SUNLINE 2000 SPLIT-SYSTEM AIR-COOLED CONDENSING UNITS DESCRIPTION FEATURES H4CE090 & H2CE120 & H1CE /2, 10, & 12-1/2 NOMINAL TONS

Transcription

1 TG1Y (595) SPLIT-SYSTEM AIR-COOLED CONDENSING UNITS H4CE090 & H2CE120 & H1CE /2, 10, & 12-1/2 NOMINAL TONS EER SUNLINE 2000 HCE /230/460 VOLT ONLY 208/230/575 VOLT ONLY DESCRIPTION These Sunline 2000 units are completely assembled, piped and wired at the factory to provide one-piece shipment and rigging. Each unit is pressurized with a holding charge of refrigerant-22 for storage and/or shipping. The compact design, clean styling, low silhouette, and quiet operation make these condensing units suitable for almost any outdoor location. On rooftops... because they weigh much less than a single package unit of similar capacity and are much easier to rig and support. At ground level... because their ample sub-cooling capacity allows them to be located 60 feet below the evaporator coil. All sheet metal parts are constructed of commercial grade (G90) galvanized steel. After fabrication, each part is thoroughly cleaned to remove any grease or dirt from its surfaces. The external parts are coated with a desert sand powder paint to assure a quality finish for many years. This UL approved coating system has passed the 750 hour, 20% salt spray test per ASTM Standard B117. All models include a 1-year limited warranty on the complete unit. The compressor carries an additional 4-year warranty. A complete line of Evaporator Blower units is also offered to meet your precise capacity and air handling requirements. Refer to Form TG4Y for more information on this air side equipment. FEATURES Condenser coil constructed of copper tubes and aluminum fins for durability and long lasting efficient operation. The coil fins are protected with a decorative grille. Permanently attached base rails with fork lift slots and lifting holes. This design allows for 3-way fork lift access and overhead rigging. Both high and low pressure controls. Since these controls are self-contained, there are no capillary lines to be damaged. Compressor line-break motor protection and crankcase heaters. (No crankcase heater on HCE150 scroll compressors.) Anti-short cycle timer to protect the compressor. A lockout circuit to prevent the unit from cycling on safety control. A 24-volt temperature control circuit. Low ambient operation to 45 F. (Accessories for 0 F low ambient operation are available.) A filter-drier and a moisture indicating sight glass (shipped in the unit s compressor compartment for field installation near the evaporator coil). Service valves with a back-seating access port for pressure testing the system. Copper stub-outs are factory mounted on the suction and liquid service valves to simplify the field piping connections. Separate panel for easy access to the control box without affecting air flow across the condenser coil. Hole in piping panel to accommodate gauge lines to refrigerant fittings in the unit. Packaging suitable for outdoor storage.

2 TG1Y ARI RATINGS 1 CONDENSING UNIT MODEL INDOOR BLOWER UNIT MODEL SYSTEM MBH SYSTEM EER CONDENSING UNIT SOUND LEVEL 2 (bels) H4CE090A25, 46 K4EU090A K3EU120A H2CE120A25, 46 K3EU120A K1EU180A H1CE150A25, 46 K1EU180A Ratings are in accordance with ARI Standard Deduct 0.5 MBH for units operating at 208 volts. 2 Sound ratings are in accordance with ARI Standard Deduct 1.0 MBH for units operating at 208 volts. EER = Energy Efficiency Ratio at full load - the cooling capacity in Btu s per hour (Btuh) divided by the power input in watts, expressed in Btuh per watt (Btuh/watt). APPLICATION DATA Voltage Variation 1 LIMITATION MIN. MAX V 504V V 630V 208/ V 252V 380/ V 456V Ambient Air on Condenser Coil. 45 F F 3 Suction Pressure at Compressor and Corresponding Temp. at Saturation 57.5 psig 32.0 F 90.0 psig 53.5 F 1 Utilization range A in accordance with ARI Standard Low Ambient accessories are available to permit stable system operation at ambient temperatures down to 0 F. 3 These units can operate at a maximum ambient temperature of 120 F providing the wet bulb temperature of the air entering the evaporator coil does not exceed 67 F. NOTE: Refer to Form N1Y for refrigerant piping limitations. PHYSICAL DATA Model HCE Compressor (Tandem 1 ) Rating (Tons) Cap. (Stages) Qty. Dia. (in.) Condenser Fan (Propeller) Fan Motor 2 Coil 4 Nom. CFM Qty. Blades Pitch (Deg.) Qty. HP RPM Rotation 3 Area Face (Ft. 2 ) Finned Length (in.) Rows High Unit Weight (Lbs.) Charge, Lbs.-Oz. (Refrigerant-22) Ship. Oper. Holding Oper / / CW / CCW / / CCW and 120 units only 2 These PSC motors are directly connected to the condenser fans and have inherent protection, ball bearings and a 48 frame. 3 When viewing the shaft end of the motor. 4 These condenser coils have 2 rows of 3/8" OD copper tubes and 16 aluminum fins per inch. 5 Includes matched indoor blower unit but no piping. 6 Add an additional 1 lb. charge when used with KEU120 (10 ton) indoor units. 7 Add an additional 5 lbs. charge when used with KEU180 (15 ton) indoor units. ELECTRICAL DATA MODEL (HCE) VOLTAGE CODE POWER SUPPLY COMPRESSOR RLA LRA CONDENSER FAN MOTOR POWER SUPPLY HP QTY FLA UNIT AMPACITY (AMPS) MAX. FUSE SIZE 1 (AMPS) / / / / / / / / / / / / / / / Dual element. 2 Based on three, 60 C insulated copper conductors in steel conduit. 3 Unit includes a 575 to 460-volt transformer. MIN. WIRE SIZE 2 (AWG) 2 Unitary Products Group

3 UNIT COOLING CAPACITIES AND POWER REQUIREMENTS Model HCE Suction Press. & Corresponding Temperature of Air on Condenser Coil, F Saturation PSIG F MBH KW* MBH KW* MBH KW* MBH KW* MBH KW* MBH KW* *Includes compressor and condenser fan motor(s) TG1Y Unitary Products Group 3

4 TG1Y SYSTEM COOLING CAPACITIES AND POWER REQUIREMENTS Air On Temperature of Air on Condenser Cooling 95 F 105 F 115 F Coil Total Power Sensible Capacity, MBH Total Power Sensible Capacity, MBH Tot al Power Sensible Capacity, MBH CFM WB Cap., Input, Entering Dry Bulb, F Cap., Input, Entering Dry Bulb, F Cap., Input, Entering Dry Bulb, F F MBH KW MBH KW MBH KW H4CE090/K4EU H4CE090/K3EU H2CE120/K3EU H2CE120/K1EU Nominal Rating All Sensible Capacity NOTE: These capacities are gross ratings. For net capacities, determine the KW requirement of the supply air blower motor per the published BLOWER PERFORMANCE data. Convert KW to MBH per the following equation and deduct this equivalent heat from the gross cooling ratings. Blower Motor KW x The KW input ratings listed above include the compressor and condenser fan motor(s) MBH = Blower Motor Heat (MBH) KW 4 Unitary Products Group

5 SYSTEM COOLING CAPACITIES AND POWER REQUIREMENTS TG1Y Air On Temperature of Air on Condenser Cooling 95 F 105 F 115 F Coil Total Power Sensible Capacity, MBH Total Power Sensible Capacity, MBH Tot al Power Sensible Capacity, MBH CFM WB Cap., Input, Entering Dry Bulb, F Cap., Input, Entering Dry Bulb, F Cap., Input, Entering Dry Bulb, F F MBH KW MBH KW MBH KW H1CE150/K1EU All Sensible Capacity NOTE: These capacities are gross ratings. For net capacities, determine the KW requirement of the supply air blower motor per the published BLOWER PERFORMANCE data. Convert KW to MBH per the following equation and deduct this equivalent heat from the gross cooling ratings. The KW input ratings listed above include the compressor and condenser fan motor(s). FIELD WIRING FIELD-INSTALLED ACCESSORIES - 0 F LOW AMBIENT KITS - An auto-transformer and temperature control maintain stable system operation by reducing the speed of the condenser fan motor. Unitary Products Group 5

6 TG1Y UNIT DIMENSIONS & CLEARANCES - HCE090, 120 & 150 CLEARANCES Overhead (Top) 1 120" Front 30" (Piping and Access Panels) Left Side 24" Right Side 24" Rear 24" Bottom 2 0" 1 Units must be installed outdoors. Overhanging structures or shrubs should not obstruct condenser air discharge. 2 Adequate snow clearance must be provided if winter operation is expected. CENTER OF GRAVITY HCE090 (7-1/2 TON) Unit Dim. (in.) A B C D 7-1/2 Ton 42-3/4 31-3/4 19-3/4 11-1/2 10 Ton 70-1/ /8 16-1/2 12-1/2 Ton 70-1/ /8 16-1/2 All dimensions are in inches. They are subject to change without notice. Certified dimensions will be provided upon request. (HCE120) 1-3/8" OD (HCE150) SUCTION LINE HCE120 (10 TON) HCE150 (12-1/2TON) 6 Unitary Products Group

7 TG1Y Unitary Products Group 7

8 Unitary Products Group P.O. Box 1592, York, Pennsylvania USA Subject to change without notice. Printed in U.S.A. Copyright by York International Corporation All Rights Reserved. Code: EBY, EGY TG1Y Supersedes: TG1Y(593) TG1Y(495)