SPECIFICATIONS MODEL NO. OZBG150WA
|
|
- Kimberly Greer
- 5 years ago
- Views:
Transcription
1
2 SPECIFICATIONS MODEL NO. OZBG150WA Input Power: 150W Input Voltage: 230V ~ 50Hz No Load Speed: 2950/min Wheel Diameter: 150mm (6 ) Wheel Thickness: 16mm Wheel Bore: 12.7mm Protection Class: 1 (earthed appliance) KNOW YOUR PRODUCT Eye Shield Bracket 2. Eye Shield 3. Grinding Wheel 4. Tool Rest 5. Tool Rest Bar 6. Tool Rest Adjusting Knob 7. On/Off switch 8. Mounting Hole 9. Rubber foot (not shown) 10. Wheel Guard 11. Wheel Guard Cover
3 TABLE OF CONTENTS SPECIFICATIONS - MODEL NO. OZBG150WA... Page 1 KNOW YOUR PRODUCT... Page 1 INTRODUCTION. Page 3 ELECTRICAL SAFETY Page 3 GENERAL POWER TOOL SAFETY WARNINGS Page 4 BENCH GRINDER SAFETY WARNINGS. Page 6 ASSEMBLY Page 6 OPERATION Page 8 MAINTENANCE. Page 9 SPARE PARTS.. Page 9 CONTENTS. Page 10 WARRANTY.. Page 11 2
4 INTRODUCTION Congratulations on purchasing an Ozito Bench Grinder. We aim to provide quality tools at an affordable price. We hope you will enjoy using this tool for many years. The Ozito Bench Grinder OZBG150WA has been designed to easily cope with all sharpening and grinding requirements. This tool is intended for DIY use only.! ELECTRICAL SAFETY! WARNING! When using mains-powered equipment, basic safety precautions, including the following, should always be followed to reduce risk of fire, electric shock, personal injury and material damage. Read and understand the manual prior to operating this tool. Save these instructions and other documents supplied with this tool for future reference. The electric motor has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate. Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand. If the supply cord is damaged, it must be replaced by a qualified electrician or a power tool repairer in order to avoid a hazard. If operating a power tool in a damp location is unavoidable use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. Using an Extension Lead Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective. When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and electric shock. 3
5 ! GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to! follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term power tool" in all of the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. 4
6 ! GENERAL POWER TOOL SAFETY WARNINGS d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. b) If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 5
7 ! BENCH GRINDER SAFETY WARNINGS This appliance is not intended for use by young or infirm persons unless supervised by a responsible person to ensure that they can use the appliance safely. Young children should be supervised to ensure that they do not play with the appliance. Never operate the bench grinder with cracked or damaged wheels. Always replace cracked or damaged grinding wheels immediately. Always disconnect the bench grinder from the power supply prior to making any adjustments. Always use safety equipment including, earmuff, goggles, gloves, hat and clothing when operating the bench grinder. Check and ensure that all fastening screws, bolts and nuts are securely tightened prior to operating the tool. Never use an object to slow or stop the grinding wheel whilst in motion. Ensure the eye shields and tool rests are properly adjusted. Always use the eye shields and tool rests. Don t use grinding wheels for cutting purposes. Ensure the bench grinder speed doesn t exceed the operating speed marked on replacement wheels. ASSEMBLY! WARNING! Turn off the bench grinder at the mains outlet before attempting assembly. Failure to do so may cause serious personal injury. Remove the bench grinder and contents from within the carton. Sit the bench grinder down on a table or bench with the switch side facing towards you. Note: Refer to diagram on page 1 for parts identification. Eye Shields (Fig. 1) 1. Assemble eye shields (2) by placing the raised metal sides of the eye shield bracket (1) to the upper wheel guard (10) aligning the hole in the upper wheel guard (10) and the slot in the eye shield bracket (1). 2. Fix the eye shield bracket (1) to the upper wheel guard (10) using the screws supplied with a flat washer and spring washer. Fig. 1 6
8 ASSEMBLY (cont.) Tool Rests (Fig. 2) 1. Assemble the tool rest (4) by placing it over the tool rest bar (5). The smaller, slightly angled portion of the tool rest (4) should be closest to you and facing down. The angle of the tool rest (4) should be adjusted according to the application. 2. Feed one of the bolts supplied through the tool rest bar (5) and tool rest (4) in the direction of the on/off switch (7). Place a flat washer and star washer over the threaded end of the bolt and secure by fastening tool rest adjusting knob (6). Note: For the tool rest (4) to work effectively, it should be no more than 1.6mm away from the grinding wheel (3). This will also aid in the deflection of stray sparks. As the wheel wears with use adjust the tool rest (4) accordingly. Mounting holes For extra stability, we recommend securing the bench grinder using the mounting holes (8) provided on the corners of the base. Secure to a bench or table using bolts (not supplied). Removing/Installing Grinding Wheels Fig. 2! WARNING! Turn off the bench grinder at the mains outlet before attempting to change grinding wheels. Failure to do so may cause serious personal injury. Abrasive wheels should be discarded when: 1. The diameter approaches that of the driving flanges. 2. The tool rest can no longer be correctly adjusted to the wheel diameter. 3. The wheel no longer grinds efficiently because of reduced peripheral speed. Note: Visually inspect wheels for damage or defects prior to fitting. 1. Remove the eye shield (2) and tool rest from the side of the bench grinder you wish to change wheels. 2. Loosen and remove the 3 sets of screws, flat washers, spring washers and nuts that hold the cover (11) over the wheel you wish to change (Fig. 3). Remove the cover (11). Fig. 3 7
9 ASSEMBLY (cont.) 3. Use a spanner or shifter to loosen the wheel lock nut. To remove the left wheel nut rotate clockwise. To remove the right wheel nut rotate anti-clockwise. Use one hand to lock the wheel in place and the other to loosen the nut. Remove the nut, outer flange, paper washer and old wheel (Fig. 4). Fig If you did not get paper washers with your new wheel, re-use the old ones. Fit the first paper washer over the spindle up against the inner flange. Fit the new wheel. Fit the second paper washer over spindle up against the wheel, then fit the outer flange and nut back to the spindle. Use one hand to lock the wheel in place and the other to tighten the nut. Note: If you are tightening the left wheel nut; tighten anti clockwise until the right wheel begins to turn. If you are tightening the right wheel nut, tighten clockwise until the left wheel begins to turn. 5. Ensure the new wheel is secured and rotates freely before proceeding. 6. Re-assemble the wheel cover (11), eye shield (2) and tool rest (4). 7. Switch on the bench grinder and ensure that the wheels are running in alignment before commencing use. OPERATION! WARNING! Do not grind with the eye shield raised: always wear safety glasses when operating the bench grinder. On/Off Switch Turn the bench grinder on by pushing the On/Off switch (7) to the I (On) setting. Once depressed it will remain on. Turn the bench grinder off by pushing the On/Off switch (7) to the O (Off) setting (Fig. 5). Fig. 5 Operation Turn the bench grinder on and stand to one side while the bench grinder reaches maximum speed. Guide the work against the tool rest and into the grinding wheel slowly and smoothly without bumping. Apply gradual pressure to allow the wheel to warm up evenly. Use only the pressure required to complete the job. By moving the work back and forth across the wheel you will prevent grooves. 8
10 MAINTENANCE Wheel Dressing Dressing a wheel is done to renew sharpness or to true up the face of a wheel. A build up of metals and dirt will become embedded in a wheel as it is used. Use a wheel dressing tool (not supplied) to clean wheels. This will also improve the bench grinder s performance. Note: New wheels sometimes require dressing to true up their face. Cleaning and Lubrication Use only mild soap and a moist cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Self lubricating bearings are used in the tool and periodic lubrication is not required. Note: Ozito Industries will not be responsible for any damage or injuries caused by repairing of the bench grinder by an unauthorised person or by mishandling of the tool. SPARE PARTS Limited spare parts are available subject to availability. Please contact your local Bunnings Special Orders Desk to order the required spare parts. Most common spare parts listed below Spare Part Part No. Single Eye Shield & Bracket Assembly SPOZWDBG Tool Rest Assembly SPOZWDBG250-43A Left hand threaded nut SPOZBG Right hand threaded nut SPOZBG Rubber foot Pack of 4 SPOZBG Switch SPOZBG Wheel flange SPOZBG DESCRIPTION OF SYMBOLS V Volts Hz Hertz ~ Alternating current W Watts /min ø Revolutions or reciprocation per minute no No load speed Diameter Warning Regulator compliance mark 9
11 CARING FOR THE ENVIRONMENT Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way. Please recycle where facilities exist. Check with your local council authority for recycling advice. Recycling packaging reduces the need for landfill and raw materials. Reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice. CONTENTS 1 x Bench Grinder OZBG150WA 4 x Flat Washers 2 x Eye Shields 2 x Spring Washers 2 x Tool Rests 2 x Star Washers 2 x Tool Rest Adjusting Knobs 2 x Nuts 2 x Screws 1 x Instruction Manual 2 x Bolts OZITO INDUSTRIES PTY LTD AUSTRALIA (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175 Telephone: Facsimile: Website: enquiries@ozito.com.au 10
12 WARRANTY YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE: `Australia New Zealand TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE. The benefits provided under this warranty are in addition to other rights and remedies which are available to you at law. Our goods come with guarantees that cannot be excluded at law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Generally you will be responsible for all costs associated with a claim under this warranty, however, where you have suffered any additional direct loss as a result of a defective product you may be able to claim such expenses by contacting our customer service helpline above. 3 YEAR REPLACEMENT WARRANTY Your product is guaranteed for a period of 36 months from the original date of purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it will be replaced in accordance with the terms of this warranty. Warranty excludes consumable parts, for example: grinding wheel, eye shield, flange. WARNING The following actions will result in the warranty being void. Professional, Industrial or high frequency use. If the tool has been operated on a supply voltage other than that specified on the tool. If the tool shows signs of damage or defects caused by or resulting from abuse, accidents or alterations. Failure to perform maintenance as set out within the instruction manual. If the tool is disassembled or tampered with in any way. OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175 OW5
BENCH GRINDER MODEL NO. OZBG150WA
BENCH GRINDER 150mm MODEL NO. OZBG150WA OPERATING INSTRUCTIONS To view our entire range visit www.ozito.com.au SPECIFICATIONS MODEL NO. OZBG150WA Input Power: 150W Input Voltage: 230V ~ 50Hz No Load Speed:
More informationELECTRIC ENGRAVER 15W WARRANTY INSTRUCTION MANUAL SPECIFICATIONS WHAT S IN THE BOX. ozito.com.au. Electric Engraver
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
More informationPower Paint Scraper 200W CPS-200. To view the full range visit: Instruction Manual 3 Year Replacement Warranty
Power Paint Scraper 200W Instruction Manual 3 Year Replacement Warranty CPS-200 WARNING! Read all safety warnings and all instructions Failure to follow the warnings and instructions may result in electric
More informationPower Carver 50W CPC-050. To view the full range visit: Instruction Manual 3 Year Replacement Warranty
Power Carver 50W Instruction Manual 3 Year Replacement Warranty CPC-050 WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock,
More informationWHAT S IN THE BOX METAL CUTTING SHEARS. Metal Cutting Shears 500W INSTRUCTION MANUAL SPECIFICATIONS. Hex Key. Max. Thickness: ozito.com.
WHAT S IN THE BOX METAL CUTTING SHEARS 500W INSTRUCTION MANUAL SPECIFICATIONS Motor: No load speed: Max. Thickness: Tool weight: 500W 0 1,600 rpm 1.2mm 2.2kg Metal Cutting Shears Hex Key ozito.com.au MCS-5000
More informationBENCH GRINDER. 150W 150mm WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au OZBG150WA WHAT S IN THE BOX
WHAT S IN THE BOX BENCH GRINDER 150W 150mm INSTRUCTION MANUAL Bench Grinder SPECIFICATIONS Motor: 150W Input: 230 240V ~ 50Hz No Load Speed: 2,950 min -1 Wheel Ø: 150 mm Wheel Thickness: 16 mm Wheel Bore
More informationMULTI PURPOSE SAW 500W INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au WHAT S IN THE BOX MSW Multi-purpose Saw. Blades x 3.
WHAT S IN THE BOX MULTI PURPOSE SAW 500W INSTRUCTION MANUAL SPECIFICATIONS Input: Voltage: No Load Speed: Stroke Length: Blade Fitment: Cutting Capacity: Weight: ozito.com.au 500W 230-240V ~ 50Hz 500-3000
More informationPLANER 400W INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au WHAT S IN THE BOX. Planer. Guide Fence. Spanner. Input Power: Planing Width:
WHAT S IN THE BOX PLANER 400W INSTRUCTION MANUAL SPECIFICATIONS Input Power: No Load Speed: Planing Width: Blade Type: Planing Depth: Rebate Depth: Weight: ozito.com.au 400W 16,000 / min 82mm HSS Blades
More informationCORDLESS GLUE GUN. 7.2V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au GGL-7000 WHAT S IN THE BOX. Cordless Glue Gun.
WHAT S IN THE BOX CORDLESS GLUE GUN 7.2V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Input: 7.2V Glue Stick Diameter: 7.2mm Glue Stick Length: 190mm Heating Time: 15sec Working Time: 45min Battery Power:
More information360 LINE LASER LEVEL. 20m Working Range WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au LLT-3605 WHAT S IN THE BOX
WHAT S IN THE BOX 360 LINE LASER LEVEL 20m Working Range INSTRUCTION MANUAL SPECIFICATIONS Battery: Laser Power: Working Range: Laser Diode: Accuracy: 6V DC (4 x AA Battery) Class 2,
More informationCORDLESS AIR PUMP. 12V Li-ion INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au LAP-4100 WHAT S IN THE BOX. Cordless Air Pump.
WHAT S IN THE BOX CORDLESS AIR PUMP 12V Li-ion INSTRUCTION MANUAL SPECIFICATIONS Input: Max Air Pressure: Flow Rate: Battery: Charge time: Weight with Battery: ozito.com.au 12V 160psi 14l/min 1.3Ah Li-ion
More informationCORDLESS LED TORCH INSTRUCTION MANUAL
WHAT S IN THE BOX CORDLESS LED TORCH INSTRUCTION MANUAL LED Torch SPECIFICATIONS Input: 18V Number of LEDs: 1 Cree LED 3W Brightness: 250 Lumen Weight: 0.2kg ozito.com.au Battery & Charger sold separately
More informationCordless Blower. 18 Volt OZCBL18VA. To view the full range visit: Operation Manual 2 Year Replacement Warranty
Cordless Blower 18 Volt Operation Manual 2 Year Replacement Warranty OZCBL18VA 1008 To view the full range visit: www.ozito.com.au SPECIFICATIONS - MODEL NO. OZCBL18VA Batteries: Charge time: No load speed:
More informationCORDLESS TORCH LIGHT. 18V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au PXTLS-900 WHAT S IN THE BOX. Torch Light
WHAT S IN THE BOX CORDLESS TORCH LIGHT 18V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Input: 18V Number of LEDs: 1 Brightness: 250 Lumen Weight: 0.2kg ozito.com.au Torch Light Battery & Charger sold
More informationDrill Driver. Cordless 18V. Operating Instructions XDD-180. XU1 Power tools
Cordless Operating Instructions XDD-180 18V Drill Driver XU1 Power tools 1 23 Letcon Drive, Bangholme, Victoria, Australia 3175 Telephone: 1800 069 486 Website: www.xuone.com.au XDD-180 0916 1 2 3 4 5
More informationRMT1201. ORIGINAL INSTRUCTIONS Cordless Multi-Tool
RMT1201 ORIGINAL INSTRUCTIONS Cordless Multi-Tool Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications. Safety GENERAL
More informationScrewdriver. Cordless 3.6V. Operating Instructions XSD-360. XU1 Power tools
Cordless Operating Instructions XSD-360 Screwdriver 3.6V XU1 Power tools 1 23 Letcon Drive, Bangholme, Victoria, Australia 3175 Telephone: 1800 069 486 Website: www.xuone.com.au XSD-360 0816 SAFETY INSTRUCTIONS
More informationCORDLESS BLOWER KIT INSTRUCTION MANUAL
WHAT S IN THE BOX Cordless Blower CORDLESS BLOWER KIT INSTRUCTION MANUAL 4.0Ah Battery & Fast Charger SPECIFICATIONS Voltage: 18V Battery: 4.0Ah Li-ion Charge Time: 80 min No Load Speed: 12,000/min Max.
More informationDRILL DRIVER 280W WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au DDC-280 WHAT S IN THE BOX
WHAT S IN THE BOX DRILL DRIVER 280W INSTRUCTION MANUAL SPECIFICATIONS Motor: 280W Chuck Size: 10mm Keyless No Load Speed: 0-750/min Torque Settings: 15 Drilling Capacities: Timber 25mm Aluminium 8mm Plastic
More informationoriginal instructions 18V Torch RFP1801
original instructions 18V Torch RFP1801 Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications. Safety GENERAL POWER
More information12V SUBMERSIBLE BILGE PUMP
WHAT S IN THE BOX 12V SUBMERSIBLE BILGE PUMP 1,700 L/H FLOW INSTRUCTION MANUAL SPECIFICATIONS Voltage: 12V DC Rated Input Power:36 Watt Max. Current: 3 Amp Max. Flow Rate: 1,700 litres/hour Max. Head:
More informationMULTI PURPOSE MIXER INSTRUCTION MANUAL. 1600w Variable Speed. Paddle KNOW YOUR PRODUCT
KNOW YOUR PRODUCT MULTI PURPOSE MIXER 1600w Variable Speed 2 Gear Settings 160mm Mixing Paddle INSTRUCTION MANUAL WARNING: Read all safety warnings and all instructions. Failure to follow the warnings
More information12V PORTABLE PRESSURE PUMP
WHAT S IN THE BOX 12V PORTABLE PRESSURE PUMP 600 L/H FLOW INSTRUCTION MANUAL 12V Pressure Pump SPECIFICATIONS Voltage: 12V DC Current: 4.5A Working Pressure: 17psi Max. Flow Rate: 10 litres/min Max. Lift:
More information1200W CaR PoliSheR en RS4900
1200W Car Polisher RS4900 RS4900 8 1 2 7 3 4 5 6 A B flat nozzle C D E F 1200W Car Polisher RS4900 G H flat nozzle I J K L 4 1200W Car Polisher COMPONT LIST 1 2 3 4 5 6 7 Variable speed control Switch
More informationDRILL DRIVER. 12V Lithium Ion WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au ZLDDS-012 WHAT S IN THE BOX
WHAT S IN THE BOX DRILL DRIVER 12V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Input: 12V Chuck Size: 10mm Keyless No Load Speed: 0-400 / 0-1500/min Torque Setting: 21 Max. Torque: 14Nm Weight: 1.2kg
More informationCORDLESS BLOWER KIT. 18V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au PXCBLK-018 WHAT S IN THE BOX. Cordless Blower.
WHAT S IN THE BOX CORDLESS BLOWER KIT 18V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Voltage: Battery: Charge Time: No Load Speed: Max. Air Speed: Weight: ozito.com.au 18V 1.5Ah Li-ion 2 Hours 12,000/min
More information10MM DRILL DRIVER INSTRUCTION MANUAL
STANDARD EQUIPMENT 10MM DRILL DRIVER INSTRUCTION MANUAL SPECIFICATIONS Input: 18V Chuck Size: 10mm Keyless No Load Speed: 0-550/min Torque Setting: 21 Max. Torque: 35Nm Weight: 0.9kg ozito.com.au 10mm
More informationCORDLESS AUTO-LOADING
WHAT S IN THE BOX CORDLESS AUTO-LOADING SCREWDRIVER 3.6V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Voltage: 3.6V Driver Bit Size: 6.35mm (1/4 ) No Load Speed: 210/min Battery: 1.3Ah Li-ion Charge Time:
More information4V LITHIUM-ION SCREWDRIVER OWNER S OPERATING MANUAL
CSD-4107BG 4V LITHIUM-ION SCREWDRIVER OWNER S OPERATING MANUAL Your screwdriver has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When
More informationCORDLESS HEDGE TRIMMER KIT INSTRUCTION MANUAL
WHAT S IN THE BOX Cordless Hedge Trimmer CORDLESS HEDGE TRIMMER KIT INSTRUCTION MANUAL SPECIFICATIONS Voltage: 18V Battery: 2.0Ah Li-ion Charge Time: 2.5Hrs No Load Speed: 2,200/min Max. Cutting Capacity:
More informationCORDLESS GRASS TRIMMER & SHEAR
WHAT S IN THE BOX Cordless Grass Trimmer / Shear CORDLESS GRASS TRIMMER & SHEAR Hedge Trimmer Blade Grass Shear Blade INSTRUCTION MANUAL SPECIFICATIONS Voltage: 18V No Load Speed: 1,200/min Hedge Trimmer:
More informationRPS1215 ORIGINAL INSTRUCTIONS. Cordless Pruner
RPS5 ORIGINAL INSTRUCTIONS Cordless Pruner Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical modification.
More informationFILE SANDER 260W WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au FSR-3000 WHAT S IN THE BOX
WHAT S IN THE BOX FILE SANDER 260W INSTRUCTION MANUAL SPECIFICATIONS Input: Power: Belt Speed: Belt Size: IP Rating: Weight: ozito.com.au 230-240V ~ 50Hz 260W 330-550m/min 13 x 457mm IP20 1.15kg File Sander
More informationWR 22SE WR 25SE WR25SE. Handling instructions
WR 22SE WR 25SE WR25SE Handling instructions GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric
More informationCORDLESS BLOWER. 36V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au BLL- 036 WHAT S IN THE BOX. Blower. Blower Tube.
WHAT S IN THE BOX CORDLESS BLOWER 36V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Voltage: 36V Battery: 3.0Ah Li-ion Charge Time: 3 Hours No Load Speed: 10,000-16,000/min Max. Air Speed: 252km/hr Weight
More informationCORDLESS SCREWDRIVER. 3.6V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au SDL-4000 WHAT S IN THE BOX. Cordless Screwdriver
WHAT S IN THE BOX CORDLESS SCREWDRIVER 3.6V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Voltage: 3.6V Chuck Size: 6.35mm Keyless No Load Speed: 200/min Torque Settings: 8 Max Torque: 3Nm Battery: 1.3Ah
More informationKNOW YOUR PRODUCT SETUP & PREPARATION CORDLESS BLOWER (PXCBLK-018) 1. Blow Tube 2. Blow Tube Release Tab 4. Trigger Switch 5. Battery Seating 3. Handl
WHAT S IN THE BOX Cordless Blower CORDLESS BLOWER INSTRUCTION MANUAL SPECIFICATIONS Voltage: 18V Battery: 4.0Ah Li-ion Charge Time: 80 min No Load Speed: 12,000/min Max. Air Speed: 210km/hr Weight: 2.0kg
More informationBuffer Polisher 110 Watt
Buffer Polisher 110 Watt Operation Manual 3 Year Replacement Warranty OZBP110WA To view the full range visit: www.ozito.com.au 0409 SPECIFICATIONS MODEL NO. OZBP110WA Motor size: 110W Input: 240V ~ 50Hz
More informationeclipse Instruction Manual 4.0V Li-Ion Screwdriver Part #:
eclipse Instruction Manual 4.0V Li-Ion Screwdriver Part #: 902-588 Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 TestEquipmentDepot.com Test Equipment Depot - 800.517.8431-99
More informationSPECIFICATIONS MODEL NO. LIR-012
SPECIFICATIONS MODEL NO. LIR-012 Motor: Charge time: No load speed: Chuck: Torque: Batteries: Weight with 1 battery: 12V 3 5 hours 0 350/min, 0 1150/min 10mm Keyless 15Nm 2 x 1.3Ah Lithium Ion 1.05kg KNOW
More information12V CONSTANT PRESSURE PUMP
WHAT S IN THE BOX PRESSURE PUMP 700 L/H FLOW INSTRUCTION MANUAL 12V Pressure Pump 6m Coiled Hose SPECIFICATIONS Voltage: 12V DC Max. Current: 6Amp Max. Pressure: 70psi (4.8bar) Max. Flow Rate: 700 litres/hour
More informationInstruction Manual. CORDLESS DRILL 18V Li-ion WITH IMPACT FUNCTION. Model SROM 1172
Instruction Manual CORDLESS DRILL 18V Li-ion WITH IMPACT FUNCTION Model SROM 1172 Our tool range has you covered for DIY. Whatever the job, make light work of it with MAKO tools. Product Features: 1. Keyless
More informationOPERATION MAINTENANCE. Trimming. Edging. completely stopped and the battery is
OPERATION MAINTENANCE 5. TRIMMING & EDGING WARNING! Always ensure the tool Has completely stopped and the battery is removed prior to any maintenance. Trimming Move the grass trimmer from side to side
More informationCORDLESS IMPACT DRIVER 18V Li-ion
WHAT S IN THE BOX CORDLESS IMPACT DRIVER 18V Li-ion INSTRUCTION MANUAL SPECIFICATIONS Input: Chuck Size: No Load Speed: Impact Rate: Max. Torque: Battery: Charge time: Weight with Battery: ozito.com.au
More informationOPERATOR'S MANUAL. Cat. No. C12 PC. To reduce the risk of injury, user must read and understand operator's manual.
OPERATOR'S MANUAL Cat. No. C12 PC M12 Cordless Copper Tubing Cutter To reduce the risk of injury, user must read and understand operator's manual. General POWER TOOL SAFETY WARNINGS WARNING Read all safety
More informationCORDLESS GRASS TRIMMER & SHEAR
STANDARD EQUIPMENT Cordless Grass Trimmer / Shear CORDLESS GRASS TRIMMER & SHEAR INSTRUCTION MANUAL SPECIFICATIONS Voltage: No Load Speed: Hedge Trimmer: Grass Shear: Max. Cutting Cap.: Weight: 18V 1,200/min
More informationInstruction Manual CORDLESS DRILL & DRIVER 18V. Model SROM 1170
Instruction Manual CORDLESS DRILL & DRIVER 18V Model SROM 1170 Product Features: Dear Valued Customer, Thank you for purchasing this Samson Power Tool. We are dedicated to providing quality Samson Power
More informationSPRAY GUN 500W WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au WHAT S IN THE BOX SGP-5000
WHAT S IN THE BOX SPRAY GUN 500W INSTRUCTION MANUAL SPECIFICATIONS Voltage: Power: Max. Flow Rate: Max Viscosity: Container Capacity: Nozzle: Weight: ozito.com.au 220-240V ~ 50Hz 500W 550ml/min 60 DIN-sec
More informationCordless Hedge Trimmer
Cordless Hedge Trimmer 460mm - 18 Volt Operation Manual 2 Year Replacement Warranty OZCHT18VA 1208 To view the full range visit: www.ozito.com.au SPECIFICATIONS - MODEL NO. OZCHT18VA Input: Charge time:
More informationSPRAY GUN 400W WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au WHAT S IN THE BOX SGP-300
WHAT S IN THE BOX SPRAY GUN 400W INSTRUCTION MANUAL SPECIFICATIONS Voltage: Power: Max. Flow Rate: Viscosity: Pot Capacity: Nozzle: Weight (tool only): ozito.com.au 230-240V ~ 50Hz 400W 450ml/min 20-80
More informationCORDLESS GRASS TRIMMER. 18V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au PXCLTS-018 WHAT S IN THE BOX. Grass Trimmer.
WHAT S IN THE BOX CORDLESS GRASS TRIMMER 18V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Voltage: No Load Speed: Cutting Diameter: Weight: ozito.com.au 18V 8,500/min 240mm 1.8kg Grass Trimmer Blades
More informationWR 16SE. de fr it nl es pt sv da no fi el pl hu cs tr ro sl sk bg sr hr uk ru. Handling instructions
en WR 16SE de fr it nl es pt sv da no fi el pl hu cs tr ro sl sk bg sr hr uk ru Handling instructions GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to
More informationSPECIFICATIONS MODEL NO. HTL-072
SPECIFICATIONS MODEL NO. HTL-072 Motor: 7.2V Input: 230-240V ~ 50Hz Cutting diameter: 8mm Charge time: 3-5 hours Run time: 40 minutes (approx.) Hedge trimmer blade length: 150mm Grass blade length/width:
More informationANGLE GRINDER KIT. 125mm (5 ) WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au AGS-0125 WHAT S IN THE BOX
Danger: Do not exceed the max. safe speed Danger: Do not exceed the max. safe speed Danger: Do not exceed the max. safe speed WHAT S IN THE BOX ANGLE GRINDER KIT 125mm (5 ) INSTRUCTION MANUAL SPECIFICATIONS
More informationCORDLESS HAMMER DRILL
WHAT S IN THE BOX CORDLESS HAMMER DRILL 18V NiCad INSTRUCTION MANUAL SPECIFICATIONS Input: 18V Chuck Size: 10mm Keyless No Load Speed: 0-350/min, 0-1250/min Torque Setting: 16 Max. Torque: 25Nm Gearbox:
More informationELECTRIC CAR POLISHER
ELECTRIC CAR POLISHER MODEL NO: CP254 PART NO: 6462108 OPERATION & MAINTENANCE INSTRUCTIONS LS0610 INTRODUCTION Thank you for purchasing this CLARKE electric car polisher. Before attempting to use this
More informationSAFETY AND OPERATING MANUAL. Lithium-Ion cordless hammer drill WX372 WX372.1 WX372.9
SAFETY AND OPERATING MANUAL 2 Original Instructions General Power Tool Safety Warnings WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result
More informationPAINT SPRAY SYSTEM 700W WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au WHAT S IN THE BOX PSS-7000
WHAT S IN THE BOX PAINT SPRAY SYSTEM 700W INSTRUCTION MANUAL SPECIFICATIONS Voltage: Power: Max. Flow Rate: Max Viscosity: Container Capacity: Nozzle: Weight: ozito.com.au 220-240V ~ 50Hz 700W 1000ml/min
More information2.0Ah BATTERY INSTRUCTION MANUAL
BATTERY SAFETY WARNINGS THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR BATTERY. 2.0Ah BATTERY INSTRUCTION MANUAL SPECIFICATIONS Input: Battery Capacity: Power Consumption: Weight:
More informationBELT SANDER 850W WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au BSV-9000 WHAT S IN THE BOX
WHAT S IN THE BOX BELT SANDER 850W INSTRUCTION MANUAL SPECIFICATIONS Input: Power: Belt Speed: Belt Surface: Belt Size: Weight: 230-240V ~ 50Hz 850W 300-400m/min 75 x 140mm 75 x 533mm 3.1kg Belt Sander
More informationCORDLESS DRILL DRIVER
WHAT S IN THE BOX CORDLESS DRILL DRIVER 12V Ni-Cad INSTRUCTION MANUAL SPECIFICATIONS Input: 12V Chuck Size: 10mm Keyless No Load Speed: 0-550/min Torque Setting: 16 Max. Torque: 12Nm Battery: 1.2Ah Ni-Cad
More informationRADIAL TILE CUTTING MACHINE
KNOW YOUR PRODUCT RADIAL TILE CUTTING MACHINE 8W INDUCTION MOTOR 5MM CUTTING LENGTH - BLADE TILT DETACHABLE LASER INSTRUCTION MANUAL WARNING: Read all safety warnings and all instructions. Failure to follow
More information4-VOLT LITHIUM-ION AUTO-LOAD SCREWDRIVER w/led WORKLIGHT
SKU 241-1394 4-VOLT LITHIUM-ION AUTO-LOAD SCREWDRIVER w/led WORKLIGHT Operation Manual WARNING! Please read this manual before using this product. Failure to do so can result in serious injury. SAVE THIS
More informationTWIN MIXING DRILL INSTRUCTION MANUAL 1600W HIGH POWER IDEAL FOR MIXING CONCRETE, MORTAR, PAINT & ADHESIVES 2 SPEED GEARING Ø12 X 57CM PADDLE
KNOW YOUR PRODUCT TWIN MIXING DRILL 1600W HIGH POWER IDEAL FOR MIXING CONCRETE, MORTAR, PAINT & ADHESIVES 2 SPEED GEARING Ø12 X 57CM PADDLE INSTRUCTION MANUAL WARNING: Read all safety warnings and all
More informationDRILL DRIVER. 12V Lithium Ion WARRANTY INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au ZLDDS-012 WHAT S IN THE BOX
WHAT S IN THE BOX DRILL DRIVER 12V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Input: 12V Chuck Size: 10mm Keyless No Load Speed: 0-400 / 0-1500/min Torque Setting: 21 Max. Torque: 14Nm Weight: 1.2kg
More informationW6VB3 W8VB2. Handling instructions
Screw Driver Model W 6VM W 6V4 W 6VA4 W 6VB3 W 8VB2 Handling instructions W6VM W6V4 W6VA4 W6VB3 W8VB2 Note: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to
More informationCordless Line Trimmer
Cordless Line Trimmer 18 Volt Operation Manual 2 Year Replacement Warranty OZCLT18VA CAUTION: Read this operation manual before using this tool. 0309 To view the full range visit: www.ozito.com.au SPECIFICATIONS
More informationCORDLESS FINISHING GRINDER 18V Li-ion
WHAT S IN THE BOX CORDLESS FINISHING GRINDER 18V Li-ion INSTRUCTION MANUAL SPECIFICATIONS Input: 18V No Load Speed: 6000 / min Disc Diameter: 100mm (4 ) Spindle Size: M10 Battery Power: 1.3Ah Li-ion Charge
More informationInstruction Manual 4.0V Li-Ion Screwdriver. Part #: ECLIPSE ENTERPRISES, INC Chula Road, Amelia Court House, VA 23002, U.S.
Instruction Manual 4.0V Li-Ion Screwdriver Part #: 902-588 ECLIPSE ENTERPRISES, INC. 13302 Chula Road, Amelia Court House, VA 23002, U.S.A 2 3 Intended use Your ECLIPSE ENTERPRISES, INC. 902-588 screwdriver
More informationCORDLESS DRILL DRIVER 12V Lithium Ion
WHAT S IN THE BOX CORDLESS DRILL DRIVER 12V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Input: 12V Chuck Size: 10mm Keyless No Load Speed: 0-700/min Torque Setting: 17 Max. Torque: 10Nm Battery: 1.5Ah
More informationWET & DRY VACUUM INSTRUCTION MANUAL
WHAT S IN THE BOX Cordless Wet & Dry Vacuum WET & DRY VACUUM INSTRUCTION MANUAL SPECIFICATIONS Voltage: Suction Power: Tank Capacity: Flow Rate: Hose Diameter: IP Rating: Weight: ozito.com.au 18V 80mbar
More information10MM DRILL DRIVER INSTRUCTION MANUAL
STANDARD EQUIPMENT 10MM DRILL DRIVER INSTRUCTION MANUAL SPECIFICATIONS Input: 18V Chuck Size: 10mm Keyless No Load Speed: 0-550/min Torque Setting: 21 Max. Torque: 35Nm Weight: 0.9kg ozito.com.au 10mm
More information18V CORDLESS DRILL DRIVER CDT16180
18V CORDLESS DRILL DRIVER CDT16180 LX400 SAFETY INSTRUCTIONS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or
More informationCORDLESS PRUNING SAW INSTRUCTION MANUAL
WHAT S IN THE BOX Cordless Pruning Saw CORDLESS PRUNING SAW INSTRUCTION MANUAL SPECIFICATIONS Input: 18V Stroke Length: 20mm No Load Speed: 1500-2700spm Max. Cutting Diameter: 60mm (with clamping jaw)
More informationBENCH GRINDER MODEL NO: CBG6250
CBG6250 Bench Grinder.fm Page 1 Thursday, November 10, 2011 3:26 PM BENCH GRINDER MODEL NO: CBG6250 PART NO: 6500522 OPERATION & MAINTENANCE INSTRUCTIONS LS1111 CBG6250 Bench Grinder.fm Page 2 Thursday,
More informationCORDLESS ROTARY HAMMER DRILL INSTRUCTION MANUAL
WHAT S IN THE BOX CORDLESS ROTARY HAMMER DRILL INSTRUCTION MANUAL SPECIFICATIONS Input: 18V Chuck Type: SDS+ No Load Speed: 1,200/min Impact Power: 1.2J Impact Rate: 0-5,700bpm Max. Torque: 10Nm Weight
More informationCordless Line Trimmer
RLT6X RLT6B ORIGINAL INSTRUCTIONS Cordless Line Trimmer Important! It is essential that you read the instructions in this manual before assembling, maintaining and operating this machine. Subject to technical
More informationR18DDBL ORIGINAL INSTRUCTIONS. 18V Brushless Drill Driver
R18DDBL ORIGINAL INSTRUCTIONS 18V Brushless Drill Driver Important! It is essential that you read the instructions in this manual before assembling, operating and maintaining the product. Subject to technical
More informationCORDLESS GRASS TRIMMER KIT
WHAT S IN THE BOX CORDLESS GRASS TRIMMER KIT 18V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Voltage: Battery: Charge Time: No Load Speed: Max. Width of Cut: Weight: ozito.com.au 18V 1.5Ah Li-ion 3-5
More informationCordless Drill. 12V Li-Ion. LIR-012. To view the full range visit: Instruction Manual 3 Year Replacement Warranty
Cordless Drill 12V Li-Ion Instruction Manual 3 Year Replacement Warranty LIR-012! WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric
More informationSPECIFICATIONS MODEL NO. APR-012
SPECIFICATIONS MODEL NO. APR-012 Input power: Batteries: Charge time: No load air flow: Max. air pressure: Weight (tool only): 12V Battery 1 x 12V, 1.3Ah, Ni-Cad 3 5 hours 14 litres/min 160 PSI (1103kPa/11Bar)
More informationSPECIFICATIONS MODEL NO. CDL-018
SPECIFICATIONS MODEL NO. CDL-018 Battery power: 18V Charge time: 3 5 hours No load speed: 0 580/min Chuck type: Keyless 10mm Torque settings: 19 + 1 Batteries: 2 x 1.3Ah Lithium Ion Weight with 1 battery:
More informationCONSTANT PRESSURE PUMP
WHAT S IN THE BOX CONSTANT PRESSURE PUMP 8W INSTRUCTION MANUAL SPECIFICATIONS Motor: 8W Max. Flow Rate:, l/h Max. Lift: 8m Max. Head: 8m Inlet & Outlet:.mm ( BSP) Female Max. Delivery Pressure:.8 bar Water
More informationTOOLPRO 18V Li-Ion Brushless Impact wrench
TOOLPRO 18V Li-Ion Brushless Impact wrench Instruction Manual CIW180HB.9 After Sales Support FREE CALL 1300 889 028 EMAIL:salesau@positecgroup.com Important - Please read these instructions fully before
More informationKNOW YOUR PRODUCT SETUP & PREPARATION CORDLESS LAWN MOWER 1. Wheels 8. Upper Handle 2. Battery Cover 9. Lock-off Button 3. Battery Cover Securing Latc
WHAT S IN THE BOX Cordless Lawn Mower CORDLESS LAWN MOWER INSTRUCTION MANUAL SPECIFICATIONS Voltage: 18V x 2 Battery: 2.0Ah Li-ion Charge Time: 40min Cutting Diameter: 330mm Cutting Heights: 25-65mm (5
More informationATD V CORDLESS LITHIUM ION DRILL & DRIVER COMBO KIT Instruction Manual
ATD 10525 12V CORDLESS LITHIUM ION DRILL & DRIVER COMBO KIT Instruction Manual KNOW YOUR PRODUCT (DRILL) 1. Keyless chuck 2. Torque adjustment collar 3. Speed selector 4. Forward/reverse selector 5. Battery
More informationCORDLESS DRILL DRIVER 12V Lithium Ion
WHAT S IN THE BOX CORDLESS DRILL DRIVER 12V Lithium Ion INSTRUCTION MANUAL SPECIFICATIONS Input: 12V Chuck Size: 10mm Keyless No Load Speed: 0-350 / 0-1200/min Torque Setting: 19 Max. Torque: 15Nm Battery:
More informationCordless Hammer Drill Kit
Cordless Hammer Drill Kit 18 Volt Operation Manual 3 Year Replacement Warranty OZCD18V2A To view the full range visit: www.ozito.com.au 0109 SPECIFICATIONS MODEL NO. OZCD18V2A Battery power: 18V Charge
More informationROTATOR TM COMBI SAW 12V INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au WHAT S IN THE BOX. Cordless Combi Jigsaw. Blades. Charger.
WHAT S IN THE BOX ROTATOR TM COMBI SAW 12V INSTRUCTION MANUAL SPECIFICATIONS Input: No Load Speed: Stroke Length: Blade Fitment: Max. Cutting Capacity: Battery: Charge time: Weight: ozito.com.au 12V 600-2500spm
More information115MM ANGLE GRINDER INSTRUCTION MANUAL
WHAT S IN THE BOX Angle Grinder 115MM ANGLE GRINDER INSTRUCTION MANUAL SPECIFICATIONS Voltage: 18V No Load Speed: 8500/min Disc Diameter: 115mm (4 1/2 ) Spindle: M14 Weight: 1.8kg ozito.com.au Side Handle
More informationWHAT S IN THE BOX SANDER POLISHER. Sander Polisher 1100W. Assorted Discs INSTRUCTION MANUAL SPECIFICATIONS. ozito.com.au SPR-7100
WHAT S IN THE BOX SANDER POLISHER 1100W INSTRUCTION MANUAL SPECIFICATIONS Voltage: Power: No Load Speed: Disc Size: Sander Base Fitment: Weight: ozito.com.au 230-240V ~ 50Hz 1100W 1,000-3,500/min 180mm
More informationCat. No. M18 Cordless multi-tool. To reduce The risk of injury, user must read and understand operator's manual.
OPERATOR'S MANUAL Cat. No. M18 Cordless multi-tool To reduce The risk of injury, user must read and understand operator's manual. 2 General POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and
More informationElectric Chainsaw. 1800W Instruction Manual 2 Year Replacement Warranty. CSE-355 CAUTION: Read this instruction manual before using this tool.
Electric Chainsaw 1800W Instruction Manual 2 Year Replacement Warranty CSE-355 CAUTION: Read this instruction manual before using this tool. 0812 To view the full range visit: www.ozito.com.au TABLE OF
More informationBRUSHLESS LAWN MOWER ORIGINAL INSTRUCTIONS
STANDARD EQUIPMENT Brushless Lawn Mower BRUSHLESS LAWN MOWER ORIGINAL INSTRUCTIONS Safety Key SPECIFICATIONS Voltage: 18V Cutting Diameter: 300mm Cutting Heights: 30, 50 & 70mm No Load Speed: 3,300/min
More informationCORDLESS DRILL DRIVER 18V Li-ion
WHAT S IN THE BOX CORDLESS DRILL DRIVER 18V Li-ion INSTRUCTION MANUAL SPECIFICATIONS Input: 18V Chuck Size: 10mm Keyless No Load Speed: 0-350/0-1200/min Torque Setting: 19 + 1 Max. Torque: 22Nm Drilling
More informationCORDLESS ROTARY HAMMER DRILL INSTRUCTION MANUAL
WHAT S IN THE BOX CORDLESS ROTARY HAMMER DRILL INSTRUCTION MANUAL SPECIFICATIONS Input: 18V Chuck Type: SDS+ No Load Speed: 1,200/min Impact Power: 1.2J Impact Rate: 0-5,700bpm Max. Torque: 10Nm Weight
More informationAustralia
www.blackanddecker.com.au 2 5 3 1 4 WP1500K-XE Australia New Zealand Intended use Your Black & Decker sander has been designed for sanding and polishing wood, metal, plastics and painted surfaces. This
More informationBelt Sander JCB-BS950
Safety and operating manual Belt Sander JCB-BS950 ORIGINAL INSTRUCTIONS GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions
More informationCOMPACT DRILL DRIVER KIT INSTRUCTION MANUAL
WHAT S IN THE BOX COMPACT DRILL DRIVER KIT INSTRUCTION MANUAL Compact Drill Driver SPECIFICATIONS Input: 18V Chuck Size: 13mm Single Sleeve No Load Speed: 0-350 / 0-1,250/min Torque Setting: 18 Max. Torque:
More informationCordless Driver Drill
INSTRUCTION MANUAL Cordless Driver Drill MT064 MT065 003947 IMPORTANT: Read Before Using. ENGLISH (Original instructions) SPECIFICATIONS Model MT064 MT065 Steel 0 mm 3 mm Capacities Wood 25 mm 28 mm Wood
More information