Flat Deburring, Edge Rounding & Finishing

Transcription

1 Flat Deburring, Edge Rounding & Finishing NAUTILUS SERIES WET

2 NAUTILUS SERIES WET DEBURRING, EDGE ROUNDING & FINISHING MACHINES Nautilus Wet Deburring and Finishing Machines are designed for economically deburring, finishing, and/or edge rounding a wide variety of component parts made from either sheet metal or steel plate. Scotch Brite brush(es) ensure exceptional part results where the finish is critical. Available in one to four head configurations, and in 37 and 52-inch wide models. The Nautilus is designed to provide years of dependable service in the most demanding industrial applications. Made in USA. STANDARD FEATURES Modular design with docking ports for a variety of cartridge-style abrasive heads Conveyor bed is manufactured with inch thick steel plate and precision machined and to +/ tolerance to insure flatness Conveyor bed adjustment with 4 precision jacks, covered gears, roller bearing guides and direct linkage Electronic thickness adjustment with HMI/PLC control, color monitor and up to 50 presets Automatic self-aligning conveyor belt tracking system Electronic variable feed speed control with AC drive Articulating Arm Note: Articulating Arm is not included on Nautilus 1 Single Head models Cartridge-style belt head assembly with automatic abrasive belt tracking system with ultrasonic sensor Cartridge-style barrel brush head assembly with standard oscillating speeds of 250 strokes per minute Cartridge-style top brush head assembly with 10-inch diameter brushes or Scotch-Brite pads Belt head and brush head assemblies are handwheel adjusted Pinch rollers are spring-loaded Infeed conveyor section includes 2 vinyl covered rollers Infeed safety bar with over thickness limit switch Stainless steel collection pan and exterior doors Automatic parts dryer with Air Sonic air knife and regenerative blower Automatic paper bed filter Central lubrication point Electrical control panel with 24 volt DC circuit Made In USA ACCESSORIES Allen-Bradley HMI/PLC controls with color monitor Electronic vertical head positioning systems Electronic variable speed belt/brush control Special conveyor belts Sacrificial stainless steel conveyor bed cover Vacuum bed Automatic lubricating system Paper Bed Filter Includes filter media, clean tank, sludge bin, and clean return pump

3 Close Up Shots & Accessories Optional Allen Bradley HMI/PLC Infeed Conveyor Optional Vacuum Bed Automatic Parts Dryer Optional Allen-Bradley HMI/PLC to control thickness, feed speed, belt/brush RPM & brush oscillation speed Infeed conveyor extension with two (2) vinyl covered rollers Optional vacuum bed for short parts Automatic parts dryer with Air-Sonic air knife and regenerative blower Automatic Lubricating System Automatic Conveyor Belt Tracking Automatic Abrasive Belt Tracking Top Brushes Low maintenance AC drive with variable line speed from 5-40 fpm Conveyor bed with automatic belt tracking system Self-aligning, abrasive belt tracking system Top brushes for deburring and edge rounding Cartridge-Style Abrasive Heads FIXED BELT HEAD (FB) ADJUSTABLE BELT HEAD (AB) BARREL BRUSH HEAD (BB) TOP BRUSH HEAD (TB)

4 Typical Configurations Performance Data & Specifications SINGLE HEAD (FB/AB) TWO HEAD (AB-AB) DESCRIPTION 37 INCH 52 INCH Maximum Panel Width 36 inches (914 mm) 51 inches (1295 mm) Working Thickness - Minimum determined by material - Maximum in (0.9 mm) in (0.9 mm) Minimum Part Length - w/belt head assemblies - w/barrel brush assemblies - w/top brush assemblies 9.75 inches (247 mm) 12 inches (305 mm) 12.5 inches (318 mm) 9.75 inches (247 mm) 14 inches (355 mm) 12.5 inches (318 mm) Belt Head Assembly (FB Fixed/AB Adjustable)- - Contact drum diameter - Drum speed - Motor Size - Abrasive Belt Size 2750 SFPM 20 hp 37 X 75 inches 8 inches (203 mm) 3660 SFPM 25 hp 52 X 75 inches THREE HEAD (AB-AB-BB) THREE HEAD (FB-BB-BB) Barrel Brush Head Assembly (BB) - Minimum Brush Diameter - Maximum Brush Diameter Brush - Inside Diameter - Option 1 - Option 2 Brush Speed Motor Size Oscillating Speed 6.75 inches (172 mm) 3 inches (76 mm) 5.75 inches (146 mm) 3800 SFPM 15 HP 250 SPM 7.5 inches (190 mm) 12 inches (305 mm) 5.75 inches (146 mm) 3800 SFPM 20 HP 250 SPM Top Brush Head Assembly - Brush/Pad Diameter - Number of Brushes - Brush Speed - Motor Size (each) - Oscillating Speed 4 each 1200 SFPM 2 HP 30 SPM 5 each 1200 SFPM 2 HP 30 SPM THREE HEAD (FB-TB-BB) FOUR HEAD (AB-AB-BB-BB) Pinch Roller Diameter 2.15 inches (55 mm) 2.75 inches (70 mm) Feed Speed 6-40 FPM 6-40 FPM Automatic Paper Bed Filter One (1) Head Models Two (2) Head Models Three (3) Head Models Four (4) Head Models 26 GPM 80 GALLONS 39 GPM 120 GALLONS 26 GPM 80 GALLONS 80 GPM 220 GALLONS LEGEND FB Fixed Belt AB Adjustable Belt BB Barrel Brush TB Top Brush Automatic Parts Dryer One (1) Head Models Two (2) Head Models Three (3) & Four (4) Head Models Compressed Air Requirements 80 5 CFM 80 5 CFM Electrical Requirements TBD TBD

5 YOUR REQUIREMENTS DRIVE OUR BUSINESS. Midwest Automation is a family owned U.S. manufacturing company located in Minneapolis Minnesota. For companies who care where the products they buy are made, it will come as no surprise that buying American is not as easy as it used to be. If you look closely you will discover that many of the machines represented to be American made are in fact imported from foreign countries. For over 60 years, Midwest Automation has manufactured industrial machinery for the woodworking, composite panel and metalworking industries using U.S. labor, and locally available components whenever possible. Our extensive application knowledge, coupled with creative machine designs, allows us to provide unique and reliable solutions that improve your manufacturing processes, supported by local parts and service. If you are looking for an industrial machinery manufacturer with real application expertise, contact Midwest Automation today. Manufacturing results since th Avenue South, Minneapolis, MN phone Midwest Automation LLC