Side Delivery Unit Installation

Transcription

1 Side Delivery Unit Installation CONTENTS Mounting Location... 1 Minimum Cabinet Size Requirements... 1 Mounting Requirements... 1 Regulator Installation... 2 Cabinet Mount Bracket Installation... 2 Wall Mount Bracket Installation... 3 Bracket Installation... 4 Unit Arm Installation... 5 Stop Pin Installation... 5 Flex Arm Lock Activation & Leveling... 6 Tubing Connections... 7 Dimensions, Range of Motion... 8 Electrical Requirements: 24VAC, 3.2 amp 13VAC, 2.0 amp Mounting Location Minimum Cabinet Size Requirements (Side Delivery) 55 to 61 in. (139.7 to cm) Verify desired position (ex. RH / LH) with proper personnel before installation. Short Flex Arm 17 in. ( 43.2 cm) 27.5 in. ( 69.8 cm) Short Flex Arm 28 in. ( 71.1 cm) 36 in. ( 91.4 cm) Flex Arm Fixed Arm 12 to 24 in. (30.4 to 60.9 cm) Mounting Requirements Mounting Structure The mounting structure must be capable of supporting the weight / torque listed below without deflection: Unit / Arm Assembly Weight (Maximum) lbs (22.6 kgs.) Torque (Maximum) ft-lbs. (231.5 N M) To prevent the unit from drifting, the mounting plate must deflect no more than 1/16" (1.6 mm) over a 12" (30.5) distance Rev. LA1 (9/17)

2 Regulator Installation Step 1: Insert regulator assembly into compression fitting of shut-off. Tighten compression fitting. WATER REGULATOR Compression Fitting AIR REGULATOR Compression Fitting Shut off Valve Regulator Shut off Valve Regulator Cabinet Mount Bracket Installation (Cabinet Mount Units Only) Midmark Freestanding Center Console cabinets are pre-drilled and it is not necessary to do the following step. Step 1: Using the below dimensions, mark position of four mounting holes for bearing plate. Use a 1/4" drill bit to drill holes. Left Hand Cabinet Mount The bearing plate can be mounted with the needle bearing at the top or bottom. It is recommended that the needle bearing is positioned at the Top. Right Hand Cabinet Mount 3-5/8" (9.2 cm) 14 3/4" (37.5 cm) Needle on Bottom. 8.0" (20.3 cm) Needle on Top. 2-3/4" (6.9 cm) 2

3 Cabinet Mount Bracket Installation (continued) (Cabinet Mount Units Only) Step 3: Loosen bolts and level bearing mounting plate. Use shims, if necessary, then tighten bolts. Backing Plate is not required on Midmark Freestanding Center Console Cabinets. Level Backing Plate Step 2: Align mounting holes and install appropriate mounting bolts. Bolts are provided in 1" and 2 1/4" lengths. Plate Shim Wall Mount Bracket Installation (Wall Mount Units Only) Wall mounted units may be mounted at any height. Verify position with proper personnel. The bearing plate can be mounted with the needle bearing at the top or bottom. It is recommended that the needle bearing is positioned at the Top. Needle on Top. 16-7/16" (41.7 cm) 21-11/16" (55 cm) Floor 66-5/8"(169.3 cm) Long Fixed & Flex Arms 48-1/8"(122.3 cm) Short Fixed & Flex Arms Product can be configured to use either Fixed Arm with either Flex Arm. 3

4 Wall Mount Bracket Installation (Wall Mount Units Only) Equipment Alert Mounting Holes MUST be aligned with wall studs. Failure to comply could cause delivery unit to fall and damage unit and wall structure. Wall Studs Step 1: Locate wall studs. Align 8 holes in mounting plate with studs. Mark and drill pilot holes (Use 1/4" drill bit). Step 3: Install mounting cover using 4 #10-32 x 3/8" screws. Step 2: Secure frame to wall with 8 (5/16"x 2 1/2") lag screws. Bracket Installation The bearing plate can be mounted with the needle bearing at the top or bottom. It is recommended that the needle bearing is positioned at the Top. Level Frame Cover Step 2: Loosen bolts and level bearing mounting plate. Use shims, if necessary, then tighten bolts. Needle Step 1: Align mounting holes in bearing plate and frame cover. Install four screws Plate Shim 4

5 Unit Arm Installation (Cabinet & Wall Mount Units) Step 2: Apply lubricant, supplied with arm assemby, to Fixed Arm. Equipment Alert All pivots points must be secure when installing unit arm. Failure to comply could result in equipment damage. Step 4: Adjust drag by loosening / tightening set screw. Step 6: Install bearing cover. Cover Step 1: Loosen set screw. Set Screw Step 7: Install water bottle. Step 5: Trim umbilical sleeve. Slide sleeve over tubing & wiring. Install and secure umbilical retainer. Stop Pin Installation (Cabinet & Wall Mount Units) Retainer Step 3: Route umbilical tubing thru bearing and slide Fixed Arm into bearing. Step 8: Connect tubing. (Refer to Tubing Diagram). Step 2: Lift trim ring. Trim Ring Rotation Stop Screw Stop Pin Trim Ring Rotation Stop Screw Stop Pin Stop Pin Fixed Arm The stop pins can be placed in two positions, as determined by rotational stop screw. Verify desired position with customer. Position A Position B Step 3: Rotate flex arm to desired position and install stop pins. Flex Arm Step 1: Position Flex and Fixed Arms as shown. 5

6 Flex Arm Lock Activation / Leveling the Delivery Unit. The following procedures should be performed after installation of entire operatory is complete. To activate flex arm lock... A. Remove end cap. B. Slide cover back to access locking pawls. C. Cut and remove wire tie. D. Slide cover in position and install end cap. Locking Pawls Wire Tie Button Head Screws Leveling Screws To level the delivery unit... A. Remove bottom cover. B. Slightly loosen button head screws. C. Adjust leveling screws until delivery unit is level. D. Tighten button head screws. E. Install cover. DA115102i 6

7 Tubing Connections 30 PSI 80 PSI 7

8 Dimensions, Range of Motion in. ( 31.7 cm) Short Flex Arm 8.3 in. ( 21.1 cm) 180 Max.* 66.6 in. (169.3 cm) Min.** 48.2 in. (122.3 cm) Short Fixed Arm 13.5 in. ( 34.3 cm) 24 in. ( 60.9 cm) Short Fixed Arm 13.5 in. ( 34.3 cm) Long Fixed Arm 24 in. ( 60.9 cm) 180 Short FlexArm 16 in. ( 40.6 cm) 24 in. ( 60.9 cm) 135 Max.* 66.6 in. (169.3 cm) Min.** 48.2 in. (122.3 cm) 135 Short Flex Arm 16 in. ( 40.6 cm) 24 in. ( 60.9 cm) * Measurement w/ long fixed arm & long flex arm (Standard w/ wall mounted unit ).] ** Measurement w/ short fixed arm & short flex arm (Standard w/ cabinet mounted unit). Product can be configured to use either fixed arm w/ either flex arm. Midmark Corporation 60 Vista Drive P.O. Box 286 Versailles, OH Fax