Specification 8-cylinder-V-tpye-engine

Transcription

1 Specification 8-cylinder-V-tpye-engine engineering: Technische Daten: layout: cylinder capacity: stroke/bore: weight: speed.: overall length: overall width: overall hight: propeller: Dipl.-Ing. Volker Jung, Fa. CAD+Modelltechnik Jung 8-cylinder-V-tpye-engine with twin carburetor, crankshaft with six bearings supported, per one above lying camshaft per cylinder side, camshaft with two bearings supported, valves operated with hut follower ~132 cm³ (8 x 16.5 ccm) 25 mm / 29 mm ca. 5,2 kg /min 297 mm 172 mm 139 mm 26 x 16 Zoll Passing on as well as copy this and the following documents, utilization and communication of his contents are forbidden as far as not allowed particularly. Contraventions commit to doing compensation. Reserving all rights for the patent and registered design entry in case. Subject to change without notice. 1

2 8-cylinder-V-engine, 132 ccm bill of materials dimensions part-no. pcs. name A x B x L material remark, standardize, supplier 01 4 inlet manifold 1 10 x 0,3 x ~120 high-grade steel pipe according drawing 02 2 inlet manifold 2 10 x 0,3 x ~150 high-grade steel pipe according drawing 03 8 exhaust manifold 10 x 0,3 x ~125 high-grade steel pipe according drawing 04 1 bolt, for tension pulley 10 x 14,3 Al-Cu-Mg-Pb; F according drawing 05 1 distance bush 1, for camshaft left 7 x Al-Cu-Mg-Pb; F according drawing 06 1 distance bush 2, for camshaft right 7 x Al-Cu-Mg-Pb; F according drawing 07 1 vent nipple SW 7 x 17 brass according drawing spring plate 9,5 x 1,5 silver steel according drawing 09 2 threaded bolt, for tension pulley M 4 x 27,5 silver steel according drawing 10 8 glow plug steel modeling specialist shop hut follower silver steel according drawing 12 8 piston 29 x 22 Al-Mg-Si 0,5; F22 according drawing piston pin cap 7 x 3 teflon according drawing 14 8 piston pin 7 x 26 steel, St60 DIN 6325 standard part, adapt according to drawing 15 8 piston ring 30,1 x 1,5 steel, C45 according drawing 16 1 crank case cap, back part 50 x 50 x 13 Al-Cu-Mg-Pb; F according drawing 17 3 crank case, middle part 41 x 16 Al-Cu-Mg-Pb; F according drawing 18 1 crank case, top part 50 x 50 x 216 Al-Cu-Mg-Pb; F according drawing 19 1 crank case, bottom part 50 x 50 x 216 Al-Cu-Mg-Pb; F according drawing 20 1 crank case, front part 50 x 50 x 48 Al-Cu-Mg-Pb; F according drawing 21 1 crank, back part 40 x 25,0 steel, C45 according drawing 22 3 crank, middle part 1 40 x 17,8 steel, C45 according drawing 23 3 crank, middle part 2 40 x 17,8 steel, C45 according drawing 24 1 crank, front part 40 x 134,0 steel, C45 according drawing 25 4 crank bolt 8 x 37,6 steel, St60 hardened DIN 6325 standard part, adapt according to drawing 26 4 bearing, 04x13x x 13 x 5 steel company Techpro 27 4 bearing, 05x13x x 13 x 5 steel company Techpro 28 6 bearing, 12x21x x 21 x 7 steel company Techpro 29 2 bearing, 12x28x x 28 x 8 steel company Techpro 30 1 bearing, 15x32x x 32 x 9 steel company Techpro 31 2 bearing, F08x16x5-688 (with flange) 8 x 16 x 5 steel company Techpro 32 4 bearing support, camshaft 15,5 x 5 x 28 Al-Cu-Mg-Pb; F according drawing 33 2 assembly bracket 25 x 12 x 182 Al-Cu-Mg-Pb; F according drawing 34 2 nut M 4 steel, galvanized DIN 934 standard part 35 8 needle bearing 8 x 12 x 10 steel company INA 36 8 camshaft 12,4 x 33,5 steel, C60, hardening according drawing 37 1 fit-in key 3 x 15 steel DIN 6885 standard part 38 8 rod 15,5 x 10 x 60,25 Al-Mg-Si 0,5; F22 according drawing 39 1 propeller driver 45 x 14,5 Al-Cu-Mg-Pb; F according drawing 40 1 washer 4 x 10 x 1 St, Alu hexagon socket set screw M 4 x 12 steel, 10.8 modeling specialist shop hexagon socket set screw M 4 x 4 steel, 10.8 DIN 914 standard part, (cutting ring) bill of materials, Rev. 2 (C) by V. Jung

3 8-cylinder-V-engine, 132 ccm dimensions part-no. pcs. name A x B x L material remark, standardize, supplier 43 4 hexagon socket set screw M 4 x 5 steel, 10.8 DIN 912 standard part 44 6 socket screw M 3 x 40 steel, 8.8 DIN 912 standard part 45a 1 socket screw M 4 x 5 steel, 8.8 DIN 912 standard part, shorted to 5 mm socket screw M 4 x 10 steel, 8.8 DIN 912 standard part 46 8 socket screw M 4 x 15 steel, 8.8 DIN 912 standard part, head trimming socket screw M 4 x 12 steel, 8.8 DIN 912 standard part, head trimming to 6,0 mm 48 8 socket screw M 4 x 14 steel, 8.8 DIN 912 standard part, shorted to 14 mm 49a 12 socket screw M 4 x 18 steel, 8.8 DIN 912 standard part, shorted to 18 mm 49 3 socket screw M 4 x 20 steel, 8.8 DIN 912 standard part countersunk socket screw M 3 x 20 steel, 8.8 DIN 912 standard part 51 6 countersunk socket screw M 4 x 10 steel, 8.8 DIN 7991 standard part 52 1 countersunk socket screw M 4 x 12 steel, 8.8 DIN 7991 standard part 53 9 countersunk socket screw M 5 x 12 steel, 8.8 DIN 7991 standard part 54 1 countersunk socket screw M 5 x 20 steel, 8.8 DIN 7991 standard part 55 1 tension pulley 23 x 11,5 Al-Cu-Mg-Pb; F according drawing 56 1 spinner 45 x 45,3 Al-Cu-Mg-Pb; F according drawing valve 11,5 x 27 high-grade steel, X15Cr12 according drawing valve spring 8,8 x 0,8 x 14,5 spring steel order no. D-123 company INA valve cap 13 x 20 red brass RG7 according drawing 60 2 carburator for 10 ccm 2-stroke engine 61 2 adapter for carburator 20 x 15 silver steel according drawing 62 8 screw connection, inlet manifold SW 12 x 20 steel according drawing 63 8 screw connection, exhaust manifold SW 12 x 19 steel according drawing 64 1 axle, for camshaft left 5 228,5 silver steel according drawing (see part 36) 65 1 axle, for camshaft right 5 232,5 silver steel according drawing (see part 36) shaft locking clip shim, 3mm spring steel DIN 6799 standard part 67 2 shaft locking clip shim, 4mm spring steel DIN 6799 standard part 68 1 tooth belt, teeth, profil 3M, 513 mm neoprene, 9 mm wide order no company Mädler 69 2 toothed belt wheel, 32 teeth, profil 3M aluminium order no company Mädler, adapt according to drawing 70 1 toothed belt wheel, 16 teeth, profil 3M aluminium order no company Mädler, adapt according to drawing 71 4 cylinder, left 50 x 50 x 42,5 Al-Cu-Mg-Pb; F according drawing 72 4 cylinder, right 50 x 50 x 42,5 Al-Cu-Mg-Pb; F according drawing 73 4 cylinder head, left 50 x Al-Cu-Mg-Pb; F according drawing 74 4 cylinder head, right 50 x Al-Cu-Mg-Pb; F according drawing 75 8 cylinder head gasket 34 x 29 x 0,2 Al-sheet modeling specialist shop 76 8 cylinder liner 34 x 47,5 ductile graphite iron according drawing sum 472 definition: WS = wrench size M = metrical thread DIN = german industry standard bill of materials, Rev. 2 (C) by V. Jung

4 8-cylinder V-engine, 132 ccm www-cad-modelltechnik-jung.com proof of delivery company part internet GW-Werkzeuge screw tap 1/4", 32 UNF Gutekunst GmbH springs Mädler GmbH gears usw. Metallverkaufsgesellschaft mbh aluminium (semi-finished products) Techpro GmbH (Fa. Eisenberg) ball bearing Toni Clark steel pipe (thin-walled), propeller Kistenpfennig AG needle bearing (company INA) Krumscheid muffler piston, piston ring, valve, CAD+Modelltechnik Jung all standard parts proof of delivery, Rev. 2 (C) by V. Jung

5 CAD und Modelltechnik Jung Schutzvermerk DIN34 beachten overall dimensions 8-cylinder-V-tpye-engine, 132 ccm pg. 1/1 rev. 2

6 , Schutzvermerk DIN34 beachten Bl. pg. 1/ CAD und Modelltechnik Jung 8-cylinder-V-tpye-engine, 132 ccm sc. 1 : front view section, between cylinder 1 and 2 1 rev. 2

7 10 M ,01 1,5 14,3 0,1 x 45 Al-Cu-Mg-Pb part 04 CAD + Modelltechnik Jung Copyright by "CAD+Modelltechnik Jung" bolt for tension pulley pg. 1/1 8-cylinder-V-tpye-engine, 132 ccm sc. 2 : 1 rev. 1

8 23 5 5h7 6 +0, ,75 26,95 5h7 6 +0, drill with parts 69 (thread M4) Al-Cu-Mg-Pb part 05, 06 Copyright by "CAD+Modelltechnik Jung" pg. 1/1 CAD + Modelltechnik Jung distance bushes 1 and 2 (part 05 and 06) 8-cylinder-V-tpye-engine, 132 ccm sc. 2 : 1 rev. 1

9 ( 70,7 ) 65,05 2) 1) = counterbore 4/8,6 mm 2) = counterbore 4/8,6 mm from backside 3) = drill 4 mm 4) = thread M4 A 41 A 3) 20 25, , a 26 1) q 50 8 x 45 4) , SCHNITT A-A 24 Al-Cu-Mg-Pb part 16 CAD + Modelltechnik Jung 16 Copyright by "CAD+Modelltechnik Jung" crank case cap, back part pg. 1/1 8-cylinder-V-tpye-engine, 132 ccm sc. 1 : 1 rev. 3

10 A 7 7 SCHNITT A-A ,01-0,02 19 A M5, drill with parts 18/ ( 10 ) 41 * * adapting outside diameters to the exact actual size of parts 18/19 Al-Cu-Mg-Pb part 17 CAD + Modelltechnik Jung Copyright by "CAD+Modelltechnik Jung" crank case, middle part pg. 1/1 8-cylinder-V-tpye-engine, 132 ccm sc. 1 : 1 rev. 1