D E S I G N G U I D E ICB REVISED 10 / 2018

Transcription

1 DESIGN GUIDE ICB REVISED 10 / 2018

2 T B L E O F C O N T E N T S 3 B U I L T- I N R E F R I G E R T I O N 30 P R O 4 8 R E F R I G E R T I O N 35 I N T E G R T E D R E F R I G E R T I O N 44 INE STORGE 72 SUB-ZERO RRNTIES Features and specifications are subject to change at any time without notice. Throughout this guide, dimensions may vary by ± 3.

3 BUILT-IN REFRIGERTION Built-In Refrigeration Sub-Zero designers and engineers continue to perfect the built-in line. The addition of LED lighting throughout and several new models with internal water dispensers, along with the same advanced food preservation technology Sub-Zero is known for, make the built-in line nothing short of revolutionary. BUILT-IN MODELS ICBBI-36R ICBBI-36F ICBBI-36UID ICBBI-36UFDID ICBBI-42UFDID ICBBI-36S ICBBI-42S ICBBI-42SD ICBBI-48S ICBBI-48SID ICBBI-48SD subzero.com 3

4 BUILT-IN REFRIGERTION Overall Dimensions LL REFRIGERTOR / LL FREEZER OVER-ND-UNDER HEIGHT DIMENSIONS ± HEIGHT DIMENSIONS ± Model ICBBI-36R, ICBBI-36F Model ICBBI-36UID Overall dimensions are based on stainless steel models. For flush inset applications, add 13 to the door clearance dimensions. 4 English

5 BUILT-IN REFRIGERTION Overall Dimensions OVER-ND-UNDER HEIGHT DIMENSIONS ± HEIGHT DIMENSIONS ± Model ICBBI-36UFDID Model ICBBI-42UFDID subzero.com 5

6 BUILT-IN REFRIGERTION Overall Dimensions SIDE-BY-SIDE HEIGHT DIMENSIONS ± HEIGHT DIMENSIONS ± Model ICBBI-36S Model ICBBI-42S, ICBBI-42SD 6 English

7 BUILT-IN REFRIGERTION Overall Dimensions SIDE-BY-SIDE Specifications INTERIOR CPCITY LL REFRIGERTOR / LL FREEZER R (L) F (L) ICBBI-36R 613 ICBBI-36F 612 OVER-ND-UNDER R (L) F (L) ICBBI-36UID ICBBI-36UFDID ICBBI-42UFDID SIDE-BY-SIDE R (L) F (L) ICBBI-36S ICBBI-42S ICBBI-42SD ICBBI-48S ICBBI-48SID ICBBI-48SD HEIGHT DIMENSIONS ± Model ICBBI-48S, ICBBI-48SID, ICBBI-48SD subzero.com 7

8 BUILT-IN REFRIGERTION Opening Dimensions STNDRD INSTLLTION 610 OPENING DEPTH 89 FINISHED RETURN 19 TYPICL TOP VIE FRMELESS CBINETRY 89 FINISHED RETURN 19 TYPICL FILLER 2127 OPENING HEIGHT OPENING IDTH FRMED CBINETRY SIDE VIE FRONT VIE NOTE: 89 finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit. OPENING IDTH ICBBI-36R, ICBBI-36F ICBBI-36UID, ICBBI-36UFDID, ICBBI-36S ICBBI-42UFDID, ICBBI-42S, ICBBI-42SD ICBBI-48S, ICBBI-48SID, ICBBI-48SD If a 2108 grille height is specified, the opening height must be decreased by 22. If a 2235 grille height is specified, the opening height must be increased by 102. If two units are installed side by side, refer to page 10 for dual standard installations. 8 English

9 BUILT-IN REFRIGERTION Opening Dimensions FLUSH INSET INSTLLTION 665 FLUSH INSET DEPTH 56 FINISHED CLETS FINISHED RETURN CLET 19 TYPICL TOP VIE FRMELESS CBINETRY FINISHED RETURN CLET FILLER 19 TYPICL 2134 FLUSH INSET HEIGHT FLUSH INSET IDTH FRMED CBINETRY SIDE VIE FRONT VIE NOTE: 89 finished returns and shaded areas will be visible and should be finished to match cabinetry. Shaded line represents profile of unit with 19 panel. FLUSH INSET IDTH ICBBI-36R, ICBBI-36F ICBBI-36UID, ICBBI-36S ICBBI-42S ICBBI-48S, ICBBI-48SID, ICBBI-48SD Dimensions assume a 19 panel thickness. If a 2108 grille height is specified, the flush inset height must be decreased by 22. If a 2235 grille height is specified, the flush inset height must be increased by 102. If two units are installed side by side, refer to page 11 for dual flush inset installations. subzero.com 9

10 BUILT-IN REFRIGERTION Opening Dimensions DUL STNDRD INSTLLTION 610 OPENING DEPTH 89 FINISHED RETURN 19 TYPICL TOP VIE FRMELESS CBINETRY 89 FINISHED RETURN 19 TYPICL FILLER 2127 OPENING HEIGHT OPENING IDTH FRMED CBINETRY SIDE VIE FRONT VIE NOTE: 89 finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit. OPENING IDTH Two 914 Models 1822 dual installation kit will be required for this installation. 10 English

11 BUILT-IN REFRIGERTION Opening Dimensions DUL FLUSH INSET INSTLLTION 665 FLUSH INSET DEPTH 56 FINISHED CLETS FINISHED RETURN CLET 19 TYPICL TOP VIE 6 32 FRMELESS CBINETRY FINISHED RETURN CLET FILLER 19 TYPICL 2134 FLUSH INSET HEIGHT FLUSH INSET IDTH FRMED CBINETRY SIDE VIE FRONT VIE NOTE: 89 finished returns and shaded areas will be visible and should be finished to match cabinetry. Shaded line represents profile of unit with 19 panel. FLUSH INSET IDTH Two 914 Models 1886 Dimensions assume a 19 panel thickness. dual installation kit will be required for this installation. subzero.com 11

12 BUILT-IN REFRIGERTION Electrical Requirements Installation must comply with all applicable electrical codes and be properly grounded (earthed). International models from the factory designed without a transformer require a V C, 50/60 Hz electrical supply, fused at the correct rating for the unit. If required by local or national codes, the power cord can be easily replaced using the power inlet device. The electrical supply should be located within the shaded area shown in the illustration below. separate circuit servicing only this appliance is required. ground fault circuit interrupter (GFCI) is not recoended and may cause interruption of operation. Plumbing Requirements Installation must comply with all applicable plumbing codes. For built-in models with an automatic ice maker, the water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self piercing valves. The water supply line must not interfere with installation of the anti-tip brackets. reverse osmosis system can be used provided there is constant water pressure of bar supplied to the unit at all times. copper line is not recoended for this application. ELECTRICL REQUIREMENTS Power Supply Circuit Breaker Receptacle V C, 50/60 Hz 10 amp grounding-type (earthed) PLUMBING REQUIREMENTS ater Supply Line ater Pressure Excess ater Line for Connection 6.4 OD copper line, braided stainless steel, or PEX tubing bar.9 m 178 E 152 RIGHT SIDE OF OPENING 1918 FROM FLOOR RIGHT SIDE OF OPENING Electrical supply location RE EXTENDS 13 FORRD ON FLOOR ater supply location English

13 BUILT-IN REFRIGERTION Custom Panels For overlay and flush inset applications, custom door panels must be provided. Handle hardware must also be provided for overlay and flush inset applications. Refer to panel requirements below and the charts on pages for custom panel dimensions for your specific design application. IMPORTNT NOTE: Do not cover a glass door with a solid panel. Finish all sides of the custom panels. They may be visible when the door is open or through the window of a glass door model. PNEL REQUIREMENTS PNEL EIGHT ICBBI-36R, ICBBI-36F ll Other Models Grille Panel MX 34 kg 23 kg 6 kg PNEL MOUNTING KIT Sub-Zero custom panel mounting kit eliminates the need for a backer and spacer panel and is avail able through an authorized Sub-Zero dealer. The kit consists of mounting cleats, screws, and gages used to properly position the cleats. The kit is available for all built-in models. Dual installations require two mounting kits. OVERLY PNELS Overlay panels are typically created by combining a 19 custom panel, a 3 spacer panel, and a 6 backer panel. Refer to the illustrations below. hen installing two units side by side, refer to page 10 for dual standard installations. PNEL THICKNESS MIN ll Panels 16 SPCER PNEL CUSTOM PNEL SPCER PNEL CUSTOM PNEL BCKER PNEL TRIM BCKER PNEL 8 min 3 (OVERLY) 19 TYPICL 3 6 Panel assembly cross section (overlay) Panel assembly rear view subzero.com 13

14 BUILT-IN REFRIGERTION Custom Panels FLUSH INSET PNELS The flush inset application is an overlay model with flush inset panels. It is not a separate model. The flush inset design allows custom panels to be installed flush with adjacent cabinets. Similar to overlay, flush inset panels are typically created by combining a 19 custom panel, a 3 spacer panel and a 6 backer panel. Refer to the illustrations for overlay panels. ICE ND TER DISPENSER For models ICBBI 42SD and ICBBI 48SD, the refrigerator door panel must include a cutout to accoodate the external dispenser. The bezel will accoodate a 19 thick panel. Panels thicker than 19 must be routed in the dispenser area to 29 (including backer and spacer panels). Refer to the illustration below. For flush inset panels thicker than 19, a 90 door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale templates at the end of this guide. hen installing two units side by side, refer to page 11 for dual flush inset installations Dispenser dimensions 14 English

15 BUILT-IN REFRIGERTION Overlay Panel Dimensions H H H H H ICBBI-36R, ICBBI-36F ICBBI-36UID MODEL ICBBI-36R, ICBBI-36F REFRIGERTOR / FREEZER H Overlay Panel Spacer Panel Backer Panel GRILLE H Overlay Panel * Spacer Panel Backer Panel MODEL ICBBI-36UID REFRIGERTOR H Overlay Panel Spacer Panel Backer Panel FREEZER H Overlay Panel Spacer Panel Backer Panel GRILLE H Overlay Panel * Spacer Panel Backer Panel *Panel height may be increased by 11 to hide the upper main frame. Grille panel dimensions are for a standard 2134 overall unit height. For a 2108 height, subtract 25 from the grille panel height dimensions and for a 2235 height, add 102. specific panel grille must be ordered for a 2108 or 2235 overall unit height. subzero.com 15

16 BUILT-IN REFRIGERTION Overlay Panel Dimensions H H H H B ICBBI-36S, ICBBI-42S, ICBBI-48S, ICBBI-48SID ICBBI-48SD MODEL ICBBI-36S REFRIGERTOR H Overlay Panel Spacer Panel Backer Panel FREEZER H Overlay Panel Spacer Panel Backer Panel GRILLE H Overlay Panel * Spacer Panel Backer Panel MODEL ICBBI-42S REFRIGERTOR H Overlay Panel Spacer Panel Backer Panel FREEZER H Overlay Panel Spacer Panel Backer Panel GRILLE H Overlay Panel * Spacer Panel Backer Panel MODEL ICBBI-48S, ICBBI-48SID, ICBBI-48SD REFRIGERTOR H Overlay Panel Spacer Panel Backer Panel FREEZER H Overlay Panel Spacer Panel Backer Panel GRILLE H Overlay Panel * Spacer Panel Backer Panel ICBBI-48SD H Dispenser Cutout Cutout Location *Panel height may be increased by 11 to hide the upper main frame. Grille panel dimensions are for a standard 2134 overall unit height. For a 2108 height, subtract 25 from the grille panel height dimensions and for a 2235 height, add 102. specific panel grille must be ordered for a 2108 or 2235 overall unit height. B 16 English

17 BUILT-IN REFRIGERTION Flush Inset Panel Dimensions H H H H H ICBBI-36R, ICBBI-36F ICBBI-36UID MODEL ICBBI-36R, ICBBI-36F REFRIGERTOR / FREEZER H Flush Inset Panel Spacer Panel Backer Panel GRILLE H Flush Inset Panel Spacer Panel Backer Panel MODEL ICBBI-36UID REFRIGERTOR H Flush Inset Panel Spacer Panel Backer Panel FREEZER H Flush Inset Panel Spacer Panel Backer Panel GRILLE H Flush Inset Panel Spacer Panel Backer Panel Grille panel dimensions are for a standard 2134 overall unit height. For a 2108 height, subtract 25 from the grille panel height dimensions and for a 2235 height, add 102. specific panel grille must be ordered for a 2108 or 2235 overall unit height. subzero.com 17

18 BUILT-IN REFRIGERTION Flush Inset Panel Dimensions H H H H B ICBBI-36S, ICBBI-42S, ICBBI-48S, ICBBI-48SID ICBBI-48SD MODEL ICBBI-36S REFRIGERTOR H Flush Inset Panel Spacer Panel Backer Panel FREEZER H Flush Inset Panel Spacer Panel Backer Panel GRILLE H Flush Inset Panel Spacer Panel Backer Panel MODEL ICBBI-42S REFRIGERTOR H Flush Inset Panel Spacer Panel Backer Panel FREEZER H Flush Inset Panel Spacer Panel Backer Panel MODEL ICBBI-48S, ICBBI-48SID, ICBBI-48SD REFRIGERTOR H Flush Inset Panel Spacer Panel Backer Panel FREEZER H Flush Inset Panel Spacer Panel Backer Panel GRILLE H Flush Inset Panel Spacer Panel Backer Panel DISPENSER (ICBBI-48SD) H Cutout Cutout Location Grille panel dimensions are for a standard 2134 overall unit height. For a 2108 height, subtract 25 from the grille panel height dimensions and for a 2235 height, add 102. specific panel grille must be ordered for a 2108 or 2235 overall unit height. B GRILLE H Flush Inset Panel Spacer Panel Backer Panel English

19 BUILT-IN REFRIGERTION Flush Inset Panels PNEL OFFSET TOP VIE TOP VIE The illustrations provide panel offsets and reveals for built-in models in a flush inset application. Refer to the chart below for reference to the illustrations. PNEL OFFSET DOOR / DRER / GRILLE BCKER SPCER CBINETRY DOOR DOOR LL REFRIGERTOR / LL FREEZER Door / Grille Sides Grille Top Grille Bottom / Door Top Door Bottom ILLUS C D F FLUSH INSET PNEL REVEL OVER-ND-UNDER Door / Drawer / Grille Sides Grille Top Grille Bottom / Door Top Door Bottom / Drawer Top Drawer Bottom SIDE-BY-SIDE Doors (hinge) / Grille Sides Doors (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom ILLUS C D E F ILLUS B C D F Illus. CBINETRY GRILLE Illus. B GRILLE DOOR SIDE VIE SIDE VIE Illus. C Illus. D DOOR 8 2 DOOR / DRER 16 8 DRER 4 8 SIDE VIE SIDE VIE 2 Illus. E Illus. F subzero.com 19

20 BUILT-IN REFRIGERTION Dual Installation If two units are installed side by side, a dual installation kit may be required. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 51 filler strip is recoended between the units. custom filler strip is required when installing two French door or side-by-side models. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below. For dual standard installations, panel dimensions are the same as for single installations. Refer to the charts on pages Panel dimensions and offsets for dual flush inset installations are listed on the following pages. Dual installation kits are available through an authorized Sub-Zero dealer. For questions regarding the installation, contact your authorized Sub-Zero dealer. ITHOUT FILLER STRIP FILLER STRIP Opposite hinges Same side hinges 20 English

21 BUILT-IN REFRIGERTION Dual Flush Inset Panel Dimensions H H H H H ICBBI-36R, ICBBI-36F ICBBI-36UID MODEL ICBBI-36R, ICBBI-36F REFRIGERTOR / FREEZER H Flush Inset Panel Spacer Panel Backer Panel GRILLE H Flush Inset Panel Spacer Panel Backer Panel MODEL ICBBI-36UID REFRIGERTOR H Flush Inset Panel Spacer Panel Backer Panel FREEZER H Flush Inset Panel Spacer Panel Backer Panel GRILLE H Flush Inset Panel Spacer Panel Backer Panel Grille panel dimensions are for a standard 2134 overall unit height. For a 2108 height, subtract 25 from the grille panel height dimensions and for a 2235 height, add 102. specific panel grille must be ordered for a 2108 or 2235 overall unit height. For dual wide grilles, refer to page 23. subzero.com 21

22 BUILT-IN REFRIGERTION Dual Installation DUL FLUSH INSET PNEL OFFSET TOP VIE TOP VIE The illustrations provide panel offsets and reveals for built-in models in a dual flush inset application. Refer to the chart below for reference to the illustrations. PNEL OFFSET DOOR / DRER / GRILLE BCKER SPCER CBINETRY DOOR DUL TRIM DOOR LL REFRIGERTOR / LL FREEZER Door (hinge) / Grille Sides Door (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom OVER-ND-UNDER Door (hinge) / Drawer / Grille Sides Door (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom / Drawer Top Drawer Bottom ILLUS B C D F ILLUS B C D E F FLUSH INSET PNEL Illus. 8 CBINETRY GRILLE Illus. B GRILLE 6 REVEL DOOR 2 8 SIDE VIE SIDE VIE Illus. C Illus. D DOOR 8 2 DOOR / DRER 16 8 DRER 4 8 SIDE VIE SIDE VIE 2 Illus. E Illus. F 22 English

23 BUILT-IN REFRIGERTION Dual Installation DUL IDE GRILLE dual wide grille spans the entire width of both units in a dual installation and is a part of a dual installation kit. For overlay and flush inset panel dimensions for the dual wide grille, refer to the charts. Dimensions listed are for a standard 2134 finished height. DUL IDE GRILLE OVERLY TO 914 MODELS H Overlay Panel Spacer Panel Backer Panel DUL IDE GRILLE FLUSH INSET TO 914 MODELS H Flush Inset Panel Spacer Panel Backer Panel subzero.com 23

24 BUILT-IN REFRIGERTION Side Panel The custom side panels must be a minimum of 610 deep and 13 thick. Routing will be necessary for the side panel to fit flush against the side of the unit. Refer to the illustrations below. hen installing a built-in unit with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through an authorized Sub-Zero dealer. 610 Standard Handles Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. Refer to the chart below for standard handle lengths for built-in models. HNDLE LENGTH TUBULR PRO Full Door Over-and-Under Door Drawer Drawer FRONT OF SIDE PNEL ROUT TO MIN FRME SIDE PNEL ROUTING 108 Routing detail ROUT TO 5 (OVER-ND-UNDER MODELS) OPTIONL TOE KICK CUT-OUT 67 Side panel dimensions 24 English

25 BUILT-IN REFRIGERTION Overlay Flush Inset Panels FULL-SCLE TEMPLTE Overlay and flush inset panels must be a minimum of 16 thick to support mounting the handle. Panel thickness does not include the backer and spacer panel. Mount the handle close to the opening edge of the door. DEPTH OF TUBULR ND PRO HNDLES PNEL 25 PNEL 19 PNEL 3 SPCER PNEL 6 BCKER PNEL DOOR Overlay and flush inset panel thickness subzero.com 25

26 BUILT-IN REFRIGERTION Overlay pplication FULL-SCLE TEMPLTE 606 TO RER OF UNIT OVERLL IDTH OF UNIT THICK PNEL 19 THICK OVERLY PNEL (TYPICL) 6 BCKER PNEL 0 25 SCLE 90 door opening (top view) 26 English

27 BUILT-IN REFRIGERTION Flush Inset pplication FULL-SCLE TEMPLTE For panels thicker than 19, a 90 door stop may be required to prevent interference with adjacent cabinets. 610 TO BCK LL SSUMES 19 FLUSH INSET PNEL THICKNESS 25 THICK PNEL 19 THICK FLUSH INSET PNEL (TYPICL) 6 BCKER PNEL 0 25 SCLE 110 door opening (top view) subzero.com 27

28 BUILT-IN REFRIGERTION FILLER STRIP 32 PPROX PROFILE OF STINLESS STEEL RPPED DOOR ND HNDLE DOOR CLOSED Dual Standard Installation FULL-SCLE TEMPLTE DOOR OPEN 110 Typical overlay or stainless steel dual installation with filler strip at maximum 110 door opening. Panel thickness may require a 90 door stop SCLE Dual standard installation (top view) 28 English

29 BUILT-IN REFRIGERTION FILLER STRIP PROFILE OF 19 FLUSH INSET PNEL ND TUBULR HNDLE DOOR CLOSED Dual Flush Inset Installation FULL-SCLE TEMPLTE DOOR OPEN 110 Typical flush inset dual installation with filler strip at maximum 110 door opening. Panel thickness may require a 90 door stop SCLE Dual flush inset installation (top view) subzero.com 29

30 PRO 48 REFRIGERTION PRO 48 Refrigeration Freshness finds unmistakable expression in the Sub-Zero PRO kg monument to food preservation equal parts sculpted metal design statement and culinary secret weapon. Its vast interior, like its bold exterior, is crafted of stainless steel. The PRO 48 is available with or without a glass door and may be either built in or freestanding. PRO 48 MODELS ICB648PRO ICB648PROG 30 English

31 PRO 48 REFRIGERTION Overall Dimensions PRO 48 MODELS HEIGHT DIMENSIONS ± INTERIOR CPCITY R (L) F (L) ICB648PRO ICB648PROG Models ICB648PRO, ICB648PROG subzero.com 31

32 PRO 48 REFRIGERTION Opening Dimensions STNDRD / FLUSH INSTLLTION D OPENING DEPTH 89 FINISHED RETURN 19 TYPICL TOP VIE FRMELESS CBINETRY 89 FINISHED RETURN 19 TYPICL FILLER H OPENING HEIGHT OPENING IDTH FRMED CBINETRY SIDE VIE FRONT VIE NOTE: 89 finished returns will be visible and should be finished to match cabinetry. OPENING DIMENSIONS H D Standard Flush For standard built-in installations, the face frame of the unit will extend 51 beyond cabinetry. For flush installations, the front of the face frame will be flush with surrounding cabinetry. 32 English

33 PRO 48 REFRIGERTION Electrical Requirements Installation must comply with all applicable electrical codes and be properly grounded (earthed). International models from the factory designed without a transformer require a V C, 50/60 Hz electrical supply, fused at the correct rating for the unit. If required by local or national codes, the power cord can be easily replaced using the power inlet device. The electrical supply should be located within the shaded area shown in the illustration below. separate circuit servicing only this appliance is required. ground fault circuit interrupter (GFCI) is not recoended and may cause interruption of operation. ELECTRICL REQUIREMENTS Power Supply Circuit Breaker Receptacle V C, 50/60 Hz 10 amp grounding-type (earthed) Plumbing Requirements Installation must comply with all applicable plumbing codes. The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self piercing valves. The water supply line must not interfere with installation of the anti-tip bracket. reverse osmosis system can be used provided there is constant water pressure of bar supplied to the unit at all times. copper line is not recoended for this application. PLUMBING REQUIREMENTS ater Supply ater Pressure Excess ater Line for Connection 6.4 OD copper line, braided stainless steel, or PEX tubing bar.9 m 178 E RIGHT SIDE OF OPENING FROM FLOOR RIGHT SIDE OF OPENING RE EXTENDS 13 FORRD ON FLOOR Electrical supply location ater supply location subzero.com 33

34 PRO 48 REFRIGERTION Standard Handles Refer to the chart below for standard handle lengths for PRO 48 models. HNDLE LENGTH TUBULR PRO Door N 703 Refrigerator Drawer N 506 Freezer Drawer N English

35 INTEGRTED REFRIGERTION Integrated Refrigeration ith custom front panels and hardware, Sub-Zero invented integrated columns, tall, and drawer models that disappear into the decor. Integrated units fit flush with other cabinets, making integrated refrigeration as practical and beautiful in the master suite, bar, or theatre room as in the kitchen. Model ICBID-24RO, approved for outdoor installations, is ideal for any outdoor kitchen. INTEGRTED MODELS ICBIC-18FI ICBIC-24R ICBIC-24FI ICBIC-24C ICBIC-30RID ICBIC-30FI ICBIC-36RID ICBIT-30RID ICBIT-30CIID ICBIT-36CIID ICBID-24RO ICBID-30RP ICBID-30CI subzero.com 35

36 INTEGRTED REFRIGERTION Specifications INTERIOR CPCITY Overall Dimensions COLUMN COLUMN R (L) F (L) ICBIC-18FI 230 ICBIC-24R 352 ICBIC-24FI 338 ICBIC-24C ICBIC-30RID 475 ICBIC-30FI 415 ICBIC-36RID 590 TLL R (L) F (L) ICBIT-30RID 397 ICBIT-30CIID ICBIT-36CIID * DRER R (L) F (L) ICBID-24RO 113 ICBID-30RP 138 ICBID-30CI IMPORTNT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. *2121 MIN TO 2146 MX B COLUMN B ICBIC-18FI ICBIC-24R, ICBIC-24FI, ICBIC-24C ICBIC-30RID, ICBIC-30FI ICBIC-36RID English

37 INTEGRTED REFRIGERTION Overall Dimensions TLL DRER * * *864 MIN TO 889 MX *2121 MIN TO 2146 MX DRER ICBID-24RO ICBID-30RP, ICBID-30CI B TLL B ICBIT-30RID, ICBIT-30CIID ICBIT-36CIID subzero.com 37

38 INTEGRTED REFRIGERTION Opening Dimensions INTEGRTED MODELS 635 OPENING DEPTH 654 FOR OUTDOOR MODEL TOP VIE OPENING DIMENSIONS COLUMN * H ICBIC-18FI ICBIC-24R, ICBIC-24FI, ICBIC-24C ICBIC-30RID, ICBIC-30FI ICBIC-36RID TLL * H ICBIT-30RID, ICBIT-30CIID ICBIT-36CIID DRER * H ICBID-24RO ICBID-30RP, ICBID-30CI *For stainless steel side panel accessory, add 25 per panel to opening width. H OPENING HEIGHT OPENING IDTH The depth of each integrated model is 610. llow for panel thickness when planning the finished opening depth. minimum 89 finished return is required on all sides of the opening 114 for the outdoor model. Framed cabinets will require additional finished filler material behind the face frame for a proper installation. Refer to the illustration. DUL INSTLLTION hen installing two units side by side in a dual installation, the opening width is the width of the two units added together. dual installation kit will be required for this installation. If a dual installation kit is not specified, a minimum 51 filler strip is required between the units. SIDE VIE FRONT VIE Dual installation kits are available through an authorized Sub-Zero dealer. For questions regarding the installation, contact your authorized Sub-Zero dealer. NOTE: 89 finished returns will be visible and should be finished to match cabinetry 114 for outdoor model. 89 FINISHED RETURN 19 TYPICL 89 FINISHED RETURN 19 TYPICL FILLER FRMELESS CBINETRY FRMED CBINETRY 38 English

39 INTEGRTED REFRIGERTION Electrical Requirements Installation must comply with all applicable electrical codes and be properly grounded (earthed). The electrical supply must be located within the shaded area shown in the illustration and chart below. separate circuit servicing only this appliance is required. IMPORTNT NOTE: For indoor models, a ground fault circuit interrupter (GFCI) is not recoended and may cause interruption of operation. For the outdoor model, a ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock. ELECTRICL REQUIREMENTS Power Supply Circuit Breaker Receptacle ELECTRICL SUPPLY LOCTION V C, 50/60 Hz 10 amp grounding-type (earthed) 457 Model Model Model Model 394 Plumbing Requirements Installation must comply with all applicable plumbing codes. The water supply line should be located within the shaded area shown in the illustration below. The water supply line should be connected to the house supply with an easily accessible shut-off valve. Do not use self piercing valves. The water supply line must not interfere with installation of the anti-tip bracket. reverse osmosis system can be used provided there is constant water pressure of bar supplied to the unit at all times. copper line is not recoended for this application. PLUMBING REQUIREMENTS ater Supply Line ater Pressure Excess ater Line for Connection TER SUPPLY LOCTION 6.4 OD copper line, braided stainless steel, or PEX tubing bar.9 m 457 Model Model Model Model 229 LEFT SIDE OF OPENING RIGHT SIDE OF OPENING E FLOOR Electrical supply location RE EXTENDS 13 FORRD ON FLOOR ater supply location subzero.com 39

40 INTEGRTED REFRIGERTION Stainless Steel Panels The outdoor model requires the use of Sub-Zero stainless steel outdoor accessory panels. Stainless steel panels are available through an authorized Sub Zero dealer. The thickness of the indoor stainless steel panels is 19 and outdoor stainless steel panels is 38. The depth of each integrated model is 610. llow for panel thickness when planning the finished opening depth. 3 reveals are typical, however, the reveal between the upper and lower outdoor stainless steel panels is 6 to accoodate the lock. Custom Panels For integrated models, custom door panels and handle hardware must be provided. Refer to the panel requirements chart and typical panel dimensions. The thickness of the custom panel can vary. minimum 16 thick panel is required, but the thickness can be increased provided it does not exceed the weight limit. The depth of each integrated model is 610. llow for panel thickness when planning the finished opening depth. Refer to the full-scale template on page 43. CUTION s reveals between cabinetry and the unit decrease, severe finger pinching can occur while door is closing. Finish all sides of the custom panels. They will be visible when the door/drawer is open. D-style handles are recoended. Door handles must be located near the edge of the panel opposite the hinge and should be centered top to bottom. Drawer handles must be located near the top edge of each panel. Stainless steel tubular and pro handles are avail able through an authorized Sub-Zero dealer. PNEL REQUIREMENTS COLUMN MX EIGHT 457 Model 20 kg 610 Model 27 kg 762 Model 34 kg 914 Model 34 kg TLL (DOOR) MX EIGHT 762 Model 22 kg 914 Model 27 kg DRER Drawer Panel PNEL THICKNESS ll Panels MX EIGHT 7 kg MINIMUM English

41 INTEGRTED REFRIGERTION Custom Panels TYPICL PNEL DIMENSIONS DOOR PNEL HEIGHT The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below DECORTIVE VLNCE CNNOT EXTEND BEYOND THIS PLNE DOOR PNEL Column Tall Drawer TO BCK OF UNIT Typical panel dimensions are based on a 2134 finished height for column and tall models and 876 for drawer models, with a 102 toe kick and 3 reveals. Panel dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the chart below for panel widths. HINGE PNEL IDTH 457 Model Model Model Model 908 Upper valance column and tall (side view) DUL INSTLLTION For dual installations, refer to the illustration for panel heights and the chart below for panel widths. PNEL IDTH DUL INSTLLTION 457 Model Model Model Model 910 subzero.com 41

42 INTEGRTED REFRIGERTION Custom Panels TOE KICK CLERNCE Indoor Models Only: The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. Toe kick heights from 51 to 98 require a reduced toe kick accessory available through an authorized Sub-Zero dealer. HINGE** VENTED LOUVERS Standard Handles Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. Refer to the chart below for standard handle lengths for integrated models. HNDLE LENGTH TUBULR PRO Column Door Tall Door Drawer Drawer Drawer TO BCK OF UNIT DOOR PNEL 51 * TO 152 FROM FLOOR 29 MX TOE KICK DJUSTMENT DECORTIVE TOE KICK CNNOT EXTEND BEYOND THIS PLNE *51 to 98 requires sales accessory. **Column models only. Toe kick (side view) 42 English

43 INTEGRTED REFRIGERTION Maximum Door Opening FULL-SCLE TEMPLTE s the panel width and/or depth increases, so does the potential for panel interference. Interference may be minimized by using the 90 door stop. 19 PNEL DOOR OPEN MXIMUM REVEL POTENTIL INTERFERENCE DOOR CLOSED 19 PNEL DJCENT CBINETRY POTENTIL INTERFERENCE 0 25 SCLE Maximum door opening (top view) subzero.com 43

44 INE STORGE ine Storage ine finds a well-deserved place of honor in a Sub-Zero wine storage unit. Every detail is designed to ensure better wine preservation. Cherrywood-faced racks, soft lighting, custom cabinetry if desired Sub-Zero helps make a wine collection an element of beauty in the home. INE STORGE MODELS ICB424G ICBU-24 ICB424FSG ICBU-24FS ICBI-18 ICBI-24 ICBI-30 ICBI-30R ICBS-30 ICBB English

45 INE STORGE Overall Dimensions MODEL ICB424G / ICBU-24 MODEL ICB424FSG / ICBU-24FS STORGE CPCITY BOTTLES (750 ML) ICB424G, ICBU ICB424FSG, ICBU-24FS 46 Freestanding models ICB424FSG and ICBU-24FS have a finished stainless steel exterior and handles. Overall dimensions for ICB424G and ICBU-24 are based on the stainless steel model. Refer to page 65 for door clearance information. subzero.com 45

46 INE STORGE Opening Dimensions MODEL ICB424G / ICBU-24 Overall Dimensions COLUMN OPENING DEPTH 114 TOP VIE 2134 * OPENING HEIGHT OPENING IDTH SIDE VIE FRONT VIE NOTE: 89 finished returns will be visible and should be finished to match cabinetry. *2121 MIN TO 2146 MX FINISHED RETURN 19 TYPICL 89 FINISHED RETURN 19 TYPICL FILLER 45 FRMELESS CBINETRY FRMED CBINETRY B OPENING IDTH ICB424G, ICBU DUL OPENING IDTH Two 610 Models Dual installation kit required COLUMN B ICBI ICBI ICBI English

47 INE STORGE Overall Dimensions TLL STORGE CPCITY COLUMN BOTTLES (750 ML) ICBI ICBI ICBI TLL R (L) BOTTLES (750 ML) ICBI-30R * *2121 MIN TO 2146 MX B TLL B ICBI-30R IMPORTNT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. subzero.com 47

48 INE STORGE Opening Dimensions INTEGRTED INE STORGE OPENING DIMENSIONS 635 OPENING DEPTH TOP VIE COLUMN * H ICBI ICBI ICBI TLL * H ICBI-30R *For stainless steel side panel accessory, add 25 per panel to opening width. The depth of each integrated (ICBI) model is 610. llow for panel thickness when planning the finished opening depth. minimum 89 finished return is required on all sides of the opening. Framed cabinets will require additional finished filler material behind the face frame for a proper installation. Refer to the illustration. H OPENING HEIGHT OPENING IDTH DUL INSTLLTION The unit can be installed next to an integrated refrigeration model or another integrated wine storage model in a dual installation. hen installing two units side by side, the opening width is the width of the two units added together. dual installation kit will be required for this installation. If a dual installation kit is not specified, a minimum 51 filler strip is required between the units. Dual installation kits are available through an authorized Sub-Zero dealer. For questions regarding the installation, contact your authorized Sub-Zero dealer. SIDE VIE FRONT VIE NOTE: 89 finished returns will be visible and should be finished to match cabinetry. 89 FINISHED RETURN 19 TYPICL 89 FINISHED RETURN FILLER FRMELESS CBINETRY FRMED CBINETRY 48 English

49 INE STORGE Overall Dimensions MODEL ICBS-30 / ICBB STORGE CPCITY BOTTLES (750 ML) ICBS ICBB HEIGHT DIMENSIONS ± Overall dimensions are based on the stainless steel model. For flush inset applications, add 13 to the door clearance dimensions. subzero.com 49

50 INE STORGE Opening Dimensions ICBS-30 / ICBB-30 STNDRD INSTLLTION 610 OPENING DEPTH 89 FINISHED RETURN 19 TYPICL TOP VIE FRMELESS CBINETRY 89 FINISHED RETURN 19 TYPICL FILLER 2127 OPENING HEIGHT OPENING IDTH FRMED CBINETRY SIDE VIE FRONT VIE NOTE: 89 finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit. OPENING IDTH ICBS-30 ICBB If a 2108 grille height is specified, the opening height must be decreased by 22. If a 2235 grille height is specified, the opening height must be increased by 102. If two units are installed side by side, refer to page 52 for dual standard installations. 50 English

51 INE STORGE Opening Dimensions ICBS-30 / ICBB-30 FLUSH INSET INSTLLTION 665 FLUSH INSET DEPTH 56 FINISHED CLETS FINISHED RETURN CLET 19 TYPICL TOP VIE FRMELESS CBINETRY FINISHED RETURN CLET FILLER 19 TYPICL 2134 FLUSH INSET HEIGHT FLUSH INSET IDTH FRMED CBINETRY SIDE VIE FRONT VIE NOTE: 89 finished returns and shaded areas will be visible and should be finished to match cabinetry. Shaded line represents profile of unit with 19 panel. FLUSH INSET IDTH ICBS-30 ICBB Dimensions assume a 19 panel thickness. If a 2108 grille height is specified, the flush inset height must be decreased by 22. If a 2235 grille height is specified, the flush inset height must be increased by 102. If two units are installed side by side, refer to page 53 for dual flush inset installations. subzero.com 51

52 INE STORGE Opening Dimensions ICBS-30 / ICBB-30 DUL STNDRD INSTLLTION 610 OPENING DEPTH 89 FINISHED RETURN 19 TYPICL TOP VIE FRMELESS CBINETRY 89 FINISHED RETURN 19 TYPICL FILLER 2127 OPENING HEIGHT OPENING IDTH FRMED CBINETRY SIDE VIE FRONT VIE NOTE: 89 finished returns will be visible and should be finished to match cabinetry. Shaded line represents profile of unit. OPENING IDTH ICBS-30 and 762 Built-In ICBB-30 and 762 Built-In ICBS-30 and 914 Built-In ICBB-30 and 914 Built-In dual installation kit will be required for this installation. 52 English

53 INE STORGE Opening Dimensions ICBS-30 / ICBB-30 DUL FLUSH INSET INSTLLTION 665 FLUSH INSET DEPTH 56 FINISHED CLETS FINISHED RETURN CLET 19 TYPICL TOP VIE 6 32 FRMELESS CBINETRY FINISHED RETURN CLET FILLER 19 TYPICL 2134 FLUSH INSET HEIGHT FLUSH INSET IDTH FRMED CBINETRY SIDE VIE FRONT VIE NOTE: 89 finished returns and shaded areas will be visible and should be finished to match cabinetry. Shaded line represents profile of unit with 19 panel. FLUSH INSET IDTH ICBS-30 and 762 Built-In ICBB-30 and 762 Built-In ICBS-30 and 914 Built-In ICBB-30 and 914 Built-In Dimensions assume a 19 panel thickness. dual installation kit will be required for this installation. subzero.com 53

54 INE STORGE Electrical Requirements Installation must comply with all applicable electrical codes and be properly grounded (earthed). The electrical supply must be located within the shaded area shown in the illustration for your specific model. For integrated (ICBI) models, also refer to the chart. separate circuit servicing only this appliance is required. ground fault circuit interrupter (GFCI) is not recoended and may cause interruption of operation. If the unit will be connected to a home security system, allow 914 of excess wiring for proper connection. ELECTRICL SUPPLY LOCTION ICBI-18 ICBI-24 ICBI-30, ICBI 30R LEFT SIDE OF OPENING ELECTRICL REQUIREMENTS Power Supply V C, 50/60 Hz 114 Circuit Breaker Receptacle 10 amp grounding-type (earthed) 6 E FLOOR 108 Integrated (ICBI) models LEFT SIDE OF OPENING 178 E E FROM FLOOR FLOOR RIGHT SIDE OF OPENING Model ICB424G, ICBU-24 Model ICBS-30, ICBB English

55 INE STORGE Custom Panels For overlay, integrated, and flush inset applications, custom door panels must be provided. Handle hardware must also be provided for overlay, integrated, and flush inset applications. Refer to the panel requirements and custom panel dimensions charts for your specific model and design application. Custom Panel ICB424G ICBU-24 For models ICB424G and ICBU-24, the custom door panel will attach directly to the door frame with screws through a series of pre-drilled holes. Refer to the charts below for panel requirements and dimensions. Do not install a solid panel on a glass door unit. solid door is available as a sales accessory (except models ICBS 30 and ICBB-30) and must be installed if a solid panel is specified. Service may be required to install the door. Contact an authorized Sub-Zero dealer for more information. Overall dimensions are the same for glass door and solid door panels. Finish all sides of the custom panels. They may be visible when the door is open or through the window of a glass door model. PNEL REQUIREMENTS PNEL EIGHT ICB424G, ICBU-24 PNEL THICKNESS ICB424G, ICBU-24 OVERLY PNEL DIMENSIONS MX 5 kg MIN 16 Models ICB424FSG and ICBU-24FS have a finished stainless steel exterior that is designed to be used in a freestanding application. H ICB424G, ICBU-24 PNEL DIMENSIONS MODEL H ICB424G, ICBU STILES / RILS Minimum 57 DOOR CLERNCE Models ICB424G and ICBU-24 can be installed flush with surrounding cabinetry. Depending on the thickness of the overlay door panel, it may be necessary to install the unit 6 beyond the front surface of adjacent cabinetry to prevent interference when the door is opened to 145. Refer to the full-scale template on page 65. subzero.com 55

56 INE STORGE Custom Panels Integrated Models For integrated (ICBI) models, custom door panels and handle hardware must be provided. Refer to the panel requirements chart and typical panel dimensions. Do not install a solid panel on the glass door unit. solid door is available as a sales accessory through an authorized Sub-Zero dealer. The thickness of the custom panel can vary. minimum 16 thick panel is required, but the thickness can be increased provided it does not exceed the weight limit. The depth of each integrated model is 610. llow for panel thickness when planning the finished opening depth. Refer to the full-scale template on page 43. TYPICL PNEL DIMENSIONS CUTION s reveals between cabinetry and the unit decrease, severe finger pinching can occur while door is closing. Column Tall Finish all sides of the custom panels. They will be visible when the door/drawer is open. D-style handles are recoended. Door handles must be located near the edge of the panel opposite the hinge and should be centered top to bottom. Drawer handles must be located near the top edge of each panel. Stainless steel tubular and pro handles are avail able through an authorized Sub-Zero dealer. Typical panel dimensions are based on a 2134 finished height, 102 toe kick, and 3 reveals. Panel dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the chart below for panel widths. PNEL IDTH ICBI-18 ICBI PNEL REQUIREMENTS ICBI-30, ICBI-30R 756 STILES / RILS Stiles Top Rail Bottom Rail Bottom Rail (ICBI-30R) IDTH DUL INSTLLTION For dual installations, refer to the illustration for panel heights and the chart below for panel widths. PNEL EIGHT Door Frame MX 16 kg PNEL IDTH DUL INSTLLTION Door Frame (ICBI-30R) 11 kg ICBI Drawer Panel 7 kg ICBI PNEL THICKNESS ll Panels MIN 16 ICBI-30, ICBI-30R English

57 INE STORGE Custom Panels Integrated Models DOOR PNEL HEIGHT The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below. TOE KICK CLERNCE The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. Toe kick heights from 51 to 98 require a reduced toe kick accessory available through an authorized Sub-Zero dealer DOOR PNEL DECORTIVE VLNCE CNNOT EXTEND BEYOND THIS PLNE 610 TO BCK OF UNIT HINGE** DOOR PNEL VENTED LOUVERS 610 TO BCK OF UNIT HINGE 51 * TO 152 FROM FLOOR 29 MX TOE KICK DJUSTMENT DECORTIVE TOE KICK CNNOT EXTEND BEYOND THIS PLNE Upper valance column and tall (side view) *51 to 98 requires sales accessory. **Column models only. Toe kick (side view) subzero.com 57

58 INE STORGE Custom Panels ICBS-30 ICBB-30 OVERLY PNELS OVERLY PNEL DIMENSIONS Overlay panels are typically created by combining a 19 custom panel, a 3 spacer panel, and a 6 backer panel. Refer to the illustrations below. H PNEL REQUIREMENTS PNEL EIGHT MX H Door 34 kg Grille 6 kg PNEL THICKNESS MIN Overlay 16 SPCER PNEL CUSTOM PNEL SPCER PNEL ICBS-30, ICBB-30 CUSTOM PNEL BCKER PNEL 3 TRIM DOOR FRME 8 min GLSS Panel assembly cross section (overlay) 19 TYPICL 3 BCKER PNEL 6 Panel assembly rear view OVERLY PNELS DOOR H Overlay Panel Spacer Panel Backer Panel STILES / RILS Minimum 83 GRILLE H Overlay Panel * Spacer Panel Backer Panel *Panel height may be increased by 11 to hide the upper main frame. Grille panel dimensions are for a standard 2134 overall unit height. For a 2108 height, subtract 25 from the grille panel height dimensions and for a 2235 height, add 102. specific panel grille must be ordered for a 2108 or 2235 overall unit height. 58 English

59 INE STORGE Custom Panels ICBS-30 ICBB-30 FLUSH INSET PNELS FLUSH INSET PNEL DIMENSIONS The flush inset application is an overlay model with flush inset panels. It is not a separate model. H The flush inset design allows custom panels to be installed flush with adjacent cabinets. Similar to overlay, flush inset panels are typically created by combining a 19 custom panel, a 3 spacer panel, and a 6 backer panel. Refer to the illustrations for overlay panels on the previous page. H For flush inset panels thicker than 19, a 90 door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale template on page 68. PNEL REQUIREMENTS PNEL EIGHT Door Grille PNEL THICKNESS Flush Inset MX 34 kg 6 kg MIN 16 ICBS-30, ICBB-30 FLUSH INSET PNELS DOOR H Flush Inset Panel Spacer Panel Backer Panel STILES / RILS Minimum 95 GRILLE H Flush Inset Panel Spacer Panel Backer Panel Grille panel dimensions are for a standard 2134 overall unit height. For a 2108 height, subtract 25 from the grille panel height dimensions and for a 2235 height, add 102. specific panel grille must be ordered for a 2108 or 2235 overall unit height. subzero.com 59

60 INE STORGE Custom Panels ICBS-30 ICBB-30 FLUSH INSET PNEL OFFSET TOP VIE The illustrations provide panel offsets and reveals for model ICBS-30 or ICBB-30 in a flush inset application. Refer to the chart below for reference to the illustrations. PNEL OFFSET Door / Grille Sides Grille Top Grille Bottom / Door Top Door Bottom ILLUS B C D DOOR / DRER / GRILLE BCKER SPCER FLUSH INSET PNEL 8 CBINETRY CBINETRY GRILLE SIDE VIE Illus. Illus. B GRILLE 8 4 DOOR / DRER 13 8 DOOR 2 8 SIDE VIE SIDE VIE 2 Illus. C Illus. D 60 English

61 INE STORGE Custom Panels ICBS-30 ICBB-30 DUL INSTLLTIONS DUL FLUSH INSET PNEL DIMENSIONS dual installation kit may be required if two models ICBS-30 or a model ICBS-30 and a built-in unit are installed side by side, or two models ICBB-30 or a model ICBB-30 and a built-in unit. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 51 filler strip is recoended between the units. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below. H H Dual installation kits are available through an authorized Sub-Zero dealer. For questions regarding the installation, contact your authorized Sub-Zero dealer. For dual standard installations, panel dimensions are the same as for single installations. Panel dimensions and offsets for dual flush inset installations are listed on the following pages. ICBS-30, ICBB-30 DUL FLUSH INSET PNELS DOOR H Flush Inset Panel Spacer Panel Backer Panel STILES / RILS Minimum 95 GRILLE H Flush Inset Panel Spacer Panel Backer Panel ITHOUT FILLER STRIP Opposite hinges FILLER STRIP Same side hinges Grille panel dimensions are for a standard 2134 overall unit height. For a 2108 height, subtract 25 from the grille panel height dimensions and for a 2235 height, add 102. specific panel grille must be ordered for a 2108 or 2235 overall unit height. subzero.com 61

62 INE STORGE Custom Panels ICBS-30 ICBB-30 DUL FLUSH INSET PNEL OFFSET TOP VIE TOP VIE The illustrations provide panel offsets and reveals for model ICBS-30 or ICBB-30 in a dual flush inset application. Refer to the chart below for reference to the illustrations. PNEL OFFSET ILLUS DOOR / DRER / GRILLE BCKER SPCER CBINETRY DOOR DUL TRIM DOOR Door (hinge) / Grille Sides Door (handle) Sides Grille Top Grille Bottom / Door Top B C D FLUSH INSET PNEL REVEL Door Bottom E Illus. Illus. B CBINETRY 13 GRILLE 8 4 GRILLE DOOR 2 8 SIDE VIE SIDE VIE Illus. C Illus. D DOOR / DRER 8 SIDE VIE 2 Illus. E 62 English

63 INE STORGE Custom Panels ICBS-30 ICBB-30 SIDE PNEL The custom side panel must be a minimum of 610 deep and 13 thick. Routing will be necessary for the side panel to fit flush against the side of the unit. Refer to the illustrations below. hen installing model ICBS-30 or ICBB-30 with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through an authorized Sub-Zero dealer. 610 FRONT OF SIDE PNEL Standard Handles Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. Refer to the chart below for standard handle lengths for wine storage models. HNDLE LENGTH TUBULR PRO ICB424G Door ICBU-24 Door ICBI-18 Door ICBI-24 Door ICBI-30 Door ICBI-30R Door ICBI-30R Drawer ICBS-30 Door ICBB-30 Door ROUT TO MIN FRME SIDE PNEL ROUTING Routing detail 102 OPTIONL TOE KICK CUT-OUT 67 Side panel dimensions subzero.com 63

64 INE STORGE ine Rack ood Facing FULL-SCLE TEMPLTE The natural cherrywood facing on wine storage racks can be stained and sealed, or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale template below for profile dimensions of the wood facing and the chart for the width. OOD FCING IDTH ICB424G, ICBU-24 ICB424FSG, ICBU-24FS ICBI-18 ICBI-24 ICBI-30, ICBI-30R ICBS-30, ICBB-30 IDTH ICBI-18, ICBI-24, ICBI-30, ICBI-30R ICB424G, ICBU-24, ICB424FSG, ICBU-24FS ICBS-30, ICBB-30 ine rack wood facing profile 64 English