Dairy Transport Assurance Scheme
|
|
- Laurence Lang
- 5 years ago
- Views:
Transcription
1 Dairy Transport Assurance Scheme Codes of Practice on Milk Tanker Design April 2018 (Version 3) Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
2 DAIRY UK CODES OF PRACTICE ON MILK TANKER DESIGN CONTENTS REGULATION 2 FOREWORD 2 1. VACUUM LOADING PRESSURE DISCHARGE RIGID MILK COLLECTION TANKER 3 2. ATMOSPHERIC PUMP LOADING / DISCHARGE RIGID / ARTICULATED MILK COLLECTION TANKER 3. APPROVED RELOAD / BULK TANKER 14 9 REGULATION All tanks must conform to current legislation for build and food hygiene specification for tanks for the transport of milk and milk products. BS 3441 (1995) Food Hygiene Regulation (Ec) No. 852/2004, No. 853/2004 Dairy Uk DTAS (Dairy Transport Assurance Scheme) FOREWORD This Code of Practice sets down the guide lines and the minimum requirements for the design and build of any Milk Tanker that will be used under the Dairy Transport Assurance Scheme (DTAS). This document is to be used in conjunction with the above legislative documents and is in no way a replacement or substitute on its own. The purpose of this document is to highlight the " " agreed between the major Milk Companies, Tank Manufacturers and Operators in the UK and is endorsed by the UK Trade body for the Dairy Industry namely "Dairy UK". It is agreed that this COP does not, and should not, restrict any future design or improvements. However, any changes out with the COP standard must be approved by Dairy UK before they are included into any build programme. All due consideration will be given to any proposed design changes with an agreement that they will not be unreasonably refused. It is the responsibility of all concerned in the design change to seek approval from Dairy UK as failure to do so could result in a breach of the DTAS document. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
3 1. VACUUM LOADING PRESSURE DISCHARGE RIGID MILK COLLECTION TANKER Code of Practice 1 Capacity As per customers requirement +/- 1% ullage. 2 General Dimensions To operate at customers requirement. Length Length as per current Road use Regulations. Height. Height as per Requirement but must be within current Road use Regulations. Slope to rear Slope to Rear 1.5º. 3 Test Pressure 4 Barrel 5 Baffle 6 Dished Ends 7 Stiffening Rings 8 Pipe Work and Connections. 9 Spill Box Working Pressure Must be less than 0.5 bar if 0.5 or more PED and PSSR apply. Test Pressure 0.75 bar. Working Vacuum 460mm Hg. Test Vacuum. 510mm Hg. Full Material 304 stainless steel or other Food Grade steel of comparable strength. Thickness 3mm. Barrel type Straight cylindrical single compartment. Internal finish Welds ground and polished to 2B surface finish as per BS stainless steel or other food grade steel of comparable strength. Thickness 3mm. No of baffles 1 No. (Preferred ). Baffle features Adequate cut out for access to both compartments. Top cut out for venting. Bottom cut out for drainage. Side Drain Holes 3 & 9 o clock Cleaning Rings 3mm 304L stainless steel or other food grade steel of comparable strength may be used with top and bottom 3/4 test sockets, PVC bottom catch tube. 304 stainless steel or other suitable food grade materials of comparable strength may be used. Thickness 4mm 304L stainless steel or equivalent in other material of similar strength Total No. of rings Sufficient to comply with tank design. Cradle Supports 304 stainless steel. 304 stainless steel All Fittings to be RJT. Size as per design / customer requirement. All external pipework connections to have the ability to have security tags fitted. 304L Stainless steel. Size of box Size to suit. Lids One Lid or Two split lids hinged and lockable dependant on the size of manway with the ability to have security tag fitted. Drains 2 No. 1" with plastic extension below chassis level. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
4 10 Top Manway 304L Stainless steel non-pressure Neck-ring Profiled centre top. Size of Man-way 300mm or 500mm Round. Must allow for maximum visibility and access of internal areas Position of the tank. Seal Hygienic Food Grade Seal. Easy clean. (sweet white rubber). No of fasteners. Dependent on type of lid fitted. Security. All Man-way's to have means of security tag fitting from the ground. 11 Rear Cabinet As per customers requirement. Finish As per customers requirement. Type Special features As per customers requirement but must have rear doors with the ability to have security tag fitted from the ground. Switchable interior lamp provided. Ability to house sample box as per customer requirements. 12 Side Cabinet As per customers requirement. Finish As per customers requirement. 13 Low level Man-way Type As per customers requirement but must have rear doors with the ability to have security tag fitting. Special features Switchable interior lamp provided. 304L Stainless Steel. No of fasteners Dependent on type of lid fitted. Oval or 500mm Round. Size of Man-way 20" x 16. Oval or 500mm Round. Position Must allow for maximum visibility and access of internal areas of the tank. Sample valve Stainless steel, manually operated fitted to Man-way that must be able to provide a full load sample. Seal Security Jumper hose provided to CIP line for cleaning. Must be designed with no water traps in the pipe work to ensure complete drainage of pipe work and sample valve. Must allow for proper cleaning during CIP process. Hygienic Food Grade Seal. Easy clean. (EPDM seal) not sweet white wrap round seal. All Man-way's to have means of security tag fitting from the ground. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
5 14 Low level Man-way 15 Breather Line. Rear Fitting Only 304L Stainless Steel. Rear Dome. No of fasteners Dependent on type of lid fitted. Oval or 500mm Round. Size of Man-way 20" x 16. Oval or 500mm Round. Sample valve Stainless steel manually operated fitted to Man-way that must be able to provide a full load sample Jumper hose provided to CIP line for cleaning. Must be designed with no water traps in the pipe work to ensure complete drainage of pipe work and sample valve. Position Must allow for maximum visibility and access of internal areas of the tank. Seal Hygienic Food Grade Seal. Easy clean. (EDPM seal) not sweet white wrap round seal Security All Man-way's to have means of security tag fitting from the ground. Note: this configuration significantly reduces the ability to carry out any visual inspection of the front compartment. 304L Stainless Steel. Diameter Suitable size to suit pumped flow rates including unload. Number of None. Breather line fitted with 2" RJT blank cap on the inside of Valves. Manway lid. Type 2" pneumatic operated from the ground. Pipe work. Size to suit the flow rate from flash vacuum pad neck, taken down and terminating at bearer level, pointing downwards with an open end. Foot and Mouth Provision to be provided for future fitting of Foot and Mouth Filter. Filter. 16 Mountings As per customer requirements. Type As per customer requirements. Securing Points. To suit manufacturer s requirements. Finish Descaled. 17 Vacuum Line 304L Stainless Steel. Diameter 1.5" minimum requirement. No of Valves. 2 Type of Valve 1 No. 1.5" pneumatically actuated butterfly valve at low level adjacent to exhauster isolating valve when over spill occurs and on CIP. 20mm ball valve and 20mm hose tail adjacent to the exhauster Wash Connection. isolating valve on exhauster side. Pipework. 2" pipework taken down near side from manway of tank into AEV top valve. All pipework connection to have the ability to have security tag fitting. AEV Pipework T connection off vacuum horizontal line fitted with 2" pipework and connected to probe chamber, out let side of probe chamber taken to D140 via exhauster isolation valve. Two over spill probes fitted, one in vertical vacuum line at high level and one in probe chamber both interconnected to control box in cab. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
6 18 CIP 304L Stainless Steel. No of spray Suitable number of spray balls or spinners to provide a suitable balls/spinners. CIP. Manifold. Each transpray manifold with 2" pipework to customer specifications. No of Valves. 1. Valve Description. 2" pneumatically actuated butterfly valve. Security All pipework connections to have the ability to have security tag fitting. 19 Outlet pipe 304L Stainless Steel. Diameter 3" connection. No of Connections. 1 Type of Connections. Slipper type. Position. Bottom rear of tank into rear cabinet.2 20 Side access ladder 21 Manway Access Platform. Fast Dump 3" fitted between outlet and sump box. If required. Stainless Steel or Aluminium above nearside side-guard fixed to spill box. Signage stating, No Access - Authorised personnel only." to be placed at foot of ladders. Quantity 1No Finish Polished or powder coated. Handrail. Aluminium grating profiled to front dome and supported on stainless steel brackets.304l Stainless steel Aluminium tubular covering two sides of the platform, open for access from the ladder. Position. On front dome. 22 Ladder. Aluminium tube. Position. Nearside or Offside of platform determined by position of manway lid and chassis / cab equipment. 23 Hose Storage 304 stainless steel, aluminium or material of comparable strength. 1 no Size as per Tank Manufactures design. Position as per requirement to tank design. 24 Hose Make Food grade. Length as per customers requirement. Hose End Filter and Blanking Cap. Size as per customer requirements. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
7 25 Sample Cabinet 26 Compressor / Exhauster 27 Hydraulic Drive 28 Certification 29 Cladding Stainless Steel. 30 Cladding GRP 31 Type of insulation Type Compressor / Exhauster. Foot and Mouth point. Hydraulic Drive Hydraulic Test & Certification 304L Stainless Steel. Stainless steel cabinet with lift up door, mounted at rear off side large enough to accept sample box with means of security tag fitting. As per customers requirement. Suggested D140. Provision to be made for the fitting of Foot and Mouth Filter. As per customers requirement. Suggested suitable drive system with solenoid stop / start control fitted with Handbrake interlock. As Per customers requirement. 0.7mm 304 stainless steel External finish As per customers requirement. Special features Sheets overlapped, bands at front & rear dome. Panel behind ladder relieved to give 200mm Toe -clearance minimum. Glass Reinforced Plastic External finish White impregnated or coloured to suit customers requirement Special features Thickness of insulation Sheets overlapped and sealed. Panel behind ladder relieved to give 200mm Toe -clearance minimum. Polystyrene on tank, fibreglass on domes. Sufficient to ensure temperature does not increase any more than half a degree in 24hrs as per BS 3441 (1995). 32 GRP Domes White impregnated or coloured to suit customer requirements. 33 Sealing Points. All lid and door locking points to incorporate holes to accept appropriate sealing tags that can be carried out at ground level. 34 Side-guards Sufficient to Whole Vehicle Type approval. No of Rails Sufficient to comply with Whole Vehicle Type approval. 35 Mudguards Spray suppression. 36 Lighting All lighting to conform to Whole Vehicle Type approval. 37 Rear Bumper Must conform to Whole Vehicle Type approval. 38 Thermometer Requirement. 39 Hub odometers. Requirement. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
8 40 Reverse Alarm. Audible Reverse alarm fitted 41 Painting Mild steel parts Paint make option. Grade option. Colours Your fleet colour. 42 Extras Spanners supplied should be suitable for the pipework fitted. 43 Data Capture CIP Document Holder Type As Per customers requirement and design. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
9 2. ATMOSPHERIC PUMP LOADING / DISCHARGE RIGID / ARTICULATED MILK COLLECTION TANKER Code of Practice 1 Capacity As per customers requirement +/- 1% ullage. 2 Test Pressure 5psi Hydraulic test pressure. Working pressure Atmospheric. 3 General To operate at customers requirement. Dimensions Length as per current Road use Regulations. Height as per Requirement but must be within current Road use Regulations. Height as per Requirement but must be within current Road Use Regulations. Slope to Rear 1.5º. 4 Barrel Full Material 304 stainless steel or other Food Grade steel of comparable strength. Thickness 3mm. Barrel type As per customers requirement. Internal finish Welds ground and polished to 2B surface finish as per BS Baffle 6 Dished Ends 7 Pipe Work and Connections. 304 stainless steel or other Food Grade steel of comparable strength. Thickness 3mm minimum. No of baffles 1 No. (Preferred ). Baffle features Adequate cut out for access to both compartments. Bottom cut out for drainage. Side Drain Holes 3 & 9 o clock 3mm 304L stainless steel or other Food Grade steel of Cleaning Rings comparable strength with top and bottom 3/4" test sockets, PVC bottom catch tube 304 stainless steel or other Food Grade steel of comparable strength. Thickness 3mm 304 stainless steel All Fittings to be RJT. Size as per design / customer requirement. All external pipework connections to have the ability to have security tags fitted. 8 Milk Pump. 304 stainless steel Type As per customers requirement. 9 Pressure / Vacuum Relief 10 Spill Box No. of relief 1 No. Flash-Vacuum vent valve. valves 1 x 2.5" pressure relief valve fitted to Man Lid. 304L Stainless steel. Size of box Suitable size to gain access. Lids One Lid or Two split lids hinged and dependant on the size of manway with the ability to have security tag fitting. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
10 11 Top Manway 304L Stainless steel non-pressure Neck-ring Profiled centre top. Size of Man-way 300mm or 500mm Round. Position Must allow for maximum visibility and access of internal areas of the tank. Seal Hygienic Food Grade Seal. Easy clean. (sweet white rubber). Not wrap round type. No of fasteners Dependent on type of lid fitted. Top vent 2" pneumatic activated vent operated from ground level. 12 Rear Cabinet As per customers requirement. Finish As per customers requirement. Type As per customers requirement but must have rear doors with means of security tag fitting from the ground. Special features Switchable interior lamp provided. 13 Side Cabinet As per customers requirement. Finish As per customers requirement. Type As per customers requirement but must have rear doors with means of security tag fitting from the ground. Special features Switchable interior lamp provided. 14 Low level Man-way 304L Stainless Steel. No of fasteners Dependent on type of lid fitted. Oval or 500mm Round. Size of Man-way 20" x 16. Oval or 500mm Round. Position Must allow for maximum visibility and access of internal areas of the tank. Sample valve Stainless steel, manually operated fitted to Man-way that must be able to provide a full load sample Jumper hose provided to CIP line for cleaning. Must be designed with no water traps in the pipe work to ensure drainage of pipe work and sample valve. Must allow for proper cleaning during CIP process. Seal Hygienic Food Grade Seal. Easy clean. (EPDM seal). Not sweet white wrap round seal. Top vent 2" Pneumatically operated valve to top neck, sprung-open, closes with roller switch to rear door. Security All Man-way's to have means of security tag fitting from the ground. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
11 15 Low level Man-way Rear Fitting Only 304L Stainless Steel. Rear Dome. No of fasteners Dependent on type of lid fitted. Oval or 500mm Round. Size of Man-way 20" x 16. Oval or 500mm Round. Sample valve Stainless steel manually operated fitted to Man-way that must be able to provide a full load sample. Jumper hose provided to CIP line for cleaning. Must be designed with no water traps in the pipe work to ensure drainage of pipe work and sample valve.. Position Must allow for maximum visibility and access of internal areas of the tank. Seal Hygienic Food Grade Seal. Easy clean. (EPDM seal) Not sweet white wrap round seal. Top vent 2" Pneumatically operated valve to top neck, sprung-open, closes with roller switch to rear door. Rear Cabinet S/Steel or GRP cabinet containing low man-lid, outlet and CIP inlet, lockable. Note: this configuration significantly reduces the ability to carry out any visual inspection of the front compartment 16 Low level Man-way 1x 150mm diameter flash vacuum vent set to 1"hg. Positioned Fitted with 14 & Pressure / in raised pad on centre-line tank top at mid position and 2 1/2" 15 above. Vacuum Relief twin act relief valve incorporated into neck. Valve. 17 Breather Fitted with 14 & Line. 15 above. Stainless steel. Diameter 2". Number of 1. Valves. Type 2" Pneumatically operated from the ground. Pipe work. Size to suit the flow rate from flash vacuum pad neck, taken down and terminating at bearer level, pointing downwards with 18 Mountings 19 Stiffening Rings Foot and Mouth Filter. an open end. Provision to be provided for future fitting of Foot and Mouth Filter. As per customer requirements. Type As per customer requirements. Securing Points. To suit manufacturers requirements. Finish Descaled. 304L stainless steel or equivalent in other material of similar strength. Total No. of rings Sufficient to comply with tank design. Cradle Supports 304 stainless steel. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
12 20 CIP Yes 304 stainless steel Type Permanently fixed spray balls (removable by "C" clips) or spinners. No. of spray Suitable number of spray balls or spinners to provide a suitable balls/spinners CIP Diameter 2 pipe reduced to spray-balls. Fitting 2 x 2 RJT male connections fitted centrally to top of tank. All pipework connections to have the ability to security tag fitted. 21 Side access ladder 22 AEV Breather Line Inlet location CIP Flow Rate & Required Pressure. In rear cabinet. Valve is 2 manual RJT male/male thread with blank cap and chain. Flow Rate and required pressure to be indicated next to CIP inlet connection. If required. Stainless Steel or Aluminium above nearside side-guard fixed to spill box. Signage stating, No Access - Authorised personnel only." to be placed at foot of ladders. Quantity 1No Finish Polished or powder coated. 304L Stainless steel Position. On top of AEV as per manufactures design. 23 Hose Storage If required. 304 stainless steel or aluminium. 1No Size as per Tank Manufactures design. Position as per requirement to tank design. 24 Hose Make Food grade. Length as per customers requirement. Hose End Filter and Blanking Cap. Size as per customer requirements. 25 Cladding Stainless Steel. 0.7mm 304 stainless steel External finish As per customers requirement. Sheets overlapped, bands at front & rear dome. Special features Panel behind ladder relieved to give 200mm Toe -clearance minimum. 26 Cladding GRP Glass Reinforced Plastic External finish White impregnated or coloured to suit customers requirement Sheets overlapped and sealed. Special features Panel behind ladder relieved to give 200mm Toe -clearance minimum. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
13 27 Type of insulation Thickness of insulation Polystyrene on tank, fibreglass on domes. Sufficient to ensure temperature does not increase any more than half a degree in 24hrs as per BS 3441 (1995). 28 GRP Domes White impregnated or coloured to suit customer requirements. 29 Sealing All lid and door locking points to incorporate holes to accept Points. appropriate sealing tags that can be carried out at ground level. 30 Side-guards As per customers requirement. No of Rails Sufficient to comply with current Whole Vehicle Type Approval. 31 Mudguards Spray suppression to comply with current legislation. 32 Lighting All lighting to comply with current Whole Vehicle Type Approval. 33 Rear Bumper Must conform to comply with current Whole Vehicle Type Approval. 34 Thermometer Requirement. 35 Hub Requirement. odometers. 36 Reverse Audible Reverse alarm fitted Alarm. 37 Painting Mild steel parts Paint make option. Grade option. Colours Your fleet colour. 38 Extras Spanners supplied should be suitable for the pipework fitted. 39 Data Capture System. 40 Sample Box Cabinet. CIP Document Holder Type As Per customers requirement and design. Provision to be made to include a Sample Box storage shelf or Cabinet to hold the standard size sample box and have the ability to security tag fitted. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
14 3. APPROVED RELOAD / BULK TANKER Code of Practice 1 Capacity 30,000-litres +/- 1% ullage. Removed 38,000 Capable of operating at 44 tonne GVW. 2 Test Pressure 5psi Hydraulic test pressure. Working pressure Atmospheric. 3 Tare Weight Target Weight of 5.8 tonnes. Length as per current Road use Regulations. Height as per Requirement but must be within current Road use Regulations. 4 Barrel 5 Baffle 6 Dished Ends 7 Top Manway Full Material 304 stainless steel or other Food Grade steel of comparable strength. Thickness 2.5mm. Barrel type Preferred Straight cylindrical Internal finish Welds ground and polished to 2B surface finish as per BS stainless steel or other Food Grade steel of comparable strength. Thickness 3mm No of baffles 1 No. (Preferred ). Baffle features Adequate cut out for access to both compartments. Bottom cut out for drainage. Side Drain 3 & 9 o clock Holes 3mm 304L stainless steel or other Food Grade steel of Cleaning Rings comparable strength with top and bottom 3/4 test sockets, PVC bottom catch tube 304 stainless steel or other Food Grade steel of comparable strength. Thickness 3mm 304L Stainless steel non-pressure Neck-ring Profiled centre top. Size of Manway 300mm or 500mm Round. Pressure Relief 3mm stainless steel pressure relief valve Valve Position Must allow for maximum visibility and access of internal areas of the tank. Seal Hygienic Food Grade Seal. Easy clean. (sweet white rubber). No of fasteners Dependent on type of lid fitted. 8 Pressure / Vacuum Relief No. of relief valves 1 No. Flash-Vacuum vent valve. 1 x 2.5" pressure relief valve fitted to Man Lid. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
15 9 Spill Box 10 Low level Man-way 304L Stainless steel. Size of box 800mm x 800mm Lids One Lid or Two split lids hinged and dependant on the size of manway with security tag fitting from the ground. 304L Stainless Steel. No of fasteners Dependent on type of lid fitted. Oval or 500mm Round. Size of Manway 20" x 16. Oval or 500mm Round. Position Must allow for maximum visibility and access of internal areas of the tank. Sample valve Stainless steel, manually operated fitted to Man-way. Must be designed with no water traps in the pipe work to ensure complete drainage of pipe work and sample valve. Jumper hose provided to CIP line for cleaning. Must allow for proper cleaning during CIP process. Seal Hygienic Food Grade Seal. Easy clean. (EDPM seal). Top vent 2" Manually operated valve to top neck, operated from ground level. Security All Man-way's to have means of security tag fitting from the ground. 11 Low level Man-way Rear Fitting Only 304L Stainless Steel. Rear Dome. No of fasteners Dependent on type of lid fitted. Oval or 500mm Round. Size of Manway 20" x 16. Oval or 500mm Round. Sample valve Stainless steel manually operated that provides a full load sample direct from the barrel. Jumper hose provided to CIP line for cleaning. Position Must allow for maximum visibility and access of internal areas of the tank. Seal Hygienic Food Grade Seal. Easy clean. (EPDM seal). Not sweet white wrap round. Top vent 2" Manually operated valve to top neck, sprung-open, closes with roller switch to rear door. Rear Cabinet S/Steel or GRP cabinet containing low man-lid, outlet and CIP inlet. Note: this configuration significantly reduces the ability to carry out any visual inspection of the front compartment 12 Low level Man-way Pressure / Vacuum Relief Valve. Fitted with 10 & 11 above. 1x 150mm diameter flash vacuum vent set to 1"hg. Positioned in raised pad on centre-line tank top at mid position and 2 1/2" twin act relief valve incorporated into neck. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
16 13 Breather Line. Fitted with 10 & 11 above. Stainless steel. 14 Spill Box 15 Stiffening Rings Diameter 2". Number of 1. Valves. Type 2" Pneumatically operated from the ground. Pipe work. 2" from flash vacuum pad neck, taken down and terminating at bearer level, pointing downwards with an open end. Foot and Mouth Provision to be provided for future fitting of Foot and Mouth Filter. Filter. 304L Stainless steel. Size of box Sized to accept Flash Vacuum Valve vent pad, breather line valve and pressure relief valve. Rain Drain. Single 2" rain drain. Lids Two split lids hinged and the ability to fit a security tag from the ground. 304L stainless steel or other Food Grade steel of comparable strength. Total No. of Sufficient to comply with tank design. rings Cradle Supports 304 stainless steel. 16 CIP Yes 304 stainless steel Type Permanently fixed spray balls or spinners (removable by "C" clip fixing). No. of spray Suitable number of spray balls or spinners to provide a balls/spinners suitable CIP. Diameter 2 pipe reduced to spray-balls. Fitting 2 x 2 RJT male connections fitted centrally to top of tank. All pipework connections to have the ability to security tag fitted. Inlet location In rear cabinet. Valve is 2 manual RJT male/male thread with blank cap and chain. 17 External Foot Valve CIP Flow Rate & Required Pressure. Flow Rate and required pressure to be indicated next to CIP inlet connection. 304L Stainless steel Diameter 3 No of valves One Make 3 RJT Model 3 butterfly c/w locking handle Special features Operating handle extended to rear or side cabinet. Method of Manual operation Outlet Pipe 3" outlet pipe taken from foot valve and terminated in rear work. cabinet with external outlet valve. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
17 18 External valves 304L Stainless steel. No of valves One Model 3 butterfly Special features Terminate inside cabinet. Method of Manual operation Diameter 3 RJT male thread and 3" Blanking Cap. Reducer Fitted with a 3 /2.5 or 3"/2" adaptor and terminating in a 2.5" or 2" blank cap c/w s/s chain as per customer requirement. 19 Trestle Optional preference. support 20 Rims Material Optional Size Optional Finish Optional Dish Optional 21 Tyres Size Optional Make Optional Model Optional 22 Running Gear 23 Running gear sub frame 24 Ladder Bar 25 Side access ladder 26 Hose Storage Make Optional Model Air suspension No of axles Three Lift options Optional Steer options Optional Type of brakes Optional ABS Yes Type Optional Load sensing Yes As per customer requirement and tank design. Stainless steel 304 Polished finish Type Ladder fixing point on nearside of top spill box. If required. Stainless Steel or Aluminium of equal strength. above nearside side-guard Quantity 1No Finish Polished or powder coated. If required. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
18 27a Cladding Stainless Steel. 27b Cladding GRP. 28 Type of insulation 29 GRP Domes 30 Sealing Points. 31 Sideguards 32 Landing legs 33 Rubbing Plate 0.7mm 304 stainless steel External finish Optional. Sheets overlapped, bands at front & rear dome. Special features Panel behind ladder relieved to give 200mm Toe -clearance minimum. Glass Reinforced Plastic External finish White impregnated or coloured to suit customers requirement Sheets overlapped and sealed. Special features Panel behind ladder relieved to give 200mm Toe -clearance minimum. Thickness of insulation Polystyrene on tank, fibreglass on domes. Sufficient to ensure temperature does not increase any more than half a degree in 24hrs as per BS 3441 (1995). White impregnated or coloured to suit customer requirements. All lid and door locking points to incorporate holes to accept appropriate sealing tags which can be fitted from the ground. As per customers requirement. No of Rails Sufficient to comply with Whole Vehicle Type approval. Mild steel Speed Two speed Type of landing s specification. leg Feet type s specification. Heavy duty mild steel King pin s specification. Weld or bolt in s specification. Make s specification. Diameter 2 Kingpin 34 Mudguards Spray suppression to meet current legislation. Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
19 35 Lighting 36 Rear Bumper 37 Thermometer 38 Hub odometer. 39 External Brake. 40 Reverse Alarm. All lighting to conform to current Whole Vehicle Type approval. Must conform to current Whole Vehicle Type Approval. Requirement. Requirement. To meet Whole Vehicle Type Approval. Audible Reverse alarm to meet Whole Vehicle Type Approval. 41 Lubrication. Auto-lube fitted to steer axle and lift axle grease points if fitted. 42 Shipping Hooks 43 Painting Mild steel parts Stainless steel / Mild Steel. Paint make option. Grade option. Colours specified. 44 Extras Spanners supplied to suit pipework fitted. CIP Document Holder Dairy UK DTAS Codes of Practice on Milk Tanker Design Version 3 as at April
ADR/Chemical Tanker Specification
ADR/Chemical Tanker Specification CRT001X 18T 32T Operation 1 Capacity 2 Tare Weight (Approximate) 3 Dimensions (Approximate) ADR/Chemical Rigid Tanker Capacity, Tare weight and Dimensions will vary dependent
More informationSpecification Sheet Doc Rev
Quote Name: Name Shop Order Number: Sales Administration Use Only Number-001 Serial Number/s: Number Date: xx/xx/xxxx CUSTOMER : Customer Name SALESPERSON : Salesperson Name MODEL : 1611 Cu. Ft. Super
More informationSpecification Sheet Form Rev
Sales Administration Use Only Customer Quote Number Quote Revision Shop Order Number Serial Number(s) Date : Customer Name Salesperson Model : Salesperson Name : 8400 DDC S1 Part / Drawing Number : 730-8400
More informationSpecification Sheet Doc Rev. 12/15/95
Specification Sheet Doc Rev. 12/15/95 Date: 24 April 1997 MODEL 2000 x 4 ALUMINUM VACUUM PNEUMATIC DRY BULK DRAWING NO Spec. No. 2061 A. VESSEL 1. Capacity 2000 Cubic Feet - Four 45-degree hoppers - 102"
More information2. Compartments 2 compartments with gallons front to rear with double bulkheads
January 10, 2016 STE # 11602 & 11605 (Ref. QT 3098/STE#10741-10744) ST&E SPECIFICATIONS FOR 4,000 US GALLON DOT-407 DOUBLE CONICAL STAINLESS STEEL INSULATED TWO COMPARTMENT TANDEM TRANSPORT TANK PREPARED
More informationSpecification Sheet Doc Rev
Quote Name: Name Shop Order Number: Sales Administration Use Only Number-001 Serial Number/s: Number Date: xx/xx/xxxx CUSTOMER : Customer Name SALESPERSON : Salesperson Name MODEL : 1625 Cu. Ft. Model
More informationSpecification Sheet Doc Rev
Quote Name: Name Shop Order Number: Sales Administration Use Only Number-001 Serial Number/s: Number Date: xx/xx/xxxx CUSTOMER : Customer Name SALESPERSON : Salesperson Name MODEL : J&L 1850 Model Vacuum/Pneumatic
More informationTROXELL COMPANY, INC E. HWY. 114 RHOME, TEXAS 76078
GENERAL CONSTRUCTION TROXELL COMPANY, INC. Specification Sheet 9250GL (220bbl) DOT407, Aluminum, Double Conical, Single Compartment, Tandem Axle Crude, Oil Tank Trailer MODEL: TRX407AL-220-1-DC-2-P NV-1407
More informationSpecification Sheet Doc Rev
Quote Name Name Shop Order Number Sales Administration Use Only Number-001 Serial Number/s Number Date xx/xx/xxxx CUSTOMER Customer Name SALESPERSON Salesperson Name MODEL Super Sander TM, Pneumatic -
More informationSpecification Sheet Form Rev
10000 CDC S1 Sales Administration Use Only Quote Number Quote Revision Shop Order Number Serial Number(s) Date CUSTOMER SALESPERSON MODEL : Customer Name : Salesperson Name : 10000 CDC S1 PART NO./DRAWING
More informationKRONE - Profi Liner. Quantity: 2 Type: SDP 27 elp3-cs. Technical specification/description
KRONE - Profi Liner Quantity: 2 Type: SDP 27 elp3-cs Technical specification/description FIN-registration (Finland) Without country symbol sticker Lettering on manufacturers plate: Type: SD National type
More informationDry Bulk Super Sander Trailer Specification Sheet
Quote Name: Name Shop Order Number: Sales Administration Use Only 417464-001 Serial Number/s: 700287-700346 Date: Date: xx/xx/xxxx CUSTOMER : Olsta/PneuTech Stock SALESPERSON : MODEL : Super Sander TM,
More informationSpecification Sheet Doc Rev
Quote Name: Name Shop Order Number: Sales Administration Use Only Number-001 Serial Number/s: Number Date: xx/xx/xxxx CUSTOMER : Customer Name SALESPERSON : Salesperson Name MODEL : 1240 Cu. Ft. Super
More information26000 litre ISOTANK SPECIFICATION FOR HAZARDOUS CHEMICALS TRANSPORT AND STORAGE SPECIFICATION T11.
26000 litre ISOTANK SPECIFICATION FOR HAZARDOUS CHEMICALS TRANSPORT AND STORAGE SPECIFICATION T11. DESCRIPTION: 26 000 LITRE INSULATED UN PORTABLE TANK, TYPE T11 For transport of product classes 3, 4,
More informationINDUSTRIAL SERVICE TANKS
INDUSTRIAL SERVICE TANKS Glendale Service s are designed and built with you in mind. We ensure every PWT and VST Series tank is tailored to load quickly and efficiently. Over 25 years of experience, certified
More information2014 HEIL DOT407AL 9240GL, DOUBLE CONICAL, TANDEM AXLE, CRUDE OIL TRANSPORT WITH PUMP & CENTRIFUGE NV1309 VIN: 5HTDL4527D7H45530
2014 HEIL DOT407AL 9240GL, DOUBLE CONICAL, TANDEM AXLE, CRUDE OIL TRANSPORT WITH PUMP & CENTRIFUGE NV1309 VIN: 5HTDL4527D7H45530 VESSEL 1) Design Two piece barrel, 5454-H32 aluminum alloy for shell. 5454-0
More informationA vehicle constructed so that it can be unloaded by part of the vehicle being tipped side-ways or rearwards.
Form Number: DVT 847 Issue: 5 Origin: DVT Review: 1 Jan 2015 SIDEGUARD, REAR UNDER-RUN DEVICE AND BUMPER BARS APPLICATION SIDEGUARDS Goods Vehicles first used from 1 April 1984 with a maximum gross weight
More informationSpecification Sheet Form Rev
Quote Name: 8500 EDC S1 Shop Order Number: Sales Administration Use Only Number-001 Serial Number(s): Number Date: 99/99/9999 CUSTOMER : Customer Name SALESPERSON : Salesperson Name MODEL : 8500 EDC S1,
More informationSpecification Sheet Form Rev
Sales Administration Use Only Quote Name Quote Revision Shop Order Number Serial Number(s) Date Customer : Customer Name Salesperson : Salesperson Name Model : 38000L L23 S1 Hybrid Duty Petroleum Trailer
More informationSpecialists in Aluminium & Steel Tray Bodies. Contents
Specialists in Aluminium & Steel Tray Bodies Duratray Transport Equipment are manufacturers of quality aluminium and steel tray bodies and associated accessories. Duratray have implemented a quality assurance
More informationUnit Number: RDC001 SMU: Date: Feb 2, 2014
MAINTCLF002 CAT 777BCD DUMP TRUCK 500HR SERVICE Unit Number: C001 SMU: 10256 Date: Feb 2, 2014 SAMPLE Initial Engine Transmission Hydraulic / Brakes Steering Front hubs LH (X) RH (X) Differential Final
More informationPLASTIC BIN SUPPORT RACKS
PLASTIC BIN SUPPORT RACKS Louvered bin panels can be wall-mounted, attached to back of shelving, mounted on benches, carts, inside cabinets, fastened to slotted angle components or used for service truck
More informationTECHNICAL SPECIFICATION HD5395TS. HD 5395 TS (Heavy Duty 95tonnes Tridem Steered ) Loaded: Limited at 40 km/h** Unloaded: Limited at 60 km/h*
TECHNICAL SPECIFICATION HD5395TS BASICS Model name Axle driveline configuration Nominal G.V.W. @ 40km/h Nominal target payload @ 40 km/h Category Speed HV 1310.5mm HA 1307.5mm Front axle loads @ 40km/h
More informationTechnical Specification for 1800L Foam Tank Trailer Complete With FJM 100 S Monitor (Part No )
Technical Specification for 1800L Foam Tank Trailer Complete With FJM 100 S Monitor (Part No. 16356) 1) Overview The Foam Trailer assembly consists of the following main components: a) 4 Wheel Trailer.
More informationSPECIFICATION S 42m3 Tridem
SPECIFICATION S 42m3 Tridem Barrel Description Model SCX7 11000-1, High Gross, T316L Stainless Steel, Double Conical, Exterior Ring, DOT 407 Trailer. (For Tri-drive application) * Code BUILT TO TC-407
More information1412 TRAKPACTOR SPECIFICATION
Above photograph features a 1412 Trakpactor fitted the with optional side conveyor and magnet. IMPACT CRUSHER Crusher type: Rotor Width: Rotor Diameter: Feed opening: Crusher frame: Rotor: Blowbars: Impact
More informationWEDICO. `çãéäéíé=háí= q~åâ=péãájqê~áäéêi=çî~ä= Art.-No. 67 polished. Measurements Length 745 mm Width 160 mm Height 250 mm Weight 3.
WEDICO `çãéäéíé=háí= Art.-No. 67 polished Measurements Length 745 mm Width 160 mm Height 250 mm Weight 3.8 kg Chassis and superstructure Assembly Frame made of aluminium section, 2 mm thick; torsion resistant.
More informationI. SCOPE The supply of Water Tanker Trucks (Brand New), LHD, Suitable for Use in extreme climatic and physical conditions in Iraq. LOT 1 WATER TRUCKS
I. SCOPE The supply of Water Tanker Trucks (Brand New), LHD, Suitable for Use in extreme climatic and physical conditions in Iraq. LOT 1 WATER TRUCKS 1 II. TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS
More informationI. SCOPE The supply of Water Tanker Trucks (Brand New), LHD, Suitable for Use in extreme climatic and physical conditions in Iraq.
LOT 1 WATER TRUCKS I. SCOPE The supply of Water Tanker Trucks (Brand New), LHD, Suitable for Use in extreme climatic and physical conditions in Iraq. II. TECHNICAL SPECIFICATIONS ITEM 1: TECHNICAL SPECIFICATIONS
More informationGeneral Equipment Marker Boards. Air Reservoirs. Chassis Components. Content - Section 10. Chassis Components
Content - Section Marker Boards Air Reservoirs.1 Tel: 01474 321954 / Fax: 01474 321988 / e-mail: orders@tube-gear.com UK Marker Boards Marker Boards to BSAU 152 1400mm Type 1 140mm 1 Aluminium 9901 140mm
More informationTANKERS FOR TRANSPORT OF LPG
TANKERS FOR TRANSPORT OF LPG TANKERS FOR TRANSPORT OF LPG Semi-trailer tankers or truck-mounted tanks with the option of complete transfer equipment for LPG transport and supply. Lapesa LPG tanks, with
More informationCustom Vac 822 Hydrovac with the following specifications (Tri Drive Mounted):
822 HYDROVAC Custom Vac 822 Hydrovac with the following specifications (Tri Drive Mounted): DESIGN: Vessel designed and constructed in full compliance with Transport Canada TC 407/412 and CSA B620 09 Debris
More informationT E C H N I C A L S P E C I F I C A T I O N
11340 T E C H N I C A L S P E C I F I C A T I O N TANK BODY for save transportation of diesel and petrol (gasoline) Volume: approx. 16.000 ltr. incl. 3% expansion High Quality Product MADE IN GERMANY 100%
More informationHYGIENIC EQUIPMENT CATALOGUE //
HYGIENIC EQUIPMENT CATALOGUE // 5 The Fort Vale Range of Equipment 2 for Food, Brewery & Hygienic Applications 3 THIS PAGE IS INTENTIONALLY BLANK FOOD, BREWERY & HYGIENIC EQUIPMENT // CONTENTS // TOP MOUNTED
More informationHale Trailer Brake & Wheel Heil
Hale Trailer Brake & Wheel Heil 711061-711070 Model Code Capacity Compartments Shape Shell Material Head Material Operating Pressure Barrel Description APXS 1040-1, Aluminum, Pneumatic dry bulker, Interior
More informationDFID armoured vehicles framework specifications
DFID armoured vehicles framework specifications NOTE: These were the specifications used in our 2011 framework tender, based on our operational requirements at the time. Some of these are no longer current,
More informationNZ Oil Industry Safe Loading Pass Guide Notes. Mounted Tank, Trailer, Semi Trailer and Ancillary
Mounted Tank, Trailer, Semi Trailer and Ancillary 11. External Fire Extinguisher (2.5) 2.5.3 Where two fire extinguishers are fitted to any tank wagon, one is to be Located on the left hand side of the
More informationSpecification Sheet Doc Rev
Page # 1 - Specification Sheet Doc Rev. 10 17 01 Quote Name: Pneumatic Technology 05 12 01 1240 Cube Shop Order Number: Date: 4May2006 CUSTOMER : Pneumatic Technology SALESPERSON : Lonnie Jeffers MODEL
More informationWarning. Document ref: A October 2015
Sentry Door Curtain Installation, Operation & Maintainance Instructions Dunham-Bush Ltd, Downley Road, Havant, Hampshire, P09 2JD Tel. 023 9247 7700 Email. info@dunham-bush.co.uk Document ref: 128-000-001-A
More information428 TRAKPACTOR SPECIFICATION
IMPACT CRUSHER Crusher type: Feed opening: Rotor Width: Rotor Diameter: Crusher frame: Rotor: Blowbars: Impact aprons: Engine pulley: Maximum feed size: Impactor speeds: Lubrication: APPLICATIONS 428 Fixed
More informationTrailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains
Trailer Parts Brake Components Axle Components Suspensions Lights & Electrical Wheels & Tires Loading Ramps Couplers & Safety Chains Trailer Jacks Fenders Dump Trailer Parts Tilt SST Parts Decal Kits Brake
More informationDrum Handling. Drum Transporter and Pouring Stand. Drum Trolley and Pouring Stand. Low Loading Drum Carrier Capacity 250kg.
62 Drum Transporter and Pouring Stand For 210 litre steel drums Capacity 350kg Welded steel construction. Removable 2-position handle Wheels: 2 x 400 mm dia. 2 x 160mm dia. castors, with solid rubber tyres.
More information428 TRAKPACTOR SPECIFICATION
Above photograph features a 428 Trakpactor fitted with the optional side conveyor and magnet IMPACT CRUSHER Crusher type: Feed opening: Rotor Width: Rotor Diameter: Crusher frame: Rotor: Blowbars: Impact
More informationWEDICO. `çãéäéíé=háí= q~êéjqçé=péãájqê~áäéê= Art.-No. 63
WEDICO `çãéäéíé=háí= q~êéjqçé=péãájqê~áäéê= Art.-No. 6 Measurements Chassis and superstructure Finish Assembly Length...768 mm Width...7 mm Height...65 mm Weight...8 kg Frame made of aluminium section,
More informationWorking Height. 9.1m* Basket Floor to ground. 7.1m* Rated Capacity. 180kg. Maximum Reach. 5.8m. Distance to Front Basket. 5.1m. Slew.
NL90ST-HV NL90ST-HV Working Height Basket Floor to ground Rated Capacity Maximum Reach Distance to Front Basket Slew 9.1m* 7.1m* 180kg 5.8m 5.1m 360 continuous Travelling Height 2.8m* * (Depending on truck
More informationHale Trailer Brake & Wheel
Hale Trailer Brake & Wheel 062290 Design Type: FRAMELESS DUMP TRAILER BODY SPECIFICATIONS Genesis Design - INBOARD Length: 32'-0" Width: 96" Overall Side Height: 66" (64"+2") Aluminum Height: 64" Top Rail
More informationRIGID TANKER INSPECTION CHECKLIST
PASS2LOAD INSPECTION P2L label # RIGID TANKER INSPECTION CHECKLIST AIL Location: AIL No: Inspector Name: Rego No: DG No: Vehicle Owner: This checklist must be completed in conjunction with the SLP Operating
More information1. All aircraft fueling equipment shall have a Filter/Separator or a Full-Flow Fuel Monitor.
No. 401 STANDARD SAFETY PROCEDURES STANDARD EQUIPMENT LIST FOR FUELING VEHICLES OBJECTIVE: To ensure the safety of property and personnel, the following minimum operational/equipment list, for each fueling
More informationStandard features. Standard features of the Unimog U500 NA 2005 model
of the Unimog U500 NA 2005 model Engine: - MB 906 diesel engine; 260 hp at 2,200 rpm, torque 700 ft-lbs, max. rpm: 2,500 - Mercedes-Benz 6-cylinder diesel engine water cooled, turbo charger and intercooler
More informationTrailer Parts. Brake Components. Axle Components. Suspensions. Lights & Electrical. Wheels & Tires. Loading Ramps. Couplers & Safety Chains
Trailer Parts Brake Components Axle Components Suspensions Lights & Electrical Wheels & Tires Loading Ramps Couplers & Safety Chains Trailer Jacks Fenders Dump Trailer Parts Tilt SST Parts Decal Kits Brake
More informationADDENDUM 02. To All Bidders:
ADDENDUM 02 Project: 2017 Water Truck Request for Tender Addendum: A-02 Location: 117 7 Avenue SE, Drumheller, Alberta Date: October 11, 2017 To All Bidders: 1. General 1.1. This addendum shall be read
More informationFOR SALE REBORN WHALE. The next journey...is just as important as the first. Demount MVC Body ONLY. Web Ref:0006. Reliability, Service, Value for Life
REBORN WHALE Tanker Manufacturer Vehicle Type Capacity of Tanker Year of Production *Chassis Not Included Model Chassis Manufacturer Axle Configuration Euro Emissions Level Reg No or Year Recorded Mileage
More informationSelf Bunded Storage & Dispensing Solutions for Petroleum Products
Self Bunded Storage & Dispensing Solutions for Petroleum Products www. LIQUITAINER Containerised Self Bunded Tanks - Design Features Roof with curved radius - NO pooling of water Designed and Approved
More informationCode of Practice 305 Caravan Movers
The UK trade body for the caravan, motorhome, caravan holiday and park home industry. Code of Practice 305 Caravan Movers (minor revision) Publication Date: 1 Scope This code of practice specifies the
More informationSPECIFICATIONS FOR MULTIMIXER PZ-CB-MM CONE BOTTOM, CENTER OUTLET
A B C BALDOR 28" PZ-MM-CB HP & RPM HP APPROX CAPACITY A B C SCRAPER HIGH SHIPPING SHEAR WEIGHT * 10 GAL 16 21 14 1@34 3 725 # * 25 GAL 24 29 16 2@30 5 850 # * 50 GAL 28 33 24 3@28 10 1100 # 100 GAL 38
More informationProperty of American Airlines
Date Maintenance Check list The inspection and preventive maintenance schedule of the Power Stow Rollertrack is as follows: Daily (10 hrs), Weekly (50 hrs.), every 6 months ( hrs.), yearly (1 hrs.) and
More informationSandvik TH551 Technical Specification
Spec. number TH551-05 2014-08-14 Technical Specification APPLICATIONS The is a high performance 51 tonne articulated underground dump truck for use in 5 x 5 meter haulage ways. Operator safety, health
More informationA Permanent Pothole Solution
A Permanent Pothole Solution Modern Spray Injection Technology for Potholes, Alligator Cracks, Shoulders and Washouts. Parking Lots, Residential Roads, Highways and Interstates. The Most Cost Efficient,
More information4242SR SPECIFICATION IMPACT CRUSHER APPLICATIONS. Above photograph features a 4242SR fitted with the optional side conveyor and magnet
Above photograph features a 4242SR fitted with the optional side conveyor and magnet IMPACT CRUSHER Crusher type: Feed opening: Rotor Rotor Diameter: Crusher frame: Rotor: Blowbars: Impact aprons: Engine
More informationMAC TRAILER MANUFACTURING, INC C PNEU MAC TIC DRY BULK
MAC TRAILER MANUFACTURING, INC. 1050-C PNEU MAC TIC DRY BULK MIKE JOHNSON SERIAL NO. #VALUE! 2016 Spring Dealer Incentive Program Base Model Trailer 252Q MODEL NO. TN1050APB 8/12/14 LAST REVISED WEIGHT
More informationSECTION 11 INTERMODAL EQUIPMENT
SECTION 11 INTERMODAL EQUIPMENT ROA MANUAL SCHEDULE OF AMENDMENTS SECTION 11 AMENDMENT NUMBER PAGES AMENDED AMENDMENT SUMMARY DATE ISSUED TABLE OF CONTENTS Section Description Page No. 11.1 SCOPE... 11-1
More informationBulk Material. Handling
Bulk Material Handling 1 The Original Belt-in-a-Tube The BeltVeyor is a durable workhorse for any farm grain handling or bulk materials operation. Portable Tubular Belt Conveyor Fragile materials are handled
More informationWEDICO. `çãéäéíé=háí= `çåí~áåéê=péãájqê~áäéê= Art.-No. 64 white
WEDICO `çãéäéíé=háí= Art.-No. 6 white Measurements Chassis and superstructure Finish Assembly Length...78 mm Width...65 mm Height...58 mm Weight...7 kg Frame made of aluminium section, mm thick; torsion
More informationNarrow Aisle Drum Truck. Drum Handling. Three-in-one Drum Carrier. Drum Transporter and Pouring Stand. Drum Handling. Capacity 300kg UDL
41 Narrow Aisle Drum Truck Capacity 300kg UDL For transport and dispensing from 210ltr steel or plastic drums. Overall width of truck is less than a standard 210 ltr drum Use as truck for transporting
More informationJabiru Aircraft Pty. Ltd. Final Inspection Checklist. Engine Compartment
Jabiru Aircraft Pty. Ltd. Final Inspection Checklist Registration No: Aircraft Checklist Pre Ground Test Model: Serial No: Engine Compartment Propeller: Prop Size: 60 x 53 Other:.. Propeller Serial No:
More informationCONE CRUSHER CRUSHER OPTIONS MAXIMUM FEED SIZE
CONE CRUSHER Crusher type: Liners: Standard concave: Adjustment: Control: Concave options: Eccentric option: 1000 Automax Crusher fitted with long throw eccentric. Manganese steel alloy mantle and concave.
More informationWRANGLER 2016 WHEEL DRIVE, PAD ASSIST & ELECTRIC MODELS
WRANGLER 2016 WHEEL DRIVE, PAD ASSIST & ELECTRIC MODELS BRUSH LIFT 101 9121960 3/8 EXTERNAL STAR LOCK WASHER 1 102 9122030 3/8-16 X 3/4 BUTTON HEAD SOCKET SCREW 1 103 2694261 CABLE 1 104 2391771 90 HOSE
More informationVACUUM TANK LINE PAGE 1 VACUUM TANK LINE AmthorInternational.com
VACUUM TANK LINE PAGE 1 VACUUM TANK LINE 434.656.6233 AmthorInternational.com PAGE 2 TABLE VACUUM OF CONTENTS TANK LINE TABLE OF CONTENTS Page 3 Introduction Page 4 Code Vacuum Tanks Page 6 Non-Code Vacuum
More informationThe figure 269J is a double seal mix-proof piston valve, used for product isolation, where safe separation of process and C.I.P. fluids is required.
The figure 269J is a double seal mix-proof piston valve, used for product isolation, where safe separation of process and C.I.P. fluids is required. Features Product contact parts manufactured from high
More informationACCEPT ONLY THE BEST
ACCEPT ONLY THE BEST Cab & Chassis The truck shall be supplied by the customer. CET Fire Truck Glider kit #7 Revised January 10 th 2018 The glider kit is made for dual rear wheels truck with a «back-of-cab-to
More informationROGERS MACHINERY COMPANY, INC
KOBELCO KNW SERIES Sample Specifications AIR-COOLED, OIL-FREE AIR COMPRESSOR Frame 0, 1, 2 50 500 HP ROGERS 2110_KA.doc Effective: 03-24-17 Supersedes: 04-06-15 Page 1 of 9 1. SPECIFICATIONS SCOPE 1.1
More informationGRP SECTIONAL COLD WATER STORAGE TANKS (STANDARD & L SHAPED)
GRP SECTIONAL COLD WATER STORAGE TANKS (STANDARD & L SHAPED) TABLE OF CONTENTS Introduction... GRP Sectional Water Storage Tanks (Std & L Shaped)... GRP Totally Internally Flanged Tanks (TIF) & Internally
More informationDISAB P 210/ ADR
DISAB P 210/9-1513 ADR P 210/9-1513 ADR shown above is equipped with options. This vacuum loader is designed and built in compliance with applicable ADR regulations and handles material of a consistency
More informationMODELS EAH / EC/E TALL/3-Door Parts Manual Revision 1.04A
MODELS EAH / EC/E TALL/3-Door Parts Manual Revision 1.04A CMA DISHMACHINES 12700 KNOTT STREET GARDEN GROVE, CALIFORNIA 92841 800-854- 6417 FAX 714-895-2141 www.cmadishmachines.com TABLE OF CONTENTS PARTS
More informationTRAILER CATALOGUE MADE FOR AUSTRALIAN AUSTRALIAN CONDITIONS FAMILY BUSINESS ESTABLISHED 1964 WARRANTY UPGRADE TO 5 YEARS
TRAILER CATALOGUE AUSTRALIAN MADE FOR AUSTRALIAN CONDITIONS FAMILY BUSINESS ESTABLISHED 1964 WARRANTY UPGRADE TO 5 YEARS ABOUT US Extensive dealer network Servicing QLD, NSW and NT 5 YEAR WARRANTY 50 YEARS
More informationThe HYMIX P2 Series Transit Mixer
The HYMIX P2 Series Transit Mixer Telephone: 01952 200900 mail@hymix.com @hymixuk www.hymix.com MiXoLoGy 1 Supporting the Modern Concrete Operator The Drum We re always looking to deliver more more from
More informationSandvik TH663 Technical Specification
Spec. number TH663-04 Technical Specification APPLICATIONS The is a high productivity 63 tonne articulated underground dump truck for use in 6 x 6 meter haulage ways. Operator safety, health and comfort
More informationSample Specifications 2110_KA.DOC KOBELCO KNW SERIES 1 OF 10 AIR-COOLED, OIL FREE AIR COMPRESSOR Frame 0, 1, HP
KOBELCO KNW SERIES 1 OF 10 1. SPECIFICATIONS SCOPE 1.1 This specification covers the requirement for supply of a packaged oil-free rotary screw air compressor, Kobelco KNW Series model. 1.2 Any and all
More informationPERFORMANCE SUSPENSION PARTS
PERFORMANCE SUSPENSION PARTS Introduction Air Lift Performance The purpose of this publication is to assist with the installation, maintenance and troubleshooting of this Audi A4 B8 Performance kit. It
More informationPEI/RP Recommended Practices for Installation of Bulk Storage Plants
PEI/RP800-08 Recommended Practices for Installation of Bulk Storage Plants Recommended Practices for Installation of Bulk Storage Plants CONTENTS Foreword...iii. SECTIONS 1. Introduction Page 1.1 Background...1
More informationT E C H N I C A L S P E C I F I C A T I O N
11547 T E C H N I C A L S P E C I F I C A T I O N 3-AXLE HEAVY-DUTY LOW-BED SEMITRAILER Custom-made in Germany Type: 8096-BPW Payload: approx. 80 ton Heavy duty off-road low bed semi-trailer for the safe
More informationSpecification Sheet Form Rev
Sales Administration Use Only Quote Name Quote Revision Shop Order Number Serial Number(s) Date Customer : Customer Name Salesperson Model : Salesperson Name Part / Drawing Number : 725-1021 : ST 9300
More informationFuel and Oil Separators
Fuel and Oil Separators PREMIERTECHAQUA.CO.UK Premier Tech Aqua UK s range of Conder Fuel and Oil Separators are for use with surface water drainage systems and are designed to prevent hydrocarbons (e.g.
More information05-08 GT. Hellion Power Systems Mustang Kit Instructions
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
More informationTECHNICAL SPECIFICATIONS FOR BATTERY OPERATED HEAVY DUTY FORK LIFT TRUCK - 20 T
PART B TECHNICAL SPECIFICATIONS FOR BATTERY OPERATED HEAVY DUTY FORK LIFT TRUCK - 20 T 1.0 APPLICATION / PURPOSE : S.No. DESCRIPTION / SPECIFICATIONS 1.1 The proposed Fork Lift Truck is meant to be employed
More informationChassis and Body Specifications
Motorsport Trailers Ltd Specification Sheet Trailer Model 5600 with Internal Bulkhead Date 05th July 2014 Motorsport Trailers Series Chassis and Body Specifications Description Overall Length (from rear
More informationChassis and Body Specifications
Motorsport Trailers Ltd Specification Sheet Trailer Model 5800 with Internal Bulkhead Date 05th July 2014 Motorsport Trailers Series Description Chassis and Body Specifications 5800 with Internal Bulkhead
More informationFuelEquipment.com FUELLING
Service - Lube - Fuel Trucks Fuelling design & build custom service vehicles built to accomplish requirements of your particular business. These vehicles can include new oils, collect, store & discharge
More informationParts Manual for the Wright Z
Parts Manual for the Wright Z Serial numbers 40581 & Higher Check www.wrightmfg.com for the latest revision Rev 9/2007 Shown with OPTIONAL Grass Collection System 2006 Wright Manufacturing Inc., All Rights
More informationHYDROMODEL-200. Implements and controls hydraulic and electro-hydraulic circuits. Transparent Hydraulics - Electro-hydraulics
HYDROMODEL-200 Transparent Hydraulics - Electro-hydraulics Hydraulic and electro-hydraulic technology at a glance Implements and controls hydraulic and electro-hydraulic circuits www.smctraining.com training@smctraining.com
More informationINTRODUCING THE XA400 SPECIFICATION XA400/206
INTRODUCING THE XA400 SPECIFICATION XA400/206 FEATURES The new Terex Pegson XA400 is the most modern plant of its type and is packed with new user friendly features. The very high performance of this new
More informationPART 8 MACHINERY INSTALLATIONS
PART 8 MACHINERY INSTALLATIONS PART 8 MACHINERY INSTALLATIONS SECTION SUBJECT 8.1 General 8.2 Auxiliary engines 8.3 Stern gear 8.4 Propeller and nozzles 8.5 Rudders 8.6 Steering gear 8.7 Tables 8.7.1
More informationLease Automatic Custody Transfer
Lease Automatic Custody Transfer Angus Manufactured LACT Units Updated 19-Dec-01, Slide 2 LACT Unit Requirements Are used for the automatic unattended measurement of crude oil. Accurately measure the quantity
More informationDRAWING: DRW-4622 ISS:A03
Model No: TT-0S Base / Deck Assembly NB: FOR WIRING SEE DRAWING: WD-0 0 0 0 0 DRAWING: DRW- ISS:A0 /0/0 0 Model No: TT-0S Base / Deck Assembly 0 COMBINED INDUCTION MOTOR POLE 0-0V 0Hz 0 COMBINED INDUCTION
More informationDIN Hygienic Union & Fittings
DIN 11851 Hygienic Union & 11852 Fittings The DIN 11851 union is widely used throughout Europe and the Middle East and incorporates a round slotted nut and D Section seal, as standard. The union is manufactured
More informationLine Body Canopy and Accessories:
ATTACHMENT A Heavy Crew Truck Line Body and Accessories Installation. TMWA provided cab & chassis specifications are provided on last page The Cab & Chassis will be a Freightliner (All Other Items Referenced
More informationANSI Z50.1. Safety Standards
ANSI Z50.1. Safety Standards 5. Dry Ingredient Handling Equipment 5.1 General Requirements 5.1.1 Whenever a dry ingredient handling system is of such size that the beginning of its operation is remote
More informationCODE 10 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF FALLING OBJECT PROTECTIVE STRUCTURES ON AGRICULTURAL AND FORESTRY TRACTORS
CODE 10 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF FALLING OBJECT PROTECTIVE STRUCTURES ON AGRICULTURAL AND FORESTRY TRACTORS 1 TABLE OF CONTENTS INTRODUCTION... 3 1. DEFINITIONS... 3 1.1 Agricultural
More information485 - NC NO/DA DN
485 - NC 285 - NO/DA DN 25-100 The 485/285 diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal geometry of the body optimises fluid dynamic
More informationAIR BRAKE SERVICES TRAILQUIP
TQA-MG01R PLASTIC MUD GUARDS & ACCESSORIES COLOUR TQA-MG01B COLOUR RED BLUE TQA-MG01W COLOUR TQA-MG01BK COLOUR WHITE BLACK TQA-MG02 CHASSIS PIPE Heavy Duty Chrome Built in Reflector TQA-MG03 MUD GUARD
More information