INSTALLATION INSTRUCTIONS FOR ELECTRONIC SENSOR-ACTIVATED LAVATORY FAUCETS

Transcription

1 Code No Rev. 6 (05/6) (Models shown with ISM Integral Spout Mixer) EF-275 Series Solar Powered with attery ackup Sensor ctivated Lavatory Faucets INSTLLTION INSTRUCTIONS FOR ELECTRONIC SENSOR-CTIVTED LVTORY FUCETS EF-250 Series attery Powered, Sensor ctivated Lavatory Faucets EF-200 Series dapter Powered, Sensor ctivated Lavatory Faucets EF-225 Series dapter Powered, Sensor ctivated Lavatory Faucets with Temperature Indicating Illumination LIMITED WRRNTY FUCET VRITIONS -ISM Integral Spout Mixer (ll Series) -IC -Click Feature (ll Series) -DPU Drain Pop Up (EF-200/225/250 Series) -P Plug-in Transformer/dapter (EF-200 Series) -LT Less Transformer/dapter (EF-200 Series) Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and workmanship for a period of three (3) years (one () year for special finishes, SF faucets, PWT electronics and 30 days for PWT software) from date of first purchase. During this period, Sloan Valve Company will, at its option, repair, replace, or refund the purchase price of any product which fails to conform with this warranty under normal use and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer s cost. No claims will be allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries. THERE RE NO WRRNTIES WHICH EXTEND EYOND THE DESCRIPTION ON THE FCE HEREOF. IN NO EVENT IS SLON VLVE COMPNY RESPONSILE FOR NY CONSEQUENTIL DMGES OF NY MESURE WHTSOEVER. PRIOR TO INSTLLTION Prior to installing the Sloan Optima EF-275/EF-250/EF-200/EF-225 Series Faucets, install the items listed below. lso, refer to rough-in illustrations. Lavatory/sink Drain line Hot and cold water supply lines or pre-tempered water supply line Important: LL PLUMING SHOULD E INSTLLED IN CCORDNCE WITH PPLICLE CODES ND REGULTIONS. TOOLS REQUIRED FOR INSTLLTION 3 mm open end wrench or nut driver for faucet retainer nut FLUSH LL WTER LINES PRIOR TO MKING CONNECTIONS. KEEP THRED SELNT OUT OF YOUR WTERWY TO PREVENT COMPONENT PRT DMGE! DO NOT USE NY SELNT ON COMPRESSION FITTINGS. Trim Plates When the EF Faucet is installed on a sink that has three (3) hole punchings, a Trim Plate should be used. Trim Plates must be specified and ordered separately. ETF-32- Trim Plate for 4 (02 mm) Centerset Sink ETF-50- Trim Plate for 8 (203 mm) Centerset Sink 3/4 open end wrench for female end of flex hose FUCET ROUGH-IN MODELS EF-200/250/ gpm (.9 Lpm) Max. Flow Faucets with Single Line Water Supply SPOUT MODELS EF-200/225*/250/ gpm (.9 Lpm) Max. Flow Faucets with Hot and Cold Water Supply MIXING LEVER SPOUT (Can e Set and Removed) 4-/32 (0 mm) 24º O-RING -3/6 (30 mm) MIN. DI. HOLE REQUIRED O-RING -3/6 (30 mm) MIN. DI. HOLE REQUIRED GSKET RETINER NUT -/2 (38 mm) MX. DECK THICKNESS GSKET RETINER NUT -/2 (38 mm) MX. DECK THICKNESS 2-/6 (52 mm) TEMPERED SUPPLY 3 (330 mm) LONG FLEX HOSE If a connection to separate hot and cold water supplies is desired, then a ak-chek tee fitting (not supplied) must be used prior to connecting to the faucet. HOT SUPPLY 3 (330 mm) LONG FLEX HOSE COLD SUPPLY 5-/32 (36 mm) 2-/6 (52 mm) 2-9/6 (65 mm) *EF-225 Series Faucets are furnished with a.5 gpm (5.6 Lpm) spray head

2 - INSTLL FUCET Remove Nut, Faucet Retainer and Gasket. DO NOT remove the O-ring from base of Faucet. DO NOT remove Sensor label unitl Step 4. O-RING DO NOT REMOVE GSKET FUCET RETINER NUT 2 - SLIDE GSKET OVER FLEX HOSE(S) ND SECURE Install Faucet with O-ring into the center hole in deck or lavatory -3/6 (30 mm) min. hole required. Note: If installing the Faucet on a three (3) hole sink, a Trim Plate should be installed at this time. FUCET O-RING CENTER HOLE IN DECK OR LVTORY FUCET O-RING GSKET FUCET RETINER FLEX HOSE 3 mm NUT MODELS POWERED Y PLUG-IN DPTER ONLY DO NOT pull or crimp C Power Line. 3 - INSTLL STRINER ND FLEX HOSE ONTO SUPPLY STOP. OPEN SUPPLY STOPS IMPORTNT: Flush dirt, debris, and sediment from supply line(s) before Connecting Flex Hoses. FLEX HOSE Install Strainer and Flex Hose onto Supply Stop. Tighten the Flex Hose (with Strainer in place) securely to the Supply. STRINER SUPPLY LINE/ STOP 4 - EF-200 MODELS: PLUG DPTER INTO RECEPTCLE. LL MODELS - REMOVE LEL FROM SENSOR. For EF-200 Models, Plug dapter into receptacle. Remove Label from Sensor Window. C Open Supply Stop(s). Electrical Connection for up to Six (6) Faucets Using One () dapter 6 VDC PLUG- IN DPTER SENSOR LEL NOTE: EF-225 can only connect one () faucet per one () adapter. DPTER 2 DISY CHIN ELECTRICL CLE DISY CHIN ELECTRICL CLE DISY CHIN ELECTRICL CLE TO DDITIONL FUCETS (6 MX.)

3 5 - CTIVTE FUCET ctivate Faucet by pressing the button one () time, then immediately step away. Faucet will run for four (4) seconds and the range will automatically adjust to its environment. Wait ten (0) seconds after water shuts off before using Faucet. ctivate Faucet and check for leaks. If Faucet does not function, refer to the Troubleshooting section of this instruction manual. 6 - SET ND FIX TEMPERTURE (MODEL EF-225, SEE PGE 4) djust lever to set temperature. Optional To fix temperature, set lever to the desired position, then remove lever and plug hole with Cap. 7 - TTERY REPLCEMENT (EF-250/275) NOTE: Replace attery when red LED indicator flashes each time faucet is in use or when faucet stops functioning. Close Supply Stop(s). Loosen Screw with hex wrench and remove Cap. C Move attery Retainer tab away from attery. Remove old attery. Dispose of properly. D E Insert a new 6 Volt Type CR-P2 Lithium attery. The red LED will flash for one () minute. Reinstall attery Cover. If LED doesn t flash or if it just lights up, remove and then reinsert the attery. If water flows continuously after inserting the new attery and opening the Supply Stops, remove and then reinsert the attery. Open Supply Stop(s). SETTINGS -CLICK SETTINGS Function Press utton LED Signal Continuous Run 2 minute default setting (adjustable from - 20 minutes) reset: time for 2 seconds 5 short flashes time or will reset automatically after 2 minutes Temporary Off 2 times (double click) 5 short flashes followed by periodic flashing time or will reset reset: automatically after 2 minutes uto Set Range djustment 2 times (double click) and then time for 5 seconds 5 short flashes followed by 4 short flashes 3

4 MODEL EF-225 ONLY Functions RED HOT End Position LUE Cold End Position Tempered Position Setting rightness of Illumination Remove cover. Press button for approximately 5 C When illuminant glows PURPLE, E Press button once. F Replace top cover. seconds. release. D djust the illumination by turning the mixing lever to desired brightness. 4

5 MODEL EF-225 ONLY Calibrating the illuminant colors (RED - WHITE - LUE) to water temperature Remove cover. Press button twice and release. C Illuminant flashes red. E Illuminant flashes F djust mixing lever for position D djust mixing lever for position RED (hot) and press button once. G Illuminant flashes LUE.. once. H djust mixing lever for position LUE (cold) and press button once. 5 I (temperate) and press button Replace cover.

6 SENSOR RNGE DJUSTMENT FCTORY SETTING IS PPROPRITE FOR THE MJORITY OF PPLICTIONS ND SHOULD NOT REQUIRE RESETTING UNLESS UNDER EXTREME SITUTIONS. 4x 2x + x 5 sec C x ( x, 2x,...,8x) D 8x 7x 6x = factory setting 5x 4x 3x 2x x DISCLIMER: Updated electronics have visible red and green LED. Original electronics have only red LED and range setting is reversed (=longest, 8=shortest) E F G 6

7 ... 2 x 2/24 LINE PURGE FETURE This feature will operate the faucet every 2 or 24 hours since last use, if not used to prevent stagnant water conditions. Default purge duration is two minutes. Consult factory regarding other timing options. x 24 sec +... C... 2 x ctivate 2HR... 3 x... 3 x ctivate 24HR D... x Deactivate HOT LIMIT STOP DJUSTMENT... x C OPERTION s the user s hands enter the beam s effective range, the beam is reflected back into the sensor receiver and activates the solenoid valve allowing water to flow from the faucet. Water will flow until the hands are removed or until the faucet reaches its automatic time out limit setting. CRE ND CLENING DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to clean Faucets that may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom tile, protect the Faucet from any splattering of cleaner. cids and cleaning fluids will discolor or remove chrome plating. 7

8 TROULESHOOTING GUIDE. Problem: Faucet does not function. Cause: dhesive packaging label affixed over sensor eye. Solution: Remove adhesive label from sensor eye. Cause: Permanent Off activated. Solution: Press button on faucet throat one time. 2. Problem: Faucet delivers water in an uncontrolled manner. Cause: Faucet is defective. Solution: Contact the Sloan Technical Support (see below). 3. Problem: Faucet does not deliver any water when Sensor is activated. Indicator: Solenoid valve produces an audible CLICK. Cause: Water supply stop(s) closed. Solution: Open water supply stop(s). Cause: Water supply stop strainer(s) clogged. Solution: Remove, clean, and reinstall water supply stop strainer(s). Replace strainer(s) if required. Indicator: Solenoid valve DOES NOT produce an audible CLICK. Cause: attery low (battery-powered models). Solution: Replace battery (refer to attery Replacement on Page 3). Cause: Power failure (EF-200 Models). Solution: Check power supply. 4. Problem: Faucet delivers only a slow flow or dribble when Sensor is activated. Cause: Water supply stop(s) are partially closed. Solution: Completely open water supply stop(s). Cause: Water supply stop strainer(s) clogged. Solution: Remove, clean, and reinstall water supply stop strainer(s). Replace strainer(s) if required. 4. Problem: Faucet delivers only a slow flow or dribble when Sensor is activated. Cause: erator is clogged. Solution: Remove, clean, and reinstall aerator. Replace aerator if required. Cause: Faucet is defective. Solution: Contact the Sloan Technical Support (see below). 5. Problem: Faucet does not stop delivering water or continues to drip after user is no longer detected. Cause: Valve is defective. Solution: Contact the Sloan Technical Support (see below). 6. Problem: LED indicator blinks when faucet is in use. Cause: attery low (battery-powered models). Solution: Replace battery (refer to attery Replacement on Page 3). 7. Problem: The water temperature is too hot or too cold on a faucet connected to hot and cold supply lines. Cause: Supply Stops are not adjusted properly. Solution: djust Supply Stops. Cause: For models with integral mixing valve Mixing valve is set improperly for the water temperature desired. Solution: Rotate mixing valve handle clockwise to decrease water temperature or counterclockwise to increase water temperature. When assistance is required, please contact Sloan Technical Support at: -888-SLON-4 ( ) PRTS LIST C 3D C 7 Item # Part # Description EF-4- Faucet Sensor ssembly (EF-275 only) EF-9- Faucet Sensor ssembly (EF-200 and EF-225 only) EF-2- Faucet Sensor ssembly (EF-250 only) EF-6- Faucet Sensor ssembly with i.q.-click (EF-275 only) EF-8- Faucet Sensor ssembly with i.q.-click (EF-200 and EF-225 only) EF-20- Faucet Sensor ssembly with i.q.-click (EF-250 only) 2 EF-006 Cap with Solar Cell ssembly (EF-275 only) 2 EF-27 Cap (EF-250 and EF-200 only) 2C Cap (EF-225) 3 EF gpm (.9 Lpm) VR Pressure Compensating Spray Head 3 EF-22.5 gpm (5.6 Lpm) Pressure Compensating erated Stream 3C EF gpm (8.3 Lpm) erator Spray Head 3D EF gpm (8.3 Lpm) Laminar Flow Spray Head 4 EF-003 attery Replacement Kit 5 EF- Faucet Mounting Kit 6 EF-9 Strainer (Filter) 7 EF-004 Mixer Handle ssembly and Cartridge 7 EF-005 Handle Repair Kit 8 EF-007 Handle Cap 9 EF (330 mm) Flexible Supply Hose 0 EF-44 Power Splitter EF /6 (300 mm) Extension Cable EF /4 (200 mm) Extension Cable EF-7-26 (3200 mm) Extension Cable 2 ETF-32- Trim Plate for 4 Centerset Sink 3 ETF-50- Trim Plate for 8 Centerset Sink 4 EF- Plug-in dapter (Models EF-200/225) 5 EF-2 Solenoid EF-44 replaces the separate EF-23- Splitter Cable and EF-28 Capacitor, which is sold separately. The information contained in this document is subject to change without notice. SLON 0500 SEYMOUR VENUE FRNKLIN PRK, IL 603 Phone: or Fax: or SLON Code No: Rev. 6 (05/6)