Bohle SlideTec optima 150 without Dampener Glass thickness 8, 10 or 12 mm tempered or laminated glass, up to 150 kg single leaf (with calculations)

Transcription

1 BO BO Bohle SlideTec optima 150 without Dampener Glass thickness 8, 10 or 12 mm tempered or laminated glass, up 150 kg single leaf (with calculations)

2 General information Technical information Suitable for ughened (ESG) and laminated (VSG) safety glass Maximum leaf weight 150 kg Glass thicknesses: 8, 10 and 12 mm All dimensions in millimeter Important information Glass panes with surface protection coating cannot be used with the Optima 150 clamping technology. When installing the p hangers and, if applicable, the door damper, the glass pane must be clean and free of grease in the clamping areas. Therefore, clean the pane in this area with, for example, white spirits or acene. We also recommend that you clean the clamping surfaces in the p hanger and door damper o. For assemblies that, e.g. run in a masonry wall or for two-leaf assemblies, fit the glass sliding doors with additional glass edge protection on the impact sides. Required ols 17 Nm width Size 2,5 A/F 13 3 and 4 2

3 General information () Scope of delivery BO BO Track without fixed glazing 2. Cover 3. Caps (Optional) 4. Top Clamp 5. End sp, left-hand side 6. End sp, right-hand side 7. Botm guide 8. Botm bump sp (Optional) 9. Spacer plate 10. Screw M5 x Drill template for laminated glass 3

4 Wall Mount without fixed glazing Drilling height (BH): BH = LH + X + 45 GH = BH Part-no.: BO Part-no.: BO Ceiling Mount without fixed glazing GH = LH Part-no.: BO Part-no.: BO Wall/Ceiling Mount without fixed glazing continuous wall with flat-covered door handle Panel without fixed glazing Example: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Width Door Panel (GB): GB = LW Example: GB = = Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel Weight door panel (G) = kg: G = GH x GB x GD x Example: G = x x x = kg Track length (L) door handle (covered): L = GB + LW Example: L = = Walk-through distance (DB) covered handle: DB = LW Example: DB = All dimensions in millimeter 4

5 Wall Mount without fixed glazing Drilling height (BH): BH = LH + X + 45 GH = BH Part-no.: BO Part-no.: BO Ceiling Mount without fixed glazing GH = LH Part-no.: BO Part-no.: BO Wall/Ceiling Mount without continuous wall, half covered door handle Panel without fixed glazing Example: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Width Door Panel (GB): GB = LW Example: GB = = Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel Weight door panel (G) = kg: G = GH x GB x GD x Bsp.: G = x x x = kg Track length (L) door handle (half covered): L = GB + LW - GA1 Example: L = = Walk-through distance (DB) half covered handle: DB = LW - GA Example: DB = = All dimensions in millimeter 5

6 Wall Mount without fixed glazing Drilling height (BH): BH = LH + X + 45 GH = BH Part-no.: BO Part-no.: BO Ceiling Mount without fixed glazing GH = LH Part-no.: BO Part-no.: BO Wall/Ceiling mount without fixed glazing w/continuous wall with ladder handle Panel without fixed glazing Example: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Width Door Panel (GB): GB = LW Example: GB = = Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel Weight door panel (G) = kg: G = GH x GB x GD x Example: G = x x x = kg Track length (L) : L = GB + LW - GA1 - GA2 Example: L = = Walk-through distance (DB): DB = LW - GA1 - GA Example: DB = = All dimensions in millimeter 6

7 Wall Mount without fixed glazing Drilling height (BH): BH = LH + X + 45 GH = BH Part-no.: BO Part-no.: BO Ceiling Mount without fixed glazing GH = LH Part-no.: BO Part-no.: BO Wall/Ceiling mount without fixed panel with end wall, covered flat handle Panel without fixed glazing Example: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Width Door Panel (GB): GB = LW Example: GB = ,00 = Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel Weight door panel (G) = kg: G = GH x GB x GD x Example: G = x x x = kg Track length (L) door handle (covered): L = GB + LW Example: L = = Walk-through distance (DB) covered handle: DB = LW Example: DB = All dimensions in millimeter 7

8 Wall Mount without fixed glazing Drilling height (BH): BH = LH + X + 45 GH = BH Part-no.: BO Part-no.: BO Ceiling Mount without fixed glazing GH = LH Part-no.: BO Part-no.: BO Wall/ceiling mount without fixed glazing with end wall, half covered flat handle. Panel without fixed glazing Example: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Width Door Panel (GB): GB = LW Example: GB = = Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel Weight door panel (G) = lbs: G = GH x GB x GD x Example: x x x = kg Track length (L) door handle (covered): L = GB + LW - GA Example: L = = Walk-through distance (DB) door handle (covered): DB = LW - GA Example: DB = = All dimensions in millimeter 8

9 Wall Mount without fixed glazing Drilling height (BH): BH = LH + X + 45 GH = BH Part-no.: BO Part-no.: BO Ceiling Mount without fixed glazing GH = LH Part-no.: BO Part-no.: BO Wall/ceiling mount without fixed glazing with end wall, ladder handle Panel without fixed glazing Example: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Width Door Panel (GB): GB = LW Example: GB = = Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel Weight door panel (G) = lbs: G = GH x GB x GD x Example: G = x x x = kg Track length (L): L = GB + LW - GA1 - GA Example: L = = Walk-through distance (DB) DB = LW - GA1 - GA Example: DB = = All dimensions in millimeter 9

10 Size 2,5 1 Slide sppers in track and position in desired location without covering any fixing bore holes. 2 Install track level either on wall or ceiling. NOTE: Fix track only with suitable load bearing materials. (stud or solid wood blocking) 10

11 t=3,2mm t=3,2mm t=1,2mm t=3,2mm t=1,2mm t=1,2mm 4a 3 The p hangers are preassembled in the facry for a laminated safety glass pane. If using a tempered glass, the bolts including the sleeves (4a) must be removed. The clamping inserts must be attached on the clamping jaws of the p clamp according the glass thickness. Please peel off the sticker use self adhesive surface. 1 1 Size 3 4 Clean the glass pane with, e.g. white spirits or acene in the area be clamped. We also recommend that you clean the clamping surfaces of the clamp. Lower safety screws (1) until they are flush with clamping plate. 11

12 17 Nm 45 5 Push the p clamp on the glass pane until the protective rubber pushes against the p of the pane. Position each of the clamps 45 mm from the edge of the glass. Tighten clamp with a rque of 17 Nm and use a rque wrench with Torx bit (TX30). IMPORTANT: When installing door damper /soft close system, please refer separate instructions. Different positioning of clamps required. 12

13 6 Use a plumb bob determine the position of the botm guide. Transfer drilling pattern, drill and fix the botm guide [12] 10 (8) [27] 25 (26) 5b 5a IMPORTANT: Clean running surface before inserting door. All rollers are equipped with maintenance free bearings and should not be greased. Position the door pane in the track and align using the eccentric screws (2) and a level. Then tighten the eccentric screws (2) using the counter nuts. Turn the locking screws until they are in light contact with the track, then turn them back again by a ½ turn. Important: The locking screws serve as the anti-jump system and prevent the door from jumping if improperly used. 2 Position the trolley sps in the track at the respective end of the track so that the required door opening is achieved and clamp as follows: screw the p screw (5a) on the spper until the component has set in the track. Now tighten the botm screw (5b) slightly. Then re-tighten both screws by turning them a additional ¼ turn. SW 13 Size 3 and 4 13

14 7 Screw the clamping screws (M5x5) for the pelmet in the track. Use the spacer plate determine the depth. Tighten the screws until they lightly uch the spacer plate. Only use the threaded holes, which are accessible from the botm when the door is moved. M5x5 Size 2,5 Size 2,5 8 Clip the cover in the track, position,apply pressure cover snap in place and use the Allen key tighten the clamping screws. Start in the walk-through area. The Allen key can be guided from screw screw in the guide groove. Important: When dismantling the cover, completely remove the clamping screws. When using the optional end caps: Clean both end surfaces of the profile with Bohle Special cleaner or acene before attaching end caps. 14

15 15

16 General information () Scope of delivery BO BO Track without fixed glazing 2. Cover 3. Caps (Optional) 4. Top Clamp 5. End sp, left-hand side 6. End sp, right-hand side 7. Botm guide 8. Botm bump sp (Optional) 9. Spacer plate 10. Screw M5 x U-channel for side panel 12. Cover profile Drill template for laminated glass 16

17 Ceiling mount with fixed glazing - continuous wall with covered flat handle GH = LH GHS = LH 43 Part-no.: BO Part-no.: BO Panel with fixed glazing E.g.: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Track length (L): L = LW E.g..: L = = Cover profile length (T): T = L - S E.g.: T = = With flat handle Width Door Panel (GB) max. DB. door handle (covered): GB = LW E.g.: GB = = Weight door panel (G) in kg door handle (covered): G = GH x GB x GD x E.g.: G = x x x = 51.5 kg Glass weight with fixed glazing (S) max. DB. door handle (covered): S = LW E.g.: S = = Length u-channel (BP) door handle (covered): BP = S E.g.: BP = Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel Walk-through distance (DB) door handle (covered): DB = L - S E.g.: DB = = All dimensions in millimeter 17

18 Ceiling mount with fixed glazing continuous wall, ladder handle GH = LH GHS = LH 43 Part-no.: BO Part-no.: BO Panel with fixed glazing Example: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Track length (L): L = LW E.g.: L = = Cover profile length (T): T = L - S E.g.: T = = Width Door Panel (GB) max. DB GB = LW GA1 + GA E.g.: GB = = 1040 Weight door panel (G) in kg: G = GH x GB x GD x E.g.: G = x x x = kg Glass weight with fixed glazing (S) max. DB S = LW GA1 - GA E.g.: S = = Length u-channel (BP): BP = S E.g.: BP = Walk-through distance (DB) : DB = LW - GA1 - GA Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel E.g.: DB = = All dimensions in millimeter 18

19 Ceiling wall with fixed panel, fixed wall, covered flat handle GH = LH GHS = LH 43 Part-no.: BO Part-no.: BO Panel with fixed glazing Example: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Track length (L): L = LW E.g.: L = Cover profile length (T): T = L - S E.g.: T = = Width Door Panel (GB) max. DB. door handle (covered): GB = LW E.g.: GB = = Weight door panel (G) in kg door handle (covered): G = GH x GB x GD x E.g.: G = x x x = kg Glass weight with fixed glazing (S) max. DB. door handle (covered): S = LW E.g.: S = = Length u-channel (BP) door handle (covered): BP = S E.g.: BP = = Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel Walk-through distance (DB) door handle (covered): DB = L - S E.g.: DB = = All dimensions in millimeter 19

20 Ceiling mount with fixed panel with fixed wall, half covered flat handle GH = LH GHS = LH 43 Part-no.: BO Part-no.: BO Panel with fixed glazing Example: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Track length (L): L = LW E.g.: L = Cover profile length (T): T = L - S E.g.: T = = Width Door Panel (GB) max. DB. door handle (half covered): GB = LW (GA1-4) E.g.: GB = ( ) = Weight door panel (G) in kg door handle (half covered): G = GH x GB x GD x E.g.: G = x x x = kg Glass weight with fixed glazing (S) max. DB. door handle (half covered): S = LW GA E.g.: S = = Length u-channel (BP) door handle (half covered): BP = S E.g.: BP = = Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel Walk-through distance (DB) door handle (half covered): DB = L - S - GA1 E.g.: DB = = All dimensions in millimeter 20

21 Ceiling mount with fixed glazing and fixed wall, ladder handle GH = LH GHS = LH 43 Part-no.: BO Part-no.: BO Panel with fixed glazing Example: GH = ; GA1 = 80.00; GD = 10.00; LW = ; GA2 = Track length (L): L = LW E.g.: L = Cover profile length (T): T = L - S E.g.: T = = Width Door Panel (GB) max. DB GB = LW + GA1 + GA E.g.: GB = = Weight door panel (G) in kg: G = GH x GB x GD x E.g.: G = x x x = kg Glass weight with fixed glazing (S) max. DB: S = LW - GA1 - GA E.g.: S = = Length u-channel (BP): BP = S E.g.: BP = = Walk-through distance (DB) : DB = L - S - GA1 - GA2 E.g.: DB = = Legend: LH = Clear height LW = Clear width BH = Drill height GH = Glass height GB = Width Door panel MG = Door handle L = Track length GA1 = Handle distance 1 GA2 = Handle distance 2 GD = Glass thickness DB = Walk through distance G = Weight T = Cover profile length S = Side panel BP = Floor profile GHS = Height side panel All dimensions in millimeter 21

22 Size 2,5 1 Slide sppers in track and position in desired location without covering any fixing bore holes. 2 Install track level on ceiling. NOTE: Fix track only with suitable load bearing materials. (stud or solid wood blocking) 22

23 3 Use a plumb bob determine the position of the botm guide. Transfer drilling pattern, drill and fix the botm guide. Clean U-channel (20 x 20 x 2 mm) and insert setting blocks (5 x 15 mm) in u-channel To insert the side panel, slightly tilt it and lift it in the u-shaped channel of the track until it fits above the channel at the botm. Then position and align the pane and use plastic setting blocks clamp it at the p and botm at the sides. Or when using 10 mm glass, use rubber profile BO

24 t=3,2mm t=3,2mm t=1,2mm t=3,2mm t=1,2mm t=1,2mm 4a 5 The p hangers are preassembled in the facry for a laminated safety glass pane. If using tempered glass, the bolts including the sleeves (4a) must be removed. The clamping inserts must be attached on the clamping jaws of the p hangers according the glass thickness. Please peel of sticker use self adhesive surface. 17 Nm 45 6 Push the p clamp on the glass pane until the protective rubber pushes against the p of the pane. Position each of the clamps 45 mm from the edge of the glass. Tighten clamp with a rque of 17 Nm and use a rque wrench with Torx bit (TX30). IMPORTANT: When installing door damper/soft close system, please refer separate instructions. Different positioning of clamps required. 24

25 1 7 Clean the glass pane with, e.g. white spirits or acene in the area be clamped. We also recommend that you clean the clamping surfaces of the clamp. Lower safety screws (1) until they are flush with clamping plate. 1 Size 3 8 IMPORTANT: Clean running surface before inserting door. All rollers are equipped with maintenance free bearings and should not be greased. Position the door pane in the track and align using the eccentric screws (2) and a level. Then tighten the eccentric screws (2) using the counter nuts. Turn the locking screws until they are in light contact with the track, then turn them back again by a ½ turn. Important: The locking screws serve as the anti-jump system and prevent the door from jumping if improperly used. 2 Position the trolley sps in the track at the respective end of the track so that the required door opening is achieved and clamp as follows: screw the p screw (5a) on the spper until the component has set in the track. Now tighten the botm screw (5b) slightly. Then re-tighten both screws by turning them a additional ¼ turn. 5b 5a SW 13 Size 2,5 3 and 4 25

26 9 M5x5 Screw the clamping screws (M5x5) for the cover in the track. Use the spacer plate determine the depth. i.e. turn screws until they lightly uch the spacer plate. Only use the threaded holes, which are accessible from below when the door is moved Size 2,5 10 If necessary, cut cover size and insert in the channel of the side panel in the walk through area 11 Clip the cover in the track, position, apply pressure cover snap in place and use the Allen key tighten the clamping screws. Start in the walkthrough area. The Allen key can be guided from screw screw in the guide groove. Important: When dismantling the cover, completely remove the clamping screws. Größe 2,5 When using the optional end caps: Clean both end surfaces of the profile with Bohle Special cleaner or acene before attaching end caps. 26

27 27

28 Germany Austria United Kingdom Bohle AG - Head Office Dieselstraße 10 D Haan Bohle GmbH Lemböckgasse 63/1/1 A-1230 Wien Bohle Ltd Fifth Avenue, Tameside Park Dukinfield, Cheshire, SK16 4PP T F info@bohle.de T F info@bohle.at T: F: info@bohle.ltd.uk