DEFOGGER SECTION DEF CONTENTS DRIVER CONTROLS DEF-1 BASIC INSPECTION... 3 FUNCTION DIAGNOSIS... 6 ECU DIAGNOSIS...21 COMPONENT DIAGNOSIS...

Transcription

1 DRIVER CTROLS SECTI DEF A DEFOGGER B C D CTENTS E BASIC INSPECTI... 3 DIAGNOSIS AND REPAIR WORKFLOW... 3 Work Flow...3 FUNCTI DIAGNOSIS... 6 REAR WINDOW DEFOGGER SYSTEM... 6 System Diagram...6 System Description...6 Component Parts Location...7 Component Description...7 DIAGNOSIS SYSTEM (BCM)... 9 COMM ITEM...9 COMM ITEM : Diagnosis Description...9 COMM ITEM : CSULT-III Function...9 REAR WINDOW DEFOGGER...9 REAR WINDOW DEFOGGER : CSULT-III Function (BCM - REAR DEFOGGER)...10 CAN COMMUNICATI...11 System Description...11 COMPENT DIAGNOSIS...12 REAR WINDOW DEFOGGER SWITCH...12 Description...12 Component Function Check...12 Diagnosis Procedure...12 REAR WINDOW DEFOGGER RELAY...13 Description...13 Component Function Check...13 Diagnosis Procedure...13 Component Inspection...14 REAR WINDOW DEFOGGER POWER SUP- PLY AND GROUND CIRCUIT...15 Description...15 Component Function Check...15 Diagnosis Procedure...15 Component Inspection...16 DRIVER SIDE DOOR MIRROR DEFOGGER...17 Description...17 Component Function Check...17 Diagnosis Procedure...17 Component Inspection...18 PASSENGER SIDE DOOR MIRROR DEFOG- GER...19 Description...19 Component Function Check...19 Diagnosis Procedure...19 Component Inspection...20 ECU DIAGNOSIS Reference Value...21 Terminal Layout...26 Physical Values...26 Wiring Diagram...45 Fail Safe...53 DTC Inspection Priority Chart...55 DTC Index...56 SYMPTOM DIAGNOSIS...59 REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT OPERATE Diagnosis Procedure...59 REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR MIRROR DEFOGGER OPERATE Diagnosis Procedure...60 BOTH DOORS MIRROR DEFOGGER D T OPERATE BUT REAR WINDOW DEFOG- GER OPERATES...61 Diagnosis Procedure...61 F G H I J K DEF M N O P DEF-1

2 DRIVER SIDE DOOR MIRROR DEFOGGER DOES NOT OPERATE Diagnosis Procedure PASSENGER SIDE DOOR MIRROR DEFOG- GER DOES NOT OPERATE Diagnosis Procedure REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WINDOW DEFOG- GER OPERATES Diagnosis Procedure PRECAUTI PRECAUTIS Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIER" Precautions Necessary for Steering Wheel Rotation after Battery Disconnect VEHICLE REPAIR FILAMENT Inspection and Repair CDENSER Removal and Installation DEF-2

3 < BASIC INSPECTI > DIAGNOSIS AND REPAIR WORKFLOW BASIC INSPECTI DIAGNOSIS AND REPAIR WORKFLOW Work Flow OVERALL SEQUENCE INFOID: A B C D E F G H I J K DEF M N O P DETAILED FLOW DEF-3 JMKIA2270GB

4 DIAGNOSIS AND REPAIR WORKFLOW < BASIC INSPECTI > 1. GET INFORMATI FOR SYMPTOM Get the detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> GO TO 2 2. CHECK DTC 1. Check DTC. 2. Perform the following procedure if DTC is displayed. - Record DTC and freeze frame data (Print them out with CSULT-III.) - Erase DTC. - Study the relationship between the cause detected by DTC and the symptom described by the customer. 3. Check related service bulletins for information. Is any symptom described and any DTC detected? Symptom is described, DTC is displayed>>go TO 3 Symptom is described, DTC is not displayed>>go TO 4 Symptom is not described, DTC is displayed>>go TO 5 3. CFIRM THE SYMPTOM Confirm the symptom described by the customer. Connect CSULT-III to the vehicle in DATA MITOR mode and check real time diagnosis results. Verify relation between the symptom and the condition when the symptom is detected. >> GO TO 5 4. CFIRM THE SYMPTOM Confirm the symptom described by the customer. Connect CSULT-III to the vehicle in DATA MITOR mode and check real time diagnosis results. Verify relation between the symptom and the condition when the symptom is detected. >> GO TO 6 5. PERFORM DTC CFIRMATI PROCEDURE Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again. At this time, always connect CSULT-III to the vehicle, and check diagnostic results in real time. If two or more DTCs are detected, refer to BCS-81, "DTC Inspection Priority Chart" and determine trouble diagnosis order. NOTE: Freeze frame data is useful if the DTC is not detected. Perform Component Function Check if DTC Confirmation Procedure is not included in Service Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during this check. If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation Procedure. Is DTC detected? YES >> GO TO 7 NO >> Refer to GI-39, "Intermittent Incident". 6. DETECT MALFUNCTIING SYSTEM BY SYMPTOM TABLE Detect malfunctioning system according to DEF-6, "System Description" based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom. >> GO TO 7 7. DETECT MALFUNCTIING PART BY DIAGNOSTIC PROCEDURE Inspect according to Diagnostic Procedure of the system. NOTE: DEF-4

5 < BASIC INSPECTI > DIAGNOSIS AND REPAIR WORKFLOW The Diagnostic Procedure described is based on open circuit inspection. A short circuit inspection is also required for the circuit check in the Diagnostic Procedure. Is malfunctioning part detected? YES >> GO TO 8 NO >> Check voltage of related BCM terminals using CSULT-III. 8. REPAIR OR REPLACE THE MALFUNCTIING PART 1. Repair or replace the malfunctioning part. 2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replacement. 3. Check DTC. If DTC is displayed, erase it. >> GO TO 9 9. FINAL CHECK When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check again, and then check that the malfunction has been repaired securely. When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that the symptom is not detected. Does the symptom reappear? YES (DTC is detected)>>go TO 7 YES (Symptom remains)>>go TO 6 NO >> Inspection End. A B C D E F G H I J K DEF M N O P DEF-5

6 REAR WINDOW DEFOGGER SYSTEM < FUNCTI DIAGNOSIS > FUNCTI DIAGNOSIS REAR WINDOW DEFOGGER SYSTEM System Diagram INFOID: System Description ALLIA0912GB INFOID: Operation Description Turn rear window defogger switch when the ignition switch is turned. Then front air control (rear window defogger switch) transmits rear window defogger switch signal to BCM. BCM turns rear window defogger relay when rear window defogger switch signal is received. Rear window defogger and door mirror defogger (with door mirror defogger) are supplied with power and operate when rear window defogger relay turns. BCM transmits rear window defogger control signal to IPDM E/R via CAN communication when rear window defogger operates. Rear window defogger is displayed when controller (auto amp.) receives signals. Timer function BCM turns rear window defogger relay for approximately 15 minutes when rear window defogger switch is turned while ignition switch is. It makes rear window defogger and door mirror defogger (with door mirror defogger) operate. Timer is canceled after pressing rear window defogger switch again during timer operation. Then BCM turns rear window defogger relay. The same reaction also occurs during timer operation, if the ignition switch is turned. INPUT/OUTPUT SIGNAL CHART Switch Input signal to BCM BCM function Actuator Rear window defogger switch Defogger switch signal Rear window defogger and door Push button ignition switch Ignition signal mirror defogger * control *: With door mirror defogger Rear window defogger Door mirror defogger * DEF-6

7 < FUNCTI DIAGNOSIS > Component Parts Location REAR WINDOW DEFOGGER SYSTEM INFOID: A B C D E F G H I J K 1. BCM M16, M17, M18, M19 (view with instrument panel removed) 4. A/C auto amp. (rear window defogger switch) M37 7. Rear window defogger (-) B54 (view with rear pillar finisher RH removed) Component Description ALLIA0911ZZ 2. IPDM E/R E17 3. A. Fuse block (J/B) B. Rear window defogger relay 5. Door mirror (door mirror defogger) LH D4, RH D107 (if equipped) 6. A. Rear window defogger (+) B53 B. Condenser B52 (view with rear pillar finisher LH removed) INFOID: DEF M N BCM Rear window defogger relay A/C auto amp. (rear window defogger switch) Operates the rear window defogger with the operation of rear window defogger switch. Performs the timer control of rear window defogger. Operates the rear window defogger and the door mirror defogger with the control signal from BCM. The rear window defogger switch is turned. Turns the indicator lamp when detecting the operation of rear window defogger. O P DEF-7

8 REAR WINDOW DEFOGGER SYSTEM < FUNCTI DIAGNOSIS > Rear window defogger Door mirror defogger * Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window from fogging up. Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror from fogging up. *: With heated mirrors DEF-8

9 < FUNCTI DIAGNOSIS > DIAGNOSIS SYSTEM (BCM) COMM ITEM COMM ITEM : Diagnosis Description DIAGNOSIS SYSTEM (BCM) BCM CSULT-III FUNCTI CSULT-III performs the following functions via CAN communication with BCM. Diagnosis mode WORK SUPPORT SELF-DIAG RESULTS CAN DIAG SUPPORT MNTR DATA MITOR ACTIVE TEST ECU IDENTIFICATI CFIGURATI Function Description Changes the setting for each system function. Displays the diagnosis results judged by BCM. Monitors the reception status of CAN communication viewed from BCM. The BCM input/output signals are displayed. The signals used to activate each device are forcibly supplied from BCM. The BCM part number is displayed. This function is not used even though it is displayed. INFOID: A B C D E F SYSTEM APPLICATI BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the following for all sub system selection items. Diagnosis mode System Sub system selection item WORK SUPPORT DATA MITOR ACTIVE TEST Door lock DOOR LOCK Rear window defogger REAR DEFOGGER Warning chime BUZZER Interior room lamp timer INT LAMP Exterior lamp HEADLAMP Wiper and washer WIPER Turn signal and hazard warning lamps FLASHER Air conditioner AIR CDITER Intelligent Key system INTELLIGENT KEY Combination switch COMB SW BCM BCM Immobilizer IMMU Interior room lamp battery saver BATTERY SAVER Trunk open TRUNK Vehicle security system THEFT ALM RAP system RETAINED PWR Signal buffer system SIGNAL BUFFER TPMS AIR PRESSURE MITOR COMM ITEM : CSULT-III Function INFOID: G H I J K DEF M N O P ECU IDENTIFICATI Displays the BCM part No. SELF-DIAG RESULT Refer to BCS-82, "DTC Index". REAR WINDOW DEFOGGER DEF-9

10 < FUNCTI DIAGNOSIS > DIAGNOSIS SYSTEM (BCM) REAR WINDOW DEFOGGER : CSULT-III Function (BCM - REAR DEFOGGER) DATA MITOR INFOID: Monitor Item [Unit] PUSH SW [/] REAR DEF SW [/] Description Indicates condition of push switch Displays Press ()/other () status determined with the rear window defogger switch ACTIVE TEST Test Item REAR DEFOGGER Description This test is able to check rear window defogger operation. Rear window defogger operates when " on CSULT-III screen is touched DEF-10

11 < FUNCTI DIAGNOSIS > CAN COMMUNICATI System Description CAN COMMUNICATI INFOID: A Refer to LAN-6, "System Description". B C D E F G H I J K DEF M N O P DEF-11

12 REAR WINDOW DEFOGGER SWITCH < COMPENT DIAGNOSIS > COMPENT DIAGNOSIS REAR WINDOW DEFOGGER SWITCH Description INFOID: The rear window defogger is operated by turning the rear window defogger switch. Turns the indicator lamp in the rear window defogger switch when operating the rear window defogger. Component Function Check INFOID: CHECK REAR WINDOW DEFOGGER SWITCH FUNCTI Check that the indicator lamp of rear window defogger illuminates with rear window defogger switch. YES >> Rear window defogger switch function is OK. NO >> Refer to DEF-12, "Diagnosis Procedure". Diagnosis Procedure 1. CHECK A/C AUTO AMP. (REAR WINDOW DEFOGGER SWITCH) Does A/C auto amp. operate normally? YES >> Inspection End. NO >> GO TO 2 2. CHECK REAR WINDOW DEFOGGER SWITCH INDICATOR CIRCUIT 1. Turn ignition switch. 2. Check voltage between A/C auto amp. connector and ground. INFOID: (+) A/C auto amp. connector Terminals Terminal ( ) M37 26 Condition of rear window defogger switch Voltage (V) (Approx.) Battery voltage 0 YES >> Replace A/C auto amp. Refer to VTL-18, "FAN C- TROL AMP. : Removal and Installation". NO >> Repair or replace harness. ALLIA0915ZZ DEF-12

13 < COMPENT DIAGNOSIS > REAR WINDOW DEFOGGER RELAY REAR WINDOW DEFOGGER RELAY Description Power is supplied to the rear window defogger with BCM control. Component Function Check INFOID: INFOID: A B 1. CHECK REAR WINDOW DEFOGGER RELAY POWER SUPPLY CIRCUIT Check that an operation noise of rear window defogger relay [located in fuse block (J/B)] can be heard when turning the rear window defogger switch. YES >> Rear window defogger relay power supply circuit is OK. NO >> Refer to DEF-13, "Diagnosis Procedure". Diagnosis Procedure INFOID: C D E 1. CHECK REAR WINDOW DEFOGGER RELAY GROUND CIRCUIT 1. Turn ignition switch. 2. Check voltage between BCM connector and ground. (+) BCM connector Terminals Terminal Condition of rear window defogger switch YES >> Rear window defogger relay power supply circuit is OK. NO >> GO TO 2 2. CHECK HARNESS CTINUITY 1. Turn ignition switch. 2. Disconnect BCM and fuse block (J/B). 3. Check continuity between BCM connector (A) and fuse block (J/ B) connector (B). 4. Check continuity between BCM connector (A) and ground. YES >> GO TO 3 NO >> Repair or replace harness. 3. CHECK REAR WINDOW DEFOGGER RELAY Check rear window defogger relay. Refer to DEF-14, "Component Inspection". YES >> GO TO 4 NO >> Replace rear window defogger relay. ( ) M18 59 Voltage (V) (Approx.) 0 Battery voltage BCM connector Terminal Fuse block (J/B) connector Terminal Continuity M18 (A) 59 M4 (B) 4Q Yes BCM connector Terminal Continuity M18 (A) 59 No ALLIA0175ZZ ALLIA0916ZZ F G H I J K DEF M N O P DEF-13

14 REAR WINDOW DEFOGGER RELAY < COMPENT DIAGNOSIS > 4. CHECK INTERMITTENT INCIDENT Check intermittent incident. Refer to GI-39, "Intermittent Incident". YES >> Check the following. Battery power supply circuit. Fuse block (J/B). NO >> Repair or replace the malfunctioning parts. Component Inspection INFOID: CHECK REAR WINDOW DEFOGGER RELAY Check rear window defogger relay. Terminal Rear window defogger relay 3 5 Condition 12V direct current supply between terminals 1 and 2. No current supply YES >> Inspection End. NO >> Replace rear window defogger relay. Continuity Yes No SEF497Y DEF-14

15 REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT < COMPENT DIAGNOSIS > REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT Description INFOID: Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window from fogging up. Component Function Check INFOID: CHECK REAR WINDOW DEFOGGER Check that the heating wire of rear window defogger is heated when turning the rear window defogger switch. YES >> Rear window defogger is OK. NO >> Refer to DEF-15, "Diagnosis Procedure". Diagnosis Procedure 1. CHECK POWER SUPPLY CIRCUIT 1. Turn ignition switch. 2. Check voltage between rear window defogger connector and ground. Rear window defogger connector (+) Terminals Terminal ( ) B53 1 Condition of rear window defogger switch Voltage (V) (Approx.) YES >> GO TO 2 NO >> GO TO 3 2. CHECK GROUND CIRCUIT 1. Turn ignition switch. 2. Disconnect rear window defogger. 3. Check continuity between rear window defogger connector and ground. INFOID: Battery voltage 0 ALLIA0177ZZ A B C D E F G H I J K DEF M Rear window defogger connector Terminal Continuity B54 2 Yes YES >> GO TO 5 NO >> Repair or replace harness. N O 3. CHECK HARNESS CTINUITY 1 1. Turn ignition switch. 2. Disconnect condenser and rear window defogger. ALLIA0178ZZ P DEF-15

16 REAR WINDOW DEFOGGER POWER SUPPLY AND GROUND CIRCUIT < COMPENT DIAGNOSIS > 3. Check continuity between condenser connector (A) and rear window defogger connector (B). Condenser connector Terminal Rear window defogger connector Terminal Continuity B52 (A) 1 B53 (B) 1 Yes YES >> GO TO 4 NO >> Replace condenser. Refer to DEF-68, "Removal and Installation". 4. CHECK HARNESS CTINUITY 2 1. Disconnect fuse block (J/B). 2. Check continuity between fuse block (J/B) connector (A) and condenser connector (B). ALLIA0179ZZ Fuse block (J/B) connector B4 (A) Terminal 10T 11T YES >> GO TO 6 NO >> Replace or repair harness. 5. CHECK FILAMENT Check filament. Refer to DEF-16, "Component Inspection". YES >> Refer to GI-39, "Intermittent Incident". NO >> Repair filament. Refer to DEF-66, "Inspection and Repair". 6. CHECK INTERMITTENT INCIDENT Check intermittent incident. Refer to GI-39, "Intermittent Incident". YES >> Check the following. Battery power supply circuit. Fuse block (J/B). NO >> Repair or replace the malfunctioning parts. Component Inspection Condenser connector Terminal Continuity B52 (B) 1 Yes ALLIA0180ZZ INFOID: CHECK FILAMENT Check the filament for damage or open circuits. Refer to DEF-66, "Inspection and Repair". YES >> Inspection End. NO >> Repair filament. Refer to DEF-66, "Inspection and Repair". DEF-16

17 < COMPENT DIAGNOSIS > DRIVER SIDE DOOR MIRROR DEFOGGER DRIVER SIDE DOOR MIRROR DEFOGGER Description INFOID: A Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror from fogging up. Component Function Check INFOID: CHECK DOOR MIRROR DEFOGGER LH Check that heating wire of door mirror defogger LH is heated when turning the rear window defogger switch. YES >> Door mirror defogger is OK. NO >> Refer to DEF-17, "Diagnosis Procedure". Diagnosis Procedure 1. CHECK POWER SUPPLY CIRCUIT 1. Turn ignition switch. 2. Disconnect door mirror LH. 3. Turn ignition switch. 4. Check voltage between door mirror LH connector and ground. INFOID: B C D E F G (+) Door mirror LH connector Terminals Terminal ( ) D4 5 Condition of rear window defogger switch Voltage (V) (Approx.) Battery voltage 0 YES >> GO TO 2 NO >> Repair or replace harness. 2. CHECK GROUND CIRCUIT 1. Turn ignition switch. 2. Check continuity between door mirror LH connector and ground. ALLIA0917ZZ H I J K DEF Door mirror LH connector Terminal Continuity D4 13 Yes YES >> GO TO 3 NO >> Repair or replace harness. 3. CHECK DOOR MIRROR DEFOGGER LH Check door mirror defogger LH. Refer to DEF-18, "Component Inspection". YES >> GO TO 4 NO >> Replace door mirror. Refer to MIR-19, "Removal and Installation". 4. CHECK INTERMITTENT INCIDENT ALLIA0918ZZ M N O P DEF-17

18 DRIVER SIDE DOOR MIRROR DEFOGGER < COMPENT DIAGNOSIS > Check intermittent incident. Refer to GI-39, "Intermittent Incident". YES >> Check the following. Battery power supply circuit. Fuse block (J/B). NO >> Repair or replace the malfunctioning parts. Component Inspection INFOID: CHECK DOOR MIRROR DEFOGGER LH 1. Turn ignition switch. 2. Disconnect door mirror LH. 3. Check continuity between door mirror terminals. Terminal Continuity 5 13 Yes YES >> Inspection End. NO >> Replace door mirror LH. Refer to MIR-19, "Removal and Installation". ALLIA0919ZZ DEF-18

19 < COMPENT DIAGNOSIS > PASSENGER SIDE DOOR MIRROR DEFOGGER PASSENGER SIDE DOOR MIRROR DEFOGGER Description INFOID: A Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror from fogging up. Component Function Check INFOID: CHECK DOOR MIRROR DEFOGGER RH Check that the heating wire of door mirror defogger RH is heated when turning the rear window defogger switch. YES >> Door mirror defogger RH is OK. NO >> Refer to DEF-19, "Diagnosis Procedure". Diagnosis Procedure 1. CHECK POWER SUPPLY CIRCUIT 1. Turn ignition switch. 2. Disconnect door mirror RH. 3. Turn ignition switch. 4. Check voltage between door mirror RH connector and ground. INFOID: B C D E F G (+) Door mirror RH connector Terminals Terminal ( ) D107 5 YES >> GO TO 2 NO >> Repair or replace harness. 2. CHECK GROUND CIRCUIT 1. Turn ignition switch. 2. Check continuity between door mirror RH connector and ground. YES >> GO TO 3 NO >> Repair or replace harness. Condition of rear window defogger switch Voltage (V) (Approx.) Battery voltage 0 Door mirror RH connector Terminal Continuity D Yes 3. CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER Check door mirror defogger RH. Refer to DEF-20, "Component Inspection". YES >> GO TO 4 NO >> Replace door mirror RH. Refer to MIR-19, "Removal and Installation". 4. CHECK INTERMITTENT INCIDENT ALLIA0917ZZ ALLIA0918ZZ H I J K DEF M N O P DEF-19

20 PASSENGER SIDE DOOR MIRROR DEFOGGER < COMPENT DIAGNOSIS > Check intermittent incident. Refer to GI-39, "Intermittent Incident". YES >> Check the following. Battery power supply circuit. Fuse block (J/B). NO >> Repair or replace the malfunctioning parts. Component Inspection INFOID: CHECK DOOR MIRROR DEFOGGER RH 1. Turn ignition switch. 2. Disconnect door mirror RH. 3. Check continuity between door mirror terminals. Terminal Continuity 5 13 Yes YES >> Inspection End. NO >> Replace door mirror RH. Refer to MIR-19, "Removal and Installation". ALLIA0919ZZ DEF-20

21 ECU DIAGNOSIS Reference Value INFOID: A B VALUES THE DIAGNOSIS TOOL Monitor Item Condition Value/Status FR WIPER HI Other than front wiper switch HI Front wiper switch HI FR WIPER LOW Other than front wiper switch LO Front wiper switch LO FR WASHER SW Front washer switch Front washer switch FR WIPER INT Other than front wiper switch INT Front wiper switch INT FR WIPER STOP Front wiper is not in STOP position Front wiper is in STOP position INT VOLUME Wiper intermittent dial is in a dial position 1-7 Wiper intermittent dial position TURN SIGNAL R TURN SIGNAL L TAIL LAMP SW HI BEAM SW HEAD LAMP SW 1 HEAD LAMP SW 2 PASSING SW AUTO LIGHT SW FR FOG SW DOOR SW-DR DOOR SW-AS DOOR SW-RR DOOR SW-RL Other than turn signal switch RH Turn signal switch RH Other than turn signal switch LH Turn signal switch LH Other than lighting switch 1ST and 2ND Lighting switch 1ST or 2ND Other than lighting switch HI Lighting switch HI Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch PASS Lighting switch PASS Other than lighting switch AUTO Lighting switch AUTO Front fog lamp switch Front fog lamp switch Driver door closed Driver door opened Passenger door closed Passenger door opened Rear door RH closed Rear door RH opened Rear door LH closed Rear door LH opened C D E F G H I J K DEF M N O P DEF-21

22 Monitor Item Condition Value/Status DOOR SW-BK CDL LOCK SW CDL UNLOCK SW KEY CYL LK-SW KEY CYL UN-SW KEY CYL SW-TR NOTE: This item is displayed, but cannot be monitored. Other than power door lock switch LOCK Power door lock switch LOCK Other than power door lock switch UNLOCK Power door lock switch UNLOCK Other than driver door key cylinder LOCK position Driver door key cylinder LOCK position Other than driver door key cylinder UNLOCK position Driver door key cylinder UNLOCK position NOTE: This item is displayed, but cannot be monitored. When hazard switch is not pressed HAZARD SW When hazard switch is pressed REAR DEF SW When rear window defogger switch is pressed TR CANCEL SW TR/BD OPEN SW TRNK/HAT MNTR RKE-LOCK RKE-UNLOCK RKE-TR/BD RKE-PANIC RKE-P/W OPEN RKE-MODE CHG OPTICAL SENSOR REQ SW-DR REQ SW-AS REQ SW-RL REQ SW-RR Trunk lid opener cancel switch Trunk lid opener cancel switch Trunk lid opener switch While the trunk lid opener switch is turned Trunk lid closed Trunk lid opened When LOCK button of Intelligent Key is not pressed When LOCK button of Intelligent Key is pressed When UNLOCK button of Intelligent Key is not pressed When UNLOCK button of Intelligent Key is pressed When TRUNK OPEN button of Intelligent Key is not pressed When TRUNK OPEN button of Intelligent Key is pressed When PANIC button of Intelligent Key is not pressed When PANIC button of Intelligent Key is pressed When UNLOCK button of Intelligent Key is not pressed and held When UNLOCK button of Intelligent Key is pressed and held When LOCK/UNLOCK button of Intelligent Key is not pressed and held simultaneously When LOCK/UNLOCK button of Intelligent Key is pressed and held simultaneously When outside of the vehicle is bright When outside of the vehicle is dark When front door request switch is not pressed (driver side) When front door request switch is pressed (driver side) When front door request switch is not pressed (passenger side) When front door request switch is pressed (passenger side) When rear door request switch is not pressed (driver side) When rear door request switch is pressed (driver side) When rear door request switch is not pressed (passenger side) When rear door request switch is pressed (passenger side) Close to 5 V Close to 0 V DEF-22

23 REQ SW-BD/TR PUSH SW IGN RLY 2-F/B ACC RLY-F/B CLUTCH SW BRAKE SW 1 DETE/CANCL SW SFT PN/N SW S/L-LOCK Monitor Item Condition Value/Status S/L-UNLOCK S/L RELAY-F/B UNLK SEN-DR PUSH SW-IPDM IGN RLY1 F/B DETE SW -IPDM SFT PN -IPDM SFT P-MET SFT N-MET ENGINE STATE S/L LOCK-IPDM S/L UNLCK-IPDM When trunk request switch is not pressed When trunk request switch is pressed When engine switch (push switch) is not pressed When engine switch (push switch) is pressed Ignition switch or ACC Ignition switch Ignition switch Ignition switch ACC or NOTE: This item is displayed, but cannot be monitored. When the brake pedal is not depressed When the brake pedal is depressed When selector lever is in P position When selector lever is in any position other than P When selector lever is in any position other than P or N When selector lever is in P or N position Electronic steering column lock LOCK status Electronic steering column lock UNLOCK status Electronic steering column lock UNLOCK status Electronic steering column lock LOCK status Ignition switch or ACC Ignition switch Driver door UNLOCK status Driver door LOCK status When engine switch (push switch) is not pressed When engine switch (push switch) is pressed Ignition switch or ACC Ignition switch When selector lever is in P position When selector lever is in any position other than P When selector lever is in any position other than P or N When selector lever is in P or N position When selector lever is in any position other than P When selector lever is in P position When selector lever is in any position other than N When selector lever is in N position Engine stopped While the engine stalls At engine cranking Engine running Electronic steering column lock LOCK status Electronic steering column lock UNLOCK status Electronic steering column lock UNLOCK status Electronic steering column lock LOCK status STOP STALL CRANK RUN A B C D E F G H I J K DEF M N O P DEF-23

24 S/L RELAY-REQ Ignition switch or ACC Ignition switch VEH SPEED 1 While driving Equivalent to speedometer reading VEH SPEED 2 While driving Equivalent to speedometer reading DOOR STAT-DR DOOR STAT-AS ID OK FLAG PRMT ENG STAT PRMT RKE STAT Driver door LOCK status Wait with selective UNLOCK operation (5 seconds) Driver door UNLOCK status Passenger door LOCK status Wait with selective UNLOCK operation (5 seconds) Passenger door UNLOCK status Ignition switch ACC or Ignition switch When the engine start is prohibited When the engine start is permitted NOTE: This item is displayed, but cannot be monitored. LOCK READY UNLK LOCK READY UNLK RESET SET RESET SET RESET When Intelligent Key is not inserted into key slot KEY SW -SLOT When Intelligent Key is inserted into key slot RKE OPE COUN1 During the operation of Intelligent Key Operation frequency of Intelligent Key RKE OPE COUN2 CFRM ID ALL CFIRM ID4 CFIRM ID3 CFIRM ID2 CFIRM ID1 TP 4 TP 3 TP 2 Monitor Item Condition Value/Status NOTE: This item is displayed, but cannot be monitored. The key ID that the key slot receives does not accord with any key ID registered to BCM. The key ID that the key slot receives accords with any key ID registered to BCM. The key ID that the key slot receives does not accord with the fourth key ID registered to BCM. The key ID that the key slot receives accords with the fourth key ID registered to BCM. The key ID that the key slot receives does not accord with the third key ID registered to BCM. The key ID that the key slot receives accords with the third key ID registered to BCM. The key ID that the key slot receives does not accord with the second key ID registered to BCM. The key ID that the key slot receives accords with the second key ID registered to BCM. The key ID that the key slot receives does not accord with the first key ID registered to BCM. The key ID that the key slot receives accords with the first key ID registered to BCM. The ID of fourth key is not registered to BCM The ID of fourth key is registered to BCM The ID of third key is not registered to BCM The ID of third key is registered to BCM The ID of second key is not registered to BCM The ID of second key is registered to BCM Operation frequency of Intelligent Key YET DE YET DE YET DE YET DE YET DE YET DE YET DE YET DE DEF-24

25 TP 1 AIR PRESS FL AIR PRESS FR AIR PRESS RR AIR PRESS RL ID REGST FL1 ID REGST FR1 ID REGST RR1 ID REGST RL1 WARNING LAMP BUZZER Monitor Item Condition Value/Status The ID of first key is not registered to BCM The ID of first key is registered to BCM Ignition switch (only when the signal from the transmitter is received) Ignition switch (only when the signal from the transmitter is received) Ignition switch (only when the signal from the transmitter is received) Ignition switch (only when the signal from the transmitter is received) When ID of front LH tire transmitter is registered When ID of front LH tire transmitter is not registered When ID of front RH tire transmitter is registered When ID of front RH tire transmitter is not registered When ID of rear RH tire transmitter is registered When ID of rear RH tire transmitter is not registered When ID of rear LH tire transmitter is registered When ID of rear LH tire transmitter is not registered Tire pressure indicator Tire pressure indicator Tire pressure warning alarm is not sounding Tire pressure warning alarm is sounding YET DE Air pressure of front LH tire Air pressure of front RH tire Air pressure of rear RH tire Air pressure of rear LH tire DE YET DE YET DE YET DE YET A B C D E F G H I J K DEF M N O P DEF-25

26 Terminal Layout INFOID: Physical Values ALMIA0127ZZ INFOID: DEF-26

27 Terminal No. (Wire color) Description Input/ Condition Signal name (+) (-) 1 Battery power supply Input Ignition switch Battery voltage (W/B) 2 (R/Y) 3 (L/W) 4 (P/W) 5 (G) 7 (R/W) 8 (V) 9 (L) 10 (G) 11 (Y/R) 13 (B) 14 (GR/ W) Battery power supply output Ignition power supply output Interior room lamp power supply Front door RH UN- LOCK Ignition switch Battery voltage Ignition switch Battery voltage After passing the interior room lamp battery saver operation time Any other time after passing the interior room lamp battery saver operation time Front door RH Step lamp Step lamp All doors LOCK All doors Front door LH UN- LOCK Rear door RH and rear door LH UN- LOCK Front door LH Rear door RH and rear door LH UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) LOCK (actuator is activated) Other than LOCK (actuator is not activated) UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) Battery voltage Battery voltage Battery voltage Battery voltage Battery voltage Battery voltage Battery power supply Input Ignition switch Battery voltage Ignition switch Engine switch (push switch) illumination ground Input Tail lamp Value (Approx.) NOTE: When the illumination brightening/dimming level is in the neutral position A B C D E F G H I J K DEF M N O 15 (Y/L) ACC indicator lamp Ignition switch ACC or Battery voltage JSNIA0010GB P DEF-27

28 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) Turn signal switch 17 (G/B) Turn signal (RH) Ignition switch Turn signal switch RH 6.5 V PKID0926E Turn signal switch 18 (G/Y) Turn signal (LH) Ignition switch Turn signal switch LH 19 (Y) 21 (P/B) 24 (R/W) 26 (O/L) Room lamp timer control Optical sensor signal Input Interior room lamp Ignition switch When outside of the vehicle is bright When outside of the vehicle is dark Battery voltage Close to 5V Close to Stop lamp switch 1 Input Battery voltage Stop lamp switch 2 Input Stop lamp switch (brake pedal is not depressed) (brake pedal is depressed) Battery voltage 6.5 V PKID0926E 27 (O) Front door lock assembly LH (unlock sensor) Input Front door LH LOCK status 29 (Y) 30 (V/Y) 31 (G) Key slot switch Input ACC feedback signal Input Ignition switch Rear window defogger feedback signal Input UNLOCK status When Intelligent Key is inserted into key slot When Intelligent Key is not inserted into key slot Rear window defogger switch Battery voltage 0 ACC or Battery voltage Battery voltage 11.8V JPMIA0011GB DEF-28

29 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A B 32 (R/B) Front door RH switch Input Front door RH switch (when front door RH closes) C 11.8 V JPMIA0011GB D (when front door RH opens) E 37 (O) Trunk lid opener cancel switch Input Trunk lid opener cancel switch CANCEL F 1.1V JPMIA0012GB G 38 (GR/ W) Rear window defogger signal Input Rear window defogger switch 5V H I 40 (Y/G) Power window serial link Input/ Ignition switch J 10.2V JPMIA0013GB K 41 (W) 42 (R) 45 (P) Engine switch (push switch) illumination LOCK indicator lamp Receiver & sensor ground Ignition switch or ACC Engine switch (push switch) illumination LOCK indicator lamp 5.5V Input Ignition switch Battery voltage DEF M N 46 (V/W) Receiver & sensor power supply output Ignition switch ACC or 5. O P DEF-29

30 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) Standby state OCC3881D 47 (G/O) Tire pressure receiver signal Input/ Ignition switch When receiving the signal from the transmitter OCC3880D 48 (R/G) Selector lever P/N position signal Input Selector lever P or N position 12. Except P and N positions 49 (L/O) Security indicator signal Security indicator Blinking 11.3V JPMIA0014GB Battery voltage All switch Lighting switch 1ST 50 (LG/ B) Combination switch OUTPUT 5 Combination switch (Wiper intermittent dial 4) Lighting switch high-beam Lighting switch 2ND Turn signal switch RH 10.7V JPMIA0031GB All switch (Wiper intermittent dial 4) Front wiper switch HI (Wiper intermittent dial 4) 51 (L/W) Combination switch OUTPUT 1 Combination switch Any of the conditions below with all switch Wiper intermittent dial 1 WIper intermittent dial 2 Wiper intermittent dial 3 Wiper intermittent dial 6 Wiper intermittent dial V JPMIA0032GB DEF-30

31 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A All switch (Wiper intermittent dial 4) B 52 (G/B) Combination switch OUTPUT 2 Combination switch Front washer switch (Wiper intermittent dial 4) Any of the conditions below with all switch Wiper intermittent dial 1 WIper intermittent dial 5 Wiper intermittent dial 6 All switch 10.7V JPMIA0033GB C D E Front wiper switch INT 53 (LG/ R) Combination switch OUTPUT 3 Combination switch (Wiper intermittent dial 4) Front wiper switch LO Lighting switch AUTO F G All switch 10.7V JPMIA0034GB H Front fog lamp switch 54 (G/Y) Combination switch OUTPUT 4 Combination switch (Wiper intermittent dial 4) Lighting switch 2ND Lighting switch flash-topass I J 57 (W) Tire pressure warning check switch Turn signal switch LH Input 5V 10.7V JPMIA0035GB K DEF 58 (SB) Front door LH switch Input Front door LH switch (front door LH CLOSE) M 11.8V JPMIA0011GB N (front door LH OPEN) 59 (G/R) Rear window defogger relay Rear window defogger Active Not activated Battery voltage O P DEF-31

32 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) When Intelligent Key is in the passenger compartment JMKIA0062GB 60 (B/R) Front console antenna 2 (-) Ignition switch When Intelligent Key is not in the passenger compartment JMKIA0063GB When Intelligent Key is in the passenger compartment JMKIA0062GB 61 (W/R) Center console antenna 2 (+) Ignition switch When Intelligent Key is not in the passenger compartment JMKIA0063GB When Intelligent Key is in the antenna detection area 62 (V) Front outside handle RH antenna (-) When the front door RH request switch is operated with ignition switch JMKIA0062GB When Intelligent Key is not in the antenna detection area JMKIA0063GB DEF-32

33 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A B When Intelligent Key is in the antenna detection area C 63 (P) Front outside handle RH antenna (+) When the front door RH request switch is operated with ignition switch When Intelligent Key is not in the antenna detection area JMKIA0062GB D E F JMKIA0063GB G When Intelligent Key is in the antenna detection area H 64 (V) Front outside handle LH antenna (-) When the front door LH request switch is operated with ignition switch JMKIA0062GB I J When Intelligent Key is not in the antenna detection area K JMKIA0063GB DEF M When Intelligent Key is in the antenna detection area N 65 (P) Front outside handle LH antenna (+) When the front door LH request switch is operated with ignition switch JMKIA0062GB O When Intelligent Key is not in the antenna detection area P JMKIA0063GB DEF-33

34 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) When Intelligent Key is in the passenger compartment JMKIA0062GB 66 (R) Instrument panel antenna (-) Ignition switch When Intelligent Key is not in the passenger compartment JMKIA0063GB When Intelligent Key is in the passenger compartment JMKIA0062GB 67 (G) Instrument panel antenna (+) Ignition switch When Intelligent Key is not in the passenger compartment JMKIA0063GB 68 (G/O) NATS antenna amp (built in key slot) Input/ During waiting Ignition switch is pressed while inserting the Intelligent Key into the key slot. Just after pressing ignition switch. Pointer of tester should move. 69 (O) NATS antenna amp (built in key slot) Input/ During waiting Ignition switch is pressed while inserting the Intelligent Key into the key slot. Just after pressing ignition switch. Pointer of tester should move. 70 (R/B) Ignition relay-2 control Ignition switch or ACC Battery voltage DEF-34

35 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A B During waiting C 71 (L/O) Remote keyless entry receiver signal Input/ JMKIA0064GB D E When operating either button on Intelligent Key F JMKIA0065GB G All switch (Wiper intermittent dial 4) H 1.4V JPMIA0041GB I J 75 (R/Y) Combination switch INPUT 5 Input Combination switch Front fog lamp switch (Wiper intermittent dial 4) K 1.3V JPMIA0037GB DEF Any of the conditions below with all switch Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 6 Wiper intermittent dial 7 1.3V JPMIA0040GB M N O P DEF-35

36 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) All switch (Wiper intermittent dial 4) 1.4V JPMIA0041GB Lighting switch high-beam (Wiper intermittent dial 4) 76 (R/G) Combination switch INPUT 3 Input Combination switch 1.3V JPMIA0036GB Lighting switch 2ND (Wiper intermittent dial 4) 1.3V JPMIA0037GB Any of the conditions below with all switch Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 3 1.3V JPMIA0040GB 77 (BR) Engine switch (push switch) Input Engine switch (push switch) Pressed Not pressed Battery voltage 78 (P) CAN-L Input/ 79 (L) CAN-H Input/ 80 (R/L) Key slot illumination Key slot illumination Blinking 6.5V Battery voltage JPMIA0015GB DEF-36

37 Terminal No. (Wire color) (+) (-) 81 (Y/L) 83 (L) 84 (Y/R) 85 (L/O) 86 (G/R) 87 (G/B) indicator lamp Ignition switch ACC relay control Ignition switch or ACC ACC or Battery voltage Battery voltage A/T device Battery voltage Description Signal name Electronic steering column lock condition No. 1 Electronic steering column lock condition No. 2 Selector lever P position switch Input/ Input Input Input Electronic steering column lock Electronic steering column lock Selector lever Condition Lock status Unlock status Lock status Unlock status P position Any position other than P (pressed) Battery voltage Battery voltage Battery voltage Value (Approx.) A B C D E F G 88 (R) Front door RH request switch Input Front door RH request switch (not pressed) H 1. JPMIA0016GB I (pressed) J 89 (R) Front door LH request switch Input Front door LH request switch (not pressed) K 1. JPMIA0016GB DEF 90 (Y) Blower fan motor relay control Ignition switch or ACC Battery voltage M 91 (L/R) Remote keyless entry receiver power supply Ignition switch Battery voltage N 94 (G/Y) Steering wheel lock unit power supply Ignition switch or ACC Battery voltage O P DEF-37

38 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) All switch 1.4V JPMIA0041GB Turn signal switch LH 1.3V JPMIA0037GB 95 (R/W) Combination switch INPUT 1 Input Combination switch (Wiper intermittent dial 4) Turn signal switch RH 1.3V JPMIA0036GB Front wiper switch LO 1.3V JPMIA0038GB Front washer switch 1.3V JPMIA0039GB DEF-38

39 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A B All switch (Wiper intermittent dial 4) C 1.4V JPMIA0041GB D E Lighting switch AUTO (Wiper intermittent dial 4) F 96 (P/B) Combination switch INPUT 4 Input Combination switch 1.3V JPMIA0038GB G Lighting switch 1ST (Wiper intermittent dial 4) H 1.3V JPMIA0036GB I Any of the conditions below with all switch Wiper intermittent dial 1 Wiper intermittent dial 5 Wiper intermittent dial 6 J K 1.3V JPMIA0039GB DEF M N O P DEF-39

40 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) All switch 1.4V JPMIA0041GB Lighting switch flash-topass 1.3V JPMIA0037GB 97 (R/B) Combination switch INPUT 2 Input Combination switch (Wiper intermittent dial 4) Lighting switch 2ND 1.3V JPMIA0036GB Front wiper switch INT 1.3V JPMIA0038GB Front wiper switch HI 1.3V JPMIA0040GB Pressed 0 V 98 (G/O) Hazard switch Input Hazard switch Not pressed 1.1V JPMIA0012GB DEF-40

41 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A LOCK status Battery voltage B 99 (L/Y) Electronic steering column lock unit communication Input/ Electronic steering column lock LOCK or UNLOCK JMKIA0066GB C D For 15 seconds after UN- LOCK Battery voltage E 103 (V) Trunk lid opening. Trunk lid 15 seconds or later after UNLOCK Open (trunk lid opener actuator is activated) Close (trunk lid opener actuator is not activated) Battery voltage F G 110 (V/W) Trunk room lamp Trunk room lamp Battery voltage H When Intelligent Key is in the passenger compartment JMKIA0062GB I J 114 (B) Trunk room antenna 1 (-) Ignition switch K When Intelligent Key is not in the passenger compartment DEF JMKIA0063GB M N O P DEF-41

42 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) When Intelligent Key is in the passenger compartment JMKIA0062GB 115 (W) Trunk room antenna 1 (+) Ignition switch When Intelligent Key is not in the passenger compartment JMKIA0063GB When Intelligent Key is in the antenna detection area 118 (L/O) Rear bumper antenna (-) When the trunk lid request switch is operated with ignition switch JMKIA0062GB When Intelligent Key is not in the antenna detection area JMKIA0063GB When Intelligent Key is in the antenna detection area 119 (BR/ W) Rear bumper antenna (+) When the trunk lid request switch is operated with ignition switch JMKIA0062GB When Intelligent Key is not in the antenna detection area JMKIA0063GB DEF-42

43 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A 127 (BR/ W) Ignition relay (IPDM E/R) control Ignition switch or ACC Battery voltage B C 130 (W) Trunk room lamp switch Input Trunk room lamp switch (trunk is closed) D 11.8V JPMIA0011GB E (trunk is open) 132 (R) Starter motor relay control Ignition switch (M/T vehicle) Ignition switch (other than M/ T vehicle) When the clutch pedal is depressed When the clutch pedal is not depressed When selector lever is in P or N position and the brake is depressed When selector lever is in P or N position and the brake is not depressed Battery voltage Battery voltage F G H (pressed) I 141 (BR) Trunk request switch Input Trunk request switch (not pressed) J K 1. JPMIA0016GB 144 (GR) Request switch buzzer Request switch buzzer Sounding Not sounding Battery voltage DEF 147 (L/R) Trunk lid opener switch Input Trunk lid opener switch Pressed Not pressed Battery voltage M N 148 (R/W) Rear door RH switch Input Rear door RH switch (when rear door RH closes) O (when rear door RH opens) 11.8V JPMIA0011GB P DEF-43

44 Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) 149 (R/B) Rear door LH switch Input Rear door LH switch (when rear door LH closes) 11.8V JPMIA0011GB (when rear door LH opens) DEF-44

45 Wiring Diagram INFOID: A B C D E F G H I J K DEF M N O ABLWA0134GB P DEF-45

46 ABLWA0135GB DEF-46

47 A B C D E F G H I J K DEF M N O ABLIA0475GB P DEF-47

48 ABLIA0476GB DEF-48

49 A B C D E F G H I J K DEF M N O ABLIA0477GB P DEF-49

50 ABLIA0478GB DEF-50

51 A B C D E F G H I J K DEF M N O ABLIA0480GB P DEF-51

52 ABLIA0481GB DEF-52

53 A B C D E F G H I J K DEF M N O Fail Safe ABLIA0482GB INFOID: P Display contents of CSULT Fail-safe Cancellation B2013: ID DISCORD BCM-S/L Inhibit engine cranking Erase DTC B2014: CHAIN OF S/L-BCM Inhibit engine cranking Erase DTC B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC DEF-53

54 Display contents of CSULT Fail-safe Cancellation B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC B2195: ANTI-SCANNING Inhibit engine cranking Erase DTC B2557: VEHICLE SPEED Inhibit electronic steering column lock B2560: STARTER CT RELAY Inhibit engine cranking B2562: LO VOLTAGE B2601: SHIFT POSITI B2602: SHIFT POSITI B2603: SHIFT POSI STATUS B2604: PNP SW B2605: PNP SW Inhibit engine cranking Inhibit electronic steering column lock Inhibit electronic steering column lock Inhibit electronic steering column lock Inhibit electronic steering column lock Inhibit electronic steering column lock Inhibit electronic steering column lock B2606: S/L RELAY Inhibit engine cranking B2607: S/L RELAY Inhibit engine cranking When normal vehicle speed signals have been received from ABS actuator and electric unit (control unit) for 500 ms 500 ms after the following CAN signal communication status has become consistent Starter control relay signal Starter relay status signal 100 ms after the power supply voltage increases to more than 8.8 V 500 ms after the following signal reception status becomes consistent Selector lever P position switch signal P range signal (CAN) 5 seconds after the following BCM recognition conditions are fulfilled Ignition switch is in the position Selector lever P position switch signal: Except P position (battery voltage) Vehicle speed: 4 km/h or more 500 ms after the following BCM recognition conditions are fulfilled Ignition switch is in the position Selector lever P position switch signal: Except P position (battery voltage) Selector lever P/N position signal: Except P and N positions (0 V) 500 ms after any of the following BCM recognition conditions is fulfilled Status 1 - Ignition switch is in the position - Selector lever P/N position signal: P and N position (battery voltage) - P range signal or N range signal (CAN): Status 2 - Ignition switch is in the position - Selector lever P/N position signal: Except P and N positions (0 V) - P range signal and N range signal (CAN): 500 ms after any of the following BCM recognition conditions is fulfilled Ignition switch is in the position - Power position: IGN - Selector lever P/N position signal: Except P and N positions (0 V) - Interlock/PNP switch signal (CAN): Status 2 - Ignition switch is in the position - Selector lever P/N position signal: P or N position (battery voltage) - PNP switch signal (CAN): 500 ms after the following CAN signal communication status has become consistent Electronic steering column lock relay signal (Request signal) Electronic steering column lock relay signal (Condition signal) 500 ms after the following CAN signal communication status has become consistent Electronic steering column lock relay signal (Request signal) Electronic steering column lock relay signal (Condition signal) DEF-54

55 Display contents of CSULT Fail-safe Cancellation B2608: STARTER RELAY Inhibit engine cranking B2609: S/L STATUS B260A: IGNITI RELAY B260F: ENG STATE SIG LOST B2612: S/L STATUS DTC Inspection Priority Chart Inhibit engine cranking Inhibit electronic steering column lock Inhibit engine cranking Maintains the power supply position attained at the time of DTC detection Inhibit engine cranking Inhibit electronic steering column lock B2617: STARTER RELAY CIRC Inhibit engine cranking B2618: BCM Inhibit engine cranking B2619: BCM Inhibit engine cranking B26E1: ENG STATE NO RECIV 500 ms after the following signal communication status becomes consistent Starter motor relay control signal Starter relay status signal (CAN) When the following electronic steering column lock conditions agree BCM electronic steering column lock control status Electronic steering column lock condition No. 1 signal status Electronic steering column lock condition No. 2 signal status 500 ms after the following conditions are fulfilled IGN relay (IPDM E/R) control signal: (Battery voltage) Ignition signal (CAN to IPDM E/R): (Request signal) Ignition signal (CAN from IPDM E/R): (Condition signal) When any of the following conditions is fulfilled Power position changes to ACC Receives engine status signal (CAN) When any of the following conditions is fulfilled Electronic steering column lock unit status signal (CAN) is received normally The BCM electronic steering column lock control status matches the electronic steering column lock status recognized by the electronic steering column lock unit status signal (CAN from IPDM E/R) 1 second after the starter motor relay control inside BCM becomes normal 1 second after the ignition relay (IPDM E/R) control inside BCM becomes normal 1 second after the electronic steering column lock unit power supply output control inside BCM becomes normal INFOID: If some DTCs are displayed at the same time, perform inspections one by one based on the following priority chart. Priority 1 B2562: LO VOLTAGE 2 3 Inhibit engine cranking U1000: CAN COMM CIRCUIT U1010: CTROL UNIT (CAN) B2190: NATS ANTENNA AMP B2191: DIFFERENCE OF KEY B2192: ID DISCORD BCM-ECM B2193: CHAIN OF BCM-ECM When any of the following conditions are fulfilled Power position changes to ACC Receives engine status signal (CAN) DTC A B C D E F G H I J K DEF M N O P DEF-55