TECHNICAL DATA PRELIMINARY BROCHURE MATERIAL HANDLER F-SERIES. mhl hp up to 70,107 lbs up to 44'11"

Transcription

1 TECHNICAL DATA PRELIMINARY BROCHURE MATERIAL HANDLER F-SERIES mhl 4 1 hp up to,1 lbs up to 44'11"

2 mhl4 F-Series TECHNICAL DATA OPERATING WEIGHT WITHOUT ATTACHMENTS MHL4 F MHL4 F FQC DIESEL ENGINE Manufacturer and model Confi guration Engine management system Type 28.5 t 2. t 28.5 t 4.6 t Deutz 6.1 L6 6-cylinder inline EMR IV Engine output power 129 kw Nominal speed 2 min -1 Displacement Cooling system Emission standard Air fi lter design Fuel tank DEF tank 4-stroke diesel, common rail direct injection, turbocharger, controlled exhaust gas recirculation, diesel particulate fi lter with automatic regeneration 6.1 l ELECTRICAL SYSTEM Generator Operating voltage Battery Lighting set Optional equipment TRAVEL DRIVE Combi-cooler (coolant/ charge air) with fan speed control system; optional reversing function Kat. IV/EPA Tier 4 fi nal Two-stage fi lter with safety cartridge and pre-separator with discharge valve 8 l (for at least two working shifts) 2 l Ad Blue 28 V / 1 A 24 V 2 12 V / 11 Ah / 5 A (in accordance with EN standards) 2 LED headlamps, turn indicators and tail lights 1 kw or 1 kw generator with controls and insulation monitoring, driven by V-belt direct from diesel engine Hydrostatic travel drive via infi nitely variable axial piston motor with directly mounted travel brake valve, two-speed manual gearshift, 4-wheel drive Maximum speed, 1st gear 5 km/h Maximum speed, 2nd gear 18 km/h Gradeability max. 4 % Turning radius 8.2 m SWING DRIVE Swing gear Drive Upper carriage swing speed Swing brake Max. swing torque Double row, internally geared ball-race slewing ring 2-stage planetary gear with integrated multi-disc brake Infi nitely variable from,5 rpm Electrically operated 66 knm UNDERCARRIAGE Front axle Rear axle Support Tires BRAKE SYSTEM Service brake Parking brake Rigid axle with integral drum brake, planetary drive, max. steering angle: 2 Oscillating axle with integral drum brake and selectable oscillation lock, planetary drive 4-point stabilizer system HYDRAULIC SYSTEM Solid rubber, 8-ply 1. 2 for MHL4F, for MHL4F FQC Hydraulic single-circuit braking system acting on all four wheel pairs Electrically operated disc brake on travel gearbox, acting on both front and rear axles LINDE mobile hydraulic system with load limit control and fuelsaving power demand control. Separate hydraulic oil cooler, temperature-controlled fan speed, with optional reversing function Hydraulic oil fi lter Max. pump fl ow Max. pressure Hydraulic oil tank OPERATOR CAB Cab Air-conditioning Operator s seat Monitoring Sound levels Integral return fi lter in oil tank for work hydraulics, with operating hrs service interval; oil fi ltration on all auxiliary circuits 2 l/min 2 / 6 bar 5 l usable tank capacity OFFICIAL APPROVALS Infi nitely variable hydraulic height-adjustment with eye level up to 5.6 m above ground. Flexibly mounted. Sound-insulated; heat-insulating glass panoramic windows for optimum all-around view; windshield with pull-down sunblind that slides under the cab roof; viewing window on cab roof; sliding window in cab door, sliding door. Automatic air-conditioning. Infi nitely variable heating with 8-speed fan, 1 adjustable air nozzles, defroster nozzles (hot water system). Air-cushioned high-comfort seat with integrated headrest, safety belt and lumbar support, seat heating with integrated a/c function optional. Seat position, seat inclination, seat cushion multi-adjustable relative to position of armrests and pilot control units, allowing comfortable operation. Ergonomic layout; glare-free instrumentation. Multifunction display, automatic monitoring and recording of abnormal operating conditions (including all hydraulic oil fi lters, hydraulic oil temperature (cold / hot) coolant temperature and charge air temperature condition of cooling system, diesel particulate fi lter load), visual and audible warning indication with shutdown of pilot control/ engine power reduction. Diagnosis of individual sensors available via the multi-function display. Rear view camera and side view camera. LW(A) = 11 db(a) (guaranteed) in accordance with directive 2/14 EC; max allowable under 2/14 EC = 14 db(a) Certifi ed in accordance with CE regulations 2

3 Technical data EQUIPMENT ENGINE Standard Option Charge air cooling Direct electronic fuel injection/common rail Automatic idle Engine preheating Engine diagnostics interface System-controlled fan drive with fan speed monitoring UNDERCARRIAGE All-wheel drive with differential Drum brakes Rear axle oscillating lock 2-speed powershift transmission 4-point stabilizers Stabilizer cylinders with integrated two-way check valves Piston rod protection on stabilizer cylinders Stabilizer plates 1'8" 2'2" 4-point stabilizers, individually controllable Tool box Special paint (customer paint work) UPPERCARRIAGE Separate cooling systems (combi-cooler for engine and hydraulic oil cooler) Cooling system fan speeds controlled by operating parameters Fan drive reversing function Lockable maintenance hatches, with gas struts Automatic central lubrication system Rear view camera Side view camera Travel alarm Electric refuelling pump Lighting protection Special paint (customer paint work) CAB Standard Option Hydraulically adjustable cab -layer glass with protection fi lm Sliding window in cab door Glazed roof panel Reinforced glass (windscreen and roof panel) Windshield washer system Roof washer system Air-cushioned operator seat with headrest, seatbelt, and lumbar support Seat heating with integrated A/C function Joystick steering Steering column, height and tilt adjustable Automatic air conditioning system Independent heating system Multi-function display Document clip Protective grilles to front and roof 12 V transformer Radio USB & Bluetooth 12 V socket Fire extinguisher, dry powder EQUIPMENT 1 kw DC generator with controls 1 kw DC generator with controls Close proximity range limiter for dipperstick Coolant and hydraulic oil level monitoring system Filter system for attachments Hose rupture valve for boom cylinder Hose rupture valve for stick cylinder Overload and work area control Overload warning device Quick coupling on dipperstick Dipperstick impact protection Active cyclone prefi lter (TOP AIR) Hydraulic oil preheating 2 V Float switch for barge unloading Lubrication of the grab suspension by central lubrication system Light packages LED LED front headlights Fuchs Telematics System Further optional equipment available on request!

4 mhl4 F-Series DIMENSIONS 8'1" 9'9" 9'" 1'" 1' 1'8" 4'5" 9' 1'11" 8'1" 5'1" 1' 8'9" 9' 1'2" 14'" 6'" 9'1" 4

5 Technical data TRANSPORT DIMENSIONS Loading system 44'11": undercarriage equipped with dozer blade, rotated by 18 6" C 1'11" 6'" 5'1" Average center of gravity in transport position B 4'" A Dimensions Reach 4' (multi-purpose stick) Reach 41'4" Reach 44'11" A 6'9" 6'1" 6'1" B 19'9" 19'1" 15'9" C 1'2" 1'8" 1'1" TRANSPORT DIMENSIONS MHL4 FQC 6" '2" 9'" 1'11" 6'1" 29'" 4'6" Average center of gravity in transport position 4'" 5

6 mhl4 F-Series WORKING RANGE 5 41'4" REACH WITH DIPPERSTICK 4 Loading equipment Boom 2'" 4 Dipperstick '8" 6 Multi-tine grapple.8 yd open RECOMMENDED ATTACHMENTS Open or half-closed 2 Fuchs multi-tine grapple.8 yd Open or half-closed 2 Fuchs multi-tine grapple 1.4 yd Open or half-closed Fuchs magnet plate MP 115 dia = 45" with 1.4 hp (1 kw) magnet system 1 Fuchs magnet plate MP 15 dia = 5" with 22.8 hp (1 kw) magnet system Clamshell grab 1. yd Density of materials handled up to 8.4 lbs/ft³ Clamshell grab 2.9 ft Density of materials handled up to lbs/ft³ Lift hook 22, lbs 1 Rotation center Fuchs multi-tine grapple.52 yd The lift capacity values are stated in imperial pounds (lbs). The pump pressure is 5,221 psi. In accordance with ISO 156 the lift capacity values represents 5% of the static tipping loads or 8% of the hydraulic lifting force (marked ). On solid and level ground the values apply to a swing range of 6. The ( ) values apply in the longitudinal direction of the undercarriage. The values for not supported only apply via the steering axle or the locked oscillating axle. The weights of the attached load hoisting equipment (grab, load hock, etc.) must be deducted from the lift capacity values. The working load of the lifting devise must be observed. In accordance with the EN 44-5 for object handling application hose rupture valves on the boom and stick cylinders, an overload warning device and the lift capacity table in the cab are required. For object handling application the machine has to be supported on a level ground Reach in ft LIFTING CAPACITY Height [ft] Undercarriage outrigger Reach [ft] ,9 (1,9 ) 11,8 (11,8 ) 5 19,44 (19,44 ),8 (,8 ) 11,9 (11,9 ) 19,4 (19,4 ),6 (,6 ) 12,69 (14,59 ) 9,66 (9,81 ) 25 19,95 (19,95 ),8 (,8 ) 12,6 (14,64 ) 9,1 (12,1) 2 21,1 (21,1 ),61 (1,48 ) 12,4 (14,9 ) 9,59 (11,88),65 (9,4 ) 15,9 (,9 ) 22,8 (22,8 ) 15,95 (18,28 ) 11,9 (14,9) 9,9 (11,6),58 (9,44) 1 4,61 (4,61 ) 21,49 (24,41 ) 15,2 (18,94 ) 11,54 (14,45) 9,15 (11,42),4 (9,2) 5 1,58 (1,58 ) 2,25 (24,82 ) 14,52 (18,48) 11,15 (14,4) 8,92 (11,18),5 (9,2) 11,6 (11,6 ) 19,48 (2,4 ) 14, (1,96 ) 1,85 (1,2 ) 8,5 (11,),28 (8,5 ) 5 19,1 (2,18 ) 1,8 (,14 ) 1,68 (12,86 ) 8,66 (9,9 ) 15,9 (15,9 ) Reach max. 41'11".2 6 6,2 (,49 )

7 Technical data WORKING RANGE 44'11" REACH WITH DIPPERSTICK Loading equipment Boom 2'" Dipperstick 2'4" Multi-tine grapple.8 yd open RECOMMENDED ATTACHMENTS Fuchs multi-tine grapple.52 yd Open or half-closed Fuchs multi-tine grapple.8 yd Open or half-closed Fuchs magnet plate MP 115 dia = '9" in with 1.4 hp (1 kw) magnet system Fuchs magnet plate MP 15 dia = 4'5" in with 22.8 hp (1 kw) magnet system Clamshell grab 5. ft Density of materials handled up to 8.4 lb/ft³ Lift hook 22, lbs The lift capacity values are stated in imperial pounds (lbs). The pump pressure is 5,221 psi. In accordance with ISO 156 the lift capacity values represents 5% of the static tipping loads or 8% of the hydraulic lifting force (marked ). On solid and level ground the values apply to a swing range of 6. The ( ) values apply in the longitudinal direction of the undercarriage. The values for not supported only apply via the steering axle or the locked oscillating axle. The weights of the attached load hoisting equipment (grab, load hock, etc.) must be deducted from the lift capacity values. The working load of the lifting devise must be observed. In accordance with the EN 44-5 for object handling application hose rupture valves on the boom and stick cylinders, an overload warning device and the lift capacity table in the cab are required. For object handling application the machine has to be supported on a level ground Reach in ft Rotation center LIFTING CAPACITY Height [ft] Undercarriage outrigger Reach [ft] ,8 (11,8 ) 4 11,8 (11,8 ),5 (,5 ) 5 14,14 (14,14 ) 11,61 (11,61 ) 6,9 (6,9 ) 15,1 (15,1 ) 1, (1,4 ) 9,91 (1,69 ) 25 15,4 (15,4 ) 12,9 (1,5 ) 9,88 (12, ),54 (8,9 ) 2 18,99 (18,99 ),8 (,8 ) 12,61 (1,92 ) 9,1 (12,2),69 (9,5) 15 2,82 (2,82 ),45 (1, ) 12,19 (14,4 ) 9, (11,6),55 (9,4) 5,6 (5,6 ) 1 1,5 (1,5 ) 22,4 (22,85 ) 15,59 (18, ) 11,69 (14,62 ) 9,15 (11,44),8 (9,25) 6, (6,82 ) 5,62 (4,56 ) 2,8 (24,2 ) 14, (18,6 ) 11,18 (14,9) 8,85 (11,12),2 (9,) 6, (,1 ),54 (,54 ) 19,59 (24,1 ) 14, (1,98) 1,5 (1,64) 8,59 (1,85),6 (8,91) 5,96 (6,14 ) 5 14,5 (14,5 ) 18,91 (22,2 ) 1,5 (1, ) 1,45 (1,) 8,4 (1,66) 6,9 (8,4 ) 1 18,6 (18,6 ) 1,6 (14,84 ) 1, (11,9 ) Reach max. 44'11".2 5,9 (5,9 )

8 mhl4 F-Series WORKING RANGE 4' REACH WITH MULTI-PURPOSE STICK Loading equipment Boom 2'" Multi-purpose stick 14'9" Sorting grapple The lift capacity values are stated in imperial pounds (lbs). The pump pressure is 5,221 psi. In accordance with ISO 156 the lift capacity values represents 5% of the static tipping loads or 8% of the hydraulic lifting force (marked ). On solid and level ground the values apply to a swing range of 6. The ( ) values apply in the longitudinal direction of the undercarriage. The values for not supported only apply via the steering axle or the locked oscillating axle. The weights of the attached load hoisting equipment (grab, load hock, etc.) must be deducted from the lift capacity values. The working load of the lifting devise must be observed. In accordance with the EN 44-5 for object handling application hose rupture valves on the boom and stick cylinders, an overload warning device and the lift capacity table in the cab are required. For object handling application the machine has to be supported on a level ground Reach in ft Rotation center LIFTING CAPACITY Height [ft] Undercarriage outrigger Reach [ft] ,28 (14,28 ) 5 18,6 (18,6 ) 14,8 (14,8 ) 19,81 (19,81 ), (,61 ) 11,91 (14,4 ) 25 2,29 (2,29 ),25 (,9 ) 11,85 (14,2 ) 8,98 (11,15 ) 2 2,12 (2,12 ) 21,42 (21,42 ) 15,6 (1,1 ) 11,6 (14,49 ) 8,9 (11,19) 15 1,85 (1,85 ) 21,9 (22,89 ) 15,8 (1,9 ) 11,2 (14,15) 8,1 (1,99) 6,9 (, ) 1 2,4 (2,6 ) 14,4 (18,2 ) 1,81 (1,2) 8,49 (1,6) 6,86 (8,1) 5 19,2 (2,6 ) 1, (1,65) 1,44 (1,) 8,29 (1,55) 6,8 (8,9) 8,94 (8,94 ) 18,59 (21, ) 1,28 (, ) 1,18 (1,5) 8,15 (1,21 ) 5 1,11 (14,9 ) 1, (11,8) Reach max. 4".2 6,61 (,1 ) 8

9 Technical data WORKING RANGE 6'1" REACH WITH DIPPERSTICK Loading equipment FQC Boom 1" Dipperstick 1'8" Multi-tine grapple.8 yd open with Fuchs QuickConnect (FQC) The lift capacity values are stated in imperial pounds (lbs). The pump pressure is 5,221 psi. In accordance with ISO 156 the lift capacity values represents 5% of the static tipping loads or 8% of the hydraulic lifting force (marked ). On solid and level ground the values apply to a swing range of 6. The ( ) values apply in the longitudinal direction of the undercarriage. The values for not supported only apply via the steering axle or the locked oscillating axle. The weights of the attached load hoisting equipment (grab, load hock, etc.) must be deducted from the lift capacity values. The working load of the lifting devise must be observed. In accordance with the EN 44-5 for object handling application hose rupture valves on the boom and stick cylinders, an overload warning device and the lift capacity table in the cab are required. For object handling application the machine has to be supported on a level ground Reach in ft Rotation center LIFTING CAPACITY Height [ft] Undercarriage outrigger Reach [ft] ,1 (11,1 ) 14,5 (14,5 ) 1,8 (1,8 ) 25 1,81 (1,81 ) 8,92 (8,92 ) 2 1,54 (1,54 ),6 (,6 ) 12,1 (12,1 ) 15 19,9 (19,9 ) 1,5 (1,5 ) 12, (14,2 ), (, ) 1 25,92 (25,92 ) 21,96 (21,96 ),41 (1,91 ) 12,9 (14,92 ) 9,1 (9,1 ) 5 56,2 (56,2 ),2 (,2 ) 22,5 (2,82 ) 15,6 (18,5 ) 11,68 (14,8 ) 9,15 (9,82 ),99 (,99 ) 4,2 (4,9 ) 21,25 (24,2 ) 14,96 (18,29 ) 11, (14, ) 8,61 (8,61 ) 5 15,6 (15,6 ) 1,59 (1,59 ) 2,49 (22,6 ) 14,55 (,52 ) 11,15 (11,92 ) Reach max. 6'1".5 5,11 (5,11 ) 9

10 mhl4 F-Series WORKING RANGE 6'8" REACH WITH MULTI-PURPOSE STICK Loading equipment FQC Boom 1" Multi-purpose stick 18'4" Sorting grapple with Fuchs QuickConnect (FQC) The lift capacity values are stated in imperial pounds (lbs). The pump pressure is 5,221 psi. In accordance with ISO 156 the lift capacity values represents 5% of the static tipping loads or 8% of the hydraulic lifting force (marked ). On solid and level ground the values apply to a swing range of 6. The ( ) values apply in the longitudinal direction of the undercarriage. The values for not supported only apply via the steering axle or the locked oscillating axle. The weights of the attached load hoisting equipment (grab, load hock, etc.) must be deducted from the lift capacity values. The working load of the lifting devise must be observed. In accordance with the EN 44-5 for object handling application hose rupture valves on the boom and stick cylinders, an overload warning device and the lift capacity table in the cab are required. For object handling application the machine has to be supported on a level ground Reach in ft 1 1 Rotation center LIFTING CAPACITY Height [ft] Undercarriage outrigger Reach [ft] ,1 (11,1 ) 1,5 (1,5 ) 25 1,6 (1,6 ) 8,8 (8,8 ) 2 15, (15, ) 11,6 (11,6 ) 4,42 (4,42 ) 15 18,44 (18,44 ),9 (,9 ) 12,12 (1,88 ),55 (,55 ) 1 22,48 (22,48 ) 2,82 (2,82 ),11 (,98 ) 11,1 (14,12 ) 8,91 (9,29 ) 5 5,6 (5,6 ) 1,82 (1,82 ) 22,28 (22,8 ) 15, (1,6 ) 11, (14,1 ) 8,69 (1,6 ) 1,94 (1,94 ),8 (,8 ) 2,86 (2,45 ) 14,5 (1,58 ) 1,8 (1,49 ) 8,5 (9,29 ) 5 14,99 (14,99 ) 1,2 (1,2 ) 19,9 (21,86 ) 14,5 (,4 ) 1,64 (11,59 ) Reach max. 6'8".5 4,24 (4,24 ) 1

11 Technical data WORKING RANGE WITH SCRAP SHEARS Loading equipment FQC Boom 1' Scrap shears GXP with Fuchs QuickConnect (FQC) Cutting force 549 kn Jaw depth 2' Jaw opening 1'1" Weight* 8,819 lbs The lift capacity values are stated in imperial pounds (lbs). The pump pressure is 5,221 psi. In accordance with ISO 156 the lift capacity values represents 5% of the static tipping loads or 8% of the hydraulic lifting force (marked ). On solid and level ground the values apply to a swing range of 6. The ( ) values apply in the longitudinal direction of the undercarriage. The values for not supported only apply via the steering axle or the locked oscillating axle. The weights of the attached load hoisting equipment (grab, load hock, etc.) must be deducted from the lift capacity values. The working load of the lifting devise must be observed. In accordance with the EN 44-5 for object handling application hose rupture valves on the boom and stick cylinders, an overload warning device and the lift capacity table in the cab are required. For object handling application the machine has to be supported on a level ground Reach in ft 1 1 Rotation center The unique FUCHS QuickConnect system Time is money and with the FUCHS QuickConnect (FQC) system, you can reduce attachment-change downtime to a fraction of the usual cost. For example, in less than a minute you can switch from a multi-purpose stick / grab combination to a dipperstick with a magnet or scrap shears. Using leak-free quick couplers, attachments can be changed quickly and safely from inside the cab. For the operator, climbing in and out and removing and replacing bolts are now just things of the past. 11

12 GET A HANDLE ON FLEET MANAGEMENT. Fuchs Telematics System: Recognize and Optimize Potential. The Fuchs Telematics system: know exactly how and where everything is running. The system offers a modern solution to help you analyze and optimize the effi ciency of your machines. It records and communicates valuable information on the operating status of each individual machine. Where are the machines? How are they working? Is a service check pending? Take advantage of this advanced software and get a handle on your fl eet management with the tool that connects for you. ALL-IN-ONE MACHINE MANAGEMENT. EVERYTHING AT A GLANCE: OPERATING DATA, MACHINE STATUS, GPS DATA Record, display, and analyse data: high effi ciency through precise information Available online anywhere and at any time*: comprehensive information on the GPS location, start and stop times, fuel consumption, operating hours, maintenance status, and much more. User-friendly interface: displays information clearly for at a glance metrics and diagnostics. Take action before damage occurs: predetermined maintenance intervals are signaled and error messages are displayed in plain text messages. The Fuchs Telematics system is optionally available or can be retrofi tted into existing machines to help control your operating costs and keep your machines in top shape. * Internet connection required May 21. Product specifi cations and prices are subject to change without notice or obligation. The photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator s Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or implied. Terex Corporation 21 Terex, the Terex Crown design, Fuchs and Works For You are trademarks of Terex Corporation or its subsidiaries.