PR/80000, PR/80000, R/80000, R/80000 > ø 2... 00 mm > High performance adaptive cushioning system CS > High performance, stability and reliability Technical features Medium: Compressed air, filtered, lubricated or non-lubricated Standard: ISO 5552 Note: all models conform to the mentioned standards except the cylinder length Operation: Single acting, adjustable cushioning Operating pressure: ø 2... 00 mm 2... 0 bar (29... 5 psi) Ports: G/8... /2 Cylinder diameters: 2, 0, 50, 6, 80, 00 mm Standard strokes: 25, 50, 80, 00 mm Non-standard strokes: vailable (5... 250 mm) Operating temperature: ø 2... 00 mm Standard version -20... +80 C max. (-... +76 F) ir supply must be dry enough to avoid ice formation at temperatures below +2 C (+5 F). Standard Materials: Barrel: nodised aluminium End covers: Pressure diecast aluminium Piston rod: Stainless steel (martensitic) Piston rod seals: PUR O -rings: NBR Technical data Cylinder ø (mm) 2 0 50 6 80 00 Profile barrel Round barrel Port size G/8 G/ G/ G/8 G/8 G/2 Piston rod ø (mm) 2 6 20 20 25 25 Piston rod thread M0 x,25 M2 x,25 M6 x,5 M6 x,5 M20 x,5 M20 x,5 Cushion length (mm) 20 22 26 Cushioning daptive cushioning systems CS Cushioning (adjustable cushion) Initial cushion volume (cm ) 2,8 20,2 6 6 25 PR/80000/M, PR/80000M Theoretical thrusts at 6 bar outstroke (N) 92 68 0 75 2795 92 F (N) 50 60 75 75 0 0 R/80000/M, R/80000M Theoretical thrusts at 6 bar instroke (N) 528 85 56 250 97 F (N) *) 50 60 75 75 0 0 F = Final retrun force of spring The function The new CS daptive Cushioning System provides a high performance pneumatic damping function. The system will automatically cushion for a wide range of general applications as delivered. Manual adjustment is still possible for extreme applications. Only adjust the cushion needle in extreme applications. Mass (kg) [kg] Operating area of the CS daptive Cushioning System djustment in this zone not necessary. Speed (v) [v] without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.0
PR/80000, PR/80000, R/80000, R/80000 Design and sizing in pneumatics Golden Rules Design and sizing in pneumatics is often based upon experience coupled with an element of fear of under specifying crucial equipment. In an attempt to ensure enough power, engineers may select over sized cylinders and then select over sized valves to supply them with enough air. The same uncertainty can also lead to over sized specification of air line equipment, fittings and tubing. The outcome is components larger than necessary that use too much compressed air and waste energy and money. However when following some well proven golden rules and a few laws of pneumatics it is easy to achieve correctly sized pneumatic installations. Basics to Consider The force required, the pressure available, the speed of movement and air consumption. ISO and VDM standard or compact style also cushioning and sensors. Cylinders are greased on assembly and operate under normal conditions without additional lubrication. However using a lubricator will extend the life of these products. Golden Rule: The theoretical force of the cylinder should be 25% extra for high speed, 50% extra for low speed and 00% extra for ultra low speed (positioning) applications. The correct sizing is based upon the required force and applied pressure. Go to page for more information on cylinder sizing and air consumption. en..220.02 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
PR/80000, PR/80000, R/80000, R/80000 dditional ISO 5552 Cylinder ranges Symbols Profile barrel Round Barel Industrial utomation Food & Beverage Rail utomotive TEX II 2GD CE-marked ø (mm) Range Discription Datasheet Double cting _5_220_PR_802000_M_R_8000_M 2... 25 PR/802000 Cylinder _5_225_PR_802000_M_EX Double cting _5_220_PR_802000_M_R_8000_M 2... 25 R/802000 Cylinder _5_225_PR_802000_M_EX _5_220_PR_802000_M_R_8000_M Double cting 60... 20 R/8000 Cylinder _5_26_R_8000_M_EX _5_27_K_8000_M Stainless steel 2... 200 K/8000 Cylinder _5_28_K_8000_M_EX _5_20_PR_822000_M Smooth Line 2... 00 PR/822000 Cylinder _5_25_PR_822000_M_EX Clean Line _5_0_PR_82000_M 2... 00 PR/82000 Cylinder _5_5_PR_82000_M_EX _5_250_PR_862000_M 7 2... 00 PR/862000 IVC Industrial Cylinder _5_255_PR_862000_M_EX _5_260_PR_882000_M 7 2... 00 PR/882000 IVC Clean Line Cylinder 7 _5_265_PR_882000_M_EX _9_05_PS_82000_F PS/82000/ Cylinder with 0... 25 F position sensor _9_052_PS_82000_F_EX Datasheet (standard) Cylinder with 60... 20 S/8000/F position sensor _9_062_S_8000_F_EX 2... 00 PR/80000, PR/80000 Standard Single cting Cylinder 220_PR_80000_80000-2... 00 R/80000, R/80000 Standard Single cting Cylinder 220_PR_80000_80000 - Range available For additional information please contact the technical service or http://www.imi-precision.com Cylinder ranges in the frame are shown in this data sheet. without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.0
PR/80000, PR/80000, R/80000, R/80000 Cylinder variants Symbol Piston Rod Material Standard Model with ø Description Page Please see the description below R S C D Male Piston Rod Thread Female Piston Rod Thread (mm) X PR/80000/M PR/80000/MX 2... 00 Standard Cylinder Sprung in (Profile barrel) 8 X R/80000/M R/80000/MX 2... 00 Standard Cylinder Sprung in (Round barrel) 8 X PR/80000/N2 PR/80000/N2X 2... 00 X R/80000/N2 R/80000/N2X 2... 00 Cylinder with Non-Rotating Piston Rod Sprung in (Profile barrel) Maximum Stroke: 250 mm Cylinder with Non-Rotating Piston Rod Sprung in (Round barrel) Maximum Stroke: 250 mm 0 0 X PR/80000/M PR/80000/MX 2... 00 Standard Cylinder Sprung out (Profile barrel) X R/80000/M R/80000/MX 2... 00 Standard Cylinder Sprung out (Round barrel) X PR/80000/MU PR/80000/MUX 2... 00 X R/80000/MU R/80000/MUX 2... 00 X PR/80000/N2 PR/80000/N2X 2... 00 X R/80000/N2 R/80000/N2X 2... 00 Cylinder with Extended Piston Rod Sprung out (Profile barrel) Maximum extention: 00 mm Cylinder with Extended Piston Rod Sprung out (Round barrel) Maximum extention: 00 mm Cylinder with Non-Rotating Piston Rod Sprung out (Profile barrel) Maximum Stroke: 250 mm Cylinder with Non-Rotating Piston Rod Sprung out (Round barrel) Maximum Stroke: 250 mm Note: Piston Rod Material: C = Hard chromium plated; D = Stainless steel (austenitic) & hard chromium plated; R = Stainless steel (martensitic); S = Stainless steel (austenitic); X = Standard; = Option en..220.0 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
PR/80000, PR/80000, R/80000, R/80000 Option selector Standard Round barrel Profile barrel Piston rod material Stainless steel (martensitic) Stainless steel (austenitic) Hard chromium plated Stainless steel (austenitic) & hard chromium plated Cushioning Substitute None P Substitute R S C D Substitute Sprung in (ø 2... 00 mm) 0 Sprung out (ø 2... 00 mm) 0 Cylinder ø (mm) 02, 00, 050, 06, 080, 00 Variants ø 2... 00 mm (magnetic piston) Standard Non-rotating piston rod (internal) Extended piston rod **/80***/MU/***/*** Substitute Substitute M N2 MU Extension (mm) /8 / / Strokes (mm) 5... 250 Piston rod thread Male Female Substitute Substitute None Note: If postion ist not required, disregard option position within part number e.g. R/8002/M/25. For combinations of cylinder variants consult our technical service. For example: Please note that heat resistant seals are not available for all variants. This option selector explains only the cylinder variants. dditional variants/options are not possible. Detail s see table on page. X without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.05
7 PR/80000, PR/80000, R/80000, R/80000 Cylinder with Profile barrel ø 2... 00 mm 2 Mountings Model 5 K 6 7 7 22 7 2 8 26 6 2 27 0 28 7 2 9 Page B, G C 0 D2 F FH 9 8 9 20 68 079 65677678587896980 2 22 2 5 2556 957090 2 5 6 H 7 8 9 0 2 8 0 9 202 Page Page Page 5 Page 5 Page 5 Page 5 Page 6 QM/802/5 QM/8025/8 Q/802/22 Q/802/2 Q/802/2 Q/802/2 QM/8025/25 Q/802/ Q/802/28 25 20 27 28 29 20 2 22 2 25 5 6 7 82026 9 27 20 2820 292 2 2 2 2 52 5 5 6 6 5 6 7 7 6 7 8 8 7 8 9 9 8 9 20 20 9 20 QM/802/5 29 5 6 QM/800/8 Q/800/22 Q/800/2 Q/800/2 Q/800/2 QM/800/25 Q/800/ 22 28 729 2020 2 2 20 2 22 22 2 22 220 2 22 2 2 2 25 25 25 26 26 25 26 27 27 26 27 28 28 27 28 29 29 28 29 0 7 8 209 2 2 25 26 527296 50 QM/8050/5 QM/8050/8 80 QM/8080/5 00 QM/8080/5 6 8 UH Page 9 QM/8050/5 UH 6 US Groove key Valve mounting kit QM/8080/25 Q/8080/ QM/8080/8 Q/800/22 Q/800/2 Q/800/2 Q/800/2 QM/8080/25 SW UF UR SS 2 7 2 8 9 5 20 56 5 6 22 Page 6 Page 6 67 7 8 8 9 2 90 0 5 6 7 8 2 9 0 52 Page 7 Page 7 Page 7 Page 7 Page 8 Page 8 Page 8 20 5 2 6 22 7 2 8 9 25 26 27 2027 28 2 22 2 25 26 207 27 28 28 229 29 2 20 2 22 2 2829 29 202020 2 25 2 26 5 6 7 8 9 20 2 5 6 7 8 9 20 2 5 5 6 6 7 8 9 PQ/80202/0 2 Q/802/ M/P99 QM/8025/2 Q/802/ Q/802/27 M/P99 M/P00 M/P7286 2 0 50 M/P99 QM/800/2 Q/800/ M/P992 M/P0 M/P7286 205 26 22 2 25 26 27 28 29 20 2 22 20 PQ/80200/0 2 22 2 25 26 27 28 29 20 2 22 2 2 25 25 26 27 28 0 0 07 026 02929 Q/800/ 2 2 5 6 7 8 2 5 6 7 27 8 228 9 89 9Q/800/27 Q/8080/27 M/P995 M/P0 M/P7286 Q/800/ Q/800/27 M/P996 M/P05 M/P7286 2 25 22 26 2 27 28 25 22 5 2 6 7 8 5 Q/806/ M/P997 PQ/80200/0 Q/800/ M/P998 Pos. Style Standard Pos. Style Standard Pos. Style Standard B, G Clear anodised aluminium 8 D2 5 F 2 C Galvanized steel (ø 2... 00 mm) R Die-cast aluminium Painted cast iron Bolt: stainless steel (martensitic) Circlip: galvanized steel Galvanized steel Bolt: galvanized steel Circlip: Galvanized steel UR Galvanized aluminium Inner ring: steel Outer ring: brass 9 FH Cast iron 6 SS Painted cast iron 0 Galvanized steel 7 UF H Cast iron 2 S Clear anodised aluminium Bearing: brass Galvanized steel, Inner ring: steel Outer ring: brass 8 K Galvanized steel Valve mounting kit Galvanized steel 20 UH Cast iron UH nodised aluminium Groove key Steel en..220.06 Q/8080/ QM/8080/2 9 6 PQ/802080/0 82 5 60 7 M/P996 QM/8050/2 Die-cast aluminium Bolt: galvanized steel (martensitic) Circlip: galvanized steel Galvanized aluminium Inner ring: steel Outer ring: brass QM/8080/2 8 5 00 US M/P7286 7 80 7 M/P02 6 Page 26 & 27 0 PQ/80206/0 2 Die-cast aluminium M/P99 7 6 SW Q/8050/27 96 QM/8050/2 6 Q/8050/ 85 M/P995 D 7 Q/800/ 5 5 6 PQ/802050/0 Q/806/ 0 9 5 25 2 26 27 28 29202 5220 6 75 5 865 6 9760 78728989209 00 65 29 76 6 872 7 988 0 5 5 2 2 2 ø Q/802/0 Q/800/0 Q/8080/2 Page 6 22 0 2 2 25 2 Q/8080/0 Q/8080/2 7 20 2 5 22 6 2 Q/800/28 Q/8080/2 2 6 Q/800/ Q/8080/22 0Q/806/22 00 0 6 8 9 2 2 2 0 2 52 5 5 6 6 5 6 7 7 6 7 85 8 7 8 9 9 8 979 Q/806/ Q/806/2 Q/806/2 Q/806/2 QM/8050/25 9 5 Q/806/0 QM/8080/8 8 2 Q/8080/28 Q/8050/ 7 Q/806/28 QM/8050/25 5 Q/8050/0 Q/8050/2 R Q/800/0 2 Q/8050/2 S 2 Q/8050/28 Q/8050/2 QM/8050/8 0 9 8Q/800/28 Q/8050/22 2 D 8 + 20 6 8 ø 95 0 6 Cylinder with Round barrel ø 2... 00 mm 00 Q/806/27 52 6 7 85 6 9 2 99 9 5 6 77 88 Q/806/ M/P99 M/P0 M/P7286 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH More Details see page 26 & 27
PR/80000, PR/80000, R/80000, R/80000 ccessories for Profile (ø 2... 00 mm) & Round barrel (ø 2... 00 mm) Model Profile barrel Model Round barrel Port size Banjo flow control Straight fitting Elbow fitting Sevice kit Service kit for Round and Profile barrel ø PR/80*02/M/* R/80*02/M/* 2 G/8 C0K5068 C0225068 C07068 PR/80*00/M/* R/80*00/M/* 0 G/ C0K50628 C02250628 C070628 PR/80*050/M/* R/80*050/M/* 50 G/ C0K50828 C02250828 C070828 PR/80*06/M/* R/80*06/M/* 6 G/8 C0K5088 C0225088 C07088 PR/80*080/M/* R/80*080/M/* 80 G/8 C0K508 C022508 C0708 PR/80*00/M/* R/80*00/M/* 00 G/2 C0K58 C02258 C078 For alternative fitting types please contact the technical service. ø 2 Q/802/00 0 Q/800/00 50 Q/8050/00 6 Q/806/00 80 Q/8080/00 00 Q/800/00 Magnetically operated switches M/50/** Groove cover Switch mounting brackets for M/50 TQM/, QM/2, QM/2 Switch mounting brackets for TQM/, QM/2, QM/2 QM/0 Switch mounting brackets for QM/0 2 ø Page 9-22 Page 8 Page 22 Page 2 Page Page 25 Page 26 2 M/P72725/000 QM/27/2/ QM//02/22 QM/0/00/22 0 M/P72725/000 QM/27/2/ QM//02/22 QM/0/00/22 50 M/P72725/000 QM/27/2/ QM//02/22 QM/0/00/22 6 M/P72725/000 QM/27/2/ QM//02/22 QM/0/00/22 80 M/P72725/000 QM/27/2/ QM//080/22 QM/0/00/22 00 M/P72725/000 QM/27/2/ QM//080/22 QM/0/00/22 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.07
RT RT U2 B MM KK B TG E U PR/80000, PR/80000, R/80000, R/80000 Basic dimensions PR/80000/M, R/80000/M Standard Cylinder Sprung in Dimensions in mm Projection/First angle ZJ + # I8 + # KW I2 WH I2 VD PL G l7 EE G PL V E TG KV SW EE I BH BG 2 BG BH Model Profile barrel ø 2... 00 mm Model Round barrel ø 2... 00 mm # Stroke Cushion screw 2 ø 80... 00 mm M/50 switches can be mounted flush with the profile For additional information please contact the technical service or http://www.imi-precision.com en..220.08 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
PR/80000, PR/80000, R/80000, R/80000 ø -0,5 ø B ø B BG E EE G KK KW L2 L L7 L8 L2 ø MM PL TG d d min BH KV h9 2 22 0 0 6 6 7 G/8 29 M0 x,25 7 5 9,5 6,6 9 + (N *28) 5,5 2 5 2,5 0 5 5 6 6 5 G/,5 M2 x,25 9 6 22 5,6 0 + (N *28) 6,5 6 2,5 8 50 2 0 0 6 8 65 G/ M6 x,5 8 25 5,6 + (N *28) 8 20 22,7 6,5 6 2 5 5 6 8 75 G/8 6,5 M6 x,5 8 25 5,6 6 + (N *28) 8 20,2 56,5 80 0 5 5 7 9 95 G/8 2 M20 x,5 0 0 -,8 5 + (N *28) 0 25 29,7 72 00 0 55 55 7 9 G/2 2 M20 x,5 0 0 5 -,8 6 + (N *28) 0 25 27,7 89 ø RT SW U U2 V VD WH ZJ Model Profile barrel at 0 mm per 25 mm Model Round barrel 2 M 6 0,6 6,,5 6 26 5 + (N *28) PR/8002/M/* 0,9 (kg) 0,5 (kg) R/8002/M/* 0,6 (kg) 0,6 (kg) 0 M 6 5,8 9,2,5 6 0 60 + (N *28) PR/8000/M/* 0,69 (kg) 0,22 (kg) R/8000/M/* 0,65 (kg) 0,2 (kg) 50 M 8 7 8,7 0,8,5 6 7 68 + (N *28) PR/80050/M/*,09 (kg) 0, (kg) R/80050/M/*,02 (kg) 0,2 (kg) 6 M 8 7 0 2,8,5 6 7 8 + (N *28) PR/8006/M/*,5 (kg) 0,5 (kg) R/8006/M/*,6 (kg) 0,6 (kg) 80 M 0 22 2,5,5 6 6 99 + (N *28) PR/80080/M/* 2,6 (kg) 0,62 (kg) R/80080/M/* 2,5 (kg) 0,6 (kg) 00 M 0 22 9,5,5 6 5 + (N *28) PR/8000/M/*,66 (kg) 0,72 (kg) R/8000/M/*,50 (kg) 0,7 (kg) * Please insert stroke length; Basic Dimension are also for cylinder varinats or for different piston rod material at 0 mm per 25 mm Hub (stroke) RT Note <= 50 N = 0 > 50 N = Hub (stroke) 50 - round up to integer without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.09
MM D KF PR/80000, PR/80000, R/80000, R/80000 Cylinder variants PR/80000/MX, R/80000/MX Cylinder with Female Piston Rod Thread Sprung in Dimensions in mm Projection/First angle I2 SW T2 F T ø F ø D KF l2 ø MM h9 SW T T2 2 2 6, M6 5,5 2 0 6 2,6 0 2 8, M8 6,5 6 6, 50 6 0,5 M0 8 20 7 2,7 6 6 0,5 M0 8 20 7 2,7 80 20 M2 0 25 22 25 6, 00 20 M2 0 25 22 25 6, For missing dimensions please see page 8 and 9 Cylinder variants PR/80000/N2, R/80000/N2 Cylinder with Non-Rotating Piston Rod Sprung in PR/80000/N2X, R/80000/N2X Cylinder with Non-Rotating Piston Rod and Female Piston Rod Thread Sprung in SW ø SW max. Torque (Nm) Model Profile barrel Model Round barrel 2 0 0,5 PR/8002/N2/* R/8002/N2/* 0 PR/8000/N2/* R/8000/N2/* 50 6,5 PR/80050/N2/* R/80050/N2/* 6 6,5 PR/8006/N2/* R/8006/N2/* 80 2 2,5 PR/80080/N2/* R/80080/N2/* 00 2 2,5 PR/8000/N2/* R/8000/N2/* * Please insert stroke length; Maximum Hub: 250 mm; For missing dimensions please see page 8 and 9 en..220.0 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
RT B E PR/80000, PR/80000, R/80000, R/80000 Basic dimensions PR/80000/M, R/80000/M, PR/80000/MU, R/80000/MU Standard Cylinder Sprung out Dimensions in mm Projection/First angle ZJ + 2*Hub (stroke) + $ I8 + Hub (stroke) KW I2 WH + Hub (stroke) + $ G I2 PL I7 VD EE G PL V E TG KV RT MM KK U2 U B TG SW EE I BH BG 2 BG BH Model Profile barrel ø 2... 00 mm Model Round barrel ø 2... 00 mm # Stroke $ Piston rod extension Cushion screw 2 ø 80... 00 mm M/50 switches can be mounted flush with the profile For additional information please contact the technical service or http://www.imi-precision.com without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.
PR/80000, PR/80000, R/80000, R/80000 ø -0,5 ø B ø B BG E EE G KK KW L2 L L7 L8 L2 ø MM PL TG d d min BH KV h9 2 22 0 0 6 6 7 G/8 29 M0 x,25 7 5 9,5 6,6 9 + (N *28) 5,5 2 5 2,5 0 5 5 6 6 5 G/,5 M2 x,25 9 6 22 5,6 0 + (N *28) 6,5 6 2,5 8 50 2 0 0 6 8 65 G/ M6 x,5 8 25 5,6 + (N *28) 8 20 22,7 6,5 6 2 5 5 6 8 75 G/8 6,5 M6 x,5 8 25 5,6 6 + (N *28) 8 20,2 56,5 80 0 5 5 7 9 95 G/8 2 M20 x,5 0 0 -,8 5 + (N *28) 0 25 29,7 72 00 0 55 55 7 9 G/2 2 M20 x,5 0 0 5 -,8 6 + (N *28) 0 25 27,7 89 ø RT SW U U2 V VD WH ZJ Model Profile barrel at 0 mm per 25 mm Model Round barrel 2 M 6 0,6 6,,5 6 26 5 + (N *28) PR/8002/M/* 0,9 (kg) 0, (kg) R/8002/M/* 0,6 (kg) 0, (kg) 0 M 6 5,8 9,2,5 6 0 60 + (N *28) PR/8000/M/* 0,69 (kg) 0,7 (kg) R/8000/M/* 0,65 (kg) 0,7 (kg) 50 M 8 7 8,7 0,8,5 6 7 68 + (N *28) PR/80050/M/*,09 (kg) 0, (kg) R/80050/M/*,02 (kg) 0,25 (kg) 6 M 8 7 0 2,8,5 6 7 8 + (N *28) PR/8006/M/*,5 (kg) 0,28 (kg) R/8006/M/*,6 (kg) 0,29 (kg) 80 M 0 22 2,5,5 6 6 99 + (N *28) PR/80080/M/* 2,6 (kg) 0,5 (kg) R/80080/M/* 2,5 (kg) 0,5 (kg) 00 M 0 22 9,5,5 6 5 + (N *28) PR/8000/M/*,66 (kg) 0,6 (kg) R/8000/M/*,50 (kg) 0,62 (kg) * Please insert stroke length. Basic Dimension are also for cylinder varinats or for different piston rod material at 0 mm per 25 mm Hub (stroke) RT Note <= 50 N = 0 > 50 N = Hub (stroke) 50 - round up to integer en..220.2 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
PR/80000, PR/80000, R/80000, R/80000 Cylinder variants PR/80000/MX, R/80000/MX, PR/80000/MUX, R/80000/MUX Cylinder with Female Piston Rod Thread Sprung out Dimensions in mm Projection/First angle SW I2 E TG MM D KF TG E T2 F T BH ø F ø D KF l2 ø MM h9 SW T T2 2 2 6, M6 5,5 2 0 6 2,6 0 2 8, M8 6,5 6 6, 50 6 0,5 M0 8 20 7 2,7 6 6 0,5 M0 8 20 7 2,7 80 20 M2 0 25 22 25 6, 00 20 M2 0 25 22 25 6, For missing dimensions please see page 8 and 9 Cylinder variants PR/80000/N2, R/80000/N2 Cylinder with Non-Rotating Piston Rod Sprung out PR/80000/N2X, R/80000/N2X Cylinder with Non-Rotating Piston Rod and Female Piston Rod Thread Sprung out - (:) SW ø SW max. Torque (Nm) Model Profile barrel Model Round barrel 2 0 0,5 PR/8002/N2/* R/8002/N2/* 0 PR/8000/N2/* R/8000/N2/* 50 6,5 PR/80050/N2/* R/80050/N2/* 6 6,5 PR/8006/N2/* R/8006/N2/* 80 2 2,5 PR/80080/N2/* R/80080/N2/* 00 2 2,5 PR/8000/N2/* R/8000/N2/* * Please insert stroke length; Maximum stroke: 250 mm; For missing dimensions please see page 8 and 9 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.
PR/80000, PR/80000, R/80000, R/80000 Mountings Front or rear stud mounting Piston rod swivel K Dimensions in mm Projection/First angle BB L 2 T SW KK KK DD L2 B F L ø BB DD L SW T (min) (kg) Model () 2/0 7 M6 0,5 0,02 QM/802/5 50/6 2 M8 0 5 0,05 QM/8050/5 80/00 28 M0 5 5 6 0,08 QM/8080/5 ø KK B F L L2 SW (kg) Model (K) 2 2 M0 x,25 5 26 7 20 9 2 7 0 0,20 QM/8025/8 0 M2 x,25 6 26 77 9 2 9 0 0,20 QM/800/8 50/6 M6 x,5 8 06 2 0 9 2 0,65 QM/8050/8 80/00 M20 x,5 0 2 22 0 0 9 0 2 0,72 QM/8080/8 Front flange B, G Conforms to ISO 5552, type MF and MF2 Foot mounting C Conforms to ISO 5552, type MS MF UF TF FB E R T H U O ø B TR E ø E ø FB MF R TF UF (kg) Model (B, G) 2 50 7 0 2 6 80 0,0 Q/802/22 0 55 9 0 6 72 90 0,2 Q/800/22 50 65 9 2 5 90 0 0,2 Q/8050/22 6 75 9 2 50 00 25 0,27 Q/806/22 80 00 2 6 6 26 5 0,6 Q/8080/22 00 20 6 75 50 86 0,89 Q/800/22 ø ø B H O T U E TR (kg) Model (C) 2 7 2 8 8 2 0,5 Q/802/2 0 0 6 9 28 5 6 0,8 Q/800/2 50 0 5 0 5 2 6 5 0,0 Q/8050/2 6 0 50 2 5 2 7 50 0,9 Q/806/2 80 2 6 9 6 98 6 0,80 Q/8080/2 00,5 7 9 6 5 75 0,95 Q/800/2 en..220. without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
PR/80000, PR/80000, R/80000, R/80000 Rear clevis D Conforms to ISO 5552, type MP2 Rear clevis D2 Conforms to ISO 5552, type B6 Dimensions in mm Projection/First angle LH CP UB FL CG H FM CB H L SR EK e 8 B R JK h 9 MR ø CB H ø EK e8 FL L LH MR UB (kg) Model (D) 2 26 0 22 52 9 5 0, Q/802/2 0 28 2 25 6 60 2 52 0,6 Q/800/2 50 2 2 27 7 68 2 60 0,22 Q/8050/2 6 0 6 2 22 79 5 70 0, Q/806/2 80 50 6 6 22 99 5 90 0,5 Q/8080/2 00 60 20 27 9 20 0 0,90 Q/800/2 ø CG H CP B ø JK h9 FM SR R (kg) Model (D2) 2, 0 22 7 0,20 Q/802/2 0 6 0, 2 25 2 20 0,2 Q/800/2 50 2 5, 6 27,5 22 0,6 Q/8050/2 6 2 5, 6 2 8 25 0,55 Q/806/2 80 25 65, 20 6 22 0 0,90 Q/8080/2 00 25 75, 20 22 2,5 Q/800/2 Piston rod clevis F Conforms to DIN ISO 80 Front or rear detachable trunnion FH Conforms to VDM 562 part 2, type MT 5/6 L CL LE CE KK RK CL CM ø CK h UW TD e 9 R ER TL D H TM h ø KK CE ø CK h CL CM ER LE RK (kg) Model (F) 2 M0 x,25 0 0 20 0 6 20 27,5 0,09 QM/8025/25 0 M2 x,25 8 2 2 9,5 0, QM/800/25 50/6 M6 x,5 6 6 2 6 25 2 2 0, QM/8050/25 80/00 M20 x,5 80 20 0 20 2 0 5 0,67 QM/8080/25 ø ø D H L R ø TD e9 TL TM h UW (kg) Model (FH) 2 0 6 2 2 50 5 0,20 Q/802/ 0 5 20,6 6 6 6 55 0,8 Q/800/ 50 0,6 6 6 75 65 0,60 Q/8050/ 6 5,6 20 20 90 75,0 Q/806/ 80 5 28,6 20 20 0 00,90 Q/8080/ 00 55 8 2 25 25 2 20,50 Q/800/ without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.5
PR/80000, PR/80000, R/80000, R/80000 Centre trunnion H Conforms to ISO 5552, type MT Used for cylinder model with round barrel djustable trunnion mounting UH Conforms to ISO 5552, type MT Used for cylinder model with round barrel Dimensions in mm Projection/First angle R R UW ø TD e 9 UW ø TD e 9 L TL TM h L TL TM h ø L R max. ø TD e9 TL TM h UW XV min. XV max. + # (kg) Model (H) 2 20 2 2 50 50 66 80 0,6 Q/802/28 0,6 6 6 6 58 76 89 0,5 Q/800/28 50 28,6 6 6 75 70 82 98 0,65 Q/8050/28 6 28,6 20 20 90 80 88 07 0,85 Q/806/28 80 28,6 20 20 0 00 97 2,2 Q/8080/28 00 8 2 25 25 2 26 07 28 2, Q/800/28 Note: Style H : These mountings are only supplied assembled complete with the cylinder. Unless otherwise specified, units will be supplied with dimension XV min. plus half the stroke length. XV = Distance from the piston rod shoulder to the centre of the mounting (Please see drawing). Not for use on profile options. This item is suited to all loads including heavy duty loads. This item is for replacement only H mounting must be initially ordered with the cylinder. Locking screws Torque max: ø 2 & 0 mm = 6 Nm; ø 50 & 6 mm = 0 Nm; ø 80 & 00 mm = 5 Nm ø L R max. ø TD e9 TL TM h UW XV min. XV max. + # (kg) Model (UH) 2 20 2 2 50 50 65 8 0,6 Q/802/0 0,6 6 6 6 58 76,5 88,5 0,5 Q/800/0 50 28,6 6 6 75 70 8 96 0,65 Q/8050/0 6 28,6 20 20 90 80 87,5 07,5 0,85 Q/806/0 80 28,6 20 20 0 00 02 8,2 Q/8080/0 00 8 2 25 25 2 26 2 28 2, Q/800/0 Style UH : It is most important that the locking screws which secure the mounting to the tie rod are tightened to the torque figures shown in the table below. For maximum energy input, consult our Technical Service. Unless otherwise specified, units will be supplied with dimension XV min plus half the stroke length. XV = Distance from the piston rod shoulder to the centre of the mounting (Please see drawing). Not for use on profile options. This item is adjustable and suited to normal loads. djustable trunnion mounting UH Conforms to ISO 5552, type MT Used for cylinder model with profile barrel TK TL TM TL XV min. XV max. + # XV # Stroke R R øtd øtd UW ø R ø TD e9 TK max. TL h TM h UW XV min. XV max. + # (kg) Torque (Nm) Model (UH) 2 2 25 2 50 58 67,5 78,5 0,06, PQ/80202/0 0,6 6 28 6 6 65 78,5 86,5 0,, PQ/80200/0 50,6 6 28 6 75 80 8 96 0,6 PQ/802050/0 6,6 20 6 20 90 96 9,5 0,5 0,2 PQ/80206/0 80,6 20 6 20 0 6 06 0,7 6,5 PQ/802080/0 00 2 25 8 25 2 0 7 2 0,72 6,5 PQ/80200/0 Style UH : It is most important that the locking screws which secure the mounting to the tie rod are tightened to the torque figures shown in the table below. For maximum energy input, consult our Technical Service. Unless otherwise specified, units will be supplied with dimension XV min. plus half the stroke length. XV = Distance from the piston rod shoulder to the centre of the mounting (Please see drawing). This item is adjustable and suited to normal loads. Trunnion support S Conforms to ISO 5552, type T ø D 2 B ø D T H 2 H H7 ø D C B 2 F x 5 ø B C ø ø ø F x H T (kg) Model 2 DH7 D2 D 5 2 (S) 2 2 6 8 0,5 2 6,6 0 5 6,8 0,0 Q/802/ 0/50 6 55 2 2 6 9 5,6 6 8 9 0, Q/800/ 6/80 2 65 2 20 8,6 0 20 0,8 Q/806/ 00 50 75 28,5 6,5 25 20 2 50 25 0, Q/800/ en..220.6 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
PR/80000, PR/80000, R/80000, R/80000 Universal piston rod eye UF Conforms to DIN ISO 89 Universal rear eye UR Conforms to ISO 5552, type MP6 Dimensions in mm Projection/First angle CE EX DL CN H 7 EN h2 KK CX H 7 Z Z Z Z R ER LE EP MS ø Thread KK CE ø CN H7 EN h2 ER LE Z (kg) Model (UF) 2 M0 x,25 20 0 5 9 0,09 QM/8025/2 0 M2 x,25 22 50 2 6 6 7 0, QM/800/2 50/6 M6 x,5 28 6 6 2 2 22 5 0, QM/8050/2 80/00 M20 x,5 77 20 25 25 26 5 0,67 QM/8080/2 ø ø CX H7 EX MS DL R Z (kg) Model (UR) 2 0 6 22 0,5 Q/802/ 0 2 6 8 25 6 0,25 Q/800/ 50 6 2 2 27 9 5 0,0 Q/8050/ 6 6 2 2 2 22 5 0,55 Q/806/ 80 20 25 28 6 0,90 Q/8080/ 00 20 25 0 27,50 Q/800/ Wide hinge SW Conforms to ISO 5552, type B7 Rear eye R Conforms to ISO 5552, type MP ø CK H 9 EM EW FL L ø EB CD H 9 L 2 BR GL BT PH ø HB TE UL R UR MR ø BR BT PH ø CK H9 ø EB EM GL 2 0 7 2 0 2 25,6 2 0 9 6 2 2 7,6 50 5 2 5,6 6 5 50 6 5 9,6 7 80 5 6 6 8 9,6 7 00 8 5 7 20 8 59,6 55 ø ø CD H9 EW FL L MR (kg) Model (R) 2 0 25,6 22 9 0,09 Q/802/27 0 2 27,6 25 6 2 0, Q/800/27 50 2,6 27 7 2 0,7 Q/8050/27 6 6 9,6 2 22 5 0, Q/806/27 80 6 9,6 6 22 5 0,7 Q/8080/27 00 20 59,6 27 20 0,59 Q/800/27 ø ø HB L2 R TE UL UR (kg) Model (SW) 2 6,6,6 8 8 50 0,05 M/P99 0 6,6,6 22 5 5 0,07 M/P99 50 9,6 0 50 65 5 0, M/P995 6 9,6 5 52 67 50 0,8 M/P996 80 2,5 0 66 8 60 0,28 M/P997 00 2,5 50 76 9 70 0,2 M/P998 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.7
PR/80000, PR/80000, R/80000, R/80000 Narrow hinge SS Dimensions in mm Projection/First angle ø CK G 7 EM BR GL ø EB PH ø HB TE UL EU Z ER G Z ø D L5 H6 L 2 BT R UR CH ø BR BT ø CK G7 ø EB EM GL ø HB L2 PH R TE UL UR (kg) Model (SS) 2 0 8 0 0 2 6,6,6 2 8 8 5 0,5 M/P99 0 0 2 2 6,6,6 6 22 5 5 0,20 M/P992 50 2 6 5 6 9,6 5 0 50 65 5 0,8 M/P99 6 5 2 6 5 6 7 9,6 50 5 52 67 50 0,50 M/P99 80 5 20 8 20 7 2,5 6 0 66 86 60 0,75 M/P995 00 9 5 20 8 20 55 2,5 7 50 76 96 70,20 M/P996 Swivel hinge US Conforms to VDM 562 part 2 Groove key M/P7286 Weight: 0,0 (kg) ø CN H 7 EN -0, X 5 M ø S5 K K 2 G 2 G ø CH ø CN H7 ø D EN -0, ER EU G G2 G H6 K K2 L5 S5 Z (kg) Model (US) 2 2 0 6 0,5 2 8 0 8 5,6 6,6 0,9 M/P00 0 6 2 6 8 2 22 5 0 5,6 6,6 0, M/P0 50 5 6 5 2 2 5 0 5 2 50 65,6 9 5 0,6 M/P02 6 50 6 5 2 2 5 7 5 50 2 52 67,6 9 5 0,59 M/P0 80 6 20 8 25 28 8 7 0 60 66 86 2,5,0 M/P0 00 7 20 8 25 0 8 55 50 70 5 76 96 2,5,0 M/P05 Groove cover M/P72725/000 X X 6,8 0,8 en..220.8 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
PR/80000, PR/80000, R/80000, R/80000 > Magnetically operating reed switch - Round style > Suitable for all cylinder ranges with magnetic piston > LED indicator on LSU models > lternative variants allows a wide range of application > Switches can be mounted flush with the delivered special adaptor Technical features Operation: M/50/LSU Normally open with LED (yellow) Switching voltage (Ub): 0... 0 V a.c./70 V d.c. Switching voltage output: Ub - 2,7 V Switching current (see graph overleaf): 0,8 max. Switching power: 0 W/0 V max. Contact resistance: 50 mω Response time:,8 ms Operating temperature: -25... +80 C (- F... +76 F) High temperature version: +50 C max.(+02 F) Protection rating (EN 60529): IP 66 Shock resistance: 50 g (during ms) Vibration resistance: 5 g (at 2000 Hz) Cable type: 2 x 0,25: PVC, PUR or silikone x 0,25 PVC Cable length: 2, 5 or 0 m Electromagnetic compatibility according to: EN 6097-5-2 Materials: Body: plastic Cable: see table below Technical data - Reed switches - additional information see data sheet en..005 Symbol Voltage Current Function Operating LED Protection Plug Cable Cable Weight Model (V a.c.) (V d.c.) maximum temperature class length type (m) ( C) (m) (g) ~ + BN 0... 0 0... 70 80 Normally open -25... +80 IP 66 2, 5 or 0 PVC 2 x 0,25 7 M/50/LSU/*V 0... 0 0... 70 80 Normally open -25... +80 IP 66 5 PUR 2 x 0,25 7 M/50/LSU/5U ~ BU BN BU 0... 0 0... 70 80 Normally open -25... +50 IP 66 2 Silicon 2 x 0,25 7 TM/50/RU/2S BK BU BN 0... 0 0... 70 80 Changeover -25... +80 IP 66 5 PVC x 0,25 7 M/50/RC/5V + BN 0... 60 0... 60 80 Normally open -25... +80 IP 66 M8 x 0, PVC x 0,25 6 M/50/LSU/CP *) ~ 0... 60 0... 60 80 Normally open -25... +80 IP 66 M2 x 0, PVC x 0,25 6 M/50/LSU/CC *) ~ BK * Insert cable length; *) Plug-in connector see page without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.9
PR/80000, PR/80000, R/80000, R/80000 Dimensions M/50/LSU/*V, M/50/LSU/5U, TM/50/RU/2S Cable length L = 2, 5 or 0 m Dimensions in mm Projection/First angle -B L +0 5, 0 50 +0 -B L +0 50 +0 5, 0 ø 6, ø 6,,5 B 2 M/50/RC/5V Cable length L = 5 m,5 B M/50/LSU/CP M/50/LSU/CC -B 5, 0 00 ±5,5... 6 X BK ø 6,,5 B X BN BU ccessories Plug-in connector cable with nut Fixing screw 2 + BN = brown; - BU = blue (output) - BK = black; + BN = brown; - BU = blue Version CP: Plug M8 x, color code: BK = +; BN = -; BU = output Version CC: Plug M2 x, color code: BK = +; BN = -; BU = output Outer cover Cable length (m) Weight (kg) Connector Model PVC x 0,25 5 0,8 M8 x M/P700/5 PUR x 0,25 5 0,8 M8 x M/P7002/5 PUR x 0, 5 0,2 M2 x M/P59/5 en..220.20 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
PR/80000, PR/80000, R/80000, R/80000 > Magnetically operating Solid state - Round style > Magnetically operating switch, solid state the delivered special adaptor > Resistance, reliable switching with a very fast response time > Easy IO link Version available > Suitable for all cylinder ranges with magnetic piston > Particularly suited for use in high levels of vibration > LED indicator as standard > Switches can be mounted flush with > CE verificated > UL certificated Technical features Operation: M/50/EP (PNP) open collector output with LED (yellow) M/50/EN (NPN) grounded emitter output with LED (yellow) M/50/IOP (PNP) Easy IO link open collector output with LED (yellow) Switching voltage (Ub): 0... 0 V d.c. Switching voltage output: Ub - 2 V Inducted voltage: 0,5 V Switching current (see graph overleaf): 50 m max. Switching power:,5 W max. Response time: < 0,5 ms Operating frequency: 5 khz Protection rating (EN 60529): IP 67 (standard) IP 68 for type: M/50/EP/5U Operating temperature: -0... +80 C (-0... 76 F) (IP 67 & IP 68) Cable type: PVC x 0,2 (standard) PUR x 0, (M/50/EP/5U) Cable length: 2, 5 and 0 m Electromagnetic compatibility according to: EN 6097-5-2 Materials: Body: plastic Cable: see table below Technical data - Solid state - additional information see data sheet en..007 Symbol pnp pnp npn + + BN BU BK BN BU BK BU + BN BK Voltage (V d.c.) Current maximum (m) Function IO Link easy *2) Operating temperature ( C) LED Protection class Plug Cable length (m) Cable type Weight (g) Model 0... 0 50 PNP -0... +80 IP 67 2, 5 or 0 PVC x 0,2 7 M/50/EP/*V 0... 0 50 PNP -0... +80 IP 67 5 PVC x 0,2 7 M/50/IOP/5V 0... 0 50 PNP -0... +80 IP 68 5 PUR x 0, 7 M/50/EP/5U 0... 0 50 PNP -0... +80 IP 67 M8 x 0, PVC x 0, 6 M/50/EP/CP *) 0... 0 50 PNP -0... +80 IP 67 M8 x 0, PVC x 0, 6 M/50/IOP/CP *) 0... 0 50 PNP -0... +80 IP 67 M2 x 0, PVC x 0, 6 M/50/EP/CC *) 0... 0 50 NPN -0... +80 IP 67 2, 5 or 0 PVC x 0,2 7 M/50/EN/*V npn + BU BN BK 0... 0 50 NPN -0... +80 IP 67 M8 x 0, PVC x 0, 6 M/50/EN/CP *) * Insert cable length; *) Plug-in connector below; Color code: BK = black, BN = brown, BU = blue IO Link easy function Optical djustment Counter Temperature diagnostic Power LED without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.2
PR/80000, PR/80000, R/80000, R/80000 Dimensions M/50/IOP/5V Cable length L = 2, 5 or 0 m Dimensions in mm Projection/First angle -B L +0 2 ± 5, 0 ø 6,,5 B 2 M/50/IOP/CP -B 5, 0 00 ±5,5... 6 X BK ø 6,,5 B X BN BU M/50/EP/CC -B 00 ±5 X 5, 0 7,5 BK BU ø 6,,5 X BN ccessories Plug-in connector cable with nut Fixing screw 2 Color code: BK = black; BN = brown; BU = blue Plug M8 x Plug M2 x Outer cover Cable length (m) Weight (kg) Connector Model PVC x 0,25 5 0,8 M8 x M/P700/5 PUR x 0,25 5 0,8 M8 x M/P7002/5 PUR x 0, 5 0,2 M2 x M/P59/5 QM/27/2/ Switch mounting brackets for Round barrel Switch: M/50 ø B L Weight (kg) L Model 2 9 6 2 0,00 QM/27/2/ 0 9 7 2 0,00 QM/27/2/ 50 7 5 2 0,00 QM/27/2/ 6 7 6 2 0,00 QM/27/2/ 80 2 0,00 QM/27/2/ 00 2 2 0,00 QM/27/2/ B en..220.22 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
PR/80000, PR/80000, R/80000, R/80000 > Magnetically operating Reed switch & Solid state - Block style > Suitable for all Rond barrel cylinder with magnetic piston > lternative materials allows a wide range of application > Switch with plug Technical features Operation: TQM/, QM/2 normally open with LED (yellow) Switching voltage (Ub): 0... 0 V a.c./d.c. Switching voltage output: Ub - 2 V (QM/2) Switching current (see graph overleaf): max. (QM/2) Switching power: 50 W/50 V max. Contact resistance: 00 mω Response time: ms Operating temperature: -20... +80 C (-... +76 F) High temperature version: +50 C max. (TQM/) (+02 F) Protection rating (EN 60529): IP 66 Shock resistance: 50 g (during ms) Vibration resistance: 5 g (50 to 2000 Hz) Cable type: PVC 2 x 0,75, PUR 2 x 0,75 VMQ 2 x 0,75 (TQM/) Cable length: 2, 5 or 0 m Electromagnetic compatibility according to: EN 6097-5-2 Materials: Body: plastic Cable: see table below Technical data - Reed switches - additional information see data sheet en..02 Symbol ~ + BN ~ BU BN BU Voltage (V a.c./v d.c.) Current maximum () Function Temperature ( C) LED Protection class Features Cable length (m) Cable type Weight (g) Model 0... 0 Normally open -20... +80 IP 66 2, 5 or 0 PVC 2 x 0,75 08 (2 m) QM/2/* 0... 0 Normally open -20... +80 IP 66 2 PUR 2 x 0,75 08 QM/2/2/PU 0... 0 2 Normally open -20... +50 IP 66 High temperature 2, 5 or 0 Silicon 2 x 0,75 02 (2 m) TQM//* + BN ~ ~ BK 0... 0 Normally open -20... +80 IP 66 Plug M2 x 5 QM/2/P *) Technical data - Solid state - additional information see data sheet en..025 Symbol pnp + BN BU BK Voltage (V d.c.) Current maximum (m) Function Temperature ( C) LED Protection class Features Cable length (m) Cable type Weight (g) Model 0... 0 200 PNP -20... +80 IP 66 2, 5 or 0 PVC x 0,5 02 (2 m) QM/2/* 0... 0 200 PNP -20... +80 IP 66 5 PUR x 0, QM/2/5/PU pnp + BN BU BK 0... 0 200 PNP -20... +80 IP 66 Plug M2 x 5 QM/2/P *) * Insert cable length *) Plug-in connector see page below; Color code: BK = black, BN = brown, BU = blue without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.2
PR/80000, PR/80000, R/80000, R/80000 Dimensions TQM/, QM/2, QM/2 QM/2/P, QM/2/P Dimensions in mm Projection/First angle X 5 27 X 5 27 2 M2 x 20 6 20 6 8 5 X 0 5,5 2 ø 5,8 ø,2 BN BK 5,8 LED (yellow) 2 Plug M2 x Color code BK = black BN = brown BU = blue BU ccessories Plug-in connector cable with nut Outer cover Cable length (m) Weight (kg) Connector Connector PVC x 0, 5 0,2 M2 x M/P692/5 PUR x 0, 5 0,2 M2 x M/P59/5 QM//000/22 Switch mounting brackets for Round barrel Switches: TQM/, QM/2, QM/2 Cy. ø B Weight (kg) Model 2 5 2 0,026 QM//02/22 0,5 6 0,026 QM//02/22 50,5 50,5 0,026 QM//02/22 6 56,5 0,026 QM//02/22 80 2 62,5 0,028 QM//080/22 00,5 70,5 0,028 QM//080/22 L B 2 Bracket 2 Switch en..220. without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
PR/80000, PR/80000, R/80000, R/80000 > Pneumatic proximity sensor > Port size: ø mm > Optical pressure indicator signals position > Non-contact sensing with pneumatic output > Intrinsically safe no problem in explosion areas 2 2 0 Technical features Medium: Compressed air, filtered and non-lubricated Operation: Pneumatic proximity switch for non-contact sensing via a magnetic field Operating pressure: 2... 6 bar (29... 87 psi) Connections: Pipes for mm l/d tubing Vibration resistance: 0... 50 Hz (to IEC 68 T. 2-27) Shock resistance: 500 m/s 2 over a period of 5 ms (to IEC 68 T. 2-27) Flow rate: 0 l/min Orifice size: 2 mm Repeatability: ± 0,2 mm Can be used with cylinder: ø 2... 00 mm Operating temperature: -5... +60 C (+5... +0 F) Humidity and water content: ir supply must be dry. Corresponding of the application and working conditions the air must be dry enough to avoid condensate. The pressure dewpoint must be minimum 5 C under the application and working conditions. Materials Body: Plastic Pipe connectors: Brass Holding strap: CU ZU 7 (brass) Pneumatic proximity sensor - additional information see data sheet en..06 Symbol Operating pressure Flow rate Orifice size Optical indicator Connections Model 2 2... 6 bar 0 l/min 2 mm Pipes for mm l/d tubing QM/0 Dimensions,5 M 6,5 9,5 2 7,5 8 7 8 2 2 5 5 9 7,5 8 Compressed air port 2 Output port 2 Exhaust port Optical indicator without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.25
E H J PR/80000, PR/80000, R/80000, R/80000 QM/0/00/22 Bracket with holding strap Pneumatic switch: QM/0 Dimensions in mm Projection/First angle ø (Round barrel) (kg) 2 22 0,020 0 2 0,020 50 22 0,020 6 0,020 80 2 0,020 00,5 0,020 Valve mounting kit for Profile barrel K C F D G B ø B C D E F G H J K SW (kg) Model 50/6 60 7 7,5 6 8,5 5,5 2 M 0,08 PQ/802050/22/5 80/00 90 7 7,5 76 8,5 6,5 70 2 M 0, PQ/802080/22/5 en..220.26 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH
H PR/80000, PR/80000, R/80000, R/80000 Valve mounting kit for Round barrel Dimensions in mm Projection/First angle B2 B L L2 G 0 SW SW 2 ø B B2 H L L2 G kg Model 6 6,5 77,5 50 7,5 M 0, Q/806/22/55/ 6 6,5 77,5 50 7,5 M5 0, Q/806/22/55/5 6 6,5 77,5 50 7,5 M6 0, Q/806/22/55/6 80 78 9 59,5 7,5 M 0, Q/8080/22/55/ 80 78 9 59,5 7,5 M5 0, Q/8080/22/55/5 80 78 9 59,5 7,5 M6 0, Q/8080/22/55/6 00 97 68 7,5 M 0,9 Q/800/22/55/ 00 97 68 7,5 M5 0,9 Q/800/22/55/5 00 97 68 7,5 M6 0,9 Q/800/22/55/6 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH en..220.27
PR/80000, PR/80000, R/80000, R/80000 Recommended Valves Recommended Valve Range Cylinder Tubing Valve Inline Valve V60 ISO Valve ø Port size ø Flow l/min Valve port size 2 G/8 6/ 250 /8" V60 0 G/ 6/ 250 /8" V60 50 G/ 6/ 250 /8" V60 6 G/8 8/6 750 /8" V60 80 G/8 0/7 250 /" V6 ISO Star UM/22000 00 G/2 0/7 250 /" V6 ISO Star UM/22000 Customer Solution Cylinder valve unit For additional information please contact the technical service Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under»technical features/data«. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems or other applications not within published specifications, consult IMI Precision Engineering, Norgren GmbH. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products. en..220.28 without notice, the specifications given in this document. (207-920b) 205 Norgren GmbH