM 2.50 X5.00 Dryflow Filter D 4 #40 Hose Clamp ½ Helical Wrap mm Rubber Mount M6 Star Washer mm Serrated Nut AEM Decal S 3 6mm Washer Instructions #44 Hose Clamp Page 3 of Rev 2

4 1. Preparing Vehicle a) Make sure vehicle is parked on a level surface. b) Set parking brake. c) If engine has run in the past two hours let it cool down d) Disconnect the negative battery terminal. e) Remove front drivers side wheel. 2. Removal of Stock System a) Remove the two nuts securing the plastic engine cover to the valve cover. Remove the plastic engine cover from the engine bay. Recommended Tools: 10mm Socket 5/16 Nut Driver Pliers Extension Ratchet 10mm Wrench Installation Time: 2 hours b) Pull the EVAP purge hose free from the two rubber clips on the intake hose. Remove the crankcase breather hose from the intake tube. Save the factory clamp for use later in the installation. c) Unplug the mass air flow (MAF) sensor connector. Remove d) Free the EVAP vacuum switching valve (VSV) from the intake tube by pulling straight up. Remove the screw that secures the mounting bracket to the wire harness clip and to the VSV itself. Save the screw for reuse if the stock intake system is ever reinstalled Page 4 of Rev 2

5 e) Remove the two screws securing the MAF sensor. Remove the sensor, use care to avoid damaging it. Save the screws for reuse if the stock intake system is ever reinstalled. f) Release the two upper air box clips. g) Squeeze the spring clamp on the intake tube at the throttle body. Pull the tube clear of the throttle body. Remove the intake tube/upper air box as one assembly. h) Remove the air filter element to expose the lower air box mounting bolts. Remove the three bolts and lift the lower air box. i) Free the wire harness loom clip by gently squeezing the sides in. Remove the lower air box from the engine bay. Squeeze Tab j) Remove the fuse box cover by squeezing the tab and lifting upwards Page 5 of Rev 2

6 k) Remove the two plastic rivets securing the lower air duct. Remove the lower air duct from the engine bay. Replace the fuse box cover. l) Remove the self-tapping screw and plastic rivet from the plastic fender liner. m) Remove the three selftapping screws from the underside of the fender liner. Pull the liner back and tuck it behind the brake rotor. n) Remove the ground strap bolt located beneath the driver s side headlight. Save the bolt for reuse if the stock intake system is ever reinstalled Page 6 of Rev 2

7 3. Installation of Cold Air Intake a) When installing the intake system, DO NOT completely tighten the hose clamps or mounting tab hardware until instructed to do so. b) Install two of the supplied rubber mounts in the threaded holes shown in the picture to the left. Install hump hose at throttle body EVAP line c) Install the rubber hump hose on to the throttle body. Loosely secure with two #40 hose clamps. Wrap the supplied helical plastic wrap around the EVAP line where it will pass over the upper intake pipe. d) Insert the 90 degree bend of the upper intake pipe (the long one) into the fender from the engine bay. e) Install the upper intake pipe into the coupler at the throttle body. Leave the hose clamps loose for adjustment. f) The pipe brackets will line up with the rubber mounts installed in step 3b. Loosely secure the first one to the rubber mount with a washer and nut g) Loosely secure the second bracket to the rubber mount with a washer and nut Page 7 of Rev 2

8 h) Connect the breather hose to the nipple located on the intake pipe near that throttle body. Nut i) Install the remaining rubber mount in to the hole left vacant in step 2n. On the exposed thread on the backside of the mount, install the star washer, ground strap terminal, and locknut (in that order). Ground Strap Star Washer j) Attach the supplied coupler to the end of the upper intake pipe located in the fender well. Use the supplied hose clamps to secure it loosely in place for adjustment later. k) Install the lower intake pipe into the coupler. The bracket will line up with the rubber mount. Loosely secure the bracket with a washer and locknut. l) Install the AEM air filter on to the end of the pipe. Secure with the supplied hose clamp. m) Secure the MAF sensor to the AEM intake pipe with the supplied 8-32 screws. Use care to avoid damaging the o-ring Page 8 of Rev 2

9 n) Plug in the MAF sensor wire harness. Mount the EVAP VSV to the bracket on the upper intake pipe using the supplied M5 screw and washer. Insert the screw through the wire harness clip, the intake pipe bracket, and then thread it into the VSV. Adjust the wires so that they are not in tension. o) Adjust inlet pipes and couplers for best fitment. Make sure the AEM intake system does not come into contact with the vehicle anywhere. Tighten all hose clamps and mounting bracket locknuts. p) Reinstall plastic engine cover. q) Reinstall lower splashguard and plastic fender liner using the original factory hardware. Re-install driver s side tire and torque to proper specification. Remove jack stands and lower vehicle. Note: Failure to install the plastic splashguard and fender liner will result in diminished performance and increase the potential for engine damage due to water ingestion in rainy conditions. 4. Re-assemble Vehicle a) Position the inlet pipes for best fitment. Be sure that the pipes or any other components do not contact any part of the vehicle. Tighten the rubber mount, all bolts and hose clamps. b) Check for proper hood clearance. Re-adjust pipes if necessary and retighten them. c) Inspect the engine bay for any loose tools and check that all fasteners that were moved or removed are properly tight. d) Re-connect the negative terminal on the battery. e) Start engine. Let car idle for 3 minutes. Perform a final inspection before driving the vehicle Page 9 of Rev 2

10 5. Service and Maintenance a) It is recommended that you service your AEM Dryflow filter every 20,000 miles for optimum performance. Use AEM Dryflow cleaning kit part # b) Use aluminum polish to clean your polished AEM intake pipe. c) Use window cleaner to clean your powder coated Intake pipe. (NOTE: DO NOT USE Aluminum polish on a powder coated Intake pipe) For technical inquiries us at tech@aempower.com or call us at Option #3 12 MONTH LIMITED WARRANTY AEM warrants that its intake systems will last for the life of your vehicle. AEM will not honor this warranty due to mechanical damage (i.e. improper installation or fitment), damage from misuse, accidents or flying debris. AEM will not warrant its powder coating if the finish has been cleaned with a hydrocarbon-based solvent. The powder coating should only be cleaned with a mild soap and water solution. Proof of purchase of both the vehicle and AEM intake system is required for redemption of a warranty claim Page 10 of Rev 2

11 AEM S DYNAMOMETER TESTING PROCEDURE AEM performs dynamometer testing on a Mustang Dyno, model MDSP Three power pulls are performed on our dynamometer; horsepower and torque are recorded each time. The raw data of the three pulls is then corrected to the Society of Automotive Engineers (SAE) standard correction factor. The corrected values are averaged and graphed to rpm. The SAE standard (SAE J1349 Reaffirmed June 1995) for an internal combustion engine atmospheric correction factor is used to create standard power output numbers at any altitude, ambient air temperature and humidity. As with any test there are many variables in the testing of the power outputs, so your test results may not match those of AEM Page 11 of Rev 2

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-573 2006-2008 Toyota Yaris 1.5L *Legal in California only for racing vehicles which may never be used upon a highway. 2008, Advanced

More information

Kit Part Number:

Kit Part Number: 10-677 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-677 Nissan 350Z 3.5L V6 2007-2008 CARB EO # D-392-30 Short Ram Intake Systems that are pending an Executive Order number (EO#)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-8502 2004-2009 Nissan Titan 5.6L V8 2004-2009 Nissan Armada 5.6LV8 2004-2009 Infiniti QX56 5.6L V8 C.A.R.B. E.O. D-392-33 C.A.R.B.

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8214 2006 Dodge Ram 3.7L V6 CARB EO # D-392-29. 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine

More information

2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670. Will not fit MAF Sensor Equipped Vehicles

2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670. Will not fit MAF Sensor Equipped Vehicles Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-511 2004 HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670 2003 HONDA Accord L4-2.4L C.A.R.B. E.O. # D-670 Will not

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-548 2003-2006 INFINITI G35 V6-3.5L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

SCION xb L4-2.4L

SCION xb L4-2.4L Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-577 2008-2012 SCION xb L4-2.4L AEM Induction Systems 1 (800) 992-3000 WWW: http://www.aemintakes.com PARTS LIST

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-491 2005-2008 Mazda 6i 2.3L NON-PZEV Do not install a bypass valve on this intake system! ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-682 2008 Chevrolet Cobalt SS CARB EO - D-392-32 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine

More information

Equipped with AEM Dryflow Filter No Oil Required!

Equipped with AEM Dryflow Filter No Oil Required! Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-491B (Blue Finish) 21-491C (Gun Metal Grey Finish) 21-491P (Vacuum Metalized Chrome-VMC) 21-491R (Red Finish)

More information

AEM bypass valves are not compatible with this intake system (part number ) DO NOT attempt to install an AEM bypass valve on this intake system!

AEM bypass valves are not compatible with this intake system (part number ) DO NOT attempt to install an AEM bypass valve on this intake system! Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-452 2005 FORD Focus L4-2.0L SEE * NOTE 2004 FORD Focus L4-2.3L SEE * NOTE AEM bypass valves are not compatible

More information

COLD AIR INTAKE SYSTEM

COLD AIR INTAKE SYSTEM COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-488 2004-2008 Mazda 3 s 2.3L 4cyl Congratulations! You have just purchased the finest Air Induction & Filtration system for your car

More information

ADVANCED ENGINE MANAGEMENT INC.

ADVANCED ENGINE MANAGEMENT INC. COLD AIR SYSTEM Installation Instructions for: Part Number 21-493 1999.5-2005 Volkswagen GTI 1.8L 1999.5-2006 Volkswagen Golf 1.9L Turbo Diesel 1999.5 2005.5 Volkswagen Jetta 1.8L Turbo & 1.9L Turbo Diesel

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-469B (Blue Finish) 21-469C (Gun Metal Grey Finish) 21-469P (Vacuum Metalized Chrome-VMC) 21-469R (Red Finish)

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2007-2008 Mazda Mazdaspeed 3 CARB EO # D-392-30 Cold Air Intake Systems that are pending an Executive Order number (EO#) relating to exemptions

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-494B (Blue Finish) 21-494C (Gun Metal Grey Finish) 21-494P (Vacuum Metalized Finish) 21-494R (Red Finish) 2004

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-547 2003-2006 NISSAN 350Z V6-3.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

Kit Part Number:

Kit Part Number: 10-8218 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8218 2007 Dodge Nitro 3.7L V6 CARB EO # D392-30 Brute Force Intake Systems that are pending an Executive Order number (EO#)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8402 1999-2004 TOYOTA Tacoma V6-3.4L C.A.R.B. E.O. # D-670 1999-2002 TOYOTA 4Runner V6-3.4L C.A.R.B. E.O. # D-670

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-641 2006 MAZDA Mazdaspeed 6 L4-2.3L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER: C/P

INSTALLATION INSTRUCTIONS PART NUMBER: C/P Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-725C/P 2011-2016 SCION TC L4-2.5L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8207 2005 DODGE Durango V8-5.7L See * NOTE 2004 DODGE Durango V8-5.7L C.A.R.B. E.O. # D-670 * NOTE: Legal in

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8205 2003-2004 DODGE RAM 1500 Pickup V8-4.7L C.A.R.B. E.O. # D-392-29 * NOTE: Legal in California only for racing

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 41-1404 2008-2011 SCION XD L4-1.8L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-490B (Blue Finish) 21-490C (Gun Metal Grey Finish) 21-490P (Vacuum Metalized Chrome-VMC) 21-490R (Red Finish)

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-521 2003-2007 HYUNDAI Tiburon V6-2.7L C.A.R.B. E.O. # D-670-2 The installation of this AEM intake system requires

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-703C (Gun Metal Grey Finish) 21-703P (Vacuum Metalized Chrome - VMC) 2011-2013 FORD Fiesta L4-1.6L C.A.R.B. E.O.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:41-1403 2010-2011 TOYOTA Corolla L4-1.8L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

INSTRUCTIONS PART NUMBER: B

INSTRUCTIONS PART NUMBER: B Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-432B (Blue Finish) 21-432C (Gun Metal Grey Finish) 21-432P (Vacuum Metalized Chrome-VMC) 21-432R (Red Finish)

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Mazda RX-8 Instructions

COLD AIR SYSTEM. Installation Instructions for: Part Number Mazda RX-8 Instructions COLD AIR SYSTEM Installation Instructions for: Part Number 21-485 2004-2009 Mazda RX-8 Instructions ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-630 1991-1992 SATURN SC L4-1.9L Manual Trans. C.A.R.B. E.O. # D-670-6 1993-1994 SATURN SW2 L4-1.9L Manual Trans.

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2008 Mitsubishi Lancer Evolution X CARB EO #: Pending AEM Cold Air Intake Systems that are pending an Executive Order number (EO#) relating

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-518B (Blue Finish) 21-518C (Gun Metal Grey Finish) 21-518P (Vacuum Metalized Chrome-VMC) 21-518R (Red Finish)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-685 2006-2011 HONDA Civic SI L4-2.0L SEE * NOTE * NOTE: Legal in California only for racing vehicles which may

More information

Equipped with AEM DRYFLOW Filter No oil Required! Kit Part Number:

Equipped with AEM DRYFLOW Filter No oil Required! Kit Part Number: Equipped with AEM DRYFLOW Filter No oil Required! Kit Part Number: 2003-2006 Dodge Ram 5.9L Cummins Diesel CARB EO D-392-33 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:22-516 2006-2007 HONDA Civic Si L4-2.0L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-8203 2003-2005 Dodge Ram 5.7L V8 CARB EO # D-392-28 2005 Dodge Powerwagon Hemi CARB EO # D-392-28 Brute Force Intake Systems that are

More information

LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED OR LICENSED FOR USE UPON A HIGHWAY.

LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED OR LICENSED FOR USE UPON A HIGHWAY. Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8408 2010-2013 TOYOTA Tundra V8-4.6L 2007-2014 TOYOTA Tundra V8-5.7L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 41-1406 2006-2013 LEXUS IS250 V6-2.5L LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES WHICH MAY NEVER BE USED, REGISTERED

More information

Equipped with AEM Dryflow Filter No Oil Required!

Equipped with AEM Dryflow Filter No Oil Required! Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6001 1992-1995 HONDA Civic SI L4-1.6L C.A.R.B. E.O. # D-670 1992-1995 HONDA Civic LX L4-1.5L Manual Trans. C.A.R.B.

More information

PART NUMBER: C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome - VMC)

PART NUMBER: C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome - VMC) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-686C (Gun Metal Grey Finish) 21-686P (Vacuum Metalized Chrome - VMC) 2006-2011 HONDA Civic L4-1.8L C.A.R.B. E.O.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-488 2006-2008 MAZDA 3 L4 2.3L SEE * NOTE 2004-2008 MAZDA 3 L4 2.0L SEE * NOTE 2004-2005 MAZDA 3 L4 2.3L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8306 2006 JEEP Commander V8-5.7L C.A.R.B. E.O. # D-670 2005-2006 JEEP Grand Cherokee V8-5.7L C.A.R.B. E.O. #

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-544 2002-2006 NISSAN Sentra SE-R Spec-V L4-2.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing

More information

INSTALLATION INSTRUCTIONS PART NUMBER: AUDI A4 L4-2.0L C.A.R.B. E.O. # D-670-2

INSTALLATION INSTRUCTIONS PART NUMBER: AUDI A4 L4-2.0L C.A.R.B. E.O. # D-670-2 Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-681 2005.5-2008 AUDI A4 L4-2.0L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-414B (Blue Finish) 21-414C (Gun Metal Grey Finish) 21-414P (Vacuum Metalized Chrome-VMC) 21-414R (Red Finish)

More information

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Tacoma 4 Cyl Toyota 4Runner 4 Cyl.

SHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Tacoma 4 Cyl Toyota 4Runner 4 Cyl. SHORT RAM SYSTEM Installation Instructions for: Part Number 22-463 1995-1999 Toyota Tacoma 4 Cyl. 1996-1999 Toyota 4Runner 4 Cyl. ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA.

More information

PART NUMBER:

PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8020 2006 PONTIAC GTO V8-6.0L SEE * NOTE 2005 PONTIAC GTO V8-6.0L C.A.R.B. E.O. # D-670-2 * NOTE: Legal in California

More information

INSTALLATION INSTRUCTIONS PART NUMBER C (Gun Metal Gray Finish)

INSTALLATION INSTRUCTIONS PART NUMBER C (Gun Metal Gray Finish) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-765C (Gun Metal Gray Finish) 2014-16 MAZDA 3 2.0L *Manual Transmission Only 1 ITEM NO. PART NUMBER DESCRIPTION

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-482 2000-2003 MAZDA Miata L4-1.8L C.A.R.B. E.O. # D-392-28 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-696 2009-2010 DODGE Challenger V6-3.5L SEE * NOTE * NOTE: Legal in California only for racing vehicles which

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6110 2003-2006 HONDA Accord V6-3.0L C.A.R.B. E.O. # D-670 Excludes 2006 MY LEV II SULEV 6HNXV03.0WMC model year

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1.

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1. Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-799C (GUN METAL GRAY FINISH) 2014-16 NISSAN SENTRA 1.8L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157D AIR

More information

INSTRUCTIONS PART NUMBER:

INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-477 2006-2007 SUBARU Impreza WRX H4 2.5L Turbo C.A.R.B. E.O. # D-670-15 2004-2007 SUBARU Impreza WRX STi H4 2.5L

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-474 2007 SUBARU Impreza WRX STi H4-2.5L SEE * NOTE 2004-2006 SUBARU Impreza WRX STi H4-2.5L C.A.R.B. E.O. # D-670

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-425 2004-2005 DODGE Neon SRT-4 L4 2.4L SEE * NOTE 2003 DODGE Neon SRT-4 L4 2.4L C.A.R.B. E.O. # D-392-21 * NOTE:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8028 2010 CHEVROLET Camaro V6-3.6L SEE * NOTE * NOTE: Legal in California only for racing vehicles which may

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8500 2001-2003 NISSAN Frontier V6-3.3L C.A.R.B. E.O. # D-670 2001-2003 NISSAN Xterra V6-3.3L C.A.R.B. E.O. #

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-463 1997-1999 TOYOTA Tacoma L4-2.7L C.A.R.B. E.O. # D-392-18 1997-1999 TOYOTA Tacoma L4-2.4L C.A.R.B. E.O. #

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-448 2005 CHEVROLET Cavalier Ecotec L4-2.2L SEE * NOTE 2005 PONTIAC Sunfire L4-2.2L C.A.R.B. E.O. # D-392-28 2003-2004

More information

INSTALLATION INSTRUCTION PART NUMBER:

INSTALLATION INSTRUCTION PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTION PART NUMBER: 24-6003 1994-2001 ACURA Integra L4-1.8L Manual Trans. C.A.R.B. E.O. # D-670 Non VTEC models ONLY AEM bypass valves

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8214 2006 DODGE Ram 1500 Pickup V6-3.7L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-818C (GUN METAL GRAY FINISH) 2017 Nissan Sentra SR Turbo 1.6T 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157DK

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-450B (Blue Finish) 21-450C (Gun Metal Grey Finish) 21-450P (Vacuum Metalized Chrome-VMC) 21-450R (Red Finish)

More information

Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number:

Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 1999-2001 Ford F-350 6.8L V10 CARB EO # D-392-30 2009, Advanced Engine Management, Inc. AEM is a registered trademark of Advanced Engine

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-8315 1991-2001 Jeep Cherokee 4.0L I6 CARB EO # D392-30 Brute Force Intake Systems that are pending an Executive Order number (EO#)

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-447 1998-2001 CHEVROLET Cavalier L4-2.2L Manual trans. requires 20-455 C.A.R.B. E.O. # D-670 2000-2002 PONTIAC

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-451B (Blue Finish) 21-451C (Gun Metal Grey Finish) 21-451P (Vacuum Metalized Chrome-VMC) 21-451R (Red Finish)

More information

21-413B (Blue Finish) C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome-VMC) R (Red Finish)

21-413B (Blue Finish) C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome-VMC) R (Red Finish) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-413B (Blue Finish) 21-413C (Gun Metal Grey Finish) 21-413P (Vacuum Metalized Chrome-VMC) 21-413R (Red Finish)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-783C (Gun Metal Gray Finish) 2016 HYUNDAI TUCSON 1.6L TURBO C.A.R.B. E.O# D-670-24 2017 HYUNDAI TUCSON 1.6L TURBO

More information

INSTALLATION INSTRUCTIONS PART NUMBER: HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670

INSTALLATION INSTRUCTIONS PART NUMBER: HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670 Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6100 2001-2005 HONDA Civic EX L4-1.7L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-462B (Blue Finish) 21-462C (Gun Metal Grey Finish) 21-462P (Vacuum Metalized Chrome-VMC) 21-462R (Red Finish)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-503 2001-2005 HONDA Civic L4-1.7L DX C.A.R.B. E.O. # D-392-29 2001-2005 HONDA Civic L4-1.7L LX C.A.R.B. E.O.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8304 1991-1995 JEEP Wrangler L4-2.5L C.A.R.B. E.O. # D-670 * NOTE: Legal in California only for racing vehicles

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-474 2006-2007 SUBARU Impreza WRX H4-2.5L C.A.R.B. E.O. # D-670-6 2004-2007 SUBARU Impreza WRX STi H4-2.5L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-5001 1988-1991 HONDA Civic / CRX w/b18c5 & B16A Engine Swap SEE * NOTE The installation of this AEM intake system

More information

PART NUMBER: B (Blue Finish) C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome-VMC) R (Red Finish)

PART NUMBER: B (Blue Finish) C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome-VMC) R (Red Finish) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-403B (Blue Finish) 21-403C (Gun Metal Grey Finish) 21-403P (Vacuum Metalized Chrome-VMC) 21-403R (Red Finish)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8029 2011-2010 CHEVROLET Camaro V8-6.2L SEE * NOTE * NOTE: Legal in California only for racing vehicles which

More information

PART NUMBER: C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome - VMC) HONDA CRZ L4-1.5 C.A.R.B E.O.

PART NUMBER: C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome - VMC) HONDA CRZ L4-1.5 C.A.R.B E.O. Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-700C (Gun Metal Grey Finish) 21-700P (Vacuum Metalized Chrome - VMC) 2011-2014 HONDA CRZ L4-1.5 C.A.R.B E.O.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8013 2004 CHEVROLET Silverado 2500 HD V8-6.6L DSL LB7 C.A.R.B. E.O. # D-392-27 2004 CHEVROLET Silverado 3500

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8203 2003-2005 DODGE RAM 1500 Pickup V8-5.7L C.A.R.B. E.O. # D-670 2003-2005 DODGE RAM 2500 Pickup V8-5.7L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-9024 2006-2007 CHEVROLET Silverado 2500 HD Classic V8-6.6L DSL C.A.R.B. E.O. # D-670 2006-2007 CHEVROLET Silverado

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:22-489 2004 MAZDA Miata Mazdaspeed L4-1.8L C.A.R.B. E.O. # D-670 PARTS LIST Description Qty. Part Number Element

More information

INSTALLATION INSTRUCTIONS PART NUMBER C (Gun Metal Grey Finish)

INSTALLATION INSTRUCTIONS PART NUMBER C (Gun Metal Grey Finish) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-742C (Gun Metal Grey Finish) 2014 Subaru Forester XT H4-2.0L Turbo C.A.R.B. E.O.# D-670-22 1 ITEM NO. PART NUMBER

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8018 2006 HUMMER H3 L5-3.5L C.A.R.B. E.O. # D-670-2 2004-2006 CHEVROLET Colorado L5-3.5L C.A.R.B. E.O. # D-670-2

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 21-8315 1991-1995 Jeep Cherokee 4.0L I6 1996-2001 Jeep Cherokee 4.0L I6 CARB EO # Pending CARB EO # Pending Brute Force Intake Systems

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-778C (Gun Metal Gray Finish) 2015 MITSUBISHI LANCER 2.0 & 2.4L Excludes Test Group FMTXV02.0GEP C.A.R.B. E.O.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-19 CHEVROLET CRUZE 1.4T 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8013 2001-2004 CHEVROLET Silverado 2500 HD V8-6.6L DSL C.A.R.B. E.O. # D-670-2 2001-2004 CHEVROLET Silverado

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-742C (Gun Metal Grey Finish) 2014-16 Subaru Forester XT H4-2.0L Turbo C.A.R.B E.O.# D-670-24 1 ITEM NO. PART NUMBER

More information

INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH)

INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-804C (GUN METAL GRAY FINISH) 2016 SCION ia 1.5L 2017 TOYOTA YARIS ia 1.5L 1 ITEM NO. PART NUMBER DESCRIPTION QTY.

More information

PART NUMBER: C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome - VMC)

PART NUMBER: C (Gun Metal Grey Finish) P (Vacuum Metalized Chrome - VMC) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-729C (Gun Metal Grey Finish) 21-729P (Vacuum Metalized Chrome - VMC) 2010 MAZDA MX-5 MIATA 2.0L L-4 C.A.R.B.

More information

COLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR

COLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR COLD AIR SYSTEM Installation Instructions for: Part Number 21-469 2003-2004 Toyota Corolla 2002-2004 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! The installation of this AEM intake system requires some modification to the vehicle s inner fender. A specialized power tool will be needed to modify

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 22-432 2000-2005 MITSUBISHI Eclipse V6-3.0L C.A.R.B. E.O. # D-670-2 2005 MITSUBISHI Eclipse GT V6-3.0L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS PART NUMBER:

INSTALLATION INSTRUCTIONS PART NUMBER: Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 24-6004 1994-2001 ACURA Integra GSR L4-1.8L C.A.R.B. E.O. # D-670 AEM bypass valves are not compatible with this

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8223DC (Gun Metal Grey Finish) 21-8223DP (Vacuum Metalized Chrome - VMC) 2008-2010 DODGE Challenger V8-6.1L C.A.R.B.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-735WR (Wrinkle Red) 21-735WB (Wrinkle Black) 2015-16 Subaru WRX STI H4-2.5L C.A.R.B E.O. # D-670-24 2017 Subaru

More information

Kit Part Number:

Kit Part Number: Equipped with AEM DRYFLOW Filter No Oil Required! Kit Part Number: 2004.5-2005 Chevy/GMC 6.6L Duramax Diesel LLY CARB EO # D-392-29 8th # in the VIN is 2 on 2004 models. 2009, Advanced Engine Management,

More information