Tie rod cylinders, Series PDF Free Download

Electric Drives and Controls Hydralics Linear Motion and Assembly Technologies Pneumatics Service Tie rod cylinders, Series 523 Technical data

Tie rod cylinders, Series 523 Grey series, 32 25 mm ( /4"-5") dia., magnetic piston, adjustable cushioning Technical Data Standard ISO 5552 (ISO 643, VDMA 24562) CNOMO / NFE 49-003- Working pressure, max. 0 bar (45 psi) Ambient temperature range -20 C to +70 C (-4 F to +58 F) Medium Compressed air ISO 8573-:200, class 6-4-3 or lower* Materials Piston rod Stainless steel (BS 303 S 3) Piston rod bushing Steel with a PVDF + PTFE bearing surface Cylinder body Anodized aluminum End covers Aluminum Tie-rods Surface treated steel Nut Surface treated steel Wiper Polyurethane Piston 32 63 mm ( /4"-2 /2") dia. polyamide, 80 25 mm (3"-5") dia. Aluminum Cushioning screws Stainless steel (BS 303 S 3) Seals Nitrile rubber/polyurethane For use between 5 C and 40 C (+5 F and 40 F) continuously, seals for low temperature are recommended. Please contact your nearest Bosch Rexroth office. Application area This cylinder series is suitable for use when large masses are to be moved or where the stroke frequency is high: The packaging industry where high frequency and long service life is required, etc. Approved by automotive manufacturers. * Particle size 5 µm, dew point 3 C, oil content mg/m³ Technical information Piston Ø (inch) 32 ( /4") 40 ( /2") 50 (2") 63 (2 /2") 80 (3") 00 (4") 25 (5") Theoretical piston force push stroke [N] 483 754 78 870 306 472 7363 at 6 bar (87 psi) (lbf) (09) (70) (265) (420) (678) (059) (655) pull stroke [N] 45 633 990 682 272 448 688 (lbf) (93) (42) (223) (378) (62) (993) (547) Cushioning length,5 5,0 7,0 6,5 9,5 9,5 22,0 (inch) (0.5) (0.6) (0.7) (0.6) (0.8) (0.8) (0.9) Cushioning energy¹) [Nm] 4,8 9,0 5,0 27,0 54,0 88,0 40,0 (in.lbs) (53.0) (80.0) (33.0) (239.0) (478.0) (779.0) (239,0) Weight 0 mm stroke [kg] 0,45 0,76,0,7 2,50 3,70 6,90 (lbs) (0.99) (.68) (2.43) (2.58) (5.5) (8.6) (5.2) add. per 00 mm [kg] 0,20 0,29 0,45 0,49 0,78,00,3 add. per 4" (lbs) (0.44) (0.64) (0.99) (.08) (.72) (2.2) (2.89) ¹) Cushioning diagram, see chapter 5.

Tie rod cylinders, Series 523 Grey series, 32 25 mm ( /4"-5") dia., magnetic piston, adjustable cushioning Part no. Piston dia. (inch) 32 ( /4") 40 ( /2") 50 (2") 63 (2 /2") 80 (3") Piston rod thread M 0 x,25 M 2 x,25 M 6 x,5 M 6 x,5 M 20 x,5 Threaded port G/8 G /4 G /4 G 3/8 G 3/8 Stroke²) 25 5230030050 523030050 5232030050 5233030050 5234030050 50 523003000 52303000 523203000 523303000 523403000 80 523003060 52303060 523203060 523303060 523403060 00 5230030200 523030200 5232030200 5233030200 5234030200 25 5230030250 523030250 5232030250 5233030250 5234030250 60 5230030320 523030320 5232030320 5233030320 5234030320 200 5230030400 523030400 5232030400 5233030400 5234030400 250 5230030500 523030500 5232030500 5233030500 5234030500 320 5230030640 523030640 5232030640 5233030640 5234030640 400 5230030800 523030800 5232030800 5233030800 5234030800 500 523003000 52303000 523203000 523303000 523403000 Rec. max. stroke²) 600 900 200 2500 2800 Piston dia. (inch) 00 (4") 25 (5") Piston rod thread M 20 x,5 M 27 x 2 Threaded port G /2 G /2 Stroke²) 25 5235030050 5236030050 50 523503000 523603000 80 523503060 523603060 00 5235030200 5236030200 25 5235030250 5236030250 60 5235030320 5236030320 200 5235030400 5236030400 250 5235030500 5236030500 320 5235030640 5236030640 400 5235030800 5236030800 500 523503000 523603000 Rec. max. stroke²) 2800 2750 Optional strokes: See Ordering system for cylinders in optional design. ²) Longer strokes on request. ³) Intermediate strokes in steps of 5 mm may be delivered. See Ordering system for cylinders in optional design. Codification par configurateur internet. 2

Tie rod cylinders, Series 523 Grey series, 32 25 mm ( /4"-5") dia., magnetic piston, adjustable cushioning Accessories (to be ordered separately) Symbol Type Piston dia. (inch) 32 40 50 63 Front or rear flange (MF/MF2) 523000602 52300602 523200602 523300602 Angle brackets (MS) 5230000502 523000502 5232000502 5233000502 Central male trunnion (MT4) 5230006902 523006902 5232006902 5233006902 Front or rear pivoted mounting (MT5/MT6) 523086902 52386902 523286902 523386902 Rear end cover clevis (MP0) 5230003432 523003432 5232003432 5233003432 Rear eye with PTFE bushing (MP4) 82700283 82700284 82700285 827020086 Rear clevis (MP2) 82700289 82700290 8270029 82700500 Rear eye with rubber bushing (M32) 3683203000 3683204000 3683205000 3683206000 Rear eye with ball joint (M36) 3683603000 3683604000 3683605000 3683606000 Piston dia. (inch) 80 00 25 Front or rear flange (MF/MF2) 523400602 523500602 523600602 Angle brackets (MS) 5234000502 5235000502 5236000502 Central male trunnion (MT4) 5234006902 5235006902 5236006902 Front or rear pivoted mounting (MT5/ MT6) 523486902 523586902 523686902 Rear end cover clevis (MP0) 5234003432 5235003432 5236003432 Rear eye with PTFE bushing (MP4) 82700287 82700288 827004866 Rear clevis (MP2) 82700293 82700294 827004862 Rear eye with rubber bushing (M32) 3683208000 368320000 Rear eye with ball joint (M36) 5234003452 5235003452 5236003452 Piston dia. (inch) 32 25 Sensor with 2,5 m cable, Reed 27503230 27503230 Sensor with 2,5 m cable, PNP 275030 275030 Sensor mounting for the Grey Series (profile version 03) Ø 32 63 27525000 Ø 80 25 275235000 Piston dia. (inch) 32 40 50 63 Rod clevis (P) 82222024 82222025 82222005 82222005 Rod clevis in stainless steel (P2) 3590502000 3590504000 3590505000 3590505000 Mounting plate (P3) 523086002 52386002 523286002 523286002 Ball eye rod end (P4) 82224003 82224004 82224005 82224005 Flexible coupling (P5) 826409002 826409003 826409004 826409004 Piston dia. (inch) 80 00 25 Rod clevis (P) 82222004 82222004 82700493 Rod clevis in stainless steel (P2) 3590508000 3590508000 - Mounting plate (P3) 523486002 523486002 523686002 Ball eye rod end (P4) 82224006 82224006 8222403 Flexible coupling (P5) 826409005 826409005 826409006 Seal kit Symbol Piston dia. (inch) 32 ( /4") 40 ( /2") 50 (2") 63 (2 /2") 80 (3") 00 (4") 25 (5") Part no. 0490394303 0490394400 0490394508 0490394605 0490394702 275534000 275634000 3

Tie rod cylinders, Series 523 Grey series, 32 25 mm ( /4"-5") dia., magnetic piston, adjustable cushioning Tolerance Ø 32 50 mm = +2/-0, Ø 63 25 mm = +2,5/-0 S* = Stroke Piston dia. B e d4 d5 E G L2 L8 L9 L2 P EE KK MM g 8 32 30 36 5,5 49,5 28 5 94 ±0,4 5 6,0 4,0 G /8 M 0x,25 2 40 35 44 5,5 54,5 33 9 05 ±0,7 5 6,5 5,0 G /4 M2x,25 6 50 40 54 7,5 67,0 3 24 06 ±0,7 6 8,0 7,5 G /4 M6x,5 20 63 45 68 7,5 78,0 38 24 2 ±0,8 6 8,0,0 G 3/8 M6x,5 20 80 45 85 9,0 00,0 38 30 28 ±0,8 0,0,0 G 3/8 M 20x,5 25 00 55 07 9,0 20,0 42 35 38 ±,0 0,0 7,0 G /2 M 20x,5 25 25 60 3 0,8 45,0 54 45 60 ±,0 3,0 27,5 G /2 M 27x2 32 Piston dia. AM BG min. KV KW PL RT SW TG VA VD WH ZJ 32 22 6 7 5,0 6 M6 0 32,5 ±0,5 3,5 4 26 20 40 24 6 8 6,0 7 M6 3 38,0 ±0,5 3,5 4 30 35 50 32 6 24 8,0 6 M8 7 46,5 ±0,6 4,0 4 37 43 63 32 6 24 8,0 9 M8 7 56,5 ±0,7 4,0 4 37 58 80 40 6 30 0,0 9 M 0 22 72,0 ±0,7 4,0 4 46 74 00 40 6 30 0,0 9 M 0 22 89,0 ±0,7 4,0 4 5 89 25 54 20 4 3,5 20 M2 27 0,0 ±, 6,0 6 65 225 4

Tie rod cylinders, Series 523 Grey series, 60 320 mm dia., adjustable cushioning,with or without magnetic piston Technical Data Standard ISO 5552 (ISO 643, VDMA 24562) CNOMO / NFE 49-003- Working pressure, max 0 bar (45 psi) Ambient temperature range -5 C to +70 C (+5 F to +58 F) Medium Compressed air ISO 8573-:200, class 6-4-3 or lower* Materials Piston rod Stainless steel (BS 303 S 3) Cylinder body Anodized aluminum End covers Aluminum Seals Nitrile rubber/polyurethane Application area Suitable for all mechanical systems. Approved by automotive manufacturers. * Particle size 5 µm, dew point 3 C, oil content mg/m³ Technical information Piston Ø 60 200 250 320 Theoretical piston force push stroke [N] 834 8 49 28 892 47 338 at 6 bar (87 psi) (lbf) (2660) (457) (6495) (0640) pull stroke [N] 095 7 752 27 737 45 503 (lbf) (2494) (399) (6236) (0230) Cushioning length 50 50 64 46 Cushioning energy¹) [Nm] 325 550 000 90 (in.lbs) (2876) (4868) (885) (0 532) Weight 0 mm stroke [kg],6 4,5 30,0 6,4 (lbs) (25.6) (32.0) (66.) (35.4) add. per 00 mm [kg] 2,68 3,2 3,8,8 add. per 4" (lbs) (5.9) (7.) (8.4) (26.0) ¹) Cushioning diagram, see chapter 5. Part no. with magnetic piston Piston Ø 60 200 250 320 Piston rod thread M 36 x 2 M 36 x 2 M 42 x 2 M 48 x 2 Threaded port G 3/4 G 3/4 G G Stroke 4 ) 25 5237030050 5238030050 5239030050 5239035050 50 523703000 523803000 523903000 523903500 80 523703060 523803060 523903060 523903560 00 5237030200 5238030200 5239030200 5239035200 25 5237030250 5238030250 5239030250 5239035250 60 5237030320 5238030320 5239030320 5239035320 200 5237030400 5238030400 5239030400 5239035400 250 5237030500 5238030500 5239030500 5239035500 320 5237030640 5238030640 5239030640 5239035640 400 5237030800 5238030800 5239030800 5239035800 500 523703000 523803000 523903000 5239036000 Optional²) 523 703 xxx 0 2 ) 523 803 xxx 0 2 ) 523 903 xxx 0 2 ) 523 903 xxx 0 5 ) Rec. max. stroke³) 2700 2700 995 995 ²) Stroke is given in mm/5, for example 30 mm = 006. ³) Longer strokes on request. 4 ) Intermediate strokes in steps of 5 mm may be delivered. 5 ) Stroke is given in mm/5 + 500, for example 30 mm = 506.

Tie rod cylinders, Series 523 Grey series, 60 320 mm dia., adjustable cushioning,with or without magnetic piston Part no. without magnetic piston Piston Ø 60 200 250 320 Piston rod thread M 36 x 2 M 36 x 2 M 42 x 2 M 48 x 2 Threaded port G 3/4 G 3/4 G G Stroke 4 ) 25 5237000050 5238000050 5239000050 5239005050 50 523700000 523800000 523900000 523900500 80 523700060 523800060 523900060 523900560 00 5237000200 5238000200 5239000200 5239005200 25 5237000250 5238000250 5239000250 5239005250 60 5237000320 5238000320 5239000320 5239005320 200 5237000400 5238000400 5239000400 5239005400 250 5237000500 5238000500 5239000500 5239005500 320 5237000640 5238000640 5239000640 5239005640 400 5237000800 5238000800 5239000800 5239005800 500 523700000 523800000 523900000 5239006000 Optional 2 ) 523 700 xxx 0 2 ) 523 800 xxx 0 2 ) 523 900 xxx 0 2 ) 523 900 xxx 0 5 ) Rec. Max. stroke³) 2700 2700 995 995 ²) Stroke is given in mm/5, for example 30 mm = 006. ³) Longer strokes on request. 4 ) Intermediate strokes in steps of 5 mm may be delivered. 5 ) Stroke is given in mm/5 + 500, for example 30 mm = 506. Accessories (to be ordered separately) Symbol Type Piston dia. 60 200 250 320 Front or rear flange (MF/MF2) 5230866002 5230966002 523900602 52390602 Angle brackets (MS) 5237000502 5238000502 5239000502 523 90 050 2 Rear clevis (MP2) 827004863 827004864 827004865 523 98 340 2 Proximity reed switch with LED 89404062 89404062 89404062 89404062 Connector 894004702 894004702 894004702 894004702 Clamp for sensor 3220673522 3220673522 3220893502 3220893502 Further sensors...¹) Rod clevis (P) 8270047 8270047 82700472 82700472 ¹)...see at the product overview. Ball eye rod end (P4) 82424008 82424008 82224009 8958208842 2

Tie rod cylinders, Series 523 Grey series, 60 320 mm dia., adjustable cushioning,with or without magnetic piston S* = Stroke Piston dia. AL AM B BG d 4 d 5 d 9 E EE e ISO 228 G KK KV KW L2 L8 60 72 65 24 68 4,7 63,0 80 G 3/4 58,0 M36x2 55 8 52,5 80 200 72 75 24 20 4,7 72,0 220 G 3/4 56,5 M36x2 55 8 56,0 80 250 84 90 25 262 20,0 82,5 280 G 59,5 M42x2 65 2 76,0 200 320 96 0 28 340 24,0 03,0 350 G 6,5 M48x2 75 24 87,0 220 Piston dia. AL L2 MM PL RT SW SW3 TG VA VD WH ZJ 60 6,0 40 35,0 M6 32 27 40 6 6 80 260 200 6,0 40 30,0 M6 32 27 75 6 6 95 275 250 9,5 50 33,0 M20 46 4 220 0 0 05 305 320 23,5 63 34,5 M24 55 50 270 0 2 20 340 3

Tie rod cylinders, Series 523 Grey series, 60 250 mm dia., Technical Data Type Piston cylinder, tie-rod version Standard VDMA 24562; DIN ISO 643; NFE 49-003 Working pressure p. max 0 bar (45 psi) Ambient temperature range -5 C to +70 C (+5 F to +58 F) Medium Compressed air ISO 8573-:200, class 6-4-3 or lower* Material Piston rod X5CrNi8.9 Cylinder body AlMgSiF28 Covers Al-diecasting Seals NBR (Nitrile Butadiene Rubber) Application area Suitable for all mechanical systems. Approved by automotive manufactures, ask for special data sheet. * Particle size 5 µm, dew point 3 C, oil content mg/m³ Technical information Piston Ø 60 200 250 Theoretical piston force push stroke [N] 834 8 49 28 892 at 6 bar (87 psi) (lbf) (2660) (457) (6495) pull stroke [N] 095 7 752 27 737 (lbf) (2494) (399) (6236) Cushioning length 50 50 64 Cushioning energy¹) [Nm] 325 550 000 (in.lbs) (2876) (4868) (885) Weight 0 mm stroke [kg],6 4,5 30,0 (lbs) (25.6) (32.0) (66.) add. per 00 mm [kg] 2,68 3,2 3,8 add. per 4" (lbf) (5.9) (7.) (8.4) ¹) Cushioning diagram see section 5. Part no. with magnetic piston Piston Ø 60 200 250 Piston rod thread (KK) M 36 x 2 M 36 x 2 M 42 x 2 Threaded ports (EE)²) G 3/4 G 3/4 G Stroke 25 5237630050 5238630050 5239630050 50 523763000 523863000 523963000 80 523763060 523863060 523963060 00 5237630200 5238630200 5239630200 25 5237630250 5238630250 5239630250 60 5237630320 5238630320 5239630320 200 5237630400 5238630400 5239630400 250 5237630500 5238630500 5239630500 320 5237630640 5238630630 5239630640 400 5237630800 5238630800 5239630800 500 523763000 523863000 523963000 Rec. max. stroke¹) 2700 2700 995 ¹) Longer strokes on request. ²) ISO 228/.

Tie rod cylinders, Series 523 Grey series, 60 250 mm dia., Part no. without magnetic piston Piston Ø 60 200 250 Piston rod thread (KK) M 36 x 2 M 36 x 2 M 42 x 2 Threaded ports (EE)²) G 3/4 G 3/4 G Stroke 25 5237600050 5238600050 5239600050 50 523760000 523860000 523960000 80 523760060 523860060 523960060 00 5237600200 5238600200 5239600200 25 5237600250 5238600250 5239600250 60 5237600320 5238600320 5239600320 200 5237600400 5238600400 5239600400 250 5237600500 5238600500 5239600500 320 5237600640 5238600640 5239600640 400 5237600800 5238600800 5239600800 500 523760000 523860000 523960000 Rec. max. stroke¹) 2700 2700 995 ¹) Recommended max. stroke (longer strokes on request). ²) ISO 228/. Accessories (to be ordered separately) Symbol Type Piston dia. 60 200 250 Front or rear flange (MF/MF2) 5230866002 5230966002 523900602 Angle brackets (MS) 5237000502 5238000502 5239000502 Rear clevis (MP2) 827004863 827004864 827004865 Proximity reed switch with LED 89404062 89404062 89404062 Connector 894004702 894004702 894004702 Clamp for sensor 3220673522 3220673522 3220893502 Further sensors...¹) Rod clevis (P) 8270047 8270047 82700472 ¹)...see at the product overview. Ball eye rod end (P4) 82424008 82424008 82424009 2

Tie rod cylinders, Series 523 Grey series, 60 250 mm dia., S* = Stroke Piston dia. AL AM B BG d4 E EE e ISO 228 G KK KV KW L8 MM PL RT 60 72 65 24 68 80 G 3/4 58,0 M36x2 55 8 80 40 35 M6 200 72 75 24 20 220 G 3/4 56,5 M36x2 55 8 80 40 30 M6 250 84 90 25 262 280 G 59,5 M42x2 65 2 200 50 33 M 20 Piston dia. AL SW SW TD e 9 TG TL TM TT UW WH WH XV min. 60 32 27 32 40 32 200 50 90 52,5 80 63,0 77,0 + S* 260 200 32 27 32 75 32 250 50 240 56,0 95 76,5 93,5 + S* 275 250 46 4 40 220 40 320 60 30 76,0 05 94,5 25,5 + S* 305 XV max. ZJ 3

Tie rod cylinders, Series 523 Grey series, 60 320 mm dia., adjustable cushioning, high temperature Technical Data Type Piston cylinder, tie-rod version Standard VDMA 24562; DIN ISO 643; NFE 49-003 Operating pressure p. max 0 bar (45 psi) Ambient temperature range -5 C to +50 C (+5 F to +302 F) Permissible medium Compressed air ISO 8573-:200, class 6-4-3 or lower* Material Piston rod BS 303 S3 (V2A), roller burnished Cylinder body Anodized aluminum Cover and base GD-Al Seals Viton Application area For all applications at extremely high temperatures. * Particle size 5 µm, dew point 3 C, oil content mg/m³ Technical information Piston Ø 60 200 250 320 Theoretical piston force push stroke [N] 834 8 49 28 892 47 338 at 6 bar (87 psi) (lbf) (2660) (457) (6495) (0 640) pull stroke [N] 095 7 752 27 737 45 503 (lbf) (2494) (399) (6236) (0 230) Cushioning length 50 50 64 46 Cushioning energy¹) [Nm] 325 550 000 90 (in.lbs) (2876) (4868) (885) (0 532) Weight 0 mm stroke [kg],6 4,5 30,0 6,4 (lbs) (25.6) (32.0) (66.) (35.4) add. per 00 mm [kg] 2,68 3,2 3,8,8 add. per 4" (lbs) (5.9) (7.) (8.4) (26.0) ¹) Cushioning diagram, see chapter 5. Part no. without magnetic piston Piston Ø 60 200 250 320 Piston rod thread (KK) M 36 x 2 M 36 x 2 M 42 x 2 M48 x 2 Threaded ports (EE) 2 ) G 3/4 G 3/4 G G Stroke 25 5237040050 5238040050 5239040050 5239045050 50 523704000 523804000 523904000 523904500 80 523704060 523804060 523904060 523904560 00 5237040200 5238040200 5239040200 5239045200 25 5237040250 5238040250 5239040250 5239045250 60 5237040320 5238040320 5239040320 5239045320 200 5237040400 5238040400 5239040400 5239045400 250 5237040500 5238040500 5239040500 5239045500 320 5237040640 5238040640 5239040640 5239045640 400 5237040800 5238040800 5239040800 5239045800 500 523704000 523804000 523904000 5239046000 Max. stroke 2700 2700 995 995 ²) ISO 228. Accessories (to be ordered separately) Symbol Type Piston dia. 60 200 250 320 Front or rear flange (MF/MF2) 5230866002 5230966002 523900602 52390602 Angle brackets (MS) 5237000502 5238000502 5239000502 523900504 Rear clevis (MP2) 827004863 827004864 827004865 523983402 Rod clevis (P) 8270047 8270047 82700472 82700472 Ball eye rod end (P4) 82224008 82224008 82224009 8958208842

Tie rod cylinders, Series 523 Grey series, 60 320 mm dia., adjustable cushioning, high temperature S* = Stroke Piston Ø AM B BG d 4 d 5 d 9 E EE e ISO 228 G KK KV KW L2 L8 60 72 65 24 68 4,7 63 80 G 3/4 58 M36x2 55 8 52,5 80 200 72 75 24 20 4,7 72 220 G 3/4 56,5 M36x2 55 8 56 80 250 84 90 25 262 20 82,5 280 G 59,5 M42x2 65 2 76 200 320 96 0 28 340 24 03 350 G 6,5 M48x2 75 24 87 220 Piston Ø L2 MM PL RT SW SW3 TG VA VD WH ZJ 60 6 40 35 M6 32 27 40 6 6 80 260 200 6 40 30 M6 32 27 75 6 6 95 275 250 9,5 50 33 M 20 46 4 220 0 0 05 305 320 23,5 63 34,5 M 24 55 50 270 0 2 20 340 2

Tie rod cylinders, Series 523 Ordering system for cylinders in optional design: How to order a cylinder in optional design step by step STEPS: STEP : Cylinder series Code 523 STEP 2: Piston diameter Code Diameter Code Diameter 0 32 4 80 40 5 00 2 50 6 25 3 63 Code example: Diameter 40 mm = STEP 3: Cylinder profile 03 = grey 08 = yellow 06 = red 07 = green Code example: Green profile = 07 STEP 4: Stroke Code Stroke ¹) Code Stroke ¹) 005 25 040 200 00 50 050 250 06 80 064 320 020 00 080 400 025 25 00 500 032 60 Optional Stroke in mm ¹) Dia. 32, max. stroke = 500 mm. Dia. 40 63, max. stroke = 600 mm. Dia. 80 25, max. stroke = 700 mm. Code example: Optional stroke 450 mm

Tie rod cylinders, Series 523 Ordering system for cylinders in optional design: STEP 5: Options Code Options 0 Without options 8 With options (optional stroke, mountings, sensors...) Code example: With options = 8 STEP 6: Mountings (for more information see accessories) Code Mounting / Profile Grey - 03 Red - 06 Green - 07 Yellow - 08 WITH sensors Yellow - 08 WITH sensors M00 Without mounting MF Front flange MF2 Rear flange MS Angled brackets ²) MT4 Central male trunnon¹) MT5 Front pivoted mounting MT6 Rear pivoted mounting MP0 Rear end cover clevis MP4 Rear eye with PTFE bushing MP2 Rear clevis ²) M32 Rear eye with rubber bushing ²) M36 Rear eye with ball joint ²) = Possible combination; = Impossible combination. ¹) Central male trunnion: when ordering with MT4, indicate XV (for ex. XV = 45 mm). ²) Some combinations with STEP 8: Connection port position are not possible. See table below STEP 8.' Code example: Front flange = MF STEP 7: Connection port thread Code Connection port thread B ISO 228/ STEP 8: Connection port position for possible combinations with different types of mountings Code Port position M00 MF MF2 MS MT4 MT5 MT6 MP0 MP4 MP2 M32 M36 Front 2, rear 2 ²) ²) 2 Front 2, rear 3 ²) ²) 3 Front 2, rear 6 ²) ²) 4 Front 2, rear 9 ²) ²) ²) 2 Front 3, rear 2 ²) ²) 22 Front 3, rear 3 ²) ²) ²) 23 Front 3, rear 6 ²) ²) 24 Front 3, rear 9 ²) ²) ²) 3 Front 6, rear 2 ²) ²) 32 Front 6, rear 3 ²) ²) 33 Front 6, rear 6 ²) ²) 34 Front 6, rear 9 ²) - ²) ²) 4 Front 9, rear 2 ²) ²) 42 Front 9, rear 3 - ²) ²) 43 Front 9, rear 6 ²) ²) 44 Front 9, rear 9 ²) ²) ²) 55¹) Double conn. front and ²) ²) rear 2 and 6 66¹) Double conn. front and ²) ²) rear 3 and 9 = Possible combination; = Impossible combination ¹) Codes 55 and 66 are only valid for Yellow profile (08), Green profile (07) and Red (06). ²) These port positions are not possible with yellow profile (08) with sensors. For more information see alternative connection ports and port position. Code example: Front 2, rear 3 = 2 2

Tie rod cylinders, Series 523 Ordering system for cylinders in optional design: View from front. STEP 9: Piston rod material Code Material S BS 303 S 3 STEP 0: Type of piston rod Code Type ISO STEP : Piston rod extension Code W Y Code example: With piston rod extension = Y Note! Indicate the value of Y separately on the order (for example: Y = 20 mm) Extension Without With (given in mm) STEP 2: Premounted sensors Code Premounted sensors 0 Without Front 2 Rear 3 Front and rear Code example: Premounted sensors on front and rear = 3 STEP 3: Sensor type for possible combinations with different cylinder profiles Code Type Grey - 03 Red - 06 Green - 07 Yellow - 08 00 Without R Reed, 2,5 m cable, PVC R2 Reed, 0 m cable, PVC R3 Reed, cable in PU with contact I Inductive, 2,5 m cable in PVC I2 Inductive, 0 m cable in PVC I3 Inductive, cable in PU with contact M8 I4 Inductive, cable in PU with contact M8 (as per EN 50082-2) I5 Inductive, cable in PU with contact M2 I6 Inductive, cable in PU with contact M8 (NPN) = Possible combination; = Impossible combination. For more information see accessories. Code example: Sensor Reed, 2,5 m cable, PVC = R 3

Tie rod cylinders, Series 523 Ordering system for cylinders in optional design: STEP 4: Function Code Function D Double acting P Double acting with a position holder T Through piston rod S Double acting with non-rotating piston rod H Hygienic design (only available for the Yellow profile - 08) For more information see page for each function. Code example: Double acting = D STEP 5: Piston rod accessories Code WW L L5 L9 P P2 P3 P4 P5 For more information see Accessories. Code example: Flexible coupling = P5 Piston rod accessories Without Linear guiding, H, plain bearing Linear guiding, H, ball bearing Linear guiding, U, plain bearing Rod clevis Clevis with pin in stainless steel Mounting plate Ball eye rod end Flexible coupling STEP 6: Seals Code S V Code example: Standard seals = S Seals Standard High temperature (Viton) STEP 7: Sealing concept piston rod Code Sealing 0 Standard PEE-wiper (Piston rod adapter with PEE-wiper) 2 PTFE-wiper (Piston rod adapter with PTFE-wiper) 3 Metal wiper (Piston rod adapter with metal wiper) 4 PDF wiper (Resitant to hot water washing, +40 C to +0 C (+04 F to +230 F) For more information see sealing concept and Hygienic design. Code example: Piston rod adapter with PEE-wiper = Ordering example: Cylinder series 523, dia. 40 mm, green profile, stroke 450 mm, with front flange, connection port for front 2, rear 3, with extended piston rod 20 mm, with two sensors Reed 2,5 m cable, double acting, with flexible coupling on piston rod, and with piston rod adapter with PEE wiper: 523 / 07 / 0450 8 - MFB2SY3 / RD / P5S Y = 20 mm 4

Tie rod cylinders, Series 523 Position holder, 32 25 mm ( /4"-5") dia., all profiles Technical Data Type, position holder/cylinder Spring retarded Standard Mounting holes for position holder and cylinder comply with VDMA 24562 and CNOMO/ NFE 49-003 Working pressure, max. 0 bar (45 psi) Release pressure 4 bar min. (58 psi min.) Ambient temperature range -5 C to +70 C (+5 F to +58 F) Medium Compressed air ISO 8573-:200, class 6-4-3 or lower* For use between 5 C and 40 C (+5 F and 40 F) continuously, seals for low temperature are recommended. Please contact your nearest Bosch Rexroth office. Materials Housing Anodized aluminum Other details see main cylinders. Application area The position holder is used to secure the piston rod in any chosen position along the stroke. As a machine safeguard: Interlocks when air is lost or in an emergency stop. Note: Must not be used as a personnel safeguard! * Particle size 5 µm, dew point 3 C, oil content mg/m³ Technical information Piston Ø (inch) 32 ( /4") 40 ( /2") 50 (2") 63 (2 /2") 80 (3") 00 (4") 25 (5") Min. holding force at 0 bar (0 psi) [N] 760 200 900 3000 5000 8000 2000 for vented pos. Holder (lbf) (7) (270) (427) (674) (24) (798) (2698) Weight of the position holder [kg] 0,8,0,8 2,8 5,5 9,5 3,8 (lbs) (.8) (2.2) (4.0) (6.2) (2.) (20.9) (30.4) Part no. See Ordering system for cylinders in optional design. S* = stroke Piston Ø B e E2 L9 L20 AM BG EE2 PL2 RT TG ±0,2 VD WH ZJ 32 30 48 25 44 22 6 G /8 9 M6 32,5 9 5 245 40 35 53 25 44 24 6 G /8 9 M6 38,0 2 55 260 50 40 63 45 49 32 6 G /8 9 M8 46,5 28 82 288 63 45 75 65 52 32 6 G /8 0 M8 56,5 28 202 323 80 45 98 85 6,5 40 7 G /8 M 0 72,0 34 23 359 00 55 8 220 68 40 7 G /8 3 M 0 89,0 37 27 409 25 60 42 220 75 54 20 G /4 3 M2 0,0 45 285 445 For other dimension, see double acting cylinder. Accessories and mountings (to be ordered separately) Base plate for control valve and wiper to the rear of the position holder for use without a cylinder. Inductive sensor M2x (89404082) with a connecting distance of 2 mm can be mounted in prepared holes. The sensor is activated when the disconnection pressure is 0 bar, i.e. the position holder is activated.

Tie rod cylinders, Series 523 Sealing concept piston rod, magnetic piston, Technical Data for standard cylinder Standard ISO 5552 (ISO 643, VDMA 24562) CNOMO / NFE 49-003- Working pressure, max. 0 bar (45 psi) Ambient temperature range -5 C to +70 C (+5 F to +58 F) Medium Compressed air ISO 8573-:200, class 6-4-3 or lower* For use between 5 C and 40 C (+5 F and 40 F) continuously, seals for low temperature are recommended. Please contact your nearest Bosch Rexroth office. Dimensions, see standard cylinder Other details see main cylinders Application area This cylinder series is suitable for environments where great emphasis is placed on the wiper removing e.g. resin, gravel and dust. The bearing housings are easy to replace without the need to dismantle the cylinder or remove it from the application. * Particle size 5 µm, dew point 3 C, oil content mg/m³ Part no. See Ordering system for cylinders in optional design. Technical Data for adapter Material Piston rod bushing Steel, bearing layer composite PVDF + PTFE Wiper Metal Polyesterelastomer (PEE) Carbon-filled PTFE Seals Nitrile rubber Casing Anodized aluminum Ambient temperature range -5 C to +70 C (+5 F to +58 F) Application area In very difficult environments high demands are made on a wiper. Depending on the environment different types of wipers are suitable. To fulfil maximum flexibility and ease of maintenance we offer different adapters for this application. Note that the cylinder is still to the ISO/VDMA standards built-in dimensions. Piston Ø 32 40 50 63 80 00 25 Metal 0496400402 049640058 049640058 0496400607 0496400607 049630404 PEE 0496400704 049640080 0496400909 0496400909 04964008 04964008 049630307 PTFE 04964007 049640204 049640203 049640203 0496402200 0496402200 049630706

Tie rod cylinders, Series 523 High temperature (Viton) with sealing concept piston rod, adjustable cushioning. Profiles - Grey, Red, Green and Yellow Technical Data, cylinders for high operating temperatures Standard ISO 5552 (ISO 643, VDMA 24562) CNOMO / NFE 49-003- Working pressure, max. 0 bar (45 psi) Ambient temperature range +20 C to +20 C (+68 F to +248 F) Medium Compressed air ISO 8573-:200, class 6-4-3 or lower* Materials Seals FPM rubber (Viton) Wiper Carbon-filled PTFE Other materials see main cylinders. Dimensions, see standard cylinder. Application area This version is suitable in hot zones, for example handling of oven-doors. Magnetic sensing can not be used as the cylinder lacks magnets. But, is available on special order. Note: This version cannot be combined with mounting M32 "Rear eye with rubber bushing", double acting cylinder with position holder, double acting with non-rotating piston rod, sensors or linear control units. * Particle size 5 µm, dew point 3 C, oil content mg/m³ Part no. See Ordering system for cylinders in optional design. Technical Data, cylinders for high operating temperatures with sealing concept piston rod Materials Piston rod bushing Steel with a PVDF + PTFE bearing surface de piston en PVDF + PTFE Wiper Metal or carbon-filled PTFE Seals FPM rubber (Viton) Casing Anodized aluminum Ambient temperature range +20 C to +20 C (+68 F to +248 F) Application area In very difficult environments high demands are made on a wiper. Depending on the environment different types of wipers are suitable. To fulfil maximum flexibility and for ease of maintenance we offer for these applications different adapters. Note that the cylinder is still to the ISO/VDMA standards built-in dimensions. Piston Ø 32 40 50 63 80 00 25 Metal 049640409 049640506 049640506 049640603 049640603 049630305 PTFE 049640700 049640808 049640905 049640905 0496402006 0496402006 0496303202

Tie rod cylinders, Series 523 Accessories Front flange or rear flange (MF/MF2) ISO, VDMA, NFE Piston dia. Part no. E R JS 4 W FB H 3 MF JS 4 TF JS 4 UF ZF Weight [kg] (lbs) 32 523000602 50 32 6 ±,6 7 0 64 80 30 0,3 (0.7) 40 52300602 55 36 20 ±,6 9 0 72 90 45 0,4 (0.9) 50 523200602 65 45 25 ±,6 9 2 90 0 55 0,5 (.) 63 523300602 75 50 25 ±2 9 2 00 25 70,0 (2.2) 80 523400602 00 63 30 ±2 2 6 26 54 90,7 (3.7) 00 523500602 20 75 35 ±2 4 6 50 86 205 2,6 (5.7) 25 523600602 50 90 45 6 20 80 220 245 4, (9.0) 60 5220866002 80 5 60 8 20 230 280 280 7,5 (6.5) 200 5220966002 220 35 70 22 25 270 30 300 3,2 (29.) 250 523900602 280 65 80 26 25 330 380 330 7,0 (37.5) 320 52390602 350 200 90 33 30 400 470 370 3,0 (68.3) Material: Zinc plated steel. Supplied complete with mounting screws for attachment to the cylinder. Piston dia. Part no. E R JS 4 W FB H 3 MF JS 4 TF JS 4 UF ZF Weight [kg] (lbs) 32 523090602 50 32 6 ±,6 7 0 64 80 30 0,25 (0.55) 40 52390602 55 36 20 ±,6 9 0 72 90 45 0,35 (0.77) 50 523290602 65 45 25 ±,6 9 2 90 0 55 0,7 (.5) 63 523390602 75 50 25 ±2 9 2 00 25 70 0,8 (.76) 80 523490602 00 63 30 ±2 2 6 26 54 90,35 (2.98) 00 523590602 20 75 35 ±2 4 6 50 86 205 2,2 (4.85) Material: Anodized aluminum Supplied complete with mounting screws in stainless steel for attachment to the cylinder.

Angle brackets (MS) ISO, VDMA, NFE S* = Stroke Piston dia. Part no. E AB H 4 AH JS 5 AO AT AU ±0,2 SA TR JS 4 XA Weight [kg] (lbs) 32 5230000502 48 7,0 32 5 24 42 ±,25 32 44 0,2 (0.4) 40 523000502 53 9,0 36 2 5 28 6 ±,25 36 63 0,3 (0.7) 50 5232000502 63 9,0 45 3 5 32 70 ±,25 45 75 0,4 (0.9) 63 5233000502 73 9,0 50 3 5 32 85 ±,6 50 90 0,6 (.3) 80 5234000502 98 2,0 63 9 6 4 20 ±,6 63 25,2 (2.6) 00 5235000502 5 4,5 7 9 6 4 220 ±,6 75 230,7 (3.7) 25 5236000502 40 6,5 90 25 8 45 250 90 270 2,6 (5.7) 60 5237000502 80 8,0 5 20 0 60 300 5 320 5,4 (.9) 200 5238000502 220 22,0 35 30 2 70 320 35 345 9,2 (20.3) 250 5239000502 280 26,0 65 40 20 75 350 65 380 3,0 (28.7) 320 523900502 350 35 200 45 24 85 390 200 425 3,0 (68.3) Material: Zinc plated steel. Supplied complete with mounting screws for attachment to the cylinder. The mountings are delivered in pairs. Piston dia. Part no. E AB H 4 AH JS 5 AO AT AU ±0,2 SA TR JS 4 XA Weight [kg] (lbs) 40 523900502 53 9,0 36 9 4 28 6 ±,25 36 63 0,8 (0.40) 50 5232900502 64 9,0 45 0 5 32 70 ±,25 45 75 0,3 (0.66) 63 5233900502 74 9,0 50 2 5 32 85 ±,6 50 90 0,39 (0.86) 80 5234900502 98 2,0 63 9 5 4 20 ±,6 63 25 0,8 (.76) 00 5235900502 5 4 7 9 5 4 220 ±,6 75 230 0,95 (2.09) Material: Stainless steel. Supplied complete with mounting screws in stainless steel for attachment to the cylinder. The mountings are delivered in pairs.

Central male trunnion (MT4) ISO, VDMA, NFE S* = Stroke Piston dia. Part no. Series Grey L TD TL TM UW XV e 9 min. XV max. Weight [kg] (lbs) 32 5230006902 22 2 2 50 60 66,0 80,0+S* 0,2 (0.4) 40 523006902 27 6 6 63 70 77,5 87,5+S* 0,4 (0.9) 50 5232006902 27 6 6 75 85 82,5 97,5+S* 0,5 (.) 63 5233006902 33 20 20 90 00 92,5 02,5+S*,0 (2.2) 80 5234006902 34 20 20 0 20 02,0 8,0+S*,7 (3.7) 00 5235006902 43 25 25 32 40 5,5 24,5+S* 3,0 (6.6) 25 5236006902 43 25 25 60 65 4,5 48,5+S* 4,9 (0.8) Material: Grey cast iron. Piston dia. Part no. Series Green²) Part no. Series Yellow²), Series Red*²) L TD TL TM UW XV e 9 min. XV max. Weight [kg] (lbs) 32 2795000320 279500320 25 2 2 56¹) ±0,8 67¹) 67,5 78,5+S* 0,3 (0.7) 40 2795000400 279500400 28 6 6 63 ±0,8 75 78,0 87,0+S* 0,4 (0.9) 50 2795000500 279500500 28 6 6 75 ±,0 95 83,0 97,0+S* 0,5 (.) 63 2795000630 279500630 36 20 20 90 ±,0 05 94,0 0,0+S* 0,9 (2.0) 80 2795000800 279500800 36 20 20 0 ±,3 30 03,0 7,0+S*,0 (2.2) 00 279500000 27950000 48 25 25 32 ±,3 45 8,0 22,0+S*,6 (3.5) 25 279500250 27950250 50 25 25 60 ±,5 75 45,0 45,0+S* 2, (4.6) ¹) Not according to standard. ²) See table below. * Series red with new profile. Material: Zinc plated steel. ²) Max. axial strength for cylinders with mountings 279-500 and 279-50. Piston Ø Dynamic [kn] (lbf) Static [kn] (lbf) 32,6 (359.7) 3,2 (79,4) 40 2,5 (562.0) 5,0 (24,0) 50 3,9 (876.7) 7,8 (753,4) 63 6,2 (393,8) 2,4 (2787,5) 80 7,5 (686,0) 5,0 (3372,0) 00,8 (2652,6) 23,6 (5305,3) 25 8,4 (436,3) 36,8 (8272,6) Note! When stronger mounting is required, use Series Grey.

Front or rear pivoted mounting (MT5/MT6) ISO S* = Stroke Piston Ø Part no. TD e 9 TL h 4 TM h 4 TT ±0,2 UN max. XH XL Weight [kg] (lbs) 32 523086902 2 2 50 6 50 8 28 0,2 (0.4) 40 52386902 6 6 63 20 55 20 45 0,4 (0.9) 50 523286902 6 6 75 24 65 25 55 0,5 (.) 63 523386902 20 20 90 24 75 25 70,0 (2.2) 80 523486902 20 20 0 28 00 32 88,7 (3.7) 00 523586902 25 25 32 38 23 32 208 2,6 (5.7) 25 523686902 25 25 60 50 45 40 250 4, (9.0) Material: Zinc plated steel. In contrast to the central male trunnion, the pivoted mounting enables a sensor to be mounted for sensing the end position of the cylinder. This mounting can be mounted with dowels on the same side as, or 90 to, the connection port. Note: When the mounting is mounted with dowels on the same side as the connection port, consideration must be given to the space required for the bearing brackets. This mounting is supplied complete with mounting screws for attachment to the cylinder.

Rear end cover clevis (MP0) S* = Stroke Piston dia. Part no. B H 4 B2 d 2 E L R CN F 7 FL ±0,2 XD Weight [kg] (lbs) 32 5230003432 4 34 48,5 0 22 42 0, (0.2) 40 523003432 6 40 53 2,0 3 2 25 60 0,2 (0.4) 50 5232003432 2 45 63 4,0 8 6 27 70 0,3 (0.7) 63 5233003432 2 5 73 4,0 8 6 32 90 0,4 (0.9) 80 5234003432 25 65 98 6,0 22 20 36 20 0,6 (.3) 00 5235003432 25 75 5 6,0 22 20 4 230 0,9 (2.0) 25 5236003432 37 97 40 30,0 30 30 50 275,4 (3.) 60 5237003432 43 22 76 35 36 35 55 35 200 5238003432 43 22 24 45 38 35 60 335 250 5239003432 49 25 274 55 42 40 70 375 Material: Grey cast iron. The mounting is supplied complete with mounting screws for attachment to the cylinder.

Rear eye with PTFE bushing (MP4) ISO, VDMA, NFE S* = Stroke Piston dia. Part no. E L CD H 9 EW FL ±0,2 MR XD Weight [kg] (lbs) 32 82700283 48 4 0 26 0,2/ 0,6 22 42 0, (0.2) 40 82700284 53 6 2 28 0,2/ 0,6 25 3 60 0,2 (0.4) 50 82700285 63 6 2 32 0,2/ 0,6 27 3 70 0,2 (0.4) 63 827020086 73 20 6 40 0,2/ 0,6 32 7 90 0,4 (0.9) 80 82700287 98 22 6 50 0,2/ 0,6 36 7 20 0,6 (.3) 00 82700288 5 27 20 60 0,2/ 0,6 4 2 230,0 (2.2) 25 827004866 40 30 25 70 0,5/,2 50 25 275 4,3 (9.5) 60 827004867 76 35 30 90 0,5/,2 55 30 35 7,9 (7.4) 200 827004868 26 35 30 90 0,5/,2 60 30 335,0 (24.3) 250 827004869 276 45 40 0 0,5/,2 70 40 375 7,0 (37.5) 320 52398342 350 50 45 20 0,5/,2 80 45 420 29,0 (63.9) Material: Ø 32 00 mm Al Mg Si F3 forged, Ø 25 250 mm grey cast iron. The mounting is supplied complete with mounting screws for attachment to the cylinder. Piston dia. Part no. E L CD H 9 EW FL ±0,2 MR XD Weight [kg] (lbs) 32 523090342 48 3 0 26 0,2/ 0,6 22 9 42 0,09 (0.20) 40 52390342 53 6 2 28 0,2/ 0,6 25 2 60 0, (0.24) 50 523290342 63 7 2 32 0,2/ 0,6 27 2 70 0,7 (0.38) 63 523390342 73 22 6 40 0,2/ 0,6 32 5 90 0,24 (0.53) 80 523490342 98 22 6 50 0,2/ 0,6 36 5 20 0,37 (0.82) 00 523590342 5 27 20 60 0,2/ 0,6 4 20 230 0,59 (.30) Material: Aluminum cast, with black CrNi coating. The mounting is supplied complete with mounting screws in stainless steel for attachment to the cylinder.

Rear clevis (MP2) ISO, VDMA, NFE S* = Stroke Piston dia. Part no. E L CB H 4 CD H 9 FL ±0,2 MR UB h 4 XD Weight [kg] (lbs) 32 82700289 48 4 26 0 22 45 42 0, (0.2) 40 523003402 53 6 28 2 25 3 52 60 0,2 (0.4) 50 5232003402 63 6 32 2 27 3 60 70 0,3 (0.7) 63 5233003402 73 20 40 6 32 7 70 90 0,4 (0.9) 80 5234003402 98 22 50 6 36 7 90 20 0,6 (.3) 00 5235003402 5 27 60 20 4 2 0 230 0,9 (2.0) 25 827004862 40 32 70 25 50 25 30 275 4,2 (9.3) 60 827004863 77 35 90 30 55 30 70 35 7,8 (7.2) 200 827004864 26 35 90 30 60 30 70 335 0,8 (23.8) 250 827004865 276 45 0 40 70 40 200 375 6,7 (36.8) 320 523983402 350 50 20 45 80 45 220 420 29 (63.9) Delivered with mounting screws but without pivot pins. Material: Ø 32 00 mm: Al Mg Si F3 forged. Ø 25 250 mm: Grey castings 40 with screws, without the pivot pin. The mounting together with "Rear eye with PTFE bushing" (MP4) + pivot pin (523-X00-009) form a complete pivot mounting. Piston dia. Rear clevis (MP2) corrosion protected Part no. E L CB H 4 CD e 8 FL ±0,2 MR UB h 4 VB XD Weight [kg] (lbs) 32 2798050320 47 2 26 0 22 45 50 42 0, (0.2) 40 2798050400 54 5 28 2 25 3 52 57 60 0,2 (0.4) 50 2798050500 65 5 32 2 27 3 60 65 70 0,2 (0.4) 63 2798050630 75 20 40 6 32 7 70 76 90 0,4 (0.9) 80 2798050800 94 20 50 6 36 7 90 96 20 0,5 (.) 00 279805000 2 25 60 20 4 2 0 7 230 0,9 (2.0) Delivered with pivot pins and mounting screws. Material: Anodized aluminum. Pivot pin, circlips and mounting screws in stainless steel. This mounting together with "Rear eye with PTFE bushing" (MP4) alternative "Rear eye with rubber bushing" (M32) form a complete pivot mounting.

Rear eye with rubber bushing (M32) ISO VDMA, NFE S* = Stroke Piston dia. Part no. E L CD H 9 EW FL MR¹) XD Weight [kg] (lbs) 32 3683203000 46 6,5 0 25,5 22 4,0 42 0, (0.2) 40 3683204000 55 7,5 2 27,0 25 9,0 60 0,2 (0.4) 50 3683205000 62 8,5 2 3,0 27 9,5 70 0,3 (0,7) 63 3683206000 80 2,5 6 39,5 32 26,0 90 0,4 (0.9) 80 3683208000 94 24,5 6 49,5 36 27,0 20 0,5 (.) 00 368320000 4 26,5 20 59,5 4 29,0 230 0,7 (.5) Materials: Aluminum with a bronze bushing encapsulated in vulcanized rubber. The mounting is supplied complete with mounting screws for attachment to the cylinder. ¹) This dimension exceeds the ISO standard.

Rear eye with ball joint (M36) from 80 mm dia. as per ISO VDMA S* = Stroke Piston dia. Part no. Part no.²) Series Yellow E L CD H 7 EX FL MS XD Weight [kg] (lbs) 32 3683603000 2798060320 46 6 0 4 22 7 42 0, (0.2) 40 3683604000 2798060400 55 7 2 6 25 20 60 0,2 (0.4) 50 3683605000 2798060500 62 8 2 6 27 22 70 0,3 (0.7) 63 3683606000 2798060630 80 2 6 2 32 25 90 0,4 (0.9) 80 3683608000 2798060800 94 24 6 2 36 30 20 0,5 (.) 80¹) 5234003452 98 25 20 25 36 27 20 0,7 (.5) 00 368360000 279806000 4 26 20 25 4 32 230 0,9 (2.0) 00¹) 5235003452 5 25 20 25 4 28 230,2 (2.6) 25¹) 5236003452 40 29 30 37 50 40 275 3,8 (8.4) 60¹) 5237003452 80 29 35 43 55 44 35 6,6 (4.6) 200¹) 5238003452 220 28 35 43 60 47 335,6 (25.6) 250¹) 5239003452 280 34 40 49 70 53 375 9,7 (43.4) ¹) To ISO 889 Materials: 32 00 mm dia. aluminum with a steel ball joint, lubrication-free, 25 250 mm dia. grey cast iron. ²) Materials: Anodized aluminum with a steel ball joint, lubrication-free. The mounting is supplied complete with mounting screws for attachment to the cylinder.

Joining piece for building a 3 or 4 position cylinder S* and S2* = Stroke for the respective cylinder. Piston dia. Part no. D d D E max. M ±,25 TG ZJ S + S2 max. 32 5230005902 27 30 50 267 32,5 20 000 40 523005902 27 35 55 297 38,0 35 500 50 5232005902 32 40 65 38 46,5 43 500 63 5233005902 28 45 75 344 56,5 58 500 80 5234005902 38 45 00 386 72,0 74 500 00 5235005902 38 55 20 46 89,0 89 2000 Material: Grey cast iron. Note: Mounting accessories included.

Bearing brackets Piston Ø Part no. A B B C D d h 7 d2 F f H H2 N 32 5230603402 32 5 46 7,5 3,0 2 6,6,2 30 5 6,8 40, 50 5232603402 36 8 55 9,0 3,0 6 9,0 5,6 36 8 9,0 63, 80 5234603402 42 20 65 0,0 3,0 20,0 8,6 40 20,0 00, 25 5236603402 50 25 75 2,5 3,5 25 4,0 20 2,0 50 25 3,0 60, 200 5238603402 60 35 92 7,5 5 32 8 26 2,5 60 30 7,5 250 5239603402 90 50 40 25 6 40 22 33 3,2 70 35 2,5 320 523963402 00 60 50 30 7 50 26 40 3,2 80 40 25,5 Material: Zinc plated steel with sintered bushing. Delivered in pairs.

Bearing block with ball joint and foot Piston Ø Part no. CH JS 5 CN H 7 EN 0/ 0, ER max. EU max. G JS 4 G2 JS 4 G3 max. H6 H max. K JS 4 K2 max. S5 H 3 Weight [kg] (lbs) 32 5230003442 32 0 4 6 0,5 2 8 3 0 6 38 5 6,6 0,9 (0.42) 40 523003442 36 2 6 8 2,0 24 22 35 0 6 4 54 6,6 0,25 (0.55) 50 5232003442 45 6 2 2 5,0 33 30 45 2 23 50 65 9,0 0,46 (.0) 63 5233003442 50 6 2 23 5,0 37 35 50 2 23 52 67 9,0 0,75 (.65) 80 5234003442 63 20 25 28 8,0 47 40 60 4 32 66 86,0,04 (2.29) 00 5235003442 7 20 25 30 8,0 55 50 70 5 33 76 96,0,4 (3.) 25 5236003442 90 30 37 40 25,0 70 60 90 20 50 94 24 4,0 3,6 (6.97) 60 5237003442 5 35 43 44 30 97 88 26 25 70 8 56 4 6,4 (4.) 200 5238003442 35 35 43 47 30 05 90 30 30 90 22 62 8 9, (20.) 250 5239003442 65 40 49 53 35 28 0 60 35 5 50 200 22 3,4 (29.5) 320 523903442 200 50 60 63 45 50 22 86 40 40 70 234 26 6,9 (37.3) Material: Grey cast iron. Note: Mounting accessories included.

Bolts with anti-rotation device (for "Rear end cover clevis" 523-X00-343-2) VDMA, NFE Piston Ø Part no. A B C D3 0/ 0, D4 H 2 EK h 9 L +0,2/0 L2 L3 L4 0/ 0,4 Weight [kg] (lbs) 32 5230000082 8 22,0 0 0 3 0 32,5 4,5 4 4 0,03 (0.07) 40 523000082 22 26,0 2 2 4 2 38,0 5,0 48 6 0,05 (0.) 50 5232000082 28 34,5 6 6 4 6 43,0 6,0 54 20 0,0 (0.22) 63 5233000082 28 34,5 6 6 4 6 49,0 6,0 60 20 0, (0.24) 80 5234000082 28 34,5 6 6 4 20 63,0 6,0 74 24 0,5 (0.33) 00 5235000082 28 34,5 6 6 4 20 73,0 6,0 84 24 0,20 (0.44) 25 5236000082 * * * 30 6 30 94,0 5,0 06 36 0,59 (.30) 60 5237000082 35 6 35 9 5,0 3 4,3 (2.49) 200 5237000082 35 6 35 9 5,0 3 4,3 (2.49) 250 5239000082 40 8 40 2 6,0 37 48 2,20 (4.85) 320 523900082 50 8 50 46 7,0 63 58 3,0 (6.83) Material: Hardened steel. Note: For "Bearing block with ball joint and foot" (523-X00-344-2) mounted together with "Rear end cover clevis" (523-X00-343-2). * Locking ring to DIN 47, NFE 22-63.

Bearing block with fixed bearing and foot VDMA, NFE Piston dia. Part no. CA JS 5 CK H 9 EM G G2 JS 4 G3 H6 K JS 4 K2 max. L3 max. R max. S5 Weight [kg] (lbs) 32 5230003422 32 0 26 0,2/ 0,6 2 8 3 8 38 5 0 0,0 6,6 0,7 (0.38) 40 523003422 36 2 28 0,2/ 0,6 24 22 35 0 4 54 2,0 6,6 0,2 (0.46) 50 5232003422 45 2 32 0,2/ 0,6 33 30 45 2 50 65 6 3,0 9,0 0,44 (0.97) 63 5233003422 50 6 40 0,2/ 0,6 37 35 50 2 52 67 6 5,0 9,0 0,54 (.9) 80 5234003422 63 6 50 0,2/ 0,6 47 40 60 4 66 86 20 5,0,0 0,96 (2.2) 00 5235003422 7 20 60 0,2/ 0,6 55 50 70 5 76 96 20 9,0,0,37 (3.02) 25 5236003422 90 25 70 0,5/,2 70 60 90 20 94 24 30 22,5 4,0 2,98 (6.57) 60 5237003422 5 30 90 0,5/,2 97 88 26 25 8 56 36 3,5 4,0 200 5238003422 35 30 90 0,5/,2 05 90 30 30 22 62 40 3,5 8,0 250 5239003422 65 40 0 0,5/,2 28 0 60 35 50 200 45 40,0 22,0 Material: Painted grey cast iron. Piston dia. Corrosion resistant version Part no. CA JS 5 CK H 9 EM G G2 JS 4 G3 H6 K JS 4 K2 max. L3 max. R max. S5 Weight [kg] (lbs) 32 5230903422 32 0 26 0,2/ 0,6 2 8 3 8 38 5 0 0,0 6,6 0,05 (.) 40 523903422 36 2 28 0,2/ 0,6 24 22 35 0 4 54 2,0 6,6 0,07 (0.5) 50 5232903422 45 2 32 0,2/ 0,6 33 30 45 2 50 65 6 3,0 9,0 0,4 (0.3) 63 5233903422 50 6 40 0,2/ 0,6 37 35 50 2 52 67 6 5,0 9,0 0,8 (0.40) 80 5234903422 63 6 50 0,2/ 0,6 47 40 60 4 66 86 20 5,0,0 0,28 (0.62) 00 5235903422 7 20 60 0,2/ 0,6 55 50 70 5 76 96 20 9,0,0 0,42 (0.93) Material: Aluminum cast with black CrNi coating.

Bolts with locking rings (for "Rear Clevis" (MP2) 523-XX0-340-2) VDMA, NFE Piston Ø Fig. Part no. A D max. EK d 0 EL Weight [kg] (lbs) 32 5230000092 9,0 56 0 46 0/+ 0,03 (0.07) 40 523000092 2,0 63 2 53 0/+ 0,05 (0.) 50 5232000092 2,0 73 2 6 0/+ 0,06 (0.3) 63 5233000092 27,6 85 6 7 0/+ 0,2 (0.27) 80 5234000092 27,6 05 6 9 0/+ 0,6 (0.35) 00 5235000092 40,0 29 20 0/+ 0,27 (0.60) 25 5236000092 40,0 50 25 32 0/+2 0,5 (.2) 60 5237000092 40,5 88 30 72 0/+2,05 (2.32) 200 5237000092 40,5 88 30 72 0/+2,05 250 2 5239000092 52,6 28 40 202 0/+2 2,50 320 2 523900092 59, 238 45 225,5 0/+2 3,05 Material: Stainless steel. Note: For "Rear eye with PTFE bushing" (MP4) 523-XX0-34-2 or "Bearing block with fixed bearing" 523-X00-342-2 mounted together with "Rear Clevis" MP2 (523-XX0-340-2).

Bearing brackets, lubrication-free * The maximum pendulum movement with rear eye is ±45. CR H 8 Part no. Part no. for yellow series¹) EA FA FK ±0, FN HB NH TH UL Weight [kg] (lbs) 0 367202000 279840320 6 0 2 29 5,5 0 27 37 0,08 (0.8) 2 367203000 279840400 9 22 32 6,6 44 55 0,6 (0.35) 6 367204000 279840630 28 6 35 49 9,0 6 65 82 0,50 (.0) 20 367206000 27984000 38 9 40 59 9,0 9 80 99 0,80 (.76) 25 36720000 46 22 48 7,0 22 96 8,30 (2.87) 30 36722000 56 28 57 88 3,0 28 4 42 2,40 (5.29) 32 36726000 66 32 70 03 7,0 32 40 72 4,40 (9.70) 35 367220000 66 32 70 03 7,0 32 40 72 4,40 (9.70) Material: Aluminum with steel bushings provided with a plastic surface coating, intended for normal loading cases. ¹) Material: Anodized aluminum with steel bushings provided with a plastic surface coating, intended for normal loading cases. Note: For mounting together with "Ball eye rod end" or, alternatively, "Central male trunnion", "pivoted mounting" or "rear eye". For "Ball eye rod end" and "Rear eye" a pivot pin kit is also required.

Steel bearing brackets * The maximum pendulum movement with rear eye is ±45. Axle CR H 8 Part no. EA FA FK ±0, FN HB NH TH UL Weight [kg] (lbs) 0 366202000 6 0 2 29 5,5 0 27 37 0,08 (0.8) 2 366203000 9 22 32 6,6 44 55 0,6 (0.35) 6 366204000 28 6 35 49 9,0 6 65 82 0,50 (.0) 20 366206000 38 9 40 59 9,0 9 80 99 0,80 (.76) 25 36620000 46 22 48 7,0 22 96 8,30 (2.87 30 36622000 56 28 57 85 3,0 28 4 42 2,40 (5.29) 32 36626000 66 32 70 03 7,0 32 40 72 4,40 (9.7) 35 366220000 66 32 70 03 7,0 32 40 72 4,40 (9.7 Material: Zinc plated steel. Intended for more difficult loading cases and in conjunction with high temperature cylinders. For mounting together with "Ball eye rod end" or, alternatively, "Central male trunnion", "Pivoted mounting" or "Rear eye". For "Ball eye rod end" and "Rear eye" a pivot pin kit is also required.

Pivot pin kit (for "Bearing brackets" 36720x000 and 36620x000) Part no. Part no.¹) corrosion resistant CN AN AD AP Weight e 8 [kg] (lbs) 368302000 279802000 0 24,2 33,5 39 0,03 368304000 279802020 2 27,5 37,8 44 0,05 368305000 279802060 6 37,5 52,8 59 0, 368308000 2798020200 20 44,5 62,8 70 0,8 Material: Hardened steel. ¹) Material: Stainless steel. For mounting together with "Ball eye rod end (P4)" 895820XXX0 or, alternatively, "Rear eye with ball joint (M36)" 368360X000. The pivot pin is delivered with circlips.

Nut Piston Ø Part no. Surface treated steel¹) Part no. Stainless steel²) KT KU Weight [kg] (lbs) M0x,25 3670302000 3590302000 7 5 0,008 (0.08) M2x,25 3670304000 3590304000 9 6 0,04 (0.03) M6x,5 3670305000 3590305000 24 8 0,024 (0.053) M20x,5 3670308000 3590308000 30 0 0,045 (0.099) M24x2 367032000 36 2 0,060 (0.32) M27x2 364032000 42 2 0,070 (0.54) M36x2 367036000 50 6 0,50 (0.33) M42x2 3670325000 60 2 0,300 (0.66) M48x2 3670332000 65 25 0,400 (0.882) ¹) Material: Zinc plated steel (M 0-M 36). Phosphated and oiled steel for M 42x2 and M 48x2. ²) Material: Stainless steel (BS 303 S 3). Note: Piston nuts are mounted on all cylinders.

Rod clevis (P) ISO 840 cyl.- Ø Thread KK Fig. CL D CK CM LE ER CE L BL Code 32 M 0 20 0 0 0 20 2 40 5 26 895800022 32 M 0 x,25 2 20 8 0 0 20 2 40 5 26 82222024 40 M2x,25 2 24 20 2 2 24 4 48 8 3 82222025 50/63 M6x,5 2 32 26 6 6 32 9 64 24 39 82222005 80/00 M 20 x,5 2 40 34 20 20 40 20 80 30 49 82222004 25 M 27 x 2 55 48 30 30 54 38 0 38 73 82700493 60/200 M36x2 3 70 60 35 35 72 44 44 9 8270047 250 M42x2 3 85 70 40 40 84 64 68 06 82700472 320 M48x2 3 96 82 50 50 96 73 92 2 895809332 Material: Zinc plated steel.

Rod clevis in stainless steel (P2) ISO 840 Thread KK Part no.¹) BL CE CK e 8 CL CM B 2 ER LE KT KU Weight [kg] (lbs) M0x,25 3590502000 25 40 0 20 0 2 20 7 5 0, (0.2) M2x,25 3590504000 30 48 2 24 2 4 24 9 8 0,2 (0.4) M6x,5 3590505000 38 64 6 32 6 9 32 24 8 0,4 (0.9) M20x,5 3590508000 47 80 20 40 20 25 40 30 0 0,7 (.5) Material: Stainless steel (BS 303 S 3). ¹) The mounting has a lock nut to lock it in the set position.

Mounting plate (P3) Thread KK Part no. A B C D E F H Weight [kg] (lbs) M0x,25 3670803000 9 M6 29 9,0 30 5 24 0,55 (.2) M2x,25 3670804000 2 M6 34 22,5 36 5 26 0,08 (0.76) M6x,5 3670805000 2 M8 44 30,0 46 5 32 0,4 (0.309) Material: Anodized aluminum. The mounting is delivered complete with screws for locking on the piston rod. Intended for mounting "tools" on the piston rod.

Ball eye rod end (P4) ISO VDMA AFNOR Piston Ø Thread KK Part no.¹) AA AV CE CN H 7 EN 0/ 0, EU ER max. F H LF α Weight [kg] (lbs) 32 M 0x,25 82224003 9 20 43 0 4 0,5 4 2,9 7 5 26 0, (0.2) 40 M2x,25 82224004 22 22 50 2 6 2 6 5,4 9 7 26 0,2 (0.4) 50, 63 M6x,5 82224005 29 28 64 6 2 5 2 9,3 22 22 30 0,4 (0.9) 80, 00 M 20x,5 82224006 34 33 77 20 25 8 25 24,3 32 26 30 0,5 (.) 25 M 27x2 8222403 52 5 0 30 37 25 35 34,8 4 36 30, (2.4) 60, 200 M36x2 82224008 58 56 25 35 43 28 40 37,7 50 37 6,2 (2.6) 250 M42x2 82224009 58 60 42 40 49 33 45 45,2 55 42 7 2,6 (5.7) 320 M48x2 8958208842 70 65 60 50 60 45 58 56,6 65 60 2 5,2 (2) Material: Zinc plated steel with hardened swivel bearing (maintenance-free). ¹) to ISO 839. Piston Ø Ball eye rod end (P4), corrosion-resistant Thread KK Part no.¹) AA AV CE CN H 7 EN 0/ 0, EU ER max. F LF H Weight [kg] (lbs) 32 M 0x,25 8958209032 9 5 43 0 4 0,5 4,5 2,9 4 7 0,07 (.5) 40 M2x,25 8958209042 22 8 50 2 6 2,0 6,5 5,4 6 9 0,0 (0.22) 50, 63 M6x,5 8958209052 24 24 64 6 2 5,0 2,5 9,3 2 22 0,2 (0.46) 80, 00 M 20x,5 8958209062 34 30 77 20 25 8,0 25,5 24,3 25 30 0,38 (0.84) 25 M 27x2 8958209072 50 45 0 30 37 25 35,5 34,8 35 4,5 (2.54) Material: Stainless steel, non-ferrous metal free. ¹) to ISO 839.

Flexible coupling (P5) * Angular displacement of center line. ** Radial displacement of center line. Thread KK Part no. B D D2 D3 F min. L ±2 L2 L3 ± SW SW2 SW3 SW4 RV M0x,25 826409002 6,0 2,5 34 4 23 70 20 7,5 9 2 7 30 0,7 M2x,25 826409003 7,0 2,5 34 4 24 75 24 3,0 9 2 9 30 0,7 M6x,5 826409004 8,0 33,5 47 22 32 03 32 9,0 30 9 24 4,0 M20x,5 826409005 0,0 33,5 47 22 4 20 40 9,0 30 9 30 4,0 M27x2 826409006 3,5 62,0 62 28 42 57 54 4,0 55 24 4 55 5,0 M36x2 826409007 8 80 80 38 78 25 72 75 32 55 75 7,0 Material: Zinc plated steel.

Flexible coupling with mounting plate (B) Axial play: 0,4... 0,8 mm (Ø32 25); 0,4... 0,95 mm (60 / 200) Radial play: 2...4 mm (Ø32 25); 3 mm (60 / 200) Material: Steel, galvanized Piston Ø Part no. KK a a2 d H d6 H3 d7 H3 e H3 e2 h t2 H SW Weight [kg] (lbs) 32 82700629 M0x,25 60 37 20 6,6 36±0,5 23±0,5 5 7 24 7 0,300 (0.66) 40 82700630 M2x,25 60 56 25 9 5 42±0,2 38±0,2 20 9 30 9 0,400 (0.88) 50 8270063 M6x,5 80 80 30 8 58±0,2 58±0,2 20 32 24 0,900 (.98) 63 8270063 M6x,5 80 80 30 8 58±0,2 58±0,2 20 32 24 0,900 (.98) 80 82700632 M20x,5 90 90 40 4 20 65±0,3 65±0,3 20 3 35 36,50 (2.54) 00 82700632 M20x,5 90 90 40 4 20 65±0,3 65±0,3 20 3 35 36,50 (2.54) 25 82700633 M27x2 90 90 40 4 20 65±0,3 65±0,3 20 3 35 36,00 (2.43) 60 82700634 M36x2 25 25 60 8 26 90±0,3 90±0,3 30 7 55 50 3,400 (7.5) 200 82700634 M36x2 25 25 60 8 26 90±0,3 90±0,3 30 7 55 50 3,400 (7.5)

Tie rod cylinders, Series 523 Linear control units Linear control unit, H-shape Type Standard H-shape Linear control units suitable for cylinders Ambient temperature range as per ISO 6432, VDMA 24562 and CNOMO / NFE 49-003 -20 C to +80 C (-4 F to +76 F) Materials Bearing housing Anodized aluminum Carrying plate Anodized aluminum Control rods for Stainless steel, smooth-rolled plain bearing Flexible coupling in the Stainless steel, smooth-rolled carrying plate Plain bearing Sintered bronze Ball bearing Steel Screws Galvanized steel Application area Guide unit reduces bending of the piston rod when positioning high loads High precision due to long guide High useful load due to solid guide rods Technical information Piston Ø (inch) 32 (¼") 40 (½") 50 (2") 63 (2½") 80 (3") 00 (4") Weight 0 mm stroke [kg],300 2,300 3,700 4,700 8,800,00 (lbs) (2.866) (5.07) (8.57) (0.362) (9.40) (24.47) H-shape, ball bearing add. per 00 mm [kg] 0,090 0,60 0,250 0,250 0,390 0,390 (lbs) (0.98) (0.353) (0.55) (0.55) (0.860) (0.860) Weight 0 mm stroke [kg],300 2,300 3,700 4,700 8,800,00 (lbs) (2.866) (5.07) (8.57) (0.362) (9.40) (24.47) H-shape, plain bearing add. per 00 mm [kg] 0,090 0,60 0,250 0,250 0,390 0,390 (lbs) (0.98) (0.353) (0.55) (0.55) (0.860) (0.860) Part no. H-shape, sinter friction bearing (L) For piston dia. 32 40 50 63 80 00 Stroke 50 08240220 08240230 08240240 08240280 - - 00 0824022 0824023 0824024 0824028 08240260 08240270 60 08240222 08240232 08240242 08240285 - - 200 08240223 08240233 08240243 08240282 0824026 0824027 250 08240224 08240234 08240244 08240286 - - 320 08240225 08240235 08240245 08240283 08240262 08240272 400 08240226 08240236 08240246 08240287 - - 500 08240227 08240237 08240247 08240284 08240263 08240273 600 08240228 08240238 08240249 08240288 08240264 08240274 800 08240229 08240239 08240474 08240289 08240265 08240275 000 08240470 08240472 08240475 08240290 08240266 08240276 200 0824047 08240473 08240476 0824029 08240267 08240277 Rec. max. stroke 200 200 200 200 200 200 Spare parts kit (to be ordered separately) Piston dia. Order no. 32 82700945 40 82700946 50 827009530 63 827009530 80 827009535 00 827009535

Tie rod cylinders, Series 523 Linear control units Part no. H-shape, linear ball bearings (L5) For piston dia. 32 40 50 63 80 00 Stroke 50 08240320 08240330 08240340 08240380 00 0824032 0824033 0824034 0824038 08240360 08240370 200 08240322 08240332 08240342 08240382 0824036 0824037 320 08240323 08240333 08240343 08240383 08240362 08240372 500 08240324 08240334 08240344 08240384 08240363 08240373 600 08240325 08240335 08240345 08240385 08240364 08240374 800 08240326 08240336 08240346 08240386 08240365 08240375 000 08240327 08240337 08240347 08240387 08240366 08240376 200 08240328 08240338 08240348 08240388 08240367 08240377 Rec. max. stroke 200 200 200 200 200 200 Spare parts kit (to be ordered separately) Piston dia. Part no. 32 827009526 40 827009527 50 827009528 63 827009528 80 827009529 00 827009529 A 2

Tie rod cylinders, Series 523 Linear control units H = Stroke Relubricate ball bearings after 5000 km (lubricating grease KP2K DIN 5825), order no. 82999099 Lubricate more often in dusty conditions Piston dia. A A2 A3 A4 A5 B C G G2 G3 G4 L L2 L3 L4 L5 L6 L7 L8 L9 L0 L L2 *,2 32 78 32,5 6 8 50 2 74 M6 6,6 6,5 90 45 97 77 25 6 7 2 94 7 4,3 64 +5 40 84 38 69 99 54 6 87 M6 6,6 6,5 0 54 5 92 40 7 22 2 05 2 74 +5 50 00 46,5 85 9 72 20 04 M8 9 5 9 30 63 37 205 50 8 26 5 06 26 8,8 89 +0 63 05 56,5 00 32 82 20 9 M8 9 5 9 45 80 52 237 82 8 26 5 2 26 5,3 89 +0 80 30 72 30 66 06 25 48 M0 8 80 00 89 280 25 9 32 20 28 34 2 0 +0 00 50 89 50 90 3 25 72 M0 8 200 20 23 280 220 9 32 20 38 39 24,5 5 +0 Piston dia. L3 L4 L5 *2 L7 L8 M8 L9 *2 L9A *3 *2 L20 L2 L22 SW SW 2 R R2 H7 E + F + ØG +0,5 ØH SW T 32 50 76 37 50,2 +0,4 30 4 2 SW30 6 6,2 3 7 6 5 7 6 5 5 4 40 58 8 37 58,2 +0,4 35 8 9 45 4 9 5 9 6 6 8 7 6 6 4 50 70 79 37 70,2 +0,4 40 36 +8 54 4 23,2 22 24 6 6 8 7 6 6 6 63 85 37 85,2 +0,4 45 2 +2 54 4 28,2 22 24 6 6 8 7 6 6 6 80 05 28 42 05,4 +0,6 45 34 +4 60 4 36 27 30 6 7 9 9,4 8 8 20 00 30 28 37 30,4 +0,6 55 9 2 60 4 44,5 27 30 6 7 9 9,4 8 8 20 These values apply for linear ball bearings as well as for sinter-friction bearings. For differing values, see below. * Change the adjustment range of the flexible coupling accordingly (see L5 and L9) *2 For retracted cylinder **3 Cylinders without signal 3

Tie rod cylinders, Series 523 Linear control units Piston dia. L5 *2 These values apply 32 37 4 2 77 for sinter-friction 40 37 8 9 92 bearings 50 37 4 4 205 63 37 2 +2 237 80 42 34 +4 280 00 37 9 2 280 L9 *2 L9A *3 *2 L4 4

Tie rod cylinders, Series 523 Linear control units Useful load Useful load for linear control units with sinter friction bearings F = Useful load Z = Bearing-out Useful load Service life 2 x 0 6 m Useful load for linear control units with linear ball bearings F = Useful load Z = Bearing-out 5

Tie rod cylinders, Series 523 Linear control units Reduction of useful load on short strokes k = adjustment factor: normal = ; on impact: 2 The nominal load data determined for short-stroke movements from the diagram have to be multiplied with the adjustment factor k. These short-stroke adjustments are already included in the load diagram for a bearing-out of more than 60 mm. Service life 5 x 0 6 m F permit = F x 0,5 Bending F = Useful load (at the load center) SF = Bending Z = Bearing-out 6

Tie rod cylinders, Series 523 Linear control units Bending due to own load Bending due to 0 N load 7

Tie rod cylinders, Series 523 Sensors Sensors Series ST8 (275) * LED Technical Data Outlet PNP with cable NPN, PNP with connector Reed with cable Reed with connector Voltage and type of current 0-30 V DC 0-30 V DC 0-30 V DC,240 V AC 0 30 V DC Max. continuous current <50 ma <50 ma <00 ma <00 ma Voltage drop <2 V <2 V <3 V <3 V Leakage current 0 µa 0 µa Internal consumption 0 ma 0 ma Ambient temperature range -25 C to +75 C (-3 F to +67 F) -25 C to +75 C (-3 F to +67 F) -25 C to +75 C (-3 F to +67 F) -25 C to +75 C (-3 F to +67 F) Protection* IP 67 as per IEC 529 IP 67 as per IEC 529 IP 67 as per IEC 529 IP 67 as per IEC 529 Indication LED LED LED LED De-energization delay >20 ms >20 ms Material Housing: Polyamide Cable: PVC (3x0,4 mm²) Housing: Polyamide Cable: PUR (3x0,4 mm²) Housing: Polyamide Cable: PVC (2x0,4 mm²) * When used with threaded IP 67 connector, see figures 3 and 4 for cables with connector. Housing: Polyamide Cable: PUR (2x0,4 mm²) Part no. (for Ø 32-25mm)** Symbol Type Fig. Part no. Cable length L [m] Reed - R 27503230 2,5 Reed - R2 27505230 0 Reed - R3 2 2750320 0,3 + M8 connector PNP - I 275030 2,5 PNP - I2 275050 0 PNP - I3 2 275020 0,3 + M8 connector PNP - I4 2 27502320 0,3 + M8 connector* PNP - I4 3 27502320 Micro (0,3 m + M8 connector) PNP - I5 4 2750220 0,3 + M2 connector NPN - I6 2 2750220 0,3 + M8 connector * As per EN 50082-2 ** For 60 320 mm dia., order Proximity Reed Switch with LED, part no. 89404062.. Brown 2. Blue 3. Black 4. Load/signal

Sensor mounting for the Red series (profile version 06) Piston Ø Part no. 32 00 523006352 Material: Anodized aluminum and stainless steel.

Sensor with cable, CE-marked, inductive for the Grey series 60 320 mm dia. ) Cable: black 2,5 m long, extremely flexible 2) Switching point 3) Load BK = Black BU = Blue BN = Brown Part no. Ambient temp. Range 89404522-25 C to +75 C (- Operating voltage Switching current 3 F to +67 F) - Degree of protection: IP 67 - IEC 529 with cable (DIN VDE 0470) - Hysteresis: max. mm - Output: Polarity safe, short-circuit protection - Indicator: 2 LEDs (green = supply voltage, (yellow = operation status) - Body: Plastic (PEI) Function range Extended pulse Contact type 0 30 V DC 200 ma (max) 2 35 mt 20 ms PNP (Normally open)

Sensor with cable and LED, reed ) Cable-black, extremely flexible. 2) Switching point. 3) Load. BK = black BN = brown Part no. Length of cable Ambient temperature range 894045302 2,5 m -25 C to +75 C (- 3 F to +67 F) 894045322 6 m -25 C to +75 C (- Operating voltage 3 F to +67 F) - Degree of protection: IP 67 - IEC 529 with cable (DIN VDE 0470) - Passing speed, max:,5 m/s - Switching capacity, with LED: 50 W / 50 VA, without LED: 20 W / 30 VA - Output: Polarity safe, surge protected - Switch point accuracy: ±0, mm - Indicator: LED (yellow = operating status) - Body: Plastic (PEI) Switching current, max Max. peak voltage Contact type 0 250 V AC/DC 0,5 A 500 V Normally open 0 250 V AC/DC 0,5 A 500 V Normally open

Sensor with connector, CE-marked, inductive for the Grey series 60 320 mm dia. ) Switching point. 2) Load. Part no. Ambient temp. Range 89404532-25 C to +75 C (- Operating voltage 3 F to +67 F) - Degree of protection: IP 65 - IEC 529 with plug (DIN VDE 0470) - Hysteresis: max. mm - Output: Polarity safe, short-circuit protection - Indicator: 2 LEDs (green = supply voltage, yellow = operation status) - Body: Plastic (PEI) Switching current Function range Extended pulse Contact type 0 30 V DC 200 ma (max) 2 35 mt 20 ms PNP (Normally open)

Sensor with connector and LED, reed ) Switching point. 2) Load. Part no. Ambient temperature range 894045392-25 C to +75 C (- Operating voltage Switching current, max 3 F to +67 F) - Degree of protection: IP 65 - IEC 529 with plug (DIN VDE 0470) - Passing speed, max:,5 m/s - Switching capacity,with LED: 50 W / 50 VA, without LED: 20 W / 30 VA - Switching point accuracy: ±0, mm - Indicator: LED (yellow = operating status) - Body: Plastic (PEI) Max. peak voltage Nominal voltage 0 250 V AC/DC 0,5 A 500 V 0 60 V AC 75 V DC Contact type Normally open

Sensor mounting for the Grey series 60 250 mm dia. Piston Ø Part no. X Y Z 60 to 200 3220973502 4,4 7 20 250 322089352 46,7 2 33 For proximity reed switches 89404522, -53-2

Sensor with encapsulated cable, reed for the Grey series 60 320 mm dia. ) Switching point in the middle of this side. 2) LED (yellow). 3) LOAD. BK = Black BU = Blue BN = Brown Part no. Nominal voltage Ambient temp. range Type Fig. I* [A] 894042022 0 250 V AC/DC -25 C to +75 C (-3 F to +67 F) 894042032 0 250 V AC/DC -25 C to +75 C (-3 F to +67 F) 89404902 250 V AC/DC max. -20 C to +20 C (-4 F to +248 F) Degree of protection with plug: IP 67 - IEC 529 (DIN VDE 0470) Max. peak voltage: 500 Vs Passing speed max.:,5 m/s Switching point accuracy: ±0, mm Impact resistance: 50 g ( ms) Vibration resistance: 35 g (50 000 Hz) * Max. switching current Cable (black) [m] Switching capacity LED 0,5 2,5 50 W / 50 VA LED 0,5 6 50 W / 50 VA 2 3 2,5 60 W / 60 VA

Proximity reed switch for electrical connector for the Grey series 60 320 mm dia. ) Switching point in the middle of this side. 2) LED (yellow). 3) LOAD. Supplied with gasket. Mounting screw M 4 supplied with the clamp (MA =,5 Nm) MA = torque at mounting screw. Part no. Type Fig. Ambient temp. range 894040602 without LED -25 C to +75 C (-3 F to +67 F) 89404062 with LED 2-25 C to +75 C (-3 F to +67 F) Degree of protection with plug: IP 65 - IEC 529 (DIN VDE 0470) Max. peak voltage: 500 Vs Passing speed max.:,5 m/s Switching point accuracy: ±0, mm Impact resistance: 50 g ( ms) Vibration resistance: 35 g (50 000 Hz) Nominal voltage Switching current max. [A] Switching capacity 0 250 V AC/DC max. 3 60 W / 60 VA 0 250 V AC/DC max. 0,5 50 W / 50 VA

Clamp for Cylinder Series 523 for the Grey series 60 320 mm dia. Piston Ø Part no. A B C D F G G2 H 60 to 200 3220673522 32 32 22 23 M 4 M6 6 250 to 320 3220893502 36 4 30 6 23 M 4 M6 6 Mounting screws for clamp and proximity reed switch are supplied. Figs. and 2 for proximity reed switches 894040602, -06-2, -90-2, -202-2, -203-2

Circular connector with cable for sensors Series ST8 and 89404532 * by 5 m cable dia. 2 mm BK = Black BU = Blue BN = Brown Length of cable L [m] Part no. Fig. angled Part no. Fig. 2 straight Part no. Fig. 3 angled with thread Part no. Fig. 4 straight with thread 5 894606202 89460602 894620402 894620302 2 89460622 8946062 89462042 89462032 0 894606222 89460622 894620422 894620322 5 894606232 89460632 894620432 894620332 - Operating voltage: 30 V AC / 36 V DC - Degree of protection: IP 65 - IEC 529 (DIN VDE 0470) - Cross section of cable: 3 x 0,25 mm², 3 x 0,34 mm² by 5 m cable with thread - Piping type: PVC - hose (black) - Insulation class: C to VDE 00

Connector for sensor 8940406X2 Part no. Nominal voltage Pins Operating voltage 894004702 max. 250 V 3 60 V AC /75 V DC Degree of protection: IP 65 - IEC 529 (DIN VDE 0470).

Tie rod cylinders, Series 523 Accessories Base plate for direct mounting of ISO valves Piston Ø Part no. Valve size Port nos., 2, 4, 3, (5) Port nos. 2, 4 A B C D E F G H K Weight [kg] (lbs) 32 25 580690000 ISO G /8 G /8 93,5 80 62 35 8 9 20 5 40 0,75 (0.386) 63 25 5802690000 ISO 2 G 3/8 G /8 27 09,5 8,5 46,5,5 3 32 29 60 0,580 (.279) Installation Instructions Connection: Outlet port 2 of the valve should be connected to the end cover where the base plate is fitted. Outlet port 4 is connected to the opposite end cover with tubing. Exhaust ports 3 and 5 are combined in the plate to a common exhaust port. Inlet port and control ports 2 and 4 are located on one side of the plate. Flow: The maximum flow for a valve mounted on these base plates is somewhat lower than for a valve mounted on a normal base plate. Installation: The plate is fitted directly on the front or rear end cover of the cylinder with a banjo thread. Alternatively one or the other of the two banjo threads (G /8 and G /4) supplied for base plate 580-69 can be used, depending on the size of the cylinder port. A size G 3/8 banjo thread is supplied for base plate 580-269. For cylinders 00 and 25 mm (4" and 5" inch) dia., a reducing nipple for the cylinder connection port G /2 is required. Min. strokes: The table below shows the smallest stroke which a cylinder can have when the base plate is turned towards the opposite end cover and connected with fittings and plastic tubing; 6 mm dia. for 580-69 and 2 mm (/2" inch) dia. for 580-269. Piston Ø Minimum strokes Valve 32 50 ISO 40 50 ISO 50 50 ISO 63 00 ISO, ISO 2 80 00 ISO, ISO 2 00 00 ISO, ISO 2 25 00 ISO, ISO 2

Base plate for direct mounting of Compact 0 or Compact 8 valves Version Part no. Valve size Port nos., 4 Port nos. 3, 5 A B C D E F G H K L M Weight [kg] (lbs) Upright 0493839705 258 G /8 G /8 79 65,5 48 33 8 8 6,5 28,5 9 8 0,08 (0.8) 04938408 250 M 7 G /8 79 65,5 42,5 33 26 4 23/25 32,5 4 9 3 0,09 (0.20)