Specification Sheet Doc Rev

Transcription

1 Page # 1 - Specification Sheet Doc Rev Quote Name: Pneumatic Technology Cube Shop Order Number: Date: 4May2006 CUSTOMER : Pneumatic Technology SALESPERSON : Lonnie Jeffers MODEL : 1240 Cu. Ft. Super Jet Pneumatic 3 Hoppers (Six Units) PART NO./DRAWING : A FINAL AS PRODUCED SPECIFICATION CUSTOMER FURNISHED TRACTOR DATA REQUIRED WEIGHTS INCLUDE DRIVER AND FUEL TRACTOR DATA : W.B.: 244, Weight: (Fr Axle: 8788 lbs. Rr Axles: 7499 lbs.) : Total Wet Weight 16,287 lbs; 0 to 24 ahead of center sliding fifth wheel; Standard front axle; 379 Conv. Peterbilt Daycab. A. VESSEL 1. Capacity 1240 Cu. Ft. Super Jet Pneumatic 3 Hoppers 2. Tank Construction Smooth exterior, internal rings H32 aluminum vessel Hydro tested at 37.5 P.S.I. 45 degree hopper slope with bolt on spun cones. 3. End Frame Huck riveted bi metal end frames with galvanized hi tensile steel frame rails and aluminum crossmembers, with aluminum struts. Rear frame lengthened 12 from standard of 146 to Interior Welds Class I, as welded. 5. Manholes 3 20 Heil heavy duty cast aluminum manhole covers, pressure type with 6 aluminum cam actuated adjustable hold downs and nylon wear plates. Mount one over each hopper. Aluminum cam handles and nylon wear plates, replaceable wear plates under hold downs, two stainless steel cover retainers per manhole. White neoprene gaskets in manhole covers. Manholes hinge on curbside. 6. Shell Finish Mill finish bulk trailer sheet. 7. Baffles None 8. Documentation Unit tested with water. Professional cleaning is recommended prior to initial loading to avoid possible contamination of cargo. 180 degrees F maximum operating temperature. 9. Product Information Lime (Pebble) 10. Misc. Vessel None

2 Page # 2 - B. TANK FITTINGS AND PIPING 1. Air Inlet Line *Additional 4 air inlet mounted at rear of vessel curbside, ending with check valve, 4 butterfly valve and 4 Male adapter and dust cap (this is to be a separate inlet line forward to a tee at the front inlet, not part of the aeration manifold). *4 aluminum line, 4 manifold, 4 proportioning and check valves with welded 4 adapter streetside front of tank (ILO 3 ) *One (1) Bayco 4 swing spring check valve near P.T.O. inlet. *One (1) Bayco 4 swing spring check valve near #1 hopper valve. 2. Aeration Three (3) SureSeal, SureFlo aerators per hopper. *4 Aluminum air manifold on curbside, 2 hoses supplying air to aeration system. Hopper saver wear plates. * Aeration system includes individual hopper aeration valves, 2 ball valve at manifold, one (1) per hopper. 3. Prop/Pres Ctl Valve *4 Heil fig. 500, aluminum body butterfly valve (alum/bronze disc, white Nitrile seat) proportioning valve. 4. Aeration Valve 3 Heil fig. 500, aluminum body butterfly valve (alum/bronze disc, black Nitrile seat). Locate streetside to regulate airflow to air manifold line. 5. Blow Down Line 3 Sch. 10 aluminum with 3 Heil fig. 500 aluminum body butterfly valve (alum/bronze disc, black Nitrile seat). Locate streetside at front of tank. 25 PSI pressure relief valve. 6. Top Air Line *3 Sch. #10 aluminum top air line with 3 Heil Fig. 500 aluminum body butterfly valve (alum bronze disc, black Nitrile seat). 7. Product Valve *6 Heil Fig. 890 aluminum body, stainless disc, black seat. 8. Product Tee *6 Sch. 40 steel Heil Fabricated wrap around door gravity tee with black gasket and cam lever latch Product Line 4 Sch. 40 aluminum line between hoppers. * Zytel groove to plain clamp joint connector between hoppers, aluminum groove to groove couplers at front & rear. 10. Rear Discharge Sch. 40 aluminum, straight tube, under axle. Welded aluminum male adapter (Part A ) and dust cap at rear of discharge pipe. 11. Vacuum Inlet Line None. 12. Load Line None. 13. Cyclone Filter None.

3 Page # Gauges Two (2) 4 liquid filled, one tank pressure, one line pressure. Gauge pressure range 0 30 PSI. Gauges in cabinet with light located streetside rear, forward of tandem. 15. Miscellaneous None. C. ACCESSORIES 1. Ladder *Aluminum, rear streetside forward of tandem, serrated rungs with grab handles at top step. 2. Hose Tubes 1 * Delete standard hose tube. 3. Walkway * Expanded metal (aluminum) walkway. Wrap with contour of shell and weld on top between manholes. 4. Tire Carrier None. 5. Cabinet None. 6. Hose Holder P.T.O. hose holder at nose. 7. Fenders 2 Aluminum single contour front fenders. 2 Aluminum double contour rear fenders. 8. Splash Guard Anti sail and anti spray for front, dealer furnished flaps Anti sail and anti spray for rear, dealer furnished flaps 9. Lights 12 Volt Truck Lite flange mount LED lamp system comllying to FMVSS with conspicuity markings each side and rear. 2 Combination mid tank clearance and turn signals, one each side. 1 One oval third stop light, located rear center of trailer. Additional clearance lights, LED, includes wiring harness and mounting brackets. Lights are of sealed construction and considered to be watertight. Total of seven (7), each side and (3) three bar lights at rear. 10. Wiring 12 volt system, 7 wire, molded harness throughout. Plug together modular style harness. 7 way SAE J560 connector. 11. Miscellaneous None.

4 Page # 4 - D. CHASSIS 1. Upper Fifth Wheel Hi tensile steel, bolted and adjustable with 2 forged kingpin. 2. Skid Plate None. 3. Landing Legs Holland Binkley square model #51,000, 2 speed, 50,000 lb. with sand shoes, and streetside crank. * Heavy duty landing leg brace kit, includes additional back bracing as well as lateral between legs. 4. Suspension * Hendrickson Intraax inverted axle air ride, parallel axles, & brake system AA230 RC, 71 5 track, 5 round, 5/8 axles, 20,000# beam rating, 49 axle spacing, with single leveling valve. * Automatic dump valve system that exhausts the air from the air bags when the gladhands are disconnected or parking brakes are set. 5. Brake System One (1) aluminum 2850 cu. In. air tank with rubber saddles and stainless steel u bolt mount. System to meet FMVSS requirements. Meritor (Rockwell) Wabco Easy Stop 4S 2M ABS system, (4 sensor/2 modulator). Diagnostic plug not included. Philips Quick Release gladhand on service line. Constant power is standard on auxiliary (blue) center pin of SAE J560 7 way x 7 (quick change) S cam type brake shoes. 6. Brake Chamber OEM type parking emergency spring brake. 7. Brake Lining Non asbestos brake lining. 8. Slack Adjuster Crewson automatic slack adjuster. 9. Axles 2 Integral with air ride. 10. Oil Seals Preset bearing with OEM seals and visible fluid type hubcaps. 11. Paint * Customer to have trailer painted (complete trailer) after delivery. Steel parts only will be primed and painted White. All critical safety and warning decals are to be installed; all non critical decals will be shipped loose. Standard (or optional if specified) non skid will be applied to walkway areas. 12. Misc. Chassis 1 *Hubodometer, Veederoot. Located streetside front.

5 Page # 5 - E. HUBS AND DRUMS 1. Hubs 4 10 Stud, Hub Pilot (single stud mount), aluminum hub for outboard drum (parallel spindle) Standard hub lubrication is CD 50 synthetic transmission fluid. 2. Drums 4 Centrifuse outboard mount brake drums (16.5 x 7 ) F. WHEELS 1. Wheels 4 10 Stud Alcoa Dura Bright Polished aluminum 22.5 x 14.0 (Hub Pilot single nut mount) wheels G. TIRES 1. Tires 4 Michelin Super Single XOne XTE, R Ply L H. MISCELLANEOUS 1. Customer Supplied Parts None. 2. Warranty Standard Silver 4 year limited warranty One year bumper to bumper coverage with some areas (e.g., barrel and frame) being extended on a pro rated basis out as much as 4 years. 3. Other Notes Add Hendrickson Tire Maxx tire inflation system for Intraax suspension tandem