Compact Cordless Screwdriver Kit. Owner s Manual

Transcription

1 Compact Cordless Screwdriver Kit Owner s Manual CAUTION: Before using this cordless screwdriver or any of its accessories, read this manual and follow all safety rules and operating instructions. Imported by Mastercraft Canada Toronto, Canada M4S 2B8 Rev /11/2009

2 TABLE OF CONTENTS SECTION PAGE SECTION PAGE Specifications Location of parts Warranty Accessories & unpacking Power tool safety. 5 7 Contents 11 Specific safety rules 7 Assembly & operation instructions Battery & charger safety Maintenance Symbols 9 Exploded view.. 18 Parts list SPECIFICATIONS Rotation.. Single speed.. Battery. Charger input. Charger output.. Plug-in battery charger. Drive... Weight... Right or left 220 RPM 3.6 V 120 V AC, 60 Hz 6 V, 300 ma 3 5 Hours ¼ (0.63 cm) hex 13 oz (0.37 kg) 2

3 WARRANTY 3-Year Limited Warranty This Mastercraft product is guaranteed for a period of 3 years from the date of original retail purchase against defects in workmanship and materials, except for the following components: a) Component A: Batteries, chargers and carrying cases, which are guaranteed for a period of 2 years from the date of original retail purchase against defects in workmanship and materials; b) Component B: Accessories which are guaranteed for a period of 1 year from the date of original retail purchase against defects in workmanship and materials. Subject to the conditions and limitations described below, this product, if returned to us with proof of purchase within the stated warranty period and if covered under this warranty, will be repaired or replaced (with the same model, or one of equal value or specification),at our option. We will bear the cost of any repair or replacement and any costs of labour relating thereto. These warranties are subject to the following conditions and limitations: a) A bill of sale verifying the purchase and purchase date must be provided; b) This warranty will not apply to any product or part thereof that is worn or broken or that has become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation, operation or maintenance (as outlined in the applicable owner s manual or operating instructions) or that is being used for industrial, professional, commercial or rental purposes; c) This warranty will not apply to normal wear and tear or to expendable parts or accessories that may be supplied with the product that are expected to become inoperative or unusable after a reasonable period of use; d) This warranty will not apply to routine maintenance and consumable items, including but not limited to fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or adjustments; e) This warranty will not apply where damage is caused by repairs made or attempted by others (i.e.: persons not authorized by the manufacturer); f) This warranty will not apply to any product that was sold to the original purchaser as a reconditioned or refurbished product (unless otherwise specified in writing); Page 1 of 2 3

4 WARRANTY 3-Year Limited Warranty cont d These warranties are subject to the following conditions and limitations: g) This warranty will not apply to any product or part thereof if any part from another manufacturer is installed therein or any repairs or alterations have been made or attempted by unauthorized persons; h) This warranty will not apply to normal deterioration of the exterior finish including but not limited to scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical cleaners; and i) This warranty will not apply to component parts sold by and identified as the product of another company, which shall be covered under the product manufacturer s warranty, if any. Additional Limitations This warranty applies only to the original purchaser, and cannot be transferred. Neither the retailer nor the manufacturer shall be liable for any other expense, loss or damage, including but not limited to any indirect, incidental, consequential or exemplary damages arising in connection with the sale, use or inability to use this product. Notice to Consumer This warranty gives you specific legal rights, and you may have other rights, which may vary from province to province. The provisions contained in this warranty are not intended to limit, modify, take away from, disclaim or exclude any statutory warranties set forth in any applicable provincial or federal legislation. Mastercraft is a superior line of products selected for their workmanship and materials. These products are designed to meet rigorous quality and performance standards, and are approved by our Quality Assurance laboratory. TOLL-FREE HELPLINE: Page 2 of 2 4

5 WARNING: Before using this power tool, it is critical that these safety rules are read and understood. Failure to follow these rules could result in serious injury or damage to the power tool. Good safety practices are a combination of common sense, staying alert and understanding how this power tool works. To avoid mistakes that could cause serious injury, do not use this power tool until all safety rules have been read and understood. READ and become familiar with this entire Owner s Manual. LEARN the tool s applications, limitations and possible hazards. WARNING: Look for this symbol that identifies important safety precautions. It means CAUTION BE ALERT PERSONAL SAFETY IS INVOLVED KEEP GUARDS IN PLACE and in working order. ALWAYS WEAR EYE PROTECTION. Any power tool can throw foreign objects into your eyes which could cause permanent eye damage. ALWAYS wear safety goggles (not glasses) that comply with ANSI safety standard Z87.1. Everyday glasses have only impact resistant lenses. They ARE NOT safety glasses. POWER TOOL SAFETY WARNING: Glasses or goggles not in compliance with ANSI Z87.1 could cause serious injury when they break. WORK AREA Keep work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in environments where explosive elements, such as flammable liquids, gas or dust are present. Power tools create sparks which may ignite the dust or fumes. Keep bystanders, children and visitors away while operating this tool. Distractions can cause loss of control. PERSONAL SAFETY Stay alert, watchful and use common sense when operating a power tool. Do not use the tool while tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Dress properly. Do not wear loose clothing or jewellery. Contain long hair. Keep hair, clothing and gloves away from moving parts. Loose clothing, jewellery or long hair can be caught in moving parts. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE 5

6 POWER TOOL SAFETY PERSONAL SAFETY continued Avoid accidental starting. Be sure power switch is OFF before plugging in. Carrying tools with finger on the switch or plugging in tools that have the switch ON invites accidents. Remove adjusting keys or wrenches before turning the tool ON. A wrench or key that is left attached to a rotating or moving part of the tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat and/or hearing protection must be used in appropriate conditions. TOOL USE AND CARE Use clamps or another practical method to secure and support the workpiece on a stable platform. Holding the workpiece by hand or against the body is unstable, unsafe, and may lead to loss of control. Do not force the tool. Use the correct tool for the required application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use the tool if the power switch does not turn it ON or OFF. Any tool that cannot be controlled by the switch is dangerous and must be repaired. Disconnect the plug from the power source before making any adjustments, changing accessories or storing the tool. Such preventative safety measures reduce the risk of the tool starting accidentally. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the tool s operation. If damaged, have the tool serviced before using. Numerous accidents are caused by poorly maintained tools. Use only accessories that are recommended by the manufacturer for this model. Accessories that may be suitable for one tool may be hazardous when used with another tool. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE 6

7 TOOL USE AND CARE continued Keep the tool and its handle dry, clean and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum based products or any strong solvents to clean this tool. Following this rule will reduce the risk of fire, loss of control and deterioration of the plastic components of the tool. SERVICE Tool service must be performed only by qualified personnel. Service or maintenance performed by unqualified personnel could result in risk of injury. When servicing a tool, use only identical replacement parts. Follow instructions in the maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES WARNING: For safety reasons, do not plug in the charger, charge the battery or operate the tool until this Owner s Manual has been read and understood. Always use safety goggles or other suitable eye protection. Always check to make sure the area where screws are being driven does not have any hidden wiring. Contact with a live wire will make exposed metal parts of the tool live and could result in an electric shock to the operator. POWER TOOL SAFETY 7 Do not drive screws or break into existing walls or other blind areas where electrical wiring may exist. If this situation is unavoidable, remove all fuses or disconnect all breakers feeding the work area. Secure the workpiece in a vice or with clamps. Never hold in hand or across legs. The rotating action of the screwdriver may cause the bit to come loose from the screw and cause injury. Never carry the cordless screwdriver with finger on the switch. The tool is always in an ON condition when the battery is charged. Never hold the body of the cordless screwdriver near the switch while changing screwdriver bits. Accidentally touching the switch may start the tool and possibly cause an injury. Always use the correct shape of screwdriver bit that matches the head of the screw. Always use the largest size screwdriver bit that will properly fit into the head of the screw. Do not use worn or damaged screwdriver bits. Worn or damaged screwdriver bits will not drive the screw properly and may jump out of the screw head, causing possible injury. Always insert the magnetic bit holder fully into the collet. If not fully inserted, the magnetic bit holder may jump out of the collet and cause damage to the workpiece or possible injury. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

8 BATTERY & CHARGER SAFETY WARNING: The lithium-ion battery is an integral part of the tool. If it no longer charges properly or is damaged, the tool and battery must not be discarded as household trash, burnt or thrown into water. The tool and battery must be disposed of as hazardous waste in accordance with all municipal requirements. Do not incinerate a discarded battery. It can explode in a fire. Do not use an extension cord. Plug the charger cord directly into an electrical outlet. For best results, charge the battery when the temperature range of the battery and the work area is 0 40 C ( F). Unplug the charger when not in use and before cleaning or maintenance. Do not abuse the cord. To reduce the risk of damage to the electric cord or plug, never carry the charger by the cord or yank the cord to unplug. Always grasp the plug and pull to disconnect. Always keep the cord away from heat, oil and sharp edges. Charge the battery only with the charger supplied with this cordless screwdriver. Do not use the charger in wet or damp conditions. It is intended for indoor use only. Do not use the charger near sinks or bathtubs. Do not immerse the charger in water. Do not allow the cord to hang over the edge of a table or counter or touch hot surfaces. The charger should be placed away from sinks and hot surfaces. Do not use charger to charge any batteries other than the cordless screwdriver battery. Other batteries may explode. Do not operate charger if cord or plug is damaged. Replace damaged cord and plug immediately. Do not operate charger if it has received a sharp impact, been dropped or otherwise damaged in any way. Have a qualified technician examine the charger and repair it if necessary. Do not disassemble the charger. 8

9 SYMBOLS WARNING: Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow better and safer operation of the tool. V A Hz W kw L kg h N/cm 2 pa min s volts amperes hertz watt kilowatts microfarads litres kilograms hours newtons per square centimeter pascals minutes seconds alternating current three-phase alternating current three-phase alternating current with neutral direct current no load speed alternating or direct current class II construction splash-proof construction watertight construction protective earthing at earthing terminal, Class I tools revolutions or reciprocations per minute diameter off position arrow warning symbol LISTED JD5010 This symbol designates that this tool is listed with Canadian requirements by ETL Testing Laboratories, Inc. Conforms to UL Std , Certified to CAN/CSA Std. C22.2 No ,

10 LOCATION OF PARTS Collet LED light Left/right switch Charging indicator light Charger receptacle ACCESSORIES AVAILABLE ACCESSORIES WARNING: Use only accessories recommended for this cordless screwdriver. Follow instructions that accompany accessories. Use of improper accessories may cause injury to the operator or damage to the cordless screwdriver. Do not use any accessory unless the Owner s Manual for the accessory has been read and completely understood. UNPACKING WARNING: If a part is missing or damaged, do not plug the charger into the power source or install a bit in the screwdriver until the missing or damaged part is replaced and assembly is complete. Carefully unpack the cordless screwdriver and all components. Compare against the Cordless Screwdriver Components chart on page 9. Screwdriver bits 10

11 CONTENTS COMPACT CORDLESS SCREWDRIVER COMPONENTS KEY DESCRIPTION QTY A Cordless screwdriver 1 B Charger 1 C Screwdriver bits: #0, 1, 2, 3 #0, 1, 2, 3 5/32, 7/32 15 T10, T15, T20, T25 Magnetic bit adapter D Nylon holster 1 Owner s manual 1 11

12 ASSEMBLY & OPERATION INSTRUCTIONS CHARGING THE BATTERY 1. Place the cordless screwdriver near a 120 V, 60 Hz electrical outlet. 2. Insert the battery charger plug (1) into the charger receptacle (2) in the handle of the cordless screwdriver (3) (Fig. 1). 3. Plug the battery charger (4) into a 120 V 60 Hz wall receptacle. NOTES: a) The red indicator light (5) in the handle will turn ON, indicating the battery is being charged. b) The red indicator light will remain ON until the battery is fully charged. c) A new battery or one that is completely exhausted should be charged for 5 hours or until the charger shuts down and the red indicator light goes OFF. After normal use, a battery should be fully charged in about 3 hours. d) If the battery does not charge properly, check to make sure the electrical outlet is live and that the temperature range in the work area is between 0 40 C ( F). INSTALLING SCREWDRIVER BITS WARNING: Never hold the cordless screwdriver with fingers near the switch while changing screwdriver bits. Accidentally touching the switch may start the tool and possibly cause an injury. 1. Insert the small end of the magnetic bit holder (1) into the collet (2) of the tool (Fig. 2). NOTE: Push the bit holder as far as it will go into the collet. 2. Select an appropriate screwdriver bit that fits the head of the screw being driven. NOTES: a) Use the largest size screwdriver bit that will properly fit the screw head. b) Make sure the screwdriver bit is in good condition and is neither damaged nor worn. 3. Insert the screwdriver bit (3) fully into the large end of the magnetic bit holder (4). NOTE: Make sure the screwdriver bit is fully inserted into the magnetic bit holder until it is held in place by the magnet. Fig. 1 Fig. 2 12

13 ASSEMBLY & OPERATION INSTRUCTIONS RIGHT/LEFT SWITCH The Compact Cordless Screwdriver is equipped with a convenient switch that functions as both an ON/OFF switch and a right/left switch. 1. To drive screws, press the upper part of the switch (1) (Fig. 3). To turn the switch OFF, release the switch. 2. To remove screws, press the lower part of the switch (2). Fig. 3 SCREWDRIVER LIGHT The cordless screwdriver is equipped with a LED light (1) (Fig. 4). The light will automatically turn ON when the switch is pressed. It will also turn OFF when the switch is released. PREPARING SCREW HOLES It is important to prepare screw holes before attempting to fasten two pieces of wood together. Proper preparation will make screws drive easier and prevent misaligned components, stripped screw heads, splitting and separating of wood components. 1. Clamp components that are to be screwed together in their desired position (Fig. 5). 2. Drill a pilot hole (1) through the outer piece (2) and into the inner piece (3). Drill hole 2/3 the diameter of the smooth portion of the screw shank. NOTE: If the wood is soft, drill the hole 2/3 the length of the screw. If the wood is hard, drill the hole the full length of the screw. 3. Remove the clamp from the two pieces to be screwed together. 4. Enlarge the hole (1) in the outer piece (2) so it is the same size as the smooth portion of the screw shank (Fig. 6). 5. If using a flat head screw, counter-sink the hole (4) so the head of the screw will be flush with the surface when fully driven into place. Fig. 6 Fig Fig. 5

14 ASSEMBLY & OPERATION INSTRUCTIONS NYLON HOLSTER This cordless screwdriver is equipped with a holster that provides a convenient method of keeping both the tool and the bits close at hand. This function is particularly handy when performing repetitive operations. Attach the holster to a belt on the right hand side for easy access to the bit pockets: 4. Place the cordless screwdriver (4) in the holster (Fig. 8). NOTE: When placing the tool in the holster, do not push it too far into the holster to avoid the switch from being turned ON. 5. Place required accessory bits (5) and pencil (6) in pockets as shown. 1. Pull the loop strap (1) away from the hook strip (2) on the inside of the holster (Fig. 7). 2. Slide the opened loop strap over the belt (3). 3. Firmly press the loop strap onto the hook strip so it forms a belt loop that will hold the holster in place on the belt. Fig. 8 Fig. 7 14

15 ASSEMBLY & OPERATION INSTRUCTIONS LITHIUM-ION BATTERY PERFORMANCE Lithium-ion rechargeable batteries generally provide superior performance to nickel-cadmium batteries when used in power tools. Faster charges Longer battery life More power Lighter weight Lithium-ion batteries perform best and deliver peak output power at room temperature (20 C or 68 F). When operated in lower temperatures, the battery output will be reduced and it will NOT function below 20 C (-4 F). The output power will increase as the heat generated by the battery during use increases the internal temperature of the battery. The result is increased power as the tool is used. WARNING: Ensure to read POWER TOOL SAFETY, SPECIFIC SAFETY RULES, EXTENSION CORD SAFETY and SYMBOLS on pages 3 through 7 of this Manual before operating this Compact Cordless Screwdriver. Every time you the cordless screwdriver is used, the following should be verified: 1. Screwdriver bit is the correct type & size, not worn and not damaged in any way. 2. Workpiece is properly secured. 3. Safety glasses are being worn. Failure to adhere to these safety rules can greatly increase the chances of injury or property damage. DRIVING SCREWS When driving screws, care must be taken to use the bit that correctly fits the head of the screw being driven. Make sure to use the largest bit size that will properly fit into the head of the screw. The bits must also be in good condition and not worn so they will drive screws without slipping out of the screw head. 1. Select the correct screwdriver bit for the screw being driven. 2. Insert the magnetic bit holder (1) into the collet (2) (Fig. 9). 3. Insert the bit (3) fully into the bit holder. 4. Insert the screwdriver bit fully into the screw head (4). 5. While holding the screwdriver firmly against the screw and the bit aligned with the screw, press the upper part of the switch to start the screwdriver and drive the screw. 6. When the screw is driven to the correct depth, release the switch and the screwdriver will stop. 7. When the switch is released and the screwdriver stops turning, the spindle will automatically lock. Fully tighten the screw by manually rotating the screwdriver handle in a clockwise direction. 8. To remove screws, follow the same general procedure as for driving screws. When starting the screwdriver, press on the lower part of the switch. 15

16 ASSEMBLY & OPERATION INSTRUCTIONS DRIVING SCREWS continued GENERAL MAINTENANCE WARNING: When servicing, use only identical Mastercraft parts. Use of any other part may create a hazard or cause product damage. DO NOT use solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloth to remove dirt, dust, oil, grease, etc. WARNING: Do not at any time allow brake fluids, gasoline, petroleumbased products, penetrating oils, etc. to come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic. DO NOT abuse power tools. Abusive practices can damage the tool as well as the workpiece. Fig. 9 WARNING: DO NOT attempt to modify this cordless screwdriver or use accessories not recommended for this cordless screwdriver. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury. It will also void the warranty. LUBRICATION All of the bearings in this tool are lubricated with a sufficient amount of high-grade lubricant for the life of the unit under normal conditions. Therefore, no further lubrication is required. 16

17 BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING To preserve our natural resources, please recycle or dispose of batteries properly. This product contains lithium-ion batteries. Never dispose of lithium-ion batteries in normal household garbage or in landfill sites as they will add to the pollution of the environment. Consult the local waste authority for information regarding available recycling and disposal options. BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING WARNING: Upon removal of the battery, cover the terminals of the battery with electrical or heavy-duty adhesive tape. Never touch both terminals with metal objects or body parts as a short circuit may result. Keep away from children. Do not attempt to destroy or disassemble battery or remove any of its components. Lithiumion batteries must be recycled or disposed of properly. Failure to comply with these warnings could result in fire and serious injury. MAINTENANCE BATTERY MAINTENANCE For power, long operational life and light weight, this tool is powered by a lithium-ion battery. These lithium-ion batteries are powerful, rugged and will provide hundreds of charge/discharge cycles if properly maintained. NOTE: Never remove the battery in order to use it for any other purpose. This will void the warranty. How to care for the lithium-ion battery 1. Do not use the cordless screwdriver at temperatures below 10 C (14 F). 2. Never allow a battery to freeze. 3. Do not charge a battery that has been stored at or below 0 C (32 F) or above 40 C (104 F). Allow it to sit at room temperature for at least 30 minutes before charging. 4. Do not charge the battery if the tool seems warm to the touch. 5. To protect the battery this tool is equipped with a battery monitor circuit. When the battery voltage reaches the minimum manufacturer s recommended voltage, it interrupts the power to the tool, signalling that the battery should be charged. 6. The battery monitoring circuit shuts down at temperatures below -15 C (5 F) to protect the battery. 7. At very low temperatures battery output is severely reduced. However, it is safe to use the tool, as its output will increase to normal levels due to self-generated heat. 17

18 EXPLODED VIEW 18

19 PARTS LIST WARNING: Use only Mastercraft replacement parts. The use of any other parts may create a risk of injury or damage the cordless screwdriver. Any attempt to repair or replace the electronic components of the cordless screwdriver may create a risk of injury if it is not carried out by a qualified technician. Order by Part Number and not by the Code Number. Code Number Part Number Description Qty Stop Steel stop rod Retaining ring Collet Sleeve Gear case Pins Nesting ring Gear bushing Control block Planetary gear Planetary drive plate Planetary gear Locking plate Motor gear Screw, M2.5 x Motor flange Screw, ST2.5 x Motor Housing Switch PCB Battery pack Self-tapping screw 6 19