By/Date: Page 1 of 5 Criteria Notes esults ating SCOPE: This protocol is applicable for testing of keychain / battery operated keychain / keychain with light. SUPPLEMENTY POTOCOL Note: dditional cost, sample size & TT may be required if testing to 1 or more supplemental protocols is necessary. Please refer to the below referenced supplemental protocol(s) for additional information. California Proposition 65 DILL-N-PTCL- 06572-US 6 The sample should be reviewed against the requirements of California Proposition 65. LBELING US Packaging F.P. and L. ct ll Packaging shall be labelled with the following, labeling (16 CF 500) O NIST Uniform Laws and egulations Handbook 130 Product Identification Net quantity of contents shall be expressed in terms of weight or mass, measure, numerical count, or combination so as to give accurate information to facilitate consumer comparison (U.S. and metric units) Manufacturer, packer, or distributor s name & address (City, State & Zip Verify presence of labeling and Labeling review: product or claims Battery labeling - or instruction Battery product compartment design guidance NSI C18.1M Pt. 2-2011 nnex / ll ll ll ll Code) Must comply with all claims [Permanent on product] Size of battery and direction of polarity, No. of Batteries equired, Batteries included or not. For products with more than one battery, must include: Do not mix old and new batteries. Do not mix alkaline, standard (carbon - zinc), or rechargeable (nickel cadmium) batteries [Not pplicable to Watches with single button cell] Products with replaceable batteries shall be provided with marking on/near the battery compartment to identify polarity alignment. Products with replaceable batteries, the battery compartment, or instruction with the product shall indicate the type of battery to use and how to insert correctly. Compartments shall be designed so batteries are: - secured in place and not fall out too easily - positioned to minimize risk of user harm (falling, heat, leaks), especially for devices worn on body. - not making electrical contact if inserted backwards - where practicable. - not a pressure hazard in case of cell venting - free from metal that contacts or abrades the case / jacket and may lead to short circuits.
By/Date: Page 2 of 5 Battery product instructions Battery labeling - NLYTICL Total lead in surface coating Total mercury in battery Total mercury in button cell battery NSI C18.1M Pt. 2-2011 Sec. 9 (Mod) CPSC-CH-E1003-09.1 / CPSD-N- 00001- Mercury- Containing and echargeable Battery Management ct U.S. Public Law 104-142 Title II / CPSD-N-00078- US Various state laws / CPSD-N- 00078- Criteria Notes esults ating Notes to lab: For the above mentioned requirement, "not making electrical contact if inserted backwards - where practicable.", it shall be fail directly, if it is made physical contact once the battery/batteries was/were inserted backwards (Does not apply to button cells operated items). ll [Not pplicable to Watches with single button cell] Products with replaceable batteries shall instruct user to replace batteries ensuring proper polarity, with the correct battery type, and as a simultaneous set. Modification: The above required instructions are modified to be also acceptable if provided on battery compartments. ll Packaging of products using replaceable batteries shall indicate the type / designation and number of batteries required and whether they are included or not. eport claim. 1 ll accessible surface coatings in the as received state on items outside of the scope of 16 CF 1303 shall not contain lead or lead components in which the lead content is in excess of 0.009% (90ppm) of the weight of the total content. eport actual results or include data table within report. Component testing is allowed. Compositing up to 3 like colors is allowed. The composite result will be evaluated against the adjusted limit (regulatory limit divided by the number of composites). Client requirement - Batteries shall comply with one of the following requirements: (i) lkaline-manganese button cell shall contain less than 25 mg Hg / cell. (ii) lkaline-manganese battery and Zinc carbon battery shall contain no intentionally added mercury (BV reporting limit is 4 mg/kg). (iii) No Mercuric-oxide button cell or battery is allowed. ctual testing would be conducted on button cell batteries. It is the vendor s responsibility for the conformity to this requirement for other batteries. - Shall not be detectable (less than 5 ppm) in button cell batteries or any product/novelty items containing such batteries. Note: -For Maine, test applicable to button cell batteries included zinc-air button cell battery, alkaline manganese button cell battery, silver oxide button cell battery stamped with designation S357, S362, S371, S377 or S395, and other
By/Date: Page 3 of 5 Toxicological risk assessment-doc 16 CF 1500.3(b)(5) and 1500.3(b)(7)-(9) / CPSD-GB-00001- PHYSICL CHCTEISTICS Weight CPSD-GB-01056- Dimensions - CPSD-GB-01056- length x width x height Material type WOKMNSHIP Hazardous sharp point and sharp edge Defects and workmanship PEFOMNCE Drop test Cycle test Effects of extreme temperature change 16 CF 1500.48 & 49 (Mod) CPSD-HL-01059- CPSD-GB-01058- CPSD-HL-01012- Criteria Notes esults ating silver oxide button cell. (effective date for silver oxide button cell : Jan 1, 2015) -Test is not applicable on product that solely includes a fluorescent light bulb in Ohio states. - Product shall be evaluated for the potential to be a toxic, a skin irritant, eye irritant, corrosive or strong sensitizer. If toxicological hazard(s) is/are present, the product shall be labeled appropriately (refer to labeling section for details). Toxicity isk ssessment shall be conducted for the following components: - The following high risk materials: liquids, pastes, putties, gels and powders regardless of claim - Other materials bearing a "NON-TOXIC" claim on samples and/or its In lieu of testing, test report can be submitted if dated within five years. 1 eport overall weight; shall meet label claims. 1 eport overall dimensions; shall meet label claims. 1 Shall be as claimed. 1 Shall have no sharp points / edges, other than those required for function. Modification: Expanded scope to other products. 1 Shall have no discernible surface degradation, including crazing, shivering, denting, bubbles, cracks, stains, deformations, chips, fractures, heavy lines, waves, shear marks, scratches, scuff marks, indentations, or blisters. Shall have no components missing, malformed, and/or fractured. 1 No breakage after 3 drops from a height of 3 ft 1 100 activation of switch & buttons 1 24 hours at 32 F and 120 F - No failure or visual change Modification: Exposure time changed form 4 hours to 24 hours; testing temperature changed from 0 F and 120 F to 32 F and 120 F
By/Date: Page 4 of 5 STM B117-16 (mod) / CPSD-HL- 01010- esistance to corrosion ttachment strength ttachment strength COLOFSTNESS Colorfastness to rotary crocking STM D1683-17e1 (Mod) STM D1683-17e1 (Mod) 1 [pplicable to samples or sample components constructed of metal or samples with metallic coatings that can be exposed to the environment] Shall withstand 24 hours in 1% salt spray (fog) with no noticeable oxidation / corrosion / visual changes. Modification: 1% salt spray (fog). 1 [Keying to product] 20 lb minimum Modification: Expanded scope to other product and clamping device 1 [Keying to plastic connecting cord] 20 lb minimum Modification: Expanded scope to other product and clamping device TCC 116-13 1 Dry: Grade 4.0 Minimum Wet: Grade 3.0 Minimum Criteria Notes esults ating No. Of equired for Complete Testing No. Of (Fully Packed) Cartons For Transit Testing: 4 pcs, 1 set Minimum of 6 per style metal, 1 4 leather / fabric 1 (Only Upon Dillard s equest) Client pproval: Creation Date: Last evision Date: Lucy Feng 02/Feb/2018 16/May/2000 23/Jan/2018 No. Of Working Days For Complete Testing: 5 Pricing eview Date Technical eview Date: 13/Feb/2015 Key M dditional Charge For This Test Mandatory egulatory
By/Date: Page 5 of 5 esult Key C M NM N NT Claimed ecorded Meets Does Not Meet Not pplicable Not Tested ating Key PSS FIL N Pass Fail Not equested