Specification Sheet Form Rev

Transcription

1 Sales Administration Use Only Customer Quote Number Quote Revision Shop Order Number Serial Number(s) Date : Customer Name Salesperson Model : Salesperson Name : 8400 DDC S1 Part / Drawing Number : Customer Furnished Tractor Data Required Weights to Include Driver, Fuel, Tools, Equipment, etc. Enable Track Changes on the Review Tab to identify deviation from the Base Model Specification A. VESSEL 1) Design Two piece barrel, 5454-H32 aluminum alloy for shell aluminum alloy for heads. Double conical with 10" drop to center, 50/50 split 2) Capacity 200 barrels, 8400 U.S. Gallons up to +3% tolerance. 3) Commodity Customer to Specify 4) Internal weld finish Prepared for Heil lining, (Special clean outs required) 5) External weld finish As welded, smoke and discoloration removed 6) Temperature 180 o F 7) Code DOT 407 8) Baffles (4) Four full circle aluminum alloy, sanitary flange welded both sides with 3" drains at 3:00, 9:00 and 12:00 o'clock. Bottom tunnel approximately 6-1/2 x 6-1/2 reinforced at center. Baffles designed to accept interior lining. 9) Interior Lining None 10) Insulation None 11) Jacketing None 12) Heat None Page 1 of 6

2 B. TANK FITTINGS AND PIPING 1) Thermometer None 2) Vent (1) One 4" Girard combination vent with Tef-O-Sil gasket 25# MAWP / 4 Hg Vacuum with pressure gauge & spring return ball valve for emergency pressure relief. Location: Inside of spill dam on opposite side of ladder 3) Magnetic Vacuum Breaker Included in Combination vent 4) Vapor recovery 3" Civacon air operated vapor vent in spilldam, actuated with emergency valve operator, 3" line follows curvature of tank. (3) Vapor outlets (1) c/s (1) s/s (1) rear, rear approx. 36 behind emergency valve. All points end with NPT threads. 5) Clean outs (4) Four 3" aluminum sumps with blind flanges evenly spaced on top center line of tank, outboard of baffles. (2) Two 3 aluminum sumps with blind flanges at 3 and 9 o clock for roll over. 6) Emergency valve (1) One Betts 6 90 degree aluminum cable over pulley emergency valve facing forward, EV Operator: Cable Operator near streetside landing gear. 7) Piping and valves 4 Schedule 40, aluminum pipe with 4" Sureseal figure 500 butterfly valve with iron body, iron disc and buna seat, located rear of the cross. 4" line landing gear to streetside and curbside. Each side line has 4" Sureseal figure 500 butterfly valve with iron body, iron disc and buna seat with TTMA flanges. Line to landing gear ends in male NPT threads. 8) Product pump None 9) Gasket Material Customer to specify 10) Hose hook None 11) Manhole Heil 20 aluminum full opening with six cam lock hold downs Cover hinged to curbside away from ladder. Location: Near center of tank with hinge pin at front Gasket: Buna gasket 12) Static line Manhole collar to emergency valve 13) Spill dam Located at approximately center of trailer with rollover protection, 1-1/2" black drain hose both sides Page 2 of 6

3 C. ACCESSORIES 1) Ladder Aluminum mounted streetside center, bolted top and bottom 2) Grab handles None 3) Walkway Platform step as transition between ladder and spilldam 4) Fenders Aluminum single contour, straight front for front fenders, all fender brackets to be bolt on. Aluminum double contour for rear fenders, all fender brackets to be bolt on. 5) Mud flaps Front and Rear, Heil, Anti-sail, Anti-Spray flaps. 6) Cabinet 36 x 18 x 18 aluminum cabinet with lockable door located s/s forward of tandem one door hinged at bottom. 7) Shovel holder Included streetside just in front of tandem 8) Tire carrier None 9) Hose carrier (2) 8 x 21 aluminum hose tubes located (1) curbside (1) streetside doors front only and hinged down. 10) Placard holders Aluminum plates (customer to add placard holders), reachable from ground, front on street side upper quadrant front head, rear located lower quadrant of rear head. Streetside and curbside located on center ring of tank. 11) Document holder Truck-Lite at landing gear frame curbside 12) Sealing provisions None 13) Marker rod None 14) Overfill system Provisions for overfill system including lower bracket in tank. If required, customer to specify readouts units: barrels or gallons Page 3 of 6

4 D. CHASSIS 1) Upper coupler 5/16" heavy duty steel upper coupler with offset pin adjustable in 1-1/2" increments. 2) Landing Legs Jost model A-HEIL magnum 2-speed, sealed gear box with arctic grade grease, 70,000 lbs. rated lift capacity with 10 x 12 sand shoes and streetside crank. 3) Landing Legs Finish Powder coat gray finish for improved durability. 4) Suspension Hendrickson AAT 25K air ride suspension & brake system, 71.5" track axle, parallel spindle, 25,000 lb. beam rating, 49" spacing, with single leveling valve 5) Suspension Finish Suspension Towers painted DuPont Imron Gray Integrated axle painted DuPont Imron Gray 6) Suspension Frame Carbon Steel, Galvanized, Huck-Bolt Bumper: Carbon Steel DOT compliance bumper per FMVSS223 (RIG) Underride: Carbon Steel: Underride is typically not required per wheels back exemption; however, one will be added if required by suspension location. 7) Tow hook Installed on rear bumper 8) Brake System ECU: Wabco 4S/2M ABS system with amber light located in compliance with DOT regulations. No diagnostic plug Configuration: 16.5in x 7in (quick change) S-cam type drum brake system Glad Hands Philips Quick Release gladhand on service line. Constant Power Auxiliary, blue circuit, center pin of SAE J560 7-way. 9) Brake Chamber OEM type parking-emergency spring brake 10) Brake Lining OEM brake lining 11) Slack Adjuster OEM slack adjuster 12) Drums (4) Cast - outboard mount brake drums 13) Axles (2) Integral with air ride 14) Paint Unless otherwise specified, steel parts will be painted DuPont Imron 5000 series gray Page 4 of 6

5 E. WHEEL END 1) Warranty Heil s R2R warranty package which includes Hendrickson s three-year wheel end warranty 2) Hubs (4) Ductile Iron, 10 Stud, hub pilot (single nut mount) hub for outboard drum 3) Lubrication 75W-90 oil 4) Oil Seals OEM 5) Dust shields None 6) Hubodometer None F. WHEELS 1) Wheels See options G. TIRES 1) Tires See options Spare tire None Page 5 of 6

6 H. MISCELLANEOUS 1) Air & electrical Nose box Center of front head with circuit breakers, (1) J560 7-way and (1) ISO way plugs. Lights Truck Lite LED flange mount complying with FMVSS and CMVSS minimum requirements Wiring Truck-Lite FMVSS Harness system. Other lights may require Junction Box Other lights Additional rear stop light LED sequential directional arrows located s/s & c/s rear of front fenders 2) Conspicuity sides of trailer Per FMVSS requirements at approximately 3:00 and 9:00 o'clock continuous on sides 3) Decals Hm-183 test decals Front, streetside on barrel Customer decals None 4) Calibration Increments 1/4in increments, included in documentation Unit of Measure Gallons 5) Documentation Parts and service manual CD is included Texas external visual safety inspection and decal (installed adjacent to data plate) Test paperwork shipped with trailer. 6) Warranty Heil s standard four year warranty - one year bumper to bumper coverage with some areas (e.g., barrel and frame) being extended on a pro-rated basis out as much as 4 years. Heil s value package includes Jost s 5 year maintenance free landing gear warranty. Heil s value package includes Dupont s prorated 3 year warranty on steel parts and prorated 4 year warranty on aluminum parts. Page 6 of 6