LSM SFM. METRIC SPECIFICATIONS and TECHNICAL INFORMATION

Transcription

1 Metric Bushings Specifications M is for Metric RCM LSM SFM SFXM LM PM HM HLM SPM NM SCM FGM HGM SPECIFICATIONS and TECHNICAL INFORMATION BUSHING INFORMATION Application Information is listed on the specific page for each type of metric bushings. UNITED Metric Bushings are manufactured to ANSI, Metric and UNITED standards. Most UNITED bushings are noncounterbored, adding critical guidance to insure precise location and eliminating "drill walk." Bushings generally assume the shape of the jig plate hole. Care must be taken to jig bore or ream size the hole to achieve hole roundness. Please use our Jig Bore Chart, shown on right, for all Metric Press Fit Bushings. Lubricated bushing O.D.s and lubricated mounting holes assure easier installation and removal. They prevent the bushing from picking up metal chips that may score the hole. Install PM, LM, HM, HLM and SPM Bushings with a hand arbor press or bushing installation assembly tools into your jig plates. Maintain perpendicularity to centerline. Locate the lead chamfer of the bushing in the hole carefully to direct the installation. Prepare your installation hole size consistently with our Jig Bore Chart for all Metric Press Fit type bushings. All Metric Press Fit bushings have a.02mm ground lead to automatically center your bushings. JIG BORE and JIG GRIND CHART for PRESS FIT BUSHINGS NOM ACTUAL ACTUAL JIG BORE INSTALLATION O.D. O.D. O.D. INSTALLATION MM MM in INCHES HOLE SIZE HOLE SIZE in INCHES MINIMUM and MAXIMUM INSIDE DIAMETERS of Bushings in accordance with TOLERANCE CLASS G6. Inside Diameter (I.D.) is concentric to outside (O.D.) within.012 T.I.R. Metric or.0005 Inches. Surface Finish on I.D. is 0.4 micrometers or better. Hardness is RC in the hole. Small I.D. Sizes thru 0.80 mm (.032 inch) may be counterbored to provide for lubrication and chip clearance. BUSHING AND DRILL EQUIVALENCY I. D. TOLERANCE FOR I. D. REAMER SIZES DRILL SIZES I. D. TOLERANCES U.S.A. INCH in INCHES U.S.A. INCH Up to 3mm Nominal mm / mm Up to.1181 Nominal / mm / mm / mm to 6mm Nominal mm / mm.1181 to.2362 Nominal / mm / mm / mm to 10mm Nominal mm / mm.2362 to.3937 Nominal / mm / mm / mm to 18mm Nominal mm / mm.3937 to.7087 Nominal / mm / mm / mm to 30mm Nominal mm / mm.7087 to Nominal / mm / mm / mm to 50mm Nominal mm / mm to Nominal / mm to 80mm Nominal mm / mm to Nominal / mm to 120mm Nominal mm / mm to Nominal / A24 UNITED HAS ALL THE YOU REQUIRE IN BUSHINGS!

2 Standard Metric & Standard Inch Drill Sizes & Drill Bushing Sizes THOSE NOT LISTED ARE SPECIALS IN & INCHES. Metric-Inch I.D. Std. Drills & Bushings Drill Sizes INCH DECIMAL INCH DECIMAL INCH DECIMAL INCH DECIMAL INCH DECIMAL J / K / / / / / / L / M / / / N / / / / / / / O / / P / / / / / Q / / R / / / / / / S / / T / / / / A / / U / / B / / C.2420 V / D, / / / E.2500 W / / / / F.2570 X / / G.2610 Y / / / Z / / H / / " / I / / LARGER STANDARDS : Plus 1.00MM increments up to 50.00MM Plus 5.00MM increments up to MM INCHES: Plus 1/64" increments up to 2" Plus 1/32" increments up to 3" Plus 1/16" increments up to 4" Plus 1/8" increments up to 5" Refer to page V59 for sizes over 26.00MM and Tap Bushings sizes. NON-STANDARD I.D.s are PRICED as SPECIALS WOODRUFF AVE. DOWNEY, CA TELEPHONE (562) / (800) IN CA / FAX (562) /(800) A25

3 C PM LENGTH OVERALL / ANSI LENGTH FOR (±0.4 MM / ±.015") U.S.A. INCH NOM. USA INCH INCH: I. D. O.D. (s6) DECIMAL MM. MAX MIN MAX MIN : MIN A I.D. DRILL RANGE MM SIZES INCH SIZES #80 - # #60 - # #49 - # #37 - # # # # B # # / / O - 25/ X - 15/ /64-37/ /32-45/ /32-55/64 PM - Headless Press Fit Metric Headless Press Fit PM Headless Press Fit Type PM For the World Specify PM Ground or PUM Unground Order as: PM (TYPE O.D. LEN I.D.) RC T.I.R..012 (.0005 inch) MAX. PM Bushings are the most popular and least expensive. PM Bushings are pressed into fixtures or jig plates where replacement due to wear is not anticipated. Ideal for close hole spacing. Usually mounted flush to jig plate. PM Bushings have blended entrance radii, concentric ground leads, and are manufactured from long wear premium steel. ALL UNITED STANDARD BUSHINGS ARE MANUFACTURED TO UNITED, U.S.A. ANSI AND STANDARDS PM-4 PM PM SIZES ONLY. REFER to /STD CHART PM PM PM PM PM PM PM PM PM PM PM A I.D. DRILL RANGE C PM LENGTH OVERALL / ANSI LENGTH FOR (±0.4 MM / ±.015") U.S.A. INCH NOM. USA INCH INCH: I. D. O.D. (s6) MM SIZES DECIMAL MM. MAX MIN MAX MIN : MIN INCH SIZES PM-35 PM 2.4 7/8-1-1/ PM-42 SIZES ONLY / / REFER to /STD CHART PM /16-1-3/ PM / / PM /32-1-7/ PM /64-2-5/ PM / / PM /64-2-3/ PM /4-3-1/ PM / / PM / / PM /64-4-1/ A26 UNITED HAS ALL THE YOU REQUIRE IN BUSHINGS! A B C BLENDED I. D. RADIUS

4 Head Press Fit Type HM For the World Specify HM Ground and HUM Unground HM LENGTH MEASURED OVERALL The USA inch standard specifies lengths for H Bushings under the head. HEADLINERS HLM and HM have IDENTICAL HEAD DIMENSIONS EXAMPLE Order as: HM (TYPE O.D. LEN I.D.) RC T.I.R..012 (.0005 inch) MAX. HM Bushings are preferred, if space permits, as heavy drilling will not force HM bushings out of the fixture. ALL UNITED STANDARD BUSHINGS ARE MANUFACTURED TO UNITED, U.S.A. ANSI AND STANDARDS. BLENDED I.D. RADIUS C HM - Head Press Fit Metric Head Press Fit HM C HM LENGTH OVERALL / ANSI LENGTH FOR (±0.4 MM = ±.015") U.S.A. INCH NOM. USA INCH INCH: F G O.D. (s6) MM SIZES DECIMAL MM. MAX MIN MAX MIN : MM MM HM HM 7 2 #80 - # HM SIZES ONLY. 7 2 #60 - # REFER to /STD CHART HM #49 - # HM #37 - # HM #29 - # HM #22 - # A I.D. DRILL RANGE # / B - 5/ O - 25/ X - 15/ /64-37/ /32-45/ /32-55/ HM HM HM HM HM HM HM A I.D. DRILL RANGE C HM LENGTH OVERALL / ANSI LENGTH FOR (±0.4 MM = ±.015") U.S.A. INCH NOM. USA INCH INCH: F G O.D. (s6) MM SIZES DECIMAL MM. MAX MIN MAX MIN : MM MM HM HM /8-1-1/ HM SIZES ONLY / / REFER to /STD CHART HM /16-1-3/ HM / / HM /32-1-7/ HM /64-2-5/ HM / / HM /64-2-3/ HM /4-3-1/ HM / / HM / / HM /64-4-1/ WOODRUFF AVE. DOWNEY, CA TELEPHONE (562) / (800) IN CA / FAX (562) /(800) A27

5 A28 SFM Metric Slip Fit Renewable Slip Fit Renewable SFM Originated by UNITED Patent No. 3,606,566 ALL UNITED STANDARD BUSHINGS ARE MANUFACTURED TO UNITED, U.S.A. ANSI AND STANDARDS. SFM LENGTHS measured UNDER the head. A I.D. DRILL RANGE Slip Fit Renewable Type SFM Metric Bushings R RC T.I.R..012 (.0005 inch) MAX. Used with LM or HLM LINERS. EXAMPLE Order as: SFM (TYPE-O.D.-LEN-I.D.) Easy and Quick to change sizes of drill, reamer, tap or countersink. SFM Bushings are ideal for long run tool changes. Used in production lines where multiple operations are performed such as drilling, reaming, countersink and tapping. Knurled for non-slip easy installation. Three metric lengths are provided in most cases: SFM accommodates Lock Screws and Round Clamps. Short, Medium and Long. C SFM LENGTH UNDER HEAD / ANSI LENGTH FOR (±0.4 MM / ±.015") U.S.A. INCH NOM. USA INCH INCH: F G O.D. (h5) MM SIZES DECIMAL MM. MAX MIN MAX MIN : MM MM # # # # #49 - # #21-15/ B - 5/ O - 25/ X - 15/ /64-37/ /32-45/ SFM SFM SFM SIZES ONLY REFER to /STD CHART SFM SFM SFM SFM SFM SFM SFM /32-55/ SFM /8-1-1/ SFM A I.D. DRILL RANGE C SFM LENGTH UNDER HEAD / ANSI LENGTH FOR (±0.4 MM / ±.015") U.S.A. INCH NOM. O.D. (h5) USA INCH INCH: F G MM SIZES DECIMAL MM. MAX MIN MAX MIN : MM MM SFM SFM 1-1/ / SFM SIZES ONLY. 1-3/16-1-3/ REFER to /STD CHART / / SFM /32-1-7/ SFM /64-2-5/ SFM /32-2-7/ SFM /16-2-3/ SFM /4-3-1/ SFM / / SFM UNITED HAS ALL THE YOU REQUIRE IN BUSHINGS!

6 Lock Screws and Round Clamps for SFM Slip Fixed Locking Dimensions The Metric Bushing designed to please everyone! Originated by UNITED Patent No. 3,606,566 For SFM Bushings Lock Screws & Clamps I.D. RADIUS BLENDED UNITED has the world's largest inventory of SF inch standards! DIA. ENTRANCE HEAD HEAD SLOT SLOT MOUNTING O.D. RADII DIA. THICK HT. DISTANCE LOCATION (h5) MIN (±0.4) (±0.4) (±0.13) (±0.4) (±0.4) LOCK ROUND B MM D MM F MM G MM H MM J MM L R MM SCREWS CLAMPS LSM-1 &-2 RCM-1 & LSM-1 &-2 RCM-1 & LSM-3 &-4 RCM-3 & LSM-3 &-4 RCM-3 & LSM-3 &-4 RCM-3 & LSM-5 &-6 RCM-5 & LSM-5 &-6 RCM-5 & LSM-5 &-6 RCM-5 & LSM-5 &-6 RCM-5 & LSM-5 &-6 RCM-5 & LSM-7 &-8 RCM-7 & LSM-7 &-8 RCM-7 & LSM-7 &-8 RCM-7 & LSM-7 &-8 RCM-7 & LSM-7 &-8 RCM-7 & LSM-7 &-8 RCM-7 & LSM-7 &-8 RCM-7 & LSM-7 &-8 RCM-7 &-8 SFM Locate Lock Screws and Round Clamps RCM ROUND CLAMPS RCM-1 thru RCM-8 Dependable Designed to Hold Perfect for SFMs! Please refer to Page A35 for complete specifications for Round Clamps and Lock Screws. LSM LOCK SCREWS LSM-1 thru LSM-8 For Close Hole Spacing Black Oxide Finish $3.13 RCM LSM $1.01 MINIMUM and MAXIMUM INSIDE DIAMETERS of Bushings in accordance with TOLERANCE CLASS G6. Inside Diameter (I.D.) is concentric to outside (O.D.) within.012 T.I.R. Metric or.0005 Inches. Surface Finish on I.D. is 0.4 micrometers or better. Hardness is RC in the hole. Small I.D. Sizes thru 0.80 mm (.032 inch) may be counterbored to provide for lubrication and chip clearance. BUSHING AND DRILL EQUIVALENCY I. D. TOLERANCE FOR I. D. REAMER SIZES DRILL SIZES I. D. TOLERANCES U.S.A. INCH in INCHES U.S.A. INCH Up to 3mm Nominal mm / mm Up to.1181 Nominal / mm / mm / mm to 6mm Nominal mm / mm.1181 to.2362 Nominal / mm / mm / mm to 10mm Nominal mm / mm.2362 to.3937 Nominal / mm / mm / mm to 18mm Nominal mm / mm.3937 to.7087 Nominal / mm / mm / mm to 30mm Nominal mm / mm.7087 to Nominal / mm / mm / mm to 50mm Nominal mm / mm to Nominal / mm to 80mm Nominal mm / mm to Nominal / mm to 120mm Nominal mm / mm to Nominal / WOODRUFF AVE. DOWNEY, CA TELEPHONE (562) / (800) IN CA / FAX (562) /(800) A29

7 STANDARD LINER I.D.TOLERANCES U.S.A. INCHES 6 to 10 MM / MM to 18 MM / MM to 30 MM / MM to 50 MM / MM to 80 MM / MM to 120 MM / MM A I.D. LINER MET. C LM LENGTH OVERALL / ANSI LENGTH FOR ±0.4 MM = ±.015" NOM. U.S.A. INCH NOM. USA INCH INCH: FITS G6 O.D. s6 SFM MM ACTUAL DECIMAL MM MAX MIN MAX MIN : BUSH LM LM 8 SIZES ONLY LM REFER to /STD CHART LM LM LM LM LM LM LM LM LM A I.D. LINER C LM LENGTH OVERALL / ANSI LENGTH FOR MET. ±0.4 MM = ±.015" NOM. G6 U.S.A. INCH NOM. O.D. s6 USA INCH INCH: FITS SFM MM ACTUAL DECIMAL MM MAX MIN MAX MIN : BUSH LM LM LM LM LM-105 LM LM-115 SIZES ONLY REFER to /STD CHART LM A30 LM - Press Fit Metric Liners A Headless Liners LM B Metric Liners Type LM Headless Press Fit C BLENDED I.D. RADIUS RC Use With Slip Fixed Renewable Bushings - SFMs Specify LM Ground or LUM T.I.R..012 (.0005 inch) MAX. LM Bushings are permanently pressed into fixtures or jig plates. Liners maintain precision permanent locations for SFM Slip Fixed Renewable Bushings, Slip Fit Locating Pins and Alignment Pins. Liners reduce wear on jig or fixture and are precision ground. LM Bushings have blended entrance radii, concentric ground leads, and are manufactured from long wear premium steel for ease of press fit installation. ALL UNITED STANDARD BUSHINGS ARE MANUFACTURED TO UNITED, U.S.A. ANSI AND STANDARDS. EXAMPLE Order as: LM (TYPE O.D. LEN I.D.) UNITED HAS ALL THE YOU REQUIRE IN BUSHINGS!

8 Metric Liners Type HLM Head Press Fit For Use With SFM Slip Fixed Renewable Bushings Specify HLM Ground or HLUM RC T.I.R..012 (.0005 inch) MAX. HLM Bushings provide permanent precision location for SFM Slip Fixed Renewable Bushings, Slip Fit Locating Pins and Alignment Pins. BLENDED I.D. RADIUS HLM - Press Fit Metric Liners Ideal for production fixtures. The head prevents liner from pressing thru the fixture with heavy loads. Liners reduce wear on jig or fixture and are precision ground. HLM Lengths, I.D. and O.D. are identical to LM Liners. Lengths are measured overall. HLM Bushings have blended entrance radii, concentric ground leads, and are manufactured from long wear premium steel for ease of press fit installation. Head Liners HLM STANDARD LINER I. D. TOLERANCES U.S.A. INCHES 6 to 10 MM / MM to 18 MM / MM to 30 MM / MM ALL UNITED STANDARD BUSHINGS ARE MANUFACTURED TO UNITED, U.S.A. ANSI AND 30 to 50 MM / MM STANDARDS. Order as: HLM (TYPE-O.D.-LEN-I.D.) 50 to 80 MM / MM to 120 MM / MM A I.D. LINER C HLM LENGTH OVERALL / ANSI LENGTH FOR (±0.4 MM = ±.015") NOM U.S.A. INCH NOM O.D. (s6) USA INCH INCH: F G FITS MM ACTUAL DECIMAL MM MAX MIN MAX MIN : MM MM SFM HLM HLM HLM SIZES ONLY. REFER to /STD CHART HLM HLM HLM HLM HLM HLM HLM HLM HLM A I.D. LINER C HLM LENGTH OVERALL / ANSI LENGTH FOR (±0.4 MM = ±.015") NOM U.S.A. INCH NOM USA INCH INCH: F G FITS O.D. (s6) MM ACTUAL DECIMAL MM MAX MIN MAX MIN : MM MM SFM HLM HLM HLM HLM HLM-105 HLM HLM-115 SIZES ONLY REFER to /STD CHART HLM WOODRUFF AVE. DOWNEY, CA TELEPHONE (562) / (800) IN CA / FAX (562) /(800) A31

9 Metric NM and SCM Bushings for Plastic Nurlock and Ser-Cast Metric NM and SCM Bushings for Potting, Cast Tooling, Plastic and Soft Materials Installation NM or SCM A NM or SCM BLENDED RADIUS COUNTERSINK NM NURLOCK 1 Groove: 6 MM thru 16 MM long 2 Grooves: 20 MM thru 36 MM long SPECIFY NM FOR NURLOCK. UNITED s special Nurlock Diamond Knurls provide superior holding strength for Potted or Cast installation. They resist rotational and axial forces. For greatest accuracy, align and locate by I.D. for RC IN THE HOLE ALL UNITED STANDARD BUSHINGS ARE MANUFACTURED TO UNITED, A I.D. BUSHING ACTUAL SIZE INCH SIZE #61 - # #49 - # #37 - # # # #21 - # #8-15/ B - 5/ O - 25/ X - 15/ /64-37/64 U.S.A. INCH NOM. O.D. (s6) SCM SER-CAST SPECIFY SCM FOR SER-CAST NM and SCM Bushings For Plastic Tooling / /64 SELECT UNITED s special Ser-Cast Serrations allow pressing into aluminum, magnesium, masonite, soft materials or plastic fixtures while providing excellent holding strength A32 UNITED HAS ALL THE YOU REQUIRE IN BUSHINGS! NM C NM & SCM LENGTH OVERALL / ANSI LENGTH FOR (±0.4 MM / ±.015") USA INCH INCH: DECIMAL MM MAX MIN MAX MIN : NM-5 SCM NM-5 SCM NM-6 SCM NM-7 SCM NM-8 SCM NM-10 SCM NM-12 SCM NM-15 SCM NM-18 SCM NM-22 SCM NM-26 SCM Order as: NM (TYPE-O.D.-LEN-I.D.) A NM & SCM SPECIFY TYPE. For PLASTIC Applications : NUMBER of GROOVES:

10 Ser-Press Metric SPM Bushings for Potting, Cast Tooling, Plastic and Soft Materials Installation SER-PRESS prevents spin out EASY PRESS IN On Soft Materials UNITED s SPM Ser-Press Bushing was designed to be pressed into plastic jigs and fixtures. Simultaneously the outside diameter has a ground finish, creating ideal pressing into aluminum, magnesium, masonite and wood. UNITED s special Ser-Press Serrations hold firmly and prevent rotation while resisting axial forces. Serrations are.25mm to.65mm larger than ground O.D. diameter. One-half of the SPM Bushing consists of serrations, and one-half is Press Fit. Ser-Press Bushings are often used in holes drilled in imbedments. Allow adequate interference in your hole preparation to hold the SPM firmly. Allow for chip clearance in your standoff. Refer to our Jig Bore Chart on page A24. Metric Ser-Press Bushings for Plastic SPM SER-PRESS SPECIFY SPM FOR SER-PRESS EXAMPLE Order as: SPM (TYPE-O.D.-LEN-I.D.) ALL UNITED STANDARD BUSHINGS ARE MANUFACTURED TO UNITED, U.S.A. ANSI AND STANDARDS SPM Bushings For Plastic Tooling RC IN THE HOLE A I.D. BUSHING ACTUAL SIZE INCH SIZE #61 - # # #38 U.S.A. INCH NOM. O.D. (s6) T.I.R..012 Max (.0005 inch) C SPM LENGTH OVERALL / ANSI LENGTH FOR (±0.4 MM / ±.015") USA INCH INCH: DECIMAL MM MAX MIN MAX MIN : SPM SPM SPM SPM SPM SPM For PRICES For ARE FOR For STANDARD For SPM SPM SPM SIZES SPM ONLY. FOR SPM For PLASTIC For & SOFT For MATERIALS For # # SPM SPM #29 - # # # SPM SPM #8-15/ B / SPM SPM O - 25/ SPM X - 15/ SPM /64-37/ SPM /32-45/ WOODRUFF AVE. DOWNEY, CA TELEPHONE (562) / (800) IN CA / FAX (562) /(800) A33

11 HGM and FGM Bushings for Plastic Plastic Tooling Specialty Metric Bushings HGM HEXGRIP HAS ONLY ONE FLANGE SPECIFY 'HGM' FOR HEX GRIP SPECIFY 'FGM' FOR FLANGE GROOVE HEXGRIP ELIMINATES MOST SPIN OUT BLENDED RADIUS ALL UNITED STANDARD BUSHINGS ARE MANUFACTURED TO UNITED, U. S.A. ANSI AND STANDARDS. RC in the hole EXAMPLE Order As: HGM (TYPE-O.D.-LEN-I.D.) The Best Hold Out in Potted Bushings! A I.D. DRILL RANGE B Body O.D. SIZE FLANGE O.D. HEX * FLANGE GROOVE HAS SUPERIOR HOLD FGM FLANGE GROOVE HAS ONE TO FOUR GROOVES 10MM LENGTH HAS 1.093" GROOVE 12MM LENGTH HAS 1.125" GROOVE 19MM LENGTH HAS 2.125" GROOVES 25MM LENGTH HAS 3.125" GROOVES 35MM LENGTH HAS 4.125" GROOVES C OVERALL LENGTH ANSI LENGTH ±.50MM (±.020") U.S.A INCH U.S.A INCH (s6) ±0.50 MM INCH: 3/8 1/2 3/4 1" 1-3/8 NOMINAL DECIMAL NOMINAL DECIMAL NOM. DECIMAL (SEE BELOW) : MM MM #55-1/ MM MM HGM-8 OR FGM MM MM #52 - # MM MM HGM-8 OR FGM MM MM #38-9/ MM MM HGM-8 OR FGM MM MM #29 - # MM MM HGM-12 OR FGM MM MM #9 - F MM MM HGM-12. OR FGM MM MM F - 5/ MM MM HGM-16. OR FGM MM MM G - 11/ MM MM HGM-20. OR FGM MM MM Q - 21/ MM MM HGM-25 OR FGM MM MM /64-49/ MM MM HGM-35 OR FGM MM MM /4-1-1/ MM MM HGM OR FGM-45 I. D. O. D *HEX INCH STOCK IS READILY AVAILABLE IN THE U.S.A. HEX BAR STOCK IS NOT READILY AVAILABLE! A34 UNITED HAS ALL THE YOU REQUIRE IN BUSHINGS!

12 Metric Lock Screws and Round Clamps Metric Lock Screws Metric Round Clamps LOCK SCREWS for Slip-Fixed Renewable FLUSH PROTRUDING LSM LOCK SCREWS for STANDARD MOUNTING of Slip-Fixed Renewable Bushings $ 0.80 LOCK SCREW SFM BUSHING BODY DIAMETER A OVERALL LENGTH B SHOULDER DIAMETER C HEAD DIAMETER D SLOT DEPTH E HEIGHT INCL HEAD F HEIGHT UNDER HD (+0.4/+0.2) MM (+.015/+.008) IN. G SLOT WIDTH THREAD NUMBER MM INCH MM INCH MM INCH MM INCH MM INCH MM INCH MM INCH MM INCH SIZE LSM-1 8 to to M5 x 0.8 LSM-3 12 to to M6 x 1 LSM-5 22 to to M8 x 1.25 LSM-7 48 to to M10 x 1.5 LOCK SCREWS for PROJECTED MOUNTING of Slip-Fixed Renewable Bushings $ 0.90 LSM-2 8 to to M5 x 0.8 LSM-4 12 to to M6 x 1 LSM-6 22 to to M8 x 1.25 LSM-8 48 to to M10 x 1.5 FLUSH ROUND CLAMPS for Slip-Fixed Renewable Bushings PROTRUDING ROUND CLAMP ROUND CLAMPS for STANDARD MOUNTING of Slip-Fixed Renewable Bushings $ 3.13 SFM BUSHING BODY DIAMETER A OUTSIDE DIAMETER B OVERALL HEIGHT C COUNTER- BORE DIA. D COUNTER- BORE DEPTH E SLOT DISTANCE F CLAMPING HEIGHT (+0.00 / ) MM (+.010 / -.000) IN. G RADIUS H HOLE DIAMETER (±0.2) MM (±.008) IN. RCM USE WITH SOCKET HEAD CAP SCREW NUMBER MM INCH MM INCH MM INCH MM INCH MM INCH MM INCH MM INCH MM INCH MM INCH THD SIZE RCM-1 8 to to M5 x 0.8 RCM-3 12 to to M6 x 1 RCM-5 22 to to M8 x 1.25 RCM-7 48 to to M10 x 1.5 ROUND CLAMPS for PROJECTED MOUNTING of Slip-Fixed Renewable Bushings $ 3.13 RCM-2 8 to to M5 x 0.8 RCM-4 12 to to M6 x 1 RCM-6 22 to to M8 x 1.25 RCM-8 48 to to M10 x WOODRUFF AVE. DOWNEY, CA TELEPHONE (562) / (800) IN CA / FAX (562) /(800) A35