DIAGNOSIS SYSTEM (IPDM E/R)

Size: px

Start display at page:

Download "DIAGNOSIS SYSTEM (IPDM E/R)"

Miles Bryant
5 years ago
Views:

2008 Pathfinder DIAGSIS SYSTEM (IPDM E/) Diagnosis INFOID:0000000001712742 eport a problem with this article AUTO ACTIVE TEST In auto active test mode, the IPDM E/ sends a drive signal to the

1 2008 Pathfinder DIAGSIS SYSTEM (IPDM E/) Diagnosis INFOID: eport a problem with this article AUTO ACTIVE TEST In auto active test mode, the IPDM E/ sends a drive signal to the following systems to check their operation. Oil pressure low warning indicator Oil pressure gauge ear window defogger Front wipers Tail, license and parking lamps Front fog lamps Headlamps (Hi, Lo) A/C compressor (magnetic clutch) Cooling fan Procedure 1. Close the hood and front door H, and lift the wiper arms from the windshield (to prevent windshield damage due to wiper operation). When auto active test is performed with hood opened, sprinkle water on windshield before hand. 2. Turn ignition switch. 3. Turn the ignition switch ON and, within 20 seconds, press the front door switch LH 10 times. Then turn the ignition switch. 4. Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test starts. 5. After a series of the following operations is repeated 3 times, auto active test is completed. When auto active test mode has to be cancelled halfway through test, turn ignition switch. CAUTION: If auto active test mode cannot be actuated, check door switch system. efer to DLK-59, "" (with Intelligent Key system), DLK-234, "" (without Intelligent Key system). Do not start the engine. Inspection in Auto Active Test Mode When auto active test mode is actuated, the following 7 steps are repeated 3 times. WKIA4991E sequence Inspection Location 1 ear window defogger 10 seconds 2 Front wipers LO for 5 seconds HI for 5 seconds 1/5

sequence Inspection Location 3 Tail, license, front fog and parking lamps 10 seconds 4 Headlamps LO for 10 seconds HI on-off for 5 seconds 5 A/C compressor (magnetic clutch) ON 5 times 6 Cooling fan

2 sequence Inspection Location 3 Tail, license, front fog and parking lamps 10 seconds 4 Headlamps LO for 10 seconds HI on-off for 5 seconds 5 A/C compressor (magnetic clutch) ON 5 times 6 Cooling fan 10 seconds Concept of auto active test WKIA5163E IPDM E/ starts the auto active test with the door switch signals transmitted by BCM via CAN Therefore, the CAN communication line between IPDM E/ and BCM is considered normal if the auto active test starts successfully. The auto active test facilitates troubleshooting if any systems controlled by IPDM E/ cannot be operated. Diagnosis chart in auto active test mode Symptom Inspection contents Possible cause Oil pressure low warning indicator does not operate Oil pressure gauge does not operate Does the oil pressure low warning indicator operate? Does the oil pressure gauge operate? IPDM E/ signal input circuit ECM signal input circuit between ECM and combination meter between IPDM E/, BCM and combination meter IPDM E/ signal input circuit between IPDM E/, BCM and combination meter BCM signal input circuit A/C and AV switch assembly and AV control ear window defogger does not operate Does the rear window defog- unit ger operate? between BCM and IPDM E/ 2/5

3 Symptom Inspection contents Possible cause BCM signal input system Lamp or front wiper motor Any of the following components do not operate malfunction Front wipers Lamp or front wiper motor Tail lamps ground circuit License plate lamps Does the applicable system Harness or connector be- Parking lamps operate? tween IPDM E/ and appli- Front fog lamps cable system Headlamps (Hi, Lo) IPDM E/ (integrated relay A/C compressor does not operate Does the A/C compressor operate? BCM signal input circuit between BCM and ECM between ECM and IPDM E/ Magnetic clutch malfunction IPDM E/ and magnetic clutch IPDM E/ (integrated relay ECM signal input circuit between ECM and IPDM E/ Cooling fan does not operate Does the cooling fan operate? Cooling fan motor malfunction IPDM E/ and cooling fan IPDM E/ (integrated relay CONSULT - III Function (IPDM E/) INFOID: APPLICATION ITEM CONSULT-III performs the following functions via CAN communication with IPDM E/. Diagnosis mode ECU Identification Self Diagnostic esult Data Monitor Active Test CAN Diag Support Monitor Allows confirmation of IPDM E/ part number. Displays the diagnosis results judged by IPDM E/. Displays the real-time input/output data from IPDM E/ input/output data. IPDM E/ can provide a drive signal to electronic components to check their operations. The results of transmit/receive diagnosis of CAN communication can be read. SELF DIAGSTIC efer to PCS-30, "DTC Index". DATA MONITO Monitor item 3/5

4 Monitor Item [Unit] MAIN SIG- NALS MOTO FAN EQ Displays the status of the cooling fan speed request signal received from ECM via [1/2/3/4] CAN A/C COMP EQ TAIL&CL EQ HL LO EQ HL HI EQ F FOG EQ HL WASHE EQ F WIP EQ [STOP/1LOW/LOW/HI] WIP AUTO STOP [STOP P/ACT P] WIP POT [/Block] ST LY EQ IGN LY DEF EQ OIL P SW [OPEN/CLOSE] DTL EQ [] HOOD SW [OPEN/CLOSE] THFT HN EQ HON CHIP ACTIVE TEST Test item Displays the status of the A/C request signal received from AV control unit via CAN Displays the status of the position light request signal received from BCM via CAN Displays the status of the low beam request signal received from BCM via CAN Displays the status of the high beam request signal received from BCM via CAN Displays the status of the front fog lamp request signal received from BCM via CAN Displays the status of the front wiper request signal received from BCM via CAN Displays the status of the front wiper auto stop signal judged by IPDM E/. Displays the status of the front wiper fail-safe operation judged by IPDM E/. Displays the status of the starter request signal received from ECM via CAN Displays the status of the ignition relay judged by IPDM E/. Displays the status of the rear defogger request signal received from AV control unit via CAN Displays the status of the oil pressure switch judged by IPDM E/. Displays the status of the theft warning horn request signal received from BCM via CAN Displays the status of the horn reminder signal received from BCM via CAN Test item EA DEFOGGE ON Operates rear window defogger relay. FONT WIPE LO Operates the front wiper relay. HI Operates the front wiper relay and front wiper high relay. HEAD LAMP WASHE ON 4/5

5 Test item 1 2 MOTO FAN 3 Operates the cooling fan relay. 4 Operates the cooling fan relay. TAIL Operates the tail lamp relay. LO Operates the headlamp low relay. EXTENAL LAMPS Operates the headlamp low relay and ON/ the headlamp high relay at 1 sec- HI ond intervals. FOG Operates the front fog lamp relay HON ON Operates horn relay for 20 ms. 5/5

DIAGNOSIS SYSTEM (IPDM E/R)

2008 Altima DIAGNOSIS SYSTEM (IPDM E/R) Diagnosis INFOID:0000000001342651 Report a problem with this article AUTO ACTIVE TEST In auto active test mode, the IPDM E/R sends a drive signal to the following