TECHNICAL GUIDE LISTED

Transcription

1 E T I I I R P I T G TECHNICAL GUIDE SPLIT-SYSTEM AIR CONDITIONERS 12 SEER MODELS: H*BC-F018 THRU 060 (1.5 THRU 5 NOMINAL TONS, 1 PH)H*BC- (T,W)036 THRU 060 (3 THRU 5 NOMINAL TONS, 3 PH) LISTED ISO 9001 Certified Quality Management System CERTIFICATION APPLIES ONLY WHEN THE COMPLETE SYSTEM IS LISTED WITH ARI. Due to continuous product improvement, specifications are subject to change without notice. Visit us on the web at for the most up-to-date technical information. Additional rating information can be found at U R A C T MA N U F R C E UN I R T I C ER T A R I A RY F F I E D E Q U I C A T T S A T ON O T M E N S A R I AI E CT N D A R R - C D AS ONDI ON S 2 O I C 1 0 OM P NI N G OF L Y N I W IT H Rev. C (0505) DESCRIPTION The 12 SEER Series condensing unit is the outdoor part of a versatile system of air conditioning. It is designed to be custom-matched with one of UPG s complete line of evaporator sections, each designed to serve a specific function. Matching Air Handlers are available for upflow, downflow or horizontal applications to provide a complete system. Electric Heaters are available if required. Add-On coils are available for use with upflow, downflow or horizontal furnaces and air handlers. WARRANTY Single Phase Units: 5-year limited parts warranty. 10-year limited compressor warranty. Three Phase Units: 1-year limited parts warranty. 5-year limited compressor warranty. FEATURES QUALITY CONDENSER COILS - The coil is constructed of enhanced copper tube and aluminum fins. COIL PROTECTION - Coils are protected from damage by a polymer mesh applied between the coil face, and a PVC coated steel coil guard. PROTECTED COMPRESSOR - The compressor is internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor. DURABLE FINISH - The cabinet is made of pre-painted steel. The pre-treated galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted textured champagne finish insure less fading when exposed to sunlight. LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. Discharge line heat exchanger knockouts are provided, if required. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof. TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications. LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise up away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. LOW MAINTENANCE - Long life permanently lubricated motor-bearings need no annual servicing. EASY SERVICE ACCESS - Fully exposed refrigerant connections, a single panel covering the electrical controls and the molex plug in the control box connecting the condenser fan, make for easy servicing of the unit. SECURED SERVICE VALVES - Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging. U.L. and C.U.L. listed - approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240. FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

2 Physical and Electrical Data - 1 Phase MODEL HBBC-F018S HBBC-F024S HBBC-F030S HBBC-F036S HBBC-F042S HBBC-F048S HDBC-F060S Unit Supply Voltage 208/ Normal Voltage Range 187 to 252 Minimum Circuit Ampacity Max. Overcurrent Device Amps Compressor Type 3 Recip Inertia Recip Recip Scroll B Recip Scroll B Rated Load Compressor Amps Locked Rotor Crankcase Heater No No No Yes No No No Fan Motor Amps Rated Load Fan Diameter Inches Fan Motor Rated HP 1/12 1/12 1/15 1/4 1/4 1/4 1/4 Nominal RPM 1,100 1, Nominal CFM 2,000 2,000 2,300 3,300 3,300 3,300 3,450 Face Area Sq. Ft Coil Rows Deep Fin / Inches Liquid Line OD 3/8 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line OD 3/4 3/4 3/4 3/4 7/8 7/8 1-1/8 Unit Charge (Lbs. - Oz.) Charge Per Foot, Oz Operating Weight Lbs PHYSICAL AND ELECTRICAL DATA - 3 Phase MODEL HABC-T036S HABC-T048S HABC-T060S HABC-W036S HABC-W048S HABC-W060S Unit Supply Voltage 208/ Normal Voltage Range to to 504 Minimum Circuit Ampacity Max. Overcurrent Device Amps Compressor Type Inertia Inertia Scroll Inertia Inertia Scroll Rated Load Compressor Amps Locked Rotor Crankcase Heater No No No No No No Fan Motor Amps Rated Load Fan Diameter Inches Fan Motor Rated HP 1/4 1/4 1/4 1/4 1/4 1/4 Nominal RPM Nominal CFM 3,300 3,300 3,400 3,300 3,300 3,400 Face Area Sq. Ft Coil Rows Deep Fin / Inches Liquid Line OD 3/8 3/8 3/8 3/8 3/8 3/8 Vapor Line OD 3/4 7/8 1-1/8 3/4 7/8 1-1/8 Unit Charge (Lbs. - Oz.) Charge Per Foot, Oz Operating Weight Lbs Rated in accordance with ARI Standard 110, utilization range A. 2. Dual element fuses or HACR circuit breaker. 3. All scrolls listed with a superscript B are Bristol scrolls. All scrolls listed with a superscript C are Copeland scrolls. 4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value. 2 Unitary Products Group

3 Additional R-22 Charge / Orifice Size for Various Matched Systems - 1 Phase Outdoor Unit HBBC-F018S HBBC-F024S HBBC-F030S HBBC-F036S HBBC-F042S HBBC-F048S HCBC-F060S Unit Orifice (s) Factory R-22 Charge, lbs-oz Indoor Coil 5 Coil Orifice 4 Orifice or TXV Kit 2 - Additional Charge, Oz. 3 G2FD024(S,H)14, G2FD030(S,H) G2FD035(S,H) G2FD036(S,H) G2FD036(S,H) G2FD042(S,H) G2FD046(S,H) G2FD048(S,H)21, G2FD060(S,H) G2FD061H G1HA024H G1HA024H14(T) TXV G1HA036H G1HA036H14(T) TXV G1HA036H G1HA036H17(T) TXV G1HA048H G1HA048H21(T) TXV G1HA060H G1HA060H24(T) TXV G1HD G1HD G1HD G1HD G1FA/G1UA024S14,17(T) G1FA/G1UA030S14(T) G1FA/G1UA036S14(T) G1FA/G1UA036S17,21(T) G1FA/G1UA048S17(T) G1FA/G1UA048S21(T) G1FA/G1UA060S21,24(T) G1NA030S17K G1NA030S21M See notes on Page 4. Unitary Products Group 3

4 Additional R-22 Charge / Orifice Size for Various Matched Systems (Continued)- 1 Phase Outdoor Unit HBBC-F018S HBBC-F024S HBBC-F030S HBBC-F036S HBBC-F042S HBBC-F048S HCBC-F060S Unit Orifice (s) Factory R-22 Charge, lbs-oz Indoor Coil 5 Coil Orifice 4 Orifice or TXV Kit 2 - Additional Charge, Oz. 3 G1NA036S17L 63 G1NA048S21D 78 G1NA048S24P 63 G1NA060S24T 78 G1NF024SOF 63 G1NF036SOF 67 G1NF048SOF 78 G1NF060SOF 87 F(2,3)RP024N,H06(T) 61 F(2,3)RP030N06(T) 65 F(2,3)RP036N06(T) 75 F(2,3)RP042N06(T) 78 F(2,3)FP048N06(T) 84 F(2,3)FP060N06(T) 90 F(2,3)FV060N06(T) 90 FOOTNOTES: PROCEDURES: These orifices are factory mounted in the flow control device of each indoor coil and must be removed for TXV installation. 2. A TXV kit must be used with these coils to obtain system performance. (701,702,703 indicates 1TV07...series). 3. Systems matched with furnaces or air handlers not equipped with blower-off delays, may require blower Time Delay Kit #6918A These orifices are factory mounted in the flow control device of each indoor coil. A TXV is factory mounted if the model number has a (T) suffix. 5. This TXV is factory mounted in indoor coils, if the model number has a (T) suffix. 1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and for 15 feet of interconnecting line tubing. 2. Verify the orifice size and additional charge required for specific evaporator coil in the system using the above table. 3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above. 4. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaporator + adder for line set. 5. If the orifice in the evaporator was changed, verify the evaporator nameplate has been marked with the correct orifice size. 4 Unitary Products Group

5 Additional R-22 Charge / Orifice Size for Various Matched Systems - 3 Phase Outdoor Unit HABC-T,W036S HABC-T,W048S HABC-T,W060S Unit Orifice (s) 1 Factory R-22 Charge, lbs-oz Indoor Coil Coil Orifice TVX Kit 2 = Additional Charge, Oz 3 G2FD035(S,H) G2FD036(S,H)17, G2FD042(S,H) G2FD046(S,H) G2FD048(S,H)21, G2FD060(S,H) G2FD061H G1FA/G1UA036S G1FA/G1UA036S17, G1FA/G1UA048S G1FA/G1UA048S G1FA/G1UA060S21, G1NA036S17L G1NA048S21D G1NA048S24P G1NA060S24T G1NF036SOF G1NF048SOF G1NF060SOF G1HD G1HD G1HD FOOTNOTES: 1. These orifices are factory mounted in the flow control device of each indoor coil and must be removed for TXV installation. 2. A TXV kit must be used with these coils to obtain system performance. (701,702,703 indicates 1TV07...series). 3. Systems matched with furnaces or air handlers not equipped with blower-off delays, may require blower Time Delay Kit #6918A5011. PROCEDURES: 1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and for 15 feet of interconnecting line tubing. 2. Verify the orifice size and additional charge required for specific evaporator coil in the system using the above table. 3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above. 4. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaporator + adder for line set. 5. If the orifice in the evaporator was changed, verify the evaporator nameplate has been marked with the correct orifice size. Unitary Products Group 5

6 COOLING CAPACITY - With Air Handler Coils AIR HANDLER UNIT MODEL COIL 1 COOLING MODEL ELECTRIC 2 RATED NET MBH W MODEL HEAT KW CFM TOTAL SENS. 1 PH 12 SEER AC WITH N1AH / G2FD SEER W/O TXV 4. To meet R=4.2 insulation requirements, substitute F2FP for F2RP, and F2FC for F2RC. models. All ratings remain the same. 5. FG8, FG9, and FL8 furnaces and F2RP / F2RC air handlers have B.O.D (Blower on Delay) standard. - = Not applicable. SEER WITH TXV 3 HBBC-F018S N1AHB0806 2,5,8,10 17 G2FD024(S,H) HBBC-F024S N1AHB0806 2,5,8,10 17 G2FD024(S,H) N1AHB0806 2,5,8,10 17 G2FD030(S,H) HBBC-F030S N1AHB1206 2,5,8,10 17 G2FD030(S,H) N1AHB1206 2,5,8,10 17 G2FD036(S,H) HBBC-F036S N1AHB1206 5,8,10,15,19 17 G2FD036(S,H) N1AHB1206 5,8,10,15,19 17 G2FD046(S,H) HBBC-F042S N1AHC1606 5,8,10,15,20 21 G2FD042(S,H) N1AHC1606 5,8,10,15,20 21 G2FD048(S,H) N1AHC1606 5,8,10,15,20 21 G2FD048(S,H) HBBC-F048S N1AHD2006 8,10,15,20,25,30 24 G2FD060(S,H) N1AHD2006 8,10,15,20,25,30 24 G2FD061H HCBC-F060S N1AHD2006 8,10,15,20,25,30 24 G2FD060(S,H) N1AHD2006 8,10,15,20,25,30 24 G2FD061H PH 12 SEER AC WITH N1AH / G2FD N1AHB1246 5,8,10,15,18 17 G2FD036(S,H) HABC-(T,W)036S N1AHB1246 5,8,10,15,18 17 G2FD046(S,H) N1AHC1646 5,8,10,15,18 21 G2FD048(S,H) HABC-(T,W)048S N1AHD2046 8,10,15,20,25,30 24 G2FD060(S,H) N1AHD2046 8,10,15,20,25,30 24 G2FD061H HABC-(T,W)060S N1AHD2046 8,10,15,20,25,30 24 G2FD060(S,H)24(T) N1AHD2046 8,10,15,20,25,30 24 G2FD061H PH 12 SEER / N1VS - VARIABLE SPEED HBBC-F018S N1VSB12 10,15,18 17 G2FD024(S,H) HBBC-F024S N1VSB12 10,15,18 17 G2FD024(S,H) N1VSB12 10,15,18 17 G2FD036(S,H) N1VSB12 10,15,18 17 G2FD036(S,H) HBBC-F030S N1VSB12 10,15,18 17 G2FD046(S,H) N1VSB12 10,15,18 17 G2FD046(S,H) N1VSB12 10,15,18 17 G2FD036(S,H) HBBC-F036S N1VSB12 10,15,18 17 G2FD046(S,H) N1VSC16 10,15,18 21 G2FD048(S,H) HBBC-F042S N1VSC16 10,15,18 21 G2FD048(S,H) N1VSC16 10,15,18 21 G2FD048(S,H) N1VSC16 10,15,18 21 G2FD048(S,H) HBBC-F048S N1VSD20 10,15,18,30 24 G2FD060(S,H) N1VSD20 10,15,18,30 24 G2FD061H HCBC-F060S N1VSD20 10,15,18,30 24 G2FD060(S,H) N1VSD20 10,15,18,30 24 G2FD061H PH 12 SEER AC / F2RP / RC / FC 4, 5 HBBC-F018S F2RC/F2FC024 5,8, F2RP/F2FP024 5,8, F2RC/F2FC024 5,8, HBBC-F024S F2RC/F2FC030 5,8,10, F2RP/F2FP024 5,8, F2RP/F2FP030 5,8,10, F2RC/F2FC030 5,8,10, HBBC-F030S F2RC/F2FC036 5,8,10, F2RP/F2FP030 5,8,10, F2RP/F2FP036 5,8,10,15, F2RC/F2FC036 5,8,10, HBBC-F036S F2RP/F2FP036 5,8,10,15, F2RP/F2FP042 5,8,10, F2FP048 5,8,10,15,20, HBBC-F042S F2RP/F2FP042 5,8,10, F2FP048 5,8,10,15,20, F2FP048 5,8,10,15,20, HBBC-F048S F2FP060 5,8,10,15,20, F2FV060 8,10,15,20, HCBC-F060S F2FP060 5,8,10,15,20, F2FV060 8,10,15,20, Rated in accordance with DOE test procedures (Federal Register and ) and ARI Standards 210. Cooling MBH based on 80 F entering air temperature, 50% RH, and rated air flow. EER (Energy Efficiency Ratio) is the total cooling output in BTU s at a 95 F outdoor ambient divided by the total electric power in watt-hours at those conditions. SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU s during a normal annual usage period for cooling divided by the total electric power input in watt-hours during the same period. 1. G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number. 2. Single phase units require single phase 2HK heaters. Three phase units require three phase 2HK heaters. 3. TXV = Thermal Expansion Valve kit required. Use 1TV700 series kit. 6 Unitary Products Group EER

7 COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils FURNACE** COOLING UNIT MODEL COIL CFM RANGE NET MBH W MODEL RATED CFM SEER (Min.-max.) W/O TXV SEER + TXV 1 EER TOTAL SENS. HBBC-F018S HBBC-F024S HBBC-F030S For Notes See Page ,17 G1FA024S14, * G1HA024H * G1HA024H14T * G1HD * G1NA030S17K * G1NA030S21M * ,17 G1UA024S14, * ,17 G2FD024(S,H)14, * G2FD030(S,H) * G2FD035(S,H) * ,17 G1FA024S14, * G1FA030S * G1FA036S * ,21 G1FA036S17, * G1HA024H * G1HA024H14T * G1HA036H G1HD * G1HD * G1NA030S17K * G1NA030S21M * ,17 G1UA024S14, * G1UA030S * G1UA036S * ,21 G1UA036S17, * ,17 G2FD024(S,H)14, * G2FD030(S,H) * G2FD035(S,H) * G2FD036(S,H) * G1FA030S * G1FA036S * ,21 G1FA036S17, * G1FA048S * G1FA048S * G1HA036H * G1HA036H * G1HA036H * G1HA036H17T * G1HD * G1NA030S17K * G1NA030S21M * G1NA036S17L * G1UA030S * G1UA036S * ,21 G1UA036S17, * G1UA048S * G1UA048S * G2FD030(S,H) * G2FD035(S,H) * G2FD036(S,H) * G2FD036(S,H) * G2FD042(S,H) * G2FD046(S,H) * Unitary Products Group 7

8 COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils (Continued) FURNACE** COOLING COIL UNIT MODEL CFM RANGE NET MBH W MODEL SEER RATED CFM (Min.-max.) W/O TXV SEER + TXV 1 EER TOTAL SENS. HBBC-F036S HABC-(T,W)036S HBBC-F042S For Notes See Page G1FA036S * ,21 G1FA036S17, * G1FA048S * G1FA048S * G1HA036H * G1HA036H * G1HA036H * G1HA036H17T * G1HA048H * G1HA048H21T G1HD * G1HD * G1NA036S17L * G1NA048S21D * G1UA036S * ,21 G1UA036S17, * G1UA048S * G1UA048S * G1NA048S21D * G2FD035(S,H) * G2FD036(S,H) * G2FD036(S,H) * G2FD042(S,H) * G2FD046(S,H) * ,24 G2FD048(S,H)21, * G1FA036S ,21 G1FA036S17, G1FA048S G1HD G1HD G1NA036S17L G1NA048S21D G1UA036S ,21 G1UA036S17, G1UA048S G2FD035(S,H) G2FD036(S,H) G2FD036(S,H) G2FD042(S,H) G2FD046(S,H) ,24 G2FD048(S,H)21, G1FA048S * G1FA048S ,24 G1FA060S21, G1HA048H * G1HA048H21T G1HD G1NA048S21D * G1UA048S * G1UA048S ,24 G1UA060S21, * G2FD042(S,H) * G2FD046(S,H) * ,24 G2FD048(S,H)21, Unitary Products Group

9 HBBC-F048S HABC-(T,W)048S HDBC-F060S HABC-(T,W)060S TXV = Use 1TV700 Series Kit. *Requires 2FD Blower Time Delay unless a standard furnace is equipped with one. ** Refer to Quick Selection Chart for specific furnace match-up Rev. C (0505) COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils (Continued) FURNACE** COOLING COIL UNIT MODEL CFM RANGE NET MBH W MODEL SEER RATED CFM (Min.-max.) W/O TXV SEER + TXV 1 EER TOTAL SENS. 17 G1FA048S * G1FA048S * ,24 G1FA060S21, * G1HA048H * G1HA048H21T * G1HA060H * G1HA060H24T * G1HD * G1HD * G1NA048S21D * G1UA048S * G1UA048S * ,24 G1UA060S21, * G2FD046(S,H) * ,24 G2FD048(S,H)21, * G2FD060(S,H) * G2FD061H * G1FA048S G1FA048S ,24 G1FA060S21, G1HD G1HD G1NA048S21D G1UA048S G1UA048S ,24 G1UA060S21, G2FD046(S,H) ,24 G2FD048(S,H)21, G2FD060(S,H) G2FD061H G1FA060S21(T) G1HD G1NA060S24T G1UA060S21(T) G2FD060(S,H)24(T) G2FD061H G1HA60S24(T) ,24 G1FA060S21, G1HA060H24T * G1HD G1NA060S24T * ,24 G1UA060S21, G2FD060(S,H) G2FD061H Unitary Products Group 9

10 COOLING CAPACITY - With Variable Speed Furnaces UNIT MODEL COOLING VARIABLE SPEED FURNACE MODEL COIL MODEL 1 W RATED NET MBH SEER SEER CFM TOTAL SENS. W/O TXV + TXV 2 EER 1 PH 12 SEER AC - VARIABLE SPEED 3 G8V***12UHA/(F,L)L8V***A12UH G1FA024S G8V***12UHA/(F,L)L8V***A12UH G2FD024(S,H) HBBC-F018S G9V***12DHB G2FD024(S,H) G9V***12UPB G1FA024S G9V***12UPB G2FD024(S,H) G8V***12UHA/(F,L)L8V***A12UH G1FA024S G8V***12UHA/(F,L)L8V***A12UH G2FD024(S,H) HBBC-F024S G9V***12DHB G2FD024(S,H) G9V***12UPB G1FA024S G9V***12UPB G2FD024(S,H) G8V***12UHA/(F,L)L8V***A12UH G1FA030S G8V***12UHA/(F,L)L8V***A12UH G2FD035(S,H) G8V***16UHB/(F,L)L8V***B16UH G1FA036S G8V***16UHB/(F,L)L8V***B16UH G2FD030(S,H) HBBC-F030S G9V***12DHB G2FD030(S,H) G9V***12UPB G1FA036S G9V***12UPB G2FD030(S,H) G9V***16UPC G1FA036S G9V***16UPC G2FD036(S,H) G8V***12UHA/(F,L)L8V***A12UH G1FA036S G8V***12UHA/(F,L)L8V***A12UH G2FD035(S,H) G8V***16UHB/(F,L)L8V***B16UH G1FA036S G8V***16UHB/(F,L)L8V***B16UH G2FD036(S,H) G8V***20UHC/(F,L)L8V***C20UH G1FA036S G8V***20UHC/(F,L)L8V***C20UH G2FD036(S,H) HBBC-F036S G9V***12DHB G2FD036(S,H) G9V***12UPB G1FA036S G9V***12UPB G2FD036(S,H) G9V***16UPC G1FA036S G9V***16UPC G2FD036(S,H) G9V***20UPC G1FA048S G9V***20UPC G2FD042(S,H) G9V***20UPD G2FD048(S,H) G8V***12UHA/(F,L)L8V***A12UH G1FA036S G8V***12UHA/(F,L)L8V***A12UH G2FD035(S,H) G8V***16UHB/(F,L)L8V***B16UH G1FA036S G8V***16UHB/(F,L)L8V***B16UH G2FD036(S,H) G8V***20UHC/(F,L)L8V***C20UH G1FA036S G8V***20UHC/(F,L)L8V***C20UH G2FD036(S,H) HABC-(T,W)036S G9V***12UPB G1FA036S G9V***12UPB G2FD036(S,H) G9V***16UPC G1FA036S G9V***16UPC G2FD036(S,H) G9V***20UPC G1FA048S G9V***20UPC G2FD042(S,H) G9V***20UPD G2FD048(S,H) G8V***16UHB/(F,L)L8V***B16UH G1FA048S G8V***20UHC/(F,L)L8V***C20UH G1FA048S HBBC-F042S G9V***20DHD G2FD048(S,H) G9V***16UPC G1FA048S G9V***20UPD G1FA060S G9V***20UPD G2FD048(S,H) For Notes See Page Unitary Products Group

11 COOLING CAPACITY - With Variable Speed Furnaces UNIT MODEL HBBC-F048S HABC-(T,W)048S HDBC-F060S HABC-(T,W)060S VARIABLE SPEED FURNACE MODEL COIL MODEL 1 W Rev. C (0505) TOTAL SENS. G8V***20UHC/(F,L)L8V***C20UH G1FA048S G8V***20UHC/(F,L)L8V***C20UH G2FD048(S,H) G9V***20DHD G2FD048(S,H) G9V***16UPC G1FA048S G9V***16UPC G2FD048(S,H) G9V***20UPC G1FA048S G9V***20UPC G2FD048(S,H) G9V***20UPD G1FA060S G9V***20UPD G2FD048(S,H) G9V***20UPD G2FD060(S,H) G8V***20UHC/(F,L)L8V***C20UH G1FA048S G8V***20UHC/(F,L)L8V***C20UH G2FD048(S,H) G9V***16UPC G1FA048S G9V***16UPC G2FD048(S,H) G9V***20UPC G1FA048S G9V***20UPC G2FD048(S,H) G9V***20UPD G1FA060S G9V***20UPD G2FD048(S,H) G9V***20UPD G2FD060(S,H) (G,L)8V***20UHD G1FA/G1UA060S21(T) (G,L)8V***20UHD G2FD060(S,H)24(T) (G,L)8V***20UHD G2FD061H G9V***20UPC G1FA/G1UA060S21(T) G9V***20UPC G2FD060(S,H)24(T) G9V***20UPC G2FD061H G9V***20UPD G1FA/G1UA060S24(T) G9V***20UPD G2FD060(S,H)24(T) G9V***20UPD G2FD061H G9V***20DHC G2FD060(S,H)24(T) G9V***20DHC G2FD061H G9V***20DHC G1HA60H24(T) G9V***20DHC G1HD G9V***20DHD G2FD060(S,H)24(T) G9V***20DHD G2FD061H G9V***20UHD G1HA60H24(T) G9V***20UHD G1HD (F,L)L8V***C20UH G1FA/G1UA060S21(T) (F,L)L8V***C20UH G2FD060(S,H)24(T) (F,L)L8V***C20UH G2FD061H G9V***20DHD G2FD060(S,H) G9V***20UPC G1FA060S G9V***20UPD G1FA060S G9V***20UPD G2FD060(S,H) G9V***20UPD G2FD061H G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number. 2. TXV = Use 1TV700 Series Kit. 3. Variable speed furnaces have B.O.D (Blower on Delay) standard. RATED CFM COOLING NET MBH SEER W/O TXV SEER + TXV 2 EER Unitary Products Group 11

12 ACCESSORIES* All dimensions are in inches. They are subject to change without notice. Certified dimensions will be provided upon request. DIMENSIONS - 1 Phase Unit Model Dimensions (Inches) A 1 1. Including Fan Guard. * Expander fitting required for 1-1/8 line set. Refrigerant Connection Line Size B C Liquid Vapor / / / /8 * DIMENSIONS - 3 Phase Unit Model A Dimensions (Inches) Refrigerant Connection Line Size A 1 B C Liquid Vapor /8 3/ /8 7/ /8 1-1/8 * B C Refer to Price Manual for specific model numbers. Hard Start Kit - Provides increased starting torque for areas with low voltage. Compressor Blanket - Designed to further reduce the normal compressor operating sound. Refer to price pages for specific match-ups. Off Cycle Timer Delay - Provides a 5-minute off cycle to prevent rapid recycling of the compressor. Room Thermostats - A wide selection of compatible thermosets are available to provide optimum performance and features for any installation. 1 Heat Stage only, manual, mechanical thermostat. Add subbase for 1H/1C. 1H/1C, manual change-over electronic non-programmable thermostat. 1H/1C, auto/manual changeover, electronic programmable, deluxe 7-day, thermostat. 1H/1C, auto/manual changeover, electronic programmable. * For the most current accessory information, refer to the price book or consult factory. SOUND POWER RATINGS UNIT MODEL (dba)* * Rated in accordance with ARI Standards. 1. Including Fan Guard. * Reducer Required 12 Unitary Products Group

13 TYPICAL INSTALLATION 60 OVERHEAD CLEARANCE MINIMUM 18 SERVICE ACCESS CLEARANCE ON ONE SIDE WEATHERPROOF DISCONNECT SWITCH THERMOSTAT TO FURNACE OR AIR HANDLER TERMINAL BLOCK NEC CLASS 1 WIRING NEC CLASS 2 WIRING 10 CLEARANCE COIL AREA TO INDOOR COIL NOTE: ALL OUTDOOR WIRING MUST BE WEATHERPROOF. SEAL OPENING(S) WITH PERMAGUM OR EQUIVALENT CONTROL ACCESS PANEL TYPICAL FIELD WIRING - 1 Phase Application ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES POWER WIRING 208/ VOLT CONTROL WIRING MINIMUM 18 GA. WIRE (NEC CLASS 2) C Y R G W POWER WIRING CONTROL WIRING FACTORY WIRING FURNACE OR AIR HANDLER TERMINAL BLOCK GND. LUG CONTACTOR TERMINALS COIL Y R G W * * TERMINAL W IS ONLY REQUIRED ON SYSTEMS WITH HEAT. CONDENSING UNIT ALL OUTDOOR WIRING MUST BE WEATHERPROOF. ROOM THERMOSTAT USE COPPER CONDUCTORS ONLY. TYPICAL FIELD WIRING - 3 Phase Application ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES POWER WIRING 208/ VOLT CONTROL WIRING MINIMUM 18 GA. WIRE (NEC CLASS 2) POWER WIRING CONTROL WIRING FACTORY WIRING FURNACE OR AIR HANDLER TERMINAL BLOCK GND. LUG CONTACTOR TERMINALS COIL * TERMINAL W IS ONLY REQUIRED ON SYSTEMS WITH HEAT. C Y R G W * Y R G W CONDENSING UNIT ROOM THERMOSTAT ALL OUTDOOR WIRING MUST BE WEATHERPROOF. USE COPPER CONDUCTORS ONLY. Unitary Products Group 13

14 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSING ENTERING AIR TEMPERATURE HBBC-F018S G1FA024S14,17 IDCFM ID DB ( F) ID WB ( F) T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW F2RC/F2FC F2RP/F2FP N1AHB0806 G2FD024(S,H)14, N1VSB12 G2FD024(S,H) G1HD G1NA030S17K G1NA030S21M G1UA024S14, G2FD024(S,H)14, G2FD030(S,H) G2FD035(S,H) Variable Speed Furnace Coil T.C. S.C. KW G8V***12UHA G1FA024S G8V***12UHA G2FD024(S,H) G9V***12DHB G2FD024(S,H) G9V***12UPB G1FA024S G9V***12UPB G2FD024(S,H) Unitary Products Group

15 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSING ENTERING AIR TEMPERATURE HBBC-F024S G1FA036S17,21 IDCFM ID DB ( F) ID WB ( F) T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW F2RP/F2FP F2RP/F2FP F2RC/F2FC F2RC/F2FC N1AHB0806 G2FD024(S,H) N1AHB0806 G2FD030(S,H) N1VSB12 G2FD024(S,H) N1VSB12 G2FD036(S,H) G1FA024S14, G1FA030S G1FA036S G1HD G1HD G1NA030S17K G1NA030S21M G1UA024S14, G1UA030S G1UA036S G1UA036S17, G2FD024(S,H)14, G2FD030(S,H) G2FD035(S,H) G2FD036(S,H) Variable Speed Furnace Coil T.C. S.C. KW G8V***12UHA G1FA024S G8V***12UHA G2FD024(S,H) G9V***12DHB G2FD024(S,H) G9V***12UPB G1FA024S G9V***12UPB G2FD024(S,H) Unitary Products Group 15

16 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSING ENTERING AIR TEMPERATURE HBBC-F030S G1FA036S17,21 IDCFM ID DB ( F) ID WB ( F) T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW F2RP/F2FP F2RP/F2FP F2RC/F2FC F2RC/F2FC N1AHB1206 G2FD030(S,H) N1AHB1206 G2FD036(S,H) N1VSB12 G2FD036(S,H) N1VSB12 G2FD046(S,H) G1FA030S G1FA036S G1FA048S G1FA048S G1HD G1NA036S17L G1NA030S17K G1NA030S21M G1UA030S G1UA036S G1UA036S17, G1UA048S G1UA048S G2FD030(S,H) G2FD035(S,H) G2FD036(S,H) G2FD036(S,H) G2FD042(S,H) G2FD046(S,H) Variable Speed Furnace Coil T.C. S.C. KW G8V***12UHA G1FA030S G8V***12UHA G2FD035(S,H) G8V***16UHB G1FA036S G8V***16UHB G2FD030(S,H) G9V***12DHB G2FD030(S,H) G9V***12UPB G1FA036S G9V***12UPB G2FD030(S,H) G9V***16UPC G1FA036S G9V***16UPC G2FD036(S,H) Unitary Products Group

17 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSING ENTERING AIR TEMPERATURE HBBC-F036S G1FA048S21 IDCFM ID DB ( F) ID WB ( F) T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW F2RC/F2FC F2RP/F2FP F2RP/F2FP F2FP N1VSB12 G2FD036(S,H) N1VSB12 G2FD046(S,H) N1VSC16 G2FD048(S,H) N1AHB1206 G2FD036(S,H) N1AHB1206 G2FD046(S,H) G1FA036S17, G1FA036S G1FA048S G1HD G1HD G1NA048S21D G1NA036S17L G1UA036S17, G1UA036S G1UA048S G1UA048S G2FD035(S,H) G2FD036(S,H) G2FD036(S,H) G2FD042(S,H) G2FD046(S,H) G2FD048(S,H)21, Variable Speed Furnace Coil T.C. S.C. KW G8V***12UHA G1FA036S G8V***12UHA G2FD035(S,H) G8V***16UHB G1FA036S G8V***16UHB G2FD036(S,H) G8V***20UHC G1FA036S G8V***20UHC G2FD036(S,H) G9V***12DHB G2FD036(S,H) G9V***12UPB G1FA036S G9V***12UPB G2FD036(S,H) G9V***16UPC G1FA036S G9V***16UPC G2FD036(S,H) G9V***20UPC G1FA048S G9V***20UPC G2FD042(S,H) G9V***20UPD G2FD048(S,H) Unitary Products Group 17

18 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSING ENTERING AIR TEMPERATURE HABC-(T,W)036S G1FA048S21 IDCFM ID DB ( F) ID WB ( F) T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW N1AHB1246 G2FD036(S,H) N1AHB1246 G2FD046(S,H) G1FA036S G1FA036S17, G2FD035(S,H) G2FD036(S,H) G2FD036(S,H) G2FD042(S,H) G2FD046(S,H) G2FD048(S,H)21, G1HD G1HD G1NA036S17L G1NA048S21D G1UA036S G1UA036S17, G1UA048S Variable Speed Furnace Coil T.C. S.C. KW G8V***12UHA G1FA036S G8V***12UHA G2FD035(S,H) G8V***16UHB G1FA036S G8V***16UHB G2FD036(S,H) G8V***20UHC G1FA036S G8V***20UHC G2FD036(S,H) G9V***12UPB G1FA036S G9V***12UPB G2FD036(S,H) G9V***16UPC G1FA036S G9V***16UPC G2FD036(S,H) G9V***20UPC G1FA048S G9V***20UPC G2FD042(S,H) G9V***20UPD G2FD048(S,H) Unitary Products Group

19 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. INDOOR COIL MODEL NO. CONDENSING ENTERING AIR TEMPERATURE HBBC-F042S G1FA048S21 IDCFM ID DB ( F) ID WB ( F) T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW T.C S.C KW NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree belowthe listed temperature. Air Handler Coil T.C. S.C. KW F2RP/F2FP F2FP N1AHC1606 G2FD042(S,H) N1AHC1606 G2FD048(S,H) N1VSC16 G2FD048(S,H) G1FA048S G1FA060S21, G1HD G1NA048S21D G1UA048S G1UA048S G1UA060S21, G2FD042(S,H) G2FD046(S,H) G2FD048(S,H)21, Variable Speed Furnace Coil T.C. S.C. KW G8V***16UHB G1FA048S G8V***20UHC G1FA048S G9V***20DHD G2FD048(S,H) G9V***16UPC G1FA048S G9V***20UPD G1FA060S G9V***20UPD G2FD048(S,H) Unitary Products Group 19