Brochure LED Power Driver Tester

Transcription

1 Brochure LED Power Driver Tester (WT2080) Global Office of Lisun Electronics Inc. Lisun Group (Hong Kong) Limited Add: Room C, 15/F Hua Chiao Commercial Center, 678 Nathan Road, Mongkok, Kowloon, Hong Kong Tel: Fax: Lisun Electronics (Shanghai) Co., Ltd Add: , No. 1 Building, Nanxiang Zhidi Industry Park, No. 1101, Huyi Road, Jiading District, Shanghai, , China Tel: +86(21) Fax: +86(21) SalesSH@Lisungroup.com Chapter 1 Summarize ( 大标题, 居中小三加粗, 尽量在新一页, 用 Chapter 区分 ) Lisun Electronics Inc. (USA) Add: 1. Operating 445 S. Figueroa instruction Street, Los Angeless, ( 一级标题 CA, 90071, 左对齐小四加粗 U.S.A. ) According Sales@Lisungroup.com to the requirements of CIE, IESNA and the National s standard, this system is a multi-measurement mode spectrophotometer system which can realize Lisun B-β, A-α China and Factory C-γ etc through rotating lamps and lanterns. Add: NO. 37, Xiangyuan Road, Hangzhou City, Zhejiang Province, China Tel: It test Spatial, light intensity distribution curves on any cross section (can be shown under Engineering@Lisungroup.com the rectangular coordinate system or polar coordinate system), spatial iso-intensity curve. ( 正文, 段首顶格左对齐 10 号, 段落之间空行 ) 1.1 Explosive material ( 二级标题, 左对齐五号加粗 ) Lead in CFL & LED Test Instruments According to the requirements of CIE, IESNA and the National s standard, this Rev. 1/17/2019

2 Lisun Electronics Inc. Introduction WT2080 LED Power Driver Test Instrument is the comprehensive test instrument for LED drive power which is according to GB/T and IEC 62384:2006. It can measure the following parameters: Input Characteristics Test (AC&DC), Output Characteristics Test (AC&DC), Input Start Characteristics Test (DC) WT2080 can print data and communicate with PC, displaying all the dates and curves in PC Function 1. Input Characteristics Test (AC) To measure the input voltage, current, power, power factor, power grid frequency, total harmonic and the harmonic component of 0 ~ 50 times, wave ratio, initial phase angle, peak phase angle, the phase Angle. The fundamental frequency scope of the current and voltage : 45Hz~65Hz; Narrowband range: 45 Hz ~ 5 khz; Broadband range: 45 Hz ~ 1 MHz. range: 3 ~ 300 V (CF = 1.67); range: 5mA ~ 2.7A (CF = 3); Power range: ~ 800 W; Power factor range: ~ Input Characteristics Test (DC) Measuring voltage, current, power. range: 3~500V; range: 5mA~8A; Power range: 0.015~4000W 3. Output Characteristics Test (AC) Measuring lamp voltage, lamp current, and lamp power. Lamp voltage range: 3~300V(CF=3); Lamp current range: 5mA~2.7A(CF=3); Lamp power range: 0.015~800W -Page 1 -

3 Lisun Electronics Inc Output Characteristics Test (DC) Measuring output lamp voltage, lamp current, lamp power, ripple wave current. range: 3~500V; range: 5mA~8A; Power range: 0.015~4KW; Ripple wave current range: 5mA~2.5A 5. Output Start Characteristics Test (DC) Change curve and data of the measuring lamp voltage and lamp current within 0~2 seconds. Lamp voltage range: 3~500V; Lamp current range: 5mA~8A Specification AC: Items Basic error Measurement condition ±(0.1%read+0.1%range+1bit) Power Power Factor ±( /read+1bit) Input waveforms: sine wave; Input frequency: 45Hz ~ Frequency ±0.1%read 65Hz; Harmonic Wave (Valuable) ±(0.1%range+5%read) Lamp Input waveforms: sine Lamp Lamp Power ±(0.1%read+0.1%range+1bit) wave; Input frequency: 45Hz~ 65Hz; DC: Item Basic error Measurement condition Power Lamp Lamp Lamp Power ±(0.1%read+0.1%range+1bit) DC signal ±(0.1%read+0.1%range+1bit) DC signal Ripple ±2.5%range 20~70KHz The Next Pages are the Test Report from WT2080 -Page 2 -

4 Page 1 of 6 Pages Input Characteristics Test Report [Narrow Band] (V) (A) Power 44.12(W) Power Factor Frequency 49.97(Hz) Start Phase: 14.1 Peak Phase: 63.3 End Phase: Vthd(IEC): 3.6% Athd(IEC): 50.2% Spectrum(k) 0 0.0% 0.0% % 100.0% 2 0.1% 0.8% 3 1.8% 18.7% 4 0.2% 3.4% 5 2.9% 19.1% 6 0.1% 0.4% 7 0.5% 14.8% 8 0.1% 1.9% 9 0.3% 20.7% % 0.4% % 16.0% % 0.5% % 16.0% % 0.8% % 3.7% % 0.5% % 4.8% % 1.0% % 10.3% % 0.9% % 10.6% % 0.9% % 5.9% % 1.0% % 4.3% % 1.0% % 6.1% % 1.1% % 6.3% % 0.6% % 7.8% % 0.8% % 5.3% % 0.3% % 3.2% % 1.5% % 1.7% % 0.9% % 5.7%

5 Page 2 of 6 Pages Input Characteristics Test Report [Narrow Band] (V) (A) Power 44.12(W) Power Factor Frequency 49.97(Hz) Sensitivity: V/Div Peak: V Sensitivity: A Peak: A Start Phase: 14.1 Peak Phase: 63.3 End Phase: Spectrum THD(IEC): 3.56% H3: 1.82% H5: 2.92% H7: 0.51% H9: 0.28% Spectrum THD(IEC): 50.2% H3: 18.69% H5: 19.07% H7: 14.84% H9: 20.67%

6 Page 3 of 6 Pages Input Characteristics Test Report [Narrow Band] (Cont.) : (V) VCF: Vthd(IEC): 3.56% Spectrum : (A) ACF: Athd(IEC): 50.18% Spectrum Spectrum(k) Rel. Abs.(V) Spectrum(k) Rel. Abs.(A) % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % % %

7 Page 4 of 6 Pages Start characteristics Lamp Wave 0.690(s) 55.69(V) Lamp (rms) Sensitivity: V/Div Peak : V Time Sensitivity: 200 ms/div Time to peak: s Lamp Wave 0.690(s) (A) Lamp (rms) Sensitivity: A/Div Peak : A Average : A peak to average: Time Sensitivity: 200 ms/div Time to peak: s

8 Output Page 5 of 6 Pages Lamp (rms):55.25v Lamp (rms):0.7164a Power:39.58W Ripple :0.016A Energy Efficiency:0.899 Lamp Wave Lamp Wave

9 Page 6 of 6 Pages Input & Output Characteristics Test Report Input Characteristics Test Report [Narrow Band] Output characteristics Start Phase: 14.1 Peak Phase: 63.3 End Phase: Vthd(IEC): 3.56% Athd(IEC):50.18% : (V) VCF: Vthd(IEC): 3.56% : 0.222(A) ACF: Athd(IEC): 50.18% Power: 44.1(W) Power Factor: Frequency: 49.97(Hz) Spectrum H3: 1.82% H5: 2.92% H7: 0.51% H9: 0.28% Spectrum H3: 18.69% H5: 19.07% H7: 14.84% H9: 20.67% Lamp (rms):55.25v Lamp (rms):0.7164a Power:39.58W Ripple :0.016A Energy Efficiency:0.899