MODEL N COPY OWNER S MANUAL. Keep this Product ID Number and use when contacting Customer Service:

Transcription

1 MODEL N OWNER S MANUAL COPY Keep this Product ID Number and use when contacting Customer Service:

2 REGISTER YOUR PRODUCT ONLINE AT At Lifetime, we are committed to providing innovative and quality products. While registering, you will have the opportunity to give us your feedback. Your input is valuable to us. Lifetime s Promise to You: REGISTER today! Save this owner s manual for future reference and in the event that the manufacturer has to be contacted. Questions or Missing Parts? ID: COPY **U.S. and Canada customers ONLY** DO NOT CONTACT THE STORE! CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) **For Assistance in Europe,** Please contact: Or call: LIFETIME EUROPE After Sales, Euro Base IDA Industrial Estate, Cork Road Waterford, Ireland LEUservices@euro-base.com INSTRUCTION # M 2 2/27/2015

3 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Most injuries are caused by misuse and/or not following instructions. Use caution when using this product. BEFORE BEGINNING ASSEMBLY 3

4 TOOLS AND PARTS REQUIRED FOR THIS ASSEMBLY 1/2 Wrench 11/16 Wrench 9/16 Wrench 3/4 Wrench Electric Drill 1/2 Socket Wrench Rubber Mallet Phillips Screwdriver Scrap Wood Sand Funnel Water Hose Pliers 3/16 Allen Wrench *Two adults required to complete assembly* *Two adults required to complete assembly* Only adults should set up the product. Do not allow children in the setup area until assembly is complete. Only adults should set up the product. Do not allow children in the setup area until assembly is complete. 4

5 ASSEMBLY GUIDES Refer to the following areas throughout the instructions to assist in the assembly process: This area is located at the top, left-hand corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page. TOOLS AND HARDWARE REQUIRED FOR THIS PAGE This area is usually located in the bottom, left-hand corner of a step and indicates that special attention is needed to perform a particular part of a step.! Note: These areas are usually located in the bottom, right-hand corner of a step and indicate that damage to the product or serious injury may occur if the caution or warning is not heeded. CAUTION WARNING 5

6 PARTS LIST ID Item Description Qty HARDWARE LIST ID Item Description Qty BCO Pole Assembly Hardware BCQ Pole to Base Assembly Hardware 6

7 HARDWARE LIST ID Item Description Qty BCQ Pole to Base Assembly Hardware, Continued BCS Backboard & Rim Assembly Hardware BCR Backboard to Pole Assembly Hardware BCT Handle Assembly Hardware BCU Frame Pad Assembly Hardware 7

8 Parts shown at 10% of Actual Size PARTS IDENTIFIER ALH 43 3/8 ALF 43 3/8 ALE 27 5/8 AKI BGO BGP BAB ALI 38 ALS 31 BAA AKF 21 3/4 AJD AJQ 8 AJO

9 Parts shown at 10% of Actual Size PARTS IDENTIFIER ALX AKZ AMN Parts shown at 5% of Actual Size AJI AJM 9

10 Parts shown at 25% of Actual Size PARTS IDENTIFIER ALM AJN AMU ALL ALD AMX BLC AKP AMA BGR 10

11 POLE ASSEMBLY HARDWARE [BCO] Hardware shown at Actual Size HARDWARE IDENTIFIER ABE ABR ABB ABZ ADS AAF CIH POLE TO BASE ASSEMBLY HARDWARE [BCQ] Hardware shown at Actual Size DRZ AAE AAO ABD CCL 11 BTS

12 HARDWARE IDENTIFIER BACKBOARD TO RIM ASSEMBLY HARDWARE [BCS] Hardware shown at Actual Size EAP AAQ ABK AAV ADR Hardware shown at 25% of Actual Size AOW AJW APZ ABQ APY BACKBOARD TO POLE ASSEMBLY HARDWARE [BCR] Hardware shown at Actual Size 7 1/16 AAD AAX 12

13 HARDWARE IDENTIFIER BACKBOARD TO POLE ASSEMBLY HARDWARE (CONTINUED) Hardware shown at Actual Size 5 AQD ANS ANP ANU ANQ AQB ABP AOR AQC AAN ANK 13

14 HANDLE ASSEMBLY HARDWARE [BCT] Hardware shown at Actual Size HARDWARE IDENTIFIER 7 1/16 AAI AAD 6 1/2 AAH ABA 6 1/2 AOR AAW ABM APR ALV AAX ABB FRAME PAD ASSEMBLY HARDWARE [BCU] Hardware shown at Actual Size ADP 14

15 1 BCO POLE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size ABE ABR ABZ ADS CIH AAF ABB 15

16 1 POLE ASSEMBLY PARTS REQUIRED Parts shown at 10% of Actual Size ALH 43 3/8 ALF 43 3/8 ALE 27 5/8 Part shown at 25% of Actual Size ALL TOOLS REQUIRED 9/16 Wrench Phillips Screwdriver Electric Drill 16 Scrap Wood

17 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO TOOLS REQUIRED FOR THIS PAGE ABE ABR 1.1 AAF 3/8 x 4 Hex Bolts (ABE) 3/8 Washers (AAF) Top Pole (ALH) 1/2 x 3.41 Spacers (ABR) ABE AAF ABR Small holes Large holes ALH 17

18 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 9/16" ABB 1.2 Pole Bracket (ALL) 3/8 x 4 Hex Bolts (ABE) Top Pole (ALH) ABE ABB ALL ALH 18

19 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADS CIH 1.3 Top Pole (ALH) Middle Pole (ALF) 1/4 x 3/4 Screw (ADS) ALH ALH CIH ADS ALF ALF Warning Sticker! Note: The 1/4 x 3/4 Screw should be fl ush with the Pole, but will spin freely once installed. Do not jam the Poles together until instructed. 19

20 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADS CIH 1.4 Middle Pole (ALF) Bottom Pole (ALE) 1/4 x 3/4 Screw (ADS) Make sure the indented lip on the Bottom Pole and the Pole Bracket (ALL) are on opposite sides of the pole assembly. ALL ALH ALF CIH ADS ALF ALE ALE! Note: The 1/4 x 3/4 Screw should be fl ush with the Pole, but will spin freely once installed. Do not jam the Poles together until instructed. 20

21 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE 1.5 ATTENTION: THIS STEP CANNOT BE REVERSED! Top and Middle Poles (ALH & ALF) Middle and Bottom Poles (ALF & ALE) DO NOT COMPLETE ASSEMBLY ALE ALF ALH WARNING The Poles must be seated together! Even if the Poles cover the slots before seating, they must be struck on a hard surface five to six times! Failure to seat the Poles correctly could allow the Poles to separate during use, which could lead to serious personal injuries or property damage.! Note: Do not hit your feet with the Pole sections, as serious injury could occur. 21

22 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ABZ 1.6 #14 x 1 Self-Tapping Screws (ABZ) ALH ABZ ALF ABZ ALE! Note: Chuck the #14 x 1 Self-Tapping Screw directly into an Electric Drill for easy installation, or use a 3/8 Hex Driver. 22

23 2 BCQ POLE TO BASE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size BZP (x1) 1/4 x 3 1/2 Shoulder Bolt AAE Part shown at 5% of Actual Size AAO BTS PARTS REQUIRED Parts shown at 25% of Actual Size AMU ABD AJM AJN Parts shown at 10% of Actual Size ALI 21 3/4 AJD 38 TOOLS REQUIRED 1/2" Wrench Rubber Mallet 23 3/16 Allen Wrench

24 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE 2.1 Base Cap (AJN) Base (AJM) Rubber Gasket AJN AJM AJN! 2.2 Note: Make sure the Rubber Gasket is inside the Base Cap. 1/2 x 21 3/4 Axle (AJD) Wheels (AMU) Base (AJM) Bottom Pole (ALE) with the lip at the bottom of the pole facing outward. ALE AJM AMU AMU AJD! Note: It may be necessary to use a Rubber Mallet to tap the Axle into place. 24

25 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2" 3/16" BZP AAE AAO ABD BTS 2.3 Pole Brace (ALI) Base (AJM) ALI! 2.4 AAE ABD ABD AJM AAO Note: Repeat this step to install the other Pole Brace to the other side of the Base. Pole Braces (ALI) Bottom Pole (ALE) BTS ALI ALI BZP ALE! Note: Tip the system backward so the Pole rests on the ground. Do not stand the system up until it is filled with either sand or water later in the assembly. 25

26 3 BACKBOARD TO RIM ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size EAP AAQ ABK AAV ADR Hardware shown at 25% of Actual Size AOW AJW APZ ABQ Part shown at 10% of Actual Size APY PARTS REQUIRED ALX 26

27 3 BACKBOARD TO RIM ASSEMBLY PARTS REQUIRED Part shown at 5% of Actual Size AJI Parts shown at 25% of Actual Size BGR AMA ALD TOOLS REQUIRED 1/2 Wrench Phillips Screwdriver 27 1/2 Socket Wrench

28 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2 EAP APY ABQ AAQ 3.1 5/16 x 1 Carriage Bolts (EAP) Rim Pivot Bracket (APY) EAP EAP APY 3.2 3/8 Push Nut (AAQ) 3/8 x 5 1/2 Axle (ABQ) ABQ AAQ! Note: The Push Nut should rest about 1/4 from the end of the Axle. If the Push Nut slips on too far, continue sliding it to the other end of the Axle to remove it and try again. 28

29 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2 1/2 AAQ ABK 3.3 3/8 x 5 1/2 Axle (ABQ) Rim (ALX) Rim Pivot Bracket (APY) Push Nut (AAQ) ALX ABQ 3.4 APY ABQ AAQ Plastic Guard (ALD) Backboard (AJI) AJI ALD 29 ABK ABK

30 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2 APZ AAV U-Bolt (APZ) U-Bolt Washer Plate (BGR) Backboard (AJI) AJI APZ BGR 3.6 5/16 Jam Nuts (AAV) 4 U-Bolt (APZ) APZ AAV 30

31 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2 AOW AJW ABK ADR 3.7 Compression Springs (AJW) 4 U-Bolt (APZ) Spring Retainer Plate (AOW) 5/16 Nylock Flange Nuts (ABK) Rim (ALX) ABK AOW APZ AJW! Note: DO NOT COMPLETELY TIGHTEN THE 5/16 NYLOCK FLANGE NUTS IN THIS STEP! Only tighten the Nuts until the Rim (ALX) does not wobble. Tightening the Nuts will adjust the Rim tension. 3.8 Rim Cover Plate (AMA) Rim (ALX) ALX ADR ADR ADR AMA ADR 31

32 4 BACKBOARD TO POLE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size 7 1/16 AAD 5 AOR AQD AAN ANS ANQ ABP ANP ANU AAX AQB ANK 32 AQC

33 4 BACKBOARD TO POLE ASSEMBLY PARTS REQUIRED Parts shown at 10% of Actual Size BGO BGP ALS 31 Parts shown at 25% of Actual Size ALM BLC TOOLS REQUIRED 3/4 Socket Wrench 1/2 Wrench 11/16 Wrench 1/2 Socket Wrench Rubber Mallet 33 3/4 Wrench

34 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE 4.1 Tie Plate (BLC) Lower Extension Arm (BGP) BLC BGP 4.2 Tie Plate (BLC) Lower Extension Arm (BGP) BLC BGP 34

35 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1/2 AQC 1/2 AQB AAN 4.3 Lower Extension Arms (BGP) 5/16 x 3/4 Thread-Cutting Bolts (AQB) Tie Plate (BLC) AQB BLC BGP AAN BGP WARNING 4.4 Extension Arm Caps (AQC) Lower Extension Arms (BGP) BGP 35 AQC AQC

36 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/4 AAD 7 1/16 AOR ABP AAX 4.5 Lower Extension Arms (BGP) Top Pole (ALH) BGP ALH BGP AAX AOR AOR AAD ABP! Note: Tighten the 1/2 Centerlock Nut (AAX) until it is flush with the end of the Bolt. 36

37 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/4 3/4 5 AQD AAX ABP ANK 4.6 Upper Extension Arms (BGO) Top Pole (ALH) ANK ANK AAX ABP ABP AQD BGO ALH BGO! Note: Tighten the 1/2 Centerlock Nut (AAX) until it is flush with the end of the Bolt. 37

38 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/4 ANQ AOR ANP 11/16 ABP CAUTION: HAVE ONE ADULT HOLD THE BACKBOARD IN PLACE UNTIL ASSEMBLY HAS BEEN COMPLETED! 4.7 Lower Extension Arms (BGP) Backboard (AJI) 1/2 x 3 Bolts with Nylon Patches (ANQ) 1/2 x 1 3/4 Nut Coupler (ANP) BGP BGP AJI ANQ AOR ANP AOR ANQ ABP ABP ABP AOR ANQ ANP ANQ AOR! Note: Make sure that the 1/2 x 3/8 Poly Spacers (ABP) positioned between the Lower Extension Arms and the Backboard do not bulge. 38

39 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/4 ANU AOR ANK AAX 4.8 Upper Extension Arms (BGO) Backboard (AJI) AAX AOR ANK ANU BGO ANU BGO AOR ANK AAX! Note: Tighten the 1/2 Centerlock Nuts (AAX) until they are flush with the end of the Bolts. 39

40 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO TOOLS REQUIRED FOR THIS PAGE ANS 4.9 1/2 Nylon Plugs (ANS) Backboard (AJI) AJI ANS ANS ANS ANS 4.10 Pole Cap (ALM) Top Pole (ALH) ALM ALH 40

41 5 BCT HANDLE ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size Hardware shown at Actual Size 7 1/16 AAI AAD 6 1/2 AAH ABA 6 1/2 AOR AAW ABM APR ALV AAX ABB 41

42 5 HANDLE ASSEMBLY PARTS REQUIRED Parts shown at 10% of Actual Size ALS 31 AKI AKF Parts shown at 25% of Actual Size AJO AMN AMX AKP TOOLS REQUIRED 9/16" Wrench 3/4" Wrench Pliers 42

43 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE AAI AAH 5.1 Gas Spring (AKF Bellows (AJO) AMX AJO 1/2 AJO AMX 1 AKF AKF! 5.2 Note: Use Pliers to tighten the Zip Ties (AMX) securely, then cut off the ends of the Zip Ties. Pole Bracket (ALL) Cotter Pin (AAH) Clevis Pin (AAI) ALL AAI ALL AAI AAH AAH 43

44 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 6 1/2 9/16 ABA ABB 5.3 Trigger (AMN) Handle (AKI) AMN ABB AKI ABA! 5.4 Note: Tighten the 3/8 Centerlock Nut (ABB) until it is flush with the end of the Bolt. Height Sticker (AKP) Top Pole (ALH) ALH AKP ALF Warning Sticker 44

45 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 6 1/2 3/4 AAW ALV AAX 5.5 Release Pin (ALV) Gas Spring (AKF) AKF ALV 5.6 Handle (AKI) Gas Spring (AKF) Release Pin (ALV) Trigger (AMN) Rear Lifter Arms (ALS) AKF ALV ALS AMN ALS AAW AKI AAX! Note: Tighten the 1/2 Centerlock Nut until it is flush with the end of the Bolt. 45

46 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 6 1/2 9/16 ABA ABB ABM 5.7 Handle (AKI) Middle Pole (ALF) 3/8 x 1/2 Spacers (ABM) AKI ALF ABA ABM ABM ABB 46

47 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3/4 AAD 7 1/16 AOR APR AAX 5.8 Rear Lifter Arms (ALS) Lower Extension Arms (BGP) 3/4 x 4 1/5 Spacer (APR) AOR APR AOR AAD AAX ALS ALS BGP BGP WARNING! Note: The Rear Lifter Arms must be on the inside of the Long Extension Arms. 47

48 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO TOOLS OR HARDWARE REQUIRED FOR THIS PAGE 5.9 Grease Packet (AKH) Release Pin (ALV) ALV 48

49 6 FINAL ASSEMBLY HARDWARE REQUIRED Hardware shown at Actual Size ADP Parts shown at 10% of Actual Size PARTS REQUIRED BAA BAB AKZ AJQ TOOLS REQUIRED Funnel Sand Water Hose 49 Electric Drill

50 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADP 6.1 Backboard (AJI) Left and Right Frame Pads (BAA & BAB) ADP ADP BAB AJI ADP ADP BAA 50

51 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADP 6.2 Center Frame Pads (AJQ) Backboard (AJI) AJI ADP AJQ ADP ADP AJQ ADP ADP ADP AJI 51

52 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE Two adults are required to complete assembly. To prevent serious injuries, the Pole should be held down by one adult at all times while the Base is being filled. 6.3 OPTION A: FILLING WITH SAND Base (AJM) Base Cap (AJN) WARNING For safety reasons, we recommend that sand be used instead of water to fill the Base. If a leak develops, water could run out unnoticed, allowing the system to fall over, resulting in serious personal injuries, or property damage. If using Water, check the Base carefully for leaks. If a leak is found, lay the system down on the ground and call Customer Service. Do not use, stand up, or play on a leaking system. AJM 52

53 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE Two adults are required to complete assembly. To prevent serious injuries, the Pole should be held down by one adult at all times while the Base is being filled. 6.3 OPTION B: FILLING WITH WATER Base Cap (AJN) Base (AJM) AJM 53

54 TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO TOOLS OR HARDWARE REQUIRED FOR THIS PAGE 6.4 Net (AKZ) Rim (ALX) ALX AKZ! Note: If a replacement Net is needed, please call our Customer Service Department. Our Nets are shorter than average to reduce the risk of entanglement. 54

55 OPERATION OF HEIGHT ADJUSTMENT SYSTEM To Adjust the Height of the Hoop: MOVING THE SYSTEM WARNING: CAUTION: POLE CARE AND SYSTEM MAINTENANCE IF RUST HAS PENETRATED THROUGH THE POLE ANYWHERE, REPLACE IT IMMEDIATELY! 55

56 NOTES 56

57 NOTES 57

58 ENHANCE YOUR LIFETIME PURCHASE BY ADDING ACCESSORIES OR OTHER GREAT PRODUCTS: To purchase accessories or other Lifetime Products, visit us at: Or call:

59 WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. ADVERTENCIA SI NO SE OBEDECEN ESTAS ADVERTENCIAS PUEDEN PRODUCIRSE GRAVES LESIONES Y/O DAÑOS A LA PROPIEDAD. AVERTISSEMENT FAUTE DE NE PAS SUIVRE CES AVERTISSEMENTS, VOUS RISQUEZ DE CAUSER DES BLES- SURES GRAVES ET/OU DES DOMMAGES À L ÉQUIPEMENT. #FS /12/

60 WARRANTY INFORMATION LIFETIME BASKETBALL EQUIPMENT 5-YEAR LIMITED FACTORY WARRANTY THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE. ALL WARRANTY CLAIMS MUST BE ACCOMPANIED BY A SALES RECEIPT. REPORT PRODUCT DEFECTS IN WRITING TO: To register the product, visit our Web site at