INSTALLATION INSTRUCTIONS FOR ELECTRONIC SENSOR ACTIVATED LAVATORY FAUCETS

Transcription

1 Code No Rev. 4 (12/10) (Models shown with ISM Integral Spout Mixer) EF-275 Series Solar Powered with attery ackup Sensor ctivated Lavatory Faucets INSTLLTION INSTRUCTIONS FOR ELECTRONIC SENSOR CTIVTED LVTORY FUCETS EF-250 Series attery Powered, Sensor ctivated Lavatory Faucets EF-200 Series dapter Powered, Sensor ctivated Lavatory Faucets EF-225 Series dapter Powered, Sensor ctivated Lavatory Faucets with Temperature Indicating Illumination FUCET VRITIONS -ISM Integral Spout Mixer (ll Series) -IC -Click Feature (ll Series) -DPU Drain Pop Up (EF-200/225/250 Series) -P Plug-in Transformer/dapter (EF-200 Series) -LT Less Transformer/dapter (EF-200 Series) LIMITED WRRNTY Sloan Valve Company warrants its Optima EF-275, EF-250, EF-225 and EF-200 Series Electronic Hand Washing Faucets to be made of first class materials, free from defects of material or workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the battery. THERE RE NO WRRNTIES WHICH EXTEND EYOND THE DESCRIPTION ON THE FCE HEREOF. IN NO EVENT IS SLON VLVE COMPNY RESPONSILE FOR NY CONSEQUENTIL DMGES OF NY MESURE WHTSOEVER. PRIOR TO INSTLLTION Prior to installing the Sloan Optima EF-275/EF-250/EF-200/EF-225 Series Faucets, install the items listed below. lso, refer to rough-in illustrations. Lavatory/sink Drain line Hot and cold water supply lines or pre-tempered water supply line Important: LL PLUMING SHOULD E INSTLLED IN CCORDNCE WITH PPLICLE CODES ND REGULTIONS. TOOLS REQUIRED FOR INSTLLTION 13 mm open end wrench or nut driver for faucet retainer nut FLUSH LL WTER LINES PRIOR TO MKING CONNECTIONS. KEEP THRED SELNT OUT OF YOUR WTERWY TO PREVENT COMPONENT PRT DMGE! DO NOT USE NY SELNT ON COMPRESSION FITTINGS. Trim Plates When the EF Faucet is installed on a sink that has three (3) hole punchings, a Trim Plate should be used. Trim Plates must be specified and ordered separately. ETF-312- Trim Plate for 4 (102 mm) Centerset Sink ETF-510- Trim Plate for 8 (203 mm) Centerset Sink 3/4 open end wrench for female end of flex hose FUCET ROUGH-IN SPOUT MODELS EF-200/250/ gpm (8.3 Lpm) Max. Flow Faucets with Single Line Water Supply MODELS EF-200/225/250/275 WITH VRITIONS 2.2 gpm (8.3 Lpm) Max. Flow Faucets with Hot and Cold Water Supply MIXING LEVER SPOUT (Can e Set and Removed) 4-11/32 (110 mm) 24º O-RING 1-3/16 (30 mm) MIN. DI. HOLE REQUIRED O-RING 1-3/16 (30 mm) MIN. DI. HOLE REQUIRED GSKET RETINER NUT TEMPERED SUPPLY 1-1/2 (38 mm) MX. DECK THICKNESS GSKET RETINER 13 (330 mm) LONG FLEX HOSE 5-11/32 (136 mm) If a connection to separate hot and cold water supplies is desired, then a ak-chek tee fitting (not supplied) must be used prior to connecting to the faucet. HOT SUPPLY NUT 13 (330 mm) LONG FLEX HOSE 1-1/2 (38 mm) MX. DECK THICKNESS COLD SUPPLY 2-1/16 (52 mm) 2-1/16 (52 mm) 2-9/16 (65 mm) EF-275 Series Faucets are furnished with a 0.5 gpm (1.9 Lpm) Spray Head.

2 1 - INSTLL FUCET. Remove Nut, Faucet Retainer and Gasket. DO NOT remove the O-ring from base of Faucet. O-RING DO NOT REMOVE Install Faucet with O-ring into the center hole in deck or lavatory 1-3/16" (30 mm) min. hole required. Note: If installing the Faucet on a three (3) hole sink, a Trim Plate should be installed at this time. FUCET O-RING GSKET FUCET RETINER NUT 2 - SLIDE GSKET OVER FLEX HOSE(S) ND SECURE. CENTER HOLE IN DECK OR LVTORY FUCET O-RING GSKET FUCET RETINER FLEX HOSE 13 mm NUT MODELS POWERED Y PLUG-IN DPTER ONLY DO NOT pull or crimp C Power Line. 3 - INSTLL STRINER ND FLEX HOSE ONTO SUPPLY STOP. OPEN SUPPLY STOPS. IMPORTNT: Flush dirt, debris, and sediment from Supply Line(s) before Connecting Flex Hoses. Install Strainer and Flex Hose onto Supply Stop. FLEX HOSE Tighten the Flex Hose (with Strainer in place) securely to the Supply. For EF-200 Models, Plug dapter into receptacle. STRINER SUPPLY LINE/ STOP Remove Label from Sensor Window. C Open Supply Stop(s). 4 - EF-200 MODELS: PLUG DPTER INTO RECEPTCLE. LL MODELS - REMOVE LEL FROM SENSOR. Electrical Connection for up to Six (6) Faucets Using One (1) dapter 6 VDC PLUG-IN DPTER SENSOR LEL NOTE: EF-225 can only connect one (1) faucet per one (1) adapter. DPTER 2 DISY CHIN ELECTRICL CLE DISY CHIN ELECTRICL CLE DISY CHIN ELECTRICL CLE TO DDITIONL FUCETS (6 MX.)

3 5 - CTIVTE FUCET. ctivate Faucet by pressing the button one (1) time, then immediately step away. Faucet will run for four (4) seconds and the range will automatically adjust to its environment. Wait ten (10) seconds after water shuts off before using Faucet. ctivate Faucet and check for leaks. If Faucet does not function, refer to the Troubleshooting section of this instruction manual. 6 - SET ND FIX TEMPERTURE (MODEL EF-225, SEE PGE 5) djust lever to set temperature. Optional To fix temperature, set lever to the desired position, then remove lever and plug hole with Cap. 7 - TTERY REPLCEMENT (EF-250/275) NOTE: Replace attery when red LED indicator flashes each time faucet is in use or when faucet stops functioning. Close Supply Stop(s). D Insert a new 6 Volt Type CR-P2 Lithium attery. The red LED will flash for one (1) minute. Reinstall attery Cover. If LED doesn't flash or if it just lights up, remove and then reinsert the attery. If water flows continuously after inserting the new attery and opening the Supply Stops, remove and then reinsert the attery. Loosen Screw with hex wrench and remove Cap. C Move attery Retainer tab away from attery. Remove old attery. Dispose of properly. E Open Supply Stop(s). SETTINGS -Click SETTINGS Function Press utton LED Signal Continuous Run 2 minute default setting (adjustable from 1-20 minutes) reset: 1 time for 2 seconds 5 short flashes 1 time or will reset automatically after 2 minutes Temporary Off 2 times (double click) 5 short flashes followed by periodic flashing reset: 1 time or will reset automatically after 2 minutes uto Set Range djustment 2 times (double click) and then 1 time for 5 seconds 5 short flashes followed by 4 short flashes 3

4 MODEL EF-225 ONLY Functions RED HOT End Position WHITE Tempered Position LUE Cold End Position Setting rightness of Illumination Remove cover. Press button for approximately 5 seconds. C When illuminant glows PURPLE, release D djust the illumination by turning the E Press button once. mixing lever to desired brightness. 4 F Replace top cover.

5 MODEL EF-225 ONLY Calibrating the illuminant colors (RED - WHITE - LUE) to water temperature Remove cover. Press button twice and release. C Illuminant flashes red. D djust mixing lever for position RED (hot) and press button once. E Illuminant flashes WHITE. F djust mixing lever for position WHITE (temperate) and press button once. G Illuminant flashes LUE. H djust mixing lever for position LUE (cold) and press button once. I Replace cover. 5

6 SENSOR RNGE DJUSTMENT FCTORY SETTING IS PPROPRITE FOR THE MJORITY OF PPLICTIONS ND SHOULD NOT REQUIRE RESETTING UNLESS UNDER EXTREME SITUTIONS. 4x 2x + 1x 5 sec C 1 x ( 1x, 2x,...,8x) D 8x 7x 6x = factory setting 5x 4x 3x 2x 1x DISCLIMER: Updated electronics have visible red and green LED. Original electronics have only red LED and range setting is reversed (1=longest, 8=shortest) E F G 6

7 ... 2 x 12/24 LINE PURGE FETURE This feature will operate the faucet every 12 or 24 hours since last use, if not used to prevent stagnant water conditions. Default purge duration is two minutes. Consult factory regarding other timing options. 1x 24 sec +... C... 2 x ctivate 12HR... 3 x... 3 x ctivate 24HR D... 1 x Deactivate HOT LIMIT STOP DJUSTMENT... 1 x C... 2 x... 3 x OPERTION s the user s hands enter the beam s effective range, the beam is reflected back into the sensor receiver and activates the solenoid valve allowing water to flow from the faucet. Water will flow until the hands are removed or until the faucet reaches its automatic time out limit setting x CRE ND CLENING DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to clean Faucets that may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom tile, protect the Faucet from any splattering of cleaner. cids and cleaning fluids will discolor or remove chrome plating. 7

8 TROULESHOOTING GUIDE 1. Problem: Faucet does not function. Cause: dhesive packaging label affixed over sensor eye. Solution: Remove adhesive label from sensor eye. Cause: "Permanent Off" activated. Solution: Press button on faucet throat one time. 2. Problem: Faucet delivers water in an uncontrolled manner. Cause: Faucet is defective. Solution: Contact the Sloan Valve Company Installation Engineering Department (see below). 3. Problem: Faucet does not deliver any water when Sensor is activated. Indicator: Solenoid valve produces an audible CLICK. Cause: Water supply stop(s) closed. Solution: Open water supply stop(s). Cause: Water supply stop strainer(s) clogged. Solution: Remove, clean, and reinstall water supply stop strainer(s).replace strainer(s) if required. Indicator: Solenoid valve DOES NOT produce an audible CLICK. Cause: attery low (battery operated models). Solution: Replace battery (refer to attery Replacement on Page 3). Cause: Power failure (EF-200 Models). Solution: Check power supply. 4. Problem: Faucet delivers only a slow flow or dribble when Sensor is activated. Cause: Water supply stop(s) are partially closed. Solution: Completely open water supply stop(s). Cause: Water supply stop strainer(s) clogged. Solution: Remove, clean, and reinstall water supply stop strainer(s). Replace strainer(s) if required. 4. Problem: Faucet delivers only a slow flow or dribble when Sensor is activated. Cause: erator is clogged. Solution: Remove, clean, and reinstall erator. Replace erator if required. Cause: Faucet is defective. Solution: Contact the Sloan Valve Company Installation Engineering Department (see below). 5. Problem: Faucet does not stop delivering water or continues to drip after user is no longer detected. Cause: Valve is defective. Solution: Contact the Sloan Valve Company Installation Engineering Department (see below). 6. Problem: LED indicator blinks when faucet is in use. Cause: attery low (battery operated models). Solution: Replace battery (refer to attery Replacement on Page 3). 7. Problem: The water temperature is too hot or too cold on a faucet connected to hot and cold supply lines. Cause: Supply Stops are not adjusted properly. Solution: djust Supply Stops. Cause: For models with integral mixing valve Mixing valve is set improperly for the water temperature desired. Solution: Rotate mixing valve handle clockwise to decrease water temperature or counterclockwise to increase water temperature. When assistance is required, please contact Sloan Valve Company Installation Engineering Department at: SLON-14 ( ) PRTS LIST 1 14 Item # Part # C 3D 11 5 Description 2 2 2C 1 EF-14- Faucet Sensor ssembly (EF-275 only) EF-19- Faucet Sensor ssembly (EF-200 and EF-225 only) EF-21- Faucet Sensor ssembly (EF-250 only) EF-16- Faucet Sensor ssembly with i.q.-click (EF-275 only) EF-18- Faucet Sensor ssembly with i.q.-click (EF-200 and EF-225 only) EF-20- Faucet Sensor ssembly with i.q.-click (EF-250 only) 2 EF-1006 Cap with Solar Cell ssembly (EF-275 only) 2 EF-27 Cap (EF-250 and EF-200 only) 2C Cap (EF-225) 3 EF gpm (1.9 Lpm) VR Pressure Compensating Spray Head 3 EF gpm (5.6 Lpm) Pressure Compensating erated Stream 3C EF gpm (8.3 Lpm) erator Spray Head 3D EF gpm (8.3 Lpm) Laminar Flow Spray Head 4 EF-1003 attery Replacement Kit 5 EF-1 Faucet Mounting Kit 6 EF-9 Strainer (Filter) 7 EF-1004 Mixer Handle ssembly and Cartridge 7 EF-1005 Handle Repair Kit 8 EF-1007 Handle Cap 9 EF (330 mm) Flexible Supply Hose 10 EF-44 Power Splitter 11 EF /16 (300 mm) Extension Cable EF /4 (1200 mm) Extension Cable EF (3200 mm) Extension Cable 12 ETF-312- Trim Plate for 4 Centerset Sink 13 ETF-510- Trim Plate for 8 Centerset Sink 14 EF-11 Plug-in dapter (Models EF-200/225) 15 EF-2 Solenoid EF-44 replaces the separate EF-23- Splitter Cable and EF-28 Capacitor, which is sold separately. The information contained in this document is subject to change without notice. SLON VLVE COMPNY SEYMOUR VENUE FRNKLIN PRK, IL Phone: or Fax: or Copyright 2010 SLON VLVE COMPNY Code No: Rev. 4 (12/10)